ISL89410IP

DATASHEET ISL89410, ISL89411, ISL89412 FN6798 Rev 2.00 October 16, 2015 High Speed, Dual Channel Power MOSFET Drivers The ISL89410, ISL89411, ISL89412 ICs are similar to the EL7202, EL7212, EL7222 series but with greater VDD ratings. These are very high speed matched dual drivers capable of delivering peak currents of 2.0A into highly capacitive loads. The high speed performance is achieved by means of a proprietary “Turbo-Driver” circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10-fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques. Pinouts ISL89410 (8 LD PDIP, SOIC) TOP VIEW ISL89411 (8 LD PDIP, SOIC) TOP VIEW Features • Industry Standard Driver Replacement • Improved Response Times • Matched Rise and Fall Times • Reduced Clock Skew • Low Output Impedance • Low Input Capacitance • High Noise Immunity • Improved Clocking Rate • Low Supply Current • Wide Operating Voltage Range • Pb-Free Available (RoHS compliant) Applications • Clock/line Drivers • CCD Drivers NC 1 8 NC NC 1 8 NC INA 2 7 OUTA INA 2 7 OUTA GND 3 6 V+ GND 3 6 V+ • Power MOSFET Drivers INB 4 5 OUTB INB 4 5 OUTB • Switch Mode Power Supplies INVERTING DRIVERS NON-INVERTING DRIVERS • Ultra-Sound Transducer Drivers • Class D Switching Amplifiers • Ultrasonic and RF Generators • Pulsed Circuits Pin Descriptions ISL89412 (8 LD PDIP, SOIC) TOP VIEW SYMBOL V+ NC 1 8 NC GND INA 2 7 OUTA GND 3 6 v+ INB 4 5 OUTB INA, INB COMPLEMENTARY DRIVERS PIN DESCRIPTIONS Power voltage from 4.5V to 18V. Power voltage return Logic inputs. OUTA OUTA Non-inverted ouput for ISL89410. Inverted output for ISL89411 and ISL89412. OUTB OUTB Non-inverted output for ISL89410 and ISL89412. Inverted output for ISL89411. NC These pins must be left unconnected. Manufactured under U.S. Patent Nos. 5,334,883, #5,341,047 Ordering Information PART NUMBER ISL89410IPZ (Note) (No longer available, recommended replacement: ISL89410IBZ) FN6798 Rev 2.00 October 16, 2015 PART MARKING 89410 IPZ TEMP. RANGE (°C) -40 to +85 PACKAGE 8 Ld PDIP** (Pb-free) PKG. DWG. # E8.3 Page 1 of 10 ISL89410, ISL89411, ISL89412 Ordering Information PART NUMBER PART MARKING TEMP. RANGE (°C) PACKAGE PKG. DWG. # ISL89410IBZ (Note) 89410 IBZ -40 to +85 8 Ld SOIC (Pb-free) M8.15E ISL89410IBZ-T13* (Note) 89410 IBZ -40 to +85 8 Ld SOIC (Tape and Reel) (Pb-free) M8.15E ISL89411IPZ (Note) ISL 89411IPZ -40 to +85 8 Ld PDIP** (Pb-free) E8.3 ISL89411IBZ (Note) 89411 IBZ -40 to +85 8 Ld SOIC (Pb-free) M8.15E ISL89411IBZ-T13* (Note) 89411 IBZ -40 to +85 8 Ld SOIC (Tape and Reel) (Pb-free) M8.15E ISL89412IPZ (No longer available, recommended replacement: ISL89412IBZ) 89412 IPZ -40 to +85 8 Ld PDIP** (Pb-free) E8.3 ISL89412IBZ (Note) 89412 IBZ -40 to +85 8 Ld SOIC (Pb-free) M8.15E ISL89412IBZ-T13* (Note) 89412 IBZ -40 to +85 8 Ld SOIC (Tape and Reel) (Pb-free) M8.15E *Please refer to TB347 for details on reel specifications. **Pb-free PDIPs can be used for through-hole wave solder processing only. They are not intended for use in Reflow solder processing applications NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. FN6798 Rev 2.00 October 16, 2015 Page 2 of 10 ISL89410, ISL89411, ISL89412 Absolute Maximum Ratings Thermal Information Supply (V+ to GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.0V Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V above V+ Combined Peak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . .4A Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +125°C Power Dissipation 8 Ld SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .570mW 8 Ld PDIP* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1050mW Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp *Pb-free PDIPs can be used for through-hole wave solder processing only. They are not intended for use in Reflow solder processing applications. Maximum Recommended Operating Conditions Recommended Operating V+ Range. . . . . . . . . . . . . . 4.5V to 18.0V Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to V+ CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA DC Electrical Specifications TA = +25°C, V = 18V unless otherwise specified; Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. PARAMETER DESCRIPTION TEST CONDITIONS MIN TYP MAX UNITS INPUT VIH Logic “1” Input Voltage IIH Logic “1” Input Current VIL Logic “0” Input Voltage IIL Logic “0” Input Current VHVS Input Hysteresis 2.4 @V+ V 0.1 @0V 0.1 10 µA 0.8 V 10 µA 0.3 V OUTPUT ROH Pull-Up Resistance IOUT = -100mA 3 6  ROL Pull-Down Resistance IOUT = +100mA 4 6  IPK Peak Output Current Source 2 IDC Continuous Output Current Source/Sink Power Supply Current Inputs High/ISL89410 4.5 7.5 mA Inputs High/ISL89411 1 2.5 mA 2.5 5.0 mA 18 V MAX UNITS Sink A 2 A 100 mA POWER SUPPLY IS Inputs High/ISL89412 VS Operating Voltage AC Electrical Specifications PARAMETER 4.5 TA = +25°C, V = 18V unless otherwise specified. DESCRIPTION TEST CONDITIONS MIN TYP SWITCHING CHARACTERISTICS tR Rise Time (Note 1) tF Fall Time (Note 1) CL = 500pF 7.5 CL = 1000pF 10 CL = 500pF 10 CL = 1000pF 13 ns 20 ns ns 20 ns tD1 Turn-On Delay Time (Note 1) See “Timing Table” on page 4 18 25 ns tD2 Turn-Off Delay Time (Note 1) See“Timing Table” on page 4 20 25 ns NOTE: 1. Limits established by characterization and are not production tested. FN6798 Rev 2.00 October 16, 2015 Page 3 of 10 ISL89410, ISL89411, ISL89412 Timing Table 5V INPUT 2.5V 0 INVERTED OUTPUT 90% 10% 90% NON-INVERTED OUTPUT 10% tD1 tD2 tF tR tF tR Standard Test Configuration V+ 4 6 4.7µF TAN+ 7 2 INPUT OUTPUT 1000pF 3 Simplified Schematic V+ + - INPUT + OUTPUT VREF INPUT BUFFER FN6798 Rev 2.00 October 16, 2015 REFERENCE AND LEVEL SHIFTER INVERTING BUFFER WITH HYSTERESIS 2ND INVERTING BUFFER SUPER INVERTER Page 4 of 10 ISL89410, ISL89411, ISL89412 Typical Performance Curves FIGURE 1. MAX POWER/DERATING CURVES FIGURE 3. INPUT CURRENT vs VOLTAGE FIGURE 2. SWITCH THRESHOLD vs SUPPLY VOLTAGE FIGURE 4. PEAK DRIVE vs SUPPLY VOLTAGE ISL89410 ISL89411 ISL89412 FIGURE 5. QUIESCENT SUPPLY CURRENT FN6798 Rev 2.00 October 16, 2015 Page 5 of 10 ISL89410, ISL89411, ISL89412 Typical Performance Curves (Continued) FIGURE 6. “ON” RESISTANCE vs SUPPLY VOLTAGE FIGURE 7. AVERAGE SUPPLY CURRENT vs VOLTAGE AND FREQUENCY FIGURE 8. AVERAGE SUPPLY CURRENT vs CAPACITIVE LOAD FIGURE 9. RISE/FALL TIME vs LOAD FIGURE 10. RISE/FALL TIME vs SUPPLY VOLTAGE FIGURE 11. PROPAGATION DELAY vs SUPPLY VOLTAGE FN6798 Rev 2.00 October 16, 2015 Page 6 of 10 ISL89410, ISL89411, ISL89412 Typical Performance Curves (Continued) FIGURE 12. RISE/FALL TIME vs TEMPERATURE FIGURE 13. DELAY vs TEMPERATURE ISL89411 Macro Model **** ISL89411 Model **** * input * | gnd * | | Vsupply * | | | Vout .subckt M89411 2 3 6 7 V1 12 3 1.6 R1 13 15 1k R2 14 15 5k R5 11 12 100 C1 15 3 43.3 pF D1 14 13 dmod X1 13 11 2 3 comp1 X2 16 12 15 3 comp1 sp 6 7 16 3 spmod sn 7 3 16 3 snmod g1 11 0 13 0 938µ .model dmod d .model spmod vswitch ron3 roff2meg von1 voff1.5 .model snmod vswitch ron4 roff2meg von3 voff2 .ends M89411 FN6798 Rev 2.00 October 16, 2015 Page 7 of 10 ISL89410, ISL89411, ISL89412 .subckt comp1 out inp inm vss e1 out vss table { (v(inp) v(inm))* 5000} (0,0) (3.2,3.2) Rout out vss 10meg Rinp inp vss 10meg Rinm inm vss 10meg .ends comp1 V+ PARASITIC LEAD INDUCTANCE Cq Application Guidelines It is important to minimize inductance to the power FET by keeping the output drive current loop as short as possible. Also, the decoupling capacitor, Cq, should be a high quality ceramic capacitor with a Q that should be a least 10x the gate Q of the power FET. A ground plane under this circuit is also recommended. V+ Cq SHOULD BE AS CLOSE AS POSSIBLE TO THE V+ AND GND PINS Cq GND FIGURE 15. SUGGESTED CONFIGURATION FOR DRIVING INDUCTIVE LOADS Where high supply voltage operation is required (15V to 18V), input signals with a minimum of 3.3V input drive is suggested and a minimum rise/fall time of 100ns. This is recommended to minimize the internal bias current power dissipation. Excessive power dissipation in the driver can result when driving highly capacitive FET gates at high frequencies. These gate power losses are defined by Equation 1: LOOP AS SHORT AS POSSIBLE GND FIGURE 14. RECOMMENDED LAYOUT METHODS In applications where it is difficult to place the driver very close to the power FET (which may result with excessive parasitic inductance), it then may be necessary to add an external gate resistor to dampen the inductive ring. If this resistor must be too large in value to be effective, then as an alternative, Schottky diodes can be added to clamp the ring voltage to V+ or GND. P = 2  Q C  V gs  f SW (EQ. 1) where: P = Power Qc = Charge of the Power FET at Vgs Vgs = Gate drive voltage (V+) fSW = switching Frequency Adding a gate resistor to the output of the driver will transfer some of the driver dissipation to the resistor. Another possible solution is to lower the gate driver voltage which also lowers Qc. Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION October 16, 2015 FN6798.2 CHANGE Updated Ordering Information Table on page 1. Added Revision History and About Intersil sections. Updated POD MDP0027 to M8.15E. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support FN6798 Rev 2.00 October 16, 2015 Page 8 of 10 ISL89410, ISL89411, ISL89412 Package Outline Drawing M8.15E 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 0, 08/09 4 4.90 ± 0.10 A DETAIL "A" 0.22 ± 0.03 B 6.0 ± 0.20 3.90 ± 0.10 4 PIN NO.1 ID MARK 5 (0.35) x 45° 4° ± 4° 0.43 ± 0.076 1.27 0.25 M C A B SIDE VIEW “B” TOP VIEW 1.75 MAX 1.45 ± 0.1 0.25 GAUGE PLANE C SEATING PLANE 0.10 C 0.175 ± 0.075 SIDE VIEW “A 0.63 ±0.23 DETAIL "A" (1.27) (0.60) NOTES: (1.50) (5.40) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25mm per side. 5. The pin #1 identifier may be either a mold or mark feature. 6. Reference to JEDEC MS-012. TYPICAL RECOMMENDED LAND PATTERN FN6798 Rev 2.00 October 16, 2015 Page 9 of 10 ISL89410, ISL89411, ISL89412 Dual-In-Line Plastic Packages (PDIP) E8.3 (JEDEC MS-001-BA ISSUE D) N 8 LEAD DUAL-IN-LINE PLASTIC PACKAGE E1 INDEX AREA 1 2 3 INCHES N/2 -B- -AD E BASE PLANE -C- SEATING PLANE A2 A L D1 e B1 D1 A1 eC B 0.010 (0.25) M C A B S MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A - 0.210 - 5.33 4 A1 0.015 - 0.39 - 4 A2 0.115 0.195 2.93 4.95 - B 0.014 0.022 0.356 0.558 - C L B1 0.045 0.070 1.15 1.77 8, 10 eA C 0.008 0.014 0.204 C D 0.355 0.400 9.01 eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 5 D1 0.005 - 0.13 - 5 E 0.300 0.325 7.62 8.25 6 E1 0.240 0.280 6.10 7.11 5 e 0.100 BSC 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. eA 0.300 BSC 3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication No. 95. eB - L 0.115 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. 0.355 10.16 N 2.54 BSC 7.62 BSC 0.430 - 0.150 2.93 8 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 8 6 10.92 7 3.81 4 9 Rev. 0 12/93 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). © Copyright Intersil Americas LLC 2008-2015. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN6798 Rev 2.00 October 16, 2015 Page 10 of 10