7.0V to 26V Input, 1.0A, Integrated MOSFET
Single Synchronous Buck DC/DC Converter
BD9E102FJ
General Description
The BD9E102FJ is a synchronous buck switching
regulator with low on-resistance built-in power MOSFETs.
High efficiency at light load with a SLLMTM. It is most
suitable for use in the equipment to reduce the standby
power is required. It is a current mode control DC/DC
converter and features high-speed transient response.
Phase compensation can also be set easily.
Key Specifications
Input voltage range:
7.0V to 26V
Adjustable output voltage range: 1.0V to VIN x 0.7V
Maximum output current:
1.0 A (Max.)
Switching frequency:
570 kHz (Typ.)
High-Side MOSFET on-resistance: 250 mΩ (Typ.)
Low-Side MOSFET on-resistance: 200 mΩ (Typ.)
Shutdown current:
0 μA (Typ.)
Features
Synchronous single DC/DC converter
TM
SLLM control (Simple Light Load Mode)
Efficiency = 80% (@IOUT=10mA)
Over current protection
Short circuit protection
Thermal shutdown protection
Undervoltage lockout protection
Soft start
Reduce external diode
SOP-J8 package
Package
SOP-J8
W (Typ.) x D (Typ.) x H (Max.)
4.90 mm x 6.00 mm x 1.65 mm
Applications
Consumer applications such as home appliance
Secondary power supply and Adapter equipments
Telecommunication devices
SOP-J8
Typical Application Circuit
Figure 1. Application circuit
○Product structure：Silicon monolithic integrated circuit.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
○This product is not designed for protection against radioactive rays.
1/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Pin Configuration
(TOP VIEW)
BOOT
1
8
SW
VIN
2
7
PGND
EN
3
6
COMP
AGND
4
5
FB
Figure 2. Pin assignment
Pin Descriptions
Pin No.
Pin Name
Description
1
BOOT
2
VIN
Power supply terminal for the switching regulator and control circuit.
Connecting a 10 µF ceramic capacitor is recommended.
3
EN
Turning this terminal signal low-level (0.8 V or lower) forces the device to enter the shut
down mode. Turning this terminal signal high-level (2.0 V or higher) enables the device.
This terminal must be terminated.
4
AGND
5
FB
Connect a bootstrap capacitor of 0.1 µF between this terminal and SW terminals.
The voltage of this capacitor is the gate drive voltage of the high-side MOSFET.
Ground terminal for the control circuit.
Inverting input node for the gm error amplifier.
See page 22 for how to calculate the resistance of the output voltage setting.
6
COMP
Input terminal for the gm error amplifier output and the output switch current comparator.
Connect a frequency phase compensation component to this terminal.
See page 22 for how to calculate the resistance and capacitance for phase
compensation.
7
PGND
Ground terminals for the output stage of the switching regulator.
8
SW
Switch node. This terminal is connected to the source of the high-side MOSFET and
drain of the low-side MOSFET. Connect a bootstrap capacitor of 0.1 µF between these
terminals and BOOT terminals. In addition, connect an inductor of 6.8 µH with attention
paid to theconsidering the direct current superimposition characteristic.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
2/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Block Diagram
EN
3
VREG3
3V
VREG
5V
1
BOOTREG
BOOT
SCP
UVLO
OSC
VIN
OVP
TSD
2
OCP
VIN
S
SLLMTM
DRIVER
8
ERR
SW
VOUT
LOGIC
FB
5
SLOPE
COMP
PWM
R
6
7
PGND
SOFT
START
4
AGND
Figure 3. Block diagram
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
3/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Description of Blocks
VREG3
Block creating internal reference voltage 3V (typ.).
VREG
Block creating internal reference voltage 5V (typ.).
BOOTREG
Block creating gate drive voltage.
TSD
This is thermal shutdown block. Thermal shutdown circuit shuts down when inner part of IC becomes more than 175℃
(typ.). Also when the temperature degrease it returns with hysteresis of 25℃(typ.).
UVLO
This is under voltage lockout block. IC shuts down with VIN under 6.4V (typ.). Still the threshold voltage has hysteresis of
200mV (typ.).
ERR
Circuit to compares the feedback voltage of standard and output voltage. Switching duty is settled by this compared result
and COMP terminal voltage. Also, because soft start occurs at activation, COMP terminal voltage is controlled by internal
slope voltage.
OSC
Block generating oscillation frequency.
SLOPE
Creates delta wave from clock, generated by OSC, and sends voltage composed by current sense signal of high side
MOSFET and delta wave to PWM comparator.
PWM
Settles switching duty by comparing output COMP terminal voltage of error amplifier and signal of SLOPE part.
DRIVER LOGIC
This is DC/DC driver block. Input signal from PWM and drives MOSFET.
SOFT START
By controlling current output voltage starts calmly preventing over shoot of output voltage and inrush current.
OCP
Current flowing in high side MOSFET is controlled one circle each of switching frequency when over current occurs.
SCP
The short circuit protection block compares the FB terminal voltage with the internal standard voltage VREF. When the FB
terminal voltage has fallen below 0.56 V (typ.) and remained there for 0.9 msec (typ.), SCP stops the operation for 14.4
msec (typ.) and subsequently initiates a restart.
OVP
Over voltage protection function (OVP) compares FB terminal voltage with the internal standard voltage VREF. When the
FB terminal voltage exceeds 1.04V (typ.) it turns MOSFET of output part MOSFET OFF. After output voltage drop it
returns with hysteresis.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
4/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Absolute Maximum Ratings (Ta = 25C)
Parameter
Symbol
Rating
Unit
Supply Voltage
VIN
-0.3 to +30
V
EN Input Voltage
VEN
-0.3 to +30
V
VBOOT
-0.3 to +35
V
⊿VBOOT
-0.3 to +7
V
VFB
-0.3 to +7
V
VCOMP
-0.3 to +7
V
SW Input Voltage
VSW
-0.5 to +30
V
Output Current
IOUT
1.0
A
Pd
0.675*1
W
Operating Ambient Temperature Range
Topr
-40 to +85
C
Storage Temperature Range
Tstg
-55 to +150
C
Voltage from GND to BOOT
Voltage from SW to BOOT
FB Input Voltage
COMP Input Voltage
Allowable Power Dissipation
*1 When mounted on a 70 mm x 70 mm x 1.6 mm 1-layer glass epoxy board Derated by 5.4 mW/C for Ta 25C.
Recommended Operating Ratings
Parameter
Rating
Symbol
Min
Typ
Max
Unit
Supply Voltage
VIN
7.0
-
26
V
Output Current
IOUT
-
-
1.0
A
VRANGE
1.0*2
-
VIN × 0.7
V
Output Voltage Range
*2 Please use it in I/O voltage setting of which output pulse width does not become 250nsec (typ.) or less. See the page 22 for how to calculate the
resistance of the output voltage setting.
Electrical Characteristics
(Ta = 25C, VIN = 12 V, VEN = 3 V unless otherwise specified)
Parameter
Symbol
Limits
Min
Typ
Max
Unit
Conditions
Supply Current in Operating
Iopr
-
250
500
µA
VFB = 0.9V
Supply Current in Standby
Istby
-
0
10
µA
VEN = 0V
Reference Voltage
VFB
0.784
0.800
0.816
V
FB Input Current
IFB
-1
0
1
µA
Switching frequency
FOSC
484
570
656
kHz
Maximum Duty ratio
Maxduty
88
93
98
%
High-side FET on-resistance
RONH
-
250
-
mΩ
ISW = 100mA
Low-side FET on-resistance
RONL
-
200
-
mΩ
ISW = 100mA
Over Current limit
ILIMIT
1.9
2.2
2.5
A
UVLO detection voltage
VUVLO
6.1
6.4
6.7
V
UVLO hysteresis voltage
VUVLOHYS
100
200
300
mV
EN high-level input voltage
VENH
2.0
-
VIN
V
EN low-level input voltage
VENL
-
-
0.8
V
EN Input current
IEN
2
4
8
µA
Soft Start time
TSS
1.2
2.5
5.0
msec
●
●
VFB = 0V
VIN falling
VEN = 3V
VFB : FB Input Voltage. VEN : EN Input Voltage.
Pd should not be exceeded.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
5/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Typical Performance Curves
1.0
500
450
0.8
VIN =26V
350
Standby Current[µA]
Operating Current[µA]
400
VIN=12V
300
250
200
0.6
VIN =26V
VIN =12V
0.4
VIN =7V
150
0.2
VIN =7V
100
50
0.0
-40
-20
0
20
40
60
80
100 120
-40
-20
0
Temperature[℃]
40
60
80
100 120
Temperature[℃]
Figure 4. Operating Current - Temperature
Figure 5. Stand-by Current - Temperature
1.0
816
812
VIN =12V
0.8
VIN =26V
0.6
808
VIN =12V
804
VIN =7V
800
796
FB Input Current[µA]
Voltage Reference[mV]
20
792
0.4
0.2
0.0
-0.2
-0.4
-0.6
788
-0.8
784
-1.0
-40
-20
0
20
40
60
80
100 120
-40
Temperature[℃]
0
20
40
60
80
100 120
Temperature[℃]
Figure 6. FB Voltage Reference - Temperature
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
-20
Figure 7. FB Input Current - Temperature
6/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
656
98
97
96
613
VIN =7V
95
VIN =12V
Maximum Duty[%]
Switching Frequency[kHz]
VIN =7V
570
94
93
92
VIN =12V
91
527
VIN =26V
90
VIN =26V
89
484
88
-40
-20
0
20
40
60
80
100 120
-40
-20
0
20
Temperature[℃]
60
80
100
120
Temperature[℃]
Figure 8. Switching Frequency - Temperature
Figure 9. Maximum Duty - Temperature
400
450
VIN =12V
VIN =12V
350
Low Side MOSFET On-Resistance[mΩ]
400
High Side MOSFET On-Resistance[mΩ]
40
350
300
250
200
150
100
50
-40
-20
0
20
40
60
80
250
200
150
100
50
0
-40
100 120
-20
0
20
40
60
80
100 120
Temperature[℃]
Temperature[℃]
Figure 10. High Side MOSFET On-ResistanceTemperature
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
300
Figure 11. Low Side MOSFET On-ResistanceTemperature
7/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
2.5
6.9
VIN =12V
6.8
2.4
6.7
VIN Input Voltage[V]
Current Limit[A]
VOUT =3.3V
2.3
2.2
VOUT =5.0V
2.1
VIN Sweep up
6.6
6.5
6.4
6.3
2.0
VIN Sweep down
VIN Sweep down
6.2
6.1
1.9
-40
-20
0
20
40
60
80
100 120
-40
-20
0
Temperature[℃]
20
40
60
80
100 120
Temperature[℃]
Figure 12. Current Limit - Temperature
Figure 13. UVLO Threshold - Temperature
300
2.0
275
EN Sweep up
1.8
VEN Input Voltage[V]
UVLO Hysteresis[mV]
250
225
200
175
1.6
EN Sweep down
1.4
1.2
150
1.0
125
0.8
100
-40
-20
0
20
40
60
80
-40
100 120
0
20
40
60
80
100 120
Temperature[℃]
Temperature[℃]
Figure 14. UVLO Hysteresis- Temperature
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
-20
Figure 15. EN Threshold - Temperature
8/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
8.0
5.0
EN=3V
7.0
6.0
Soft Start Time[ms]
EN Input Current[µA]
4.0
5.0
4.0
VIN =12V
VIN =7V
3.0
2.0
VIN =26V
3.0
1.0
2.0
-40
-20
0
20
40
60
80
-40
100 120
0
20
40
60
80
100 120
Temperature[℃]
Temperature[℃]
Figure 16. EN Input Current - Temperature
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
-20
Figure 17. Soft Start Time - Temperature
9/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Typical Performance Curves (Application)
100
100
90
90
80
80
70
VIN =7V
60
Efficiency[%]
Efficiency[%]
70
VIN =12V
50
VIN =18V
40
VIN =24V
30
VIN =7V
60
VIN =12V
50
VIN =18V
40
30
20
20
EN=3V
VOUT =5.0V
10
EN=3V
VOUT =3.3V
10
0
0
1
10
100
1000
1
10
100
1000
Output Current[mA]
Output Current[mA]
Figure 18. Efficiency - Output Current
(VOUT = 5.0V)
Figure 19. Efficiency - Output Current
(VOUT = 3.3V)
100
90
80
Efficiency[%]
70
60
VIN =7V
50
VIN =12V
40
VIN =18V
30
20
EN=3V
VOUT=1.8V
10
0
1
10
100
1000
Output Current[mA]
Figure 20. Efficiency - Output Current
(VOUT = 1.8V)
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
10/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
VIN=7V/div
VIN=7V/div
EN=7V/div
EN=7V/div
VOUT=2V/div
VOUT=2V/div
Time=2ms/div
Time=2ms/div
SW=5V/div
SW=5V/div
Figure 21. Power Up (VIN = EN)
Figure 22. Power Down (VIN = EN)
VIN=7V/div
VIN=7V/div
EN=2V/div
EN=2V/div
VOUT=2V/div
VOUT=2V/div
Time=2ms/div
Time=2ms/div
SW=5V/div
SW=5V/div
Figure 23. Power Up (EN = 0V→5V)
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
Figure 24. Power Down (EN = 5V→0V)
11/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
VOUT=20mV/div
SW=5V/div
VOUT=20mV/div
Time=20ms/div
SW=5V/div
Figure 25. VOUT Ripple
(VIN = 12V, VOUT = 5V, IOUT = 0A)
Figure 26. VOUT Ripple
(VIN = 12V, VOUT = 5V, IOUT = 1A)
VIN=50mV/div
SW=5V/div
VIN=50mV/div
SW=5V/div
Time=20ms/div
Figure 27. VIN Ripple
(VIN = 12V, VOUT = 5V, IOUT = 0A)
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
Time=1µs/div
Time=1µs/div
Figure 28. VIN Ripple
(VIN = 12V, VOUT = 5V, IOUT = 1A)
12/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
IL=1A/div
IL=1A/div
SW=5V/div
Time=1µs/div
Time=1µs/div
SW=5V/div
Figure 29. Switching Waveform
(VIN = 12V, VOUT = 5V, IOUT = 1A)
Figure 30. Switching Waveform
(VIN = 24V, VOUT = 5V, IOUT = 1A)
IL=500mA/div
Time=10µs/div
SW=5V/div
SLLMTM control
Figure 31. Switching Waveform
(VIN = 12V, VOUT = 5V, IOUT = 20mA)
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
13/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
2.0
2.0
1.5
1.5
1.0
1.0
Output Voltage Change[%]
Output Voltage Change[%]
BD9E102FJ
0.5
0.0
-0.5
-1.0
VOUT=5.0V
IOUT=1A
-1.5
0.5
0.0
-0.5
-1.0
VOUT=3.3V
IOUT=1A
-1.5
-2.0
-2.0
6
8
10
12
14
16
18
20
22
24
26
VIN Input Voltage[V]
6
8
10
12
14
16
18
20
22
24
26
VIN Input Voltage[V]
Figure 33. VOUT Line Regulation
(VOUT = 3.3V)
Figure 32. VOUT Line Regulation
(VOUT = 5.0V)
2.0
Output Voltage Change[%]
1.5
1.0
0.5
0.0
-0.5
-1.0
VOUT=1.8V
IOUT=1A
-1.5
-2.0
6
8
10
12
14
16
18
20
22
24
26
VIN Input Voltage[V]
Figure 34. VOUT Line Regulation
(VOUT = 1.8V)
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
14/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
2.0
2.0
1.5
1.5
1.0
1.0
Output Voltage Change[%]
Output Voltage Change[%]
BD9E102FJ
0.5
0.0
-0.5
-1.0
VIN=12V
VOUT=5.0V
-1.5
0.5
0.0
-0.5
-1.0
VIN=12V
VOUT=3.3V
-1.5
-2.0
-2.0
0
200
400
600
800
1000
Output Current[mA]
0
200
400
600
800
1000
Output Current[mA]
Figure 36. VOUT Load Regulation
(VOUT = 3.3V)
Figure 35. VOUT Load Regulation
(VOUT = 5.0V)
2.0
Output Voltage Change[%]
1.5
1.0
0.5
0.0
-0.5
-1.0
VIN=12V
VOUT=1.8V
-1.5
-2.0
0
200
400
600
800
1000
Output Current[mA]
Figure 37. VOUT Load Regulation
(VOUT = 1.8V)
)
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
15/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
180
VIN=12V
VOUT=5V
90
40
20
45
20
45
0
0
0
0
phase
-20
-45
gain
Gain[dB]
60
40
Gain[dB]
180
VIN=12V
VOUT=3.3V
135
Phase[deg]
60
80
135
90
phase
-20
-45
gain
-40
-90
-40
-90
-60
-135
-60
-135
-80
-180
-80
-180
1K
10K
100K
1K
1M
10K
100K
1M
Frequency[Hz]
Frequency[Hz]
Figure 38. Loop Response IOUT=1A
(VIN=12V, VOUT=5V, COUT=Ceramic10μF×3)
Figure 39. Loop Response IOUT=1A
(VIN=12V, VOUT=3.3V, COUT=Ceramic10μF×3)
VOUT=100mV/div
VOUT=100mV/div
Time=1ms/div
Time=1ms/div
IOUT=400mA/div
IOUT=400mA/div
Figure 40. Load Transient Response IOUT=10mA - 1A
(VIN=12V, VOUT=5V, COUT=Ceramic10μF×3)
Figure 41. Load Transient Response IOUT=10mA - 1A
(VIN=12V, VOUT=3.3V, COUT=Ceramic10μF×3)
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
Phase[deg]
80
16/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Function Description
1) DC/DC converter operation
BD9E102FJ is a synchronous rectifying step-down switching regulator that achieves faster transient response by
employing current mode PWM control system. It utilizes switching operation in PWM (Pulse Width Modulation) mode for
heavier load, while it utilizes SLLM (Simple Light Load Mode) control for lighter load to improve efficiency.
Efficiency η[%]
① SLLMTM control
② PWM control
Output current IOUT[A]
Figure 42. Efficiency (SLLMTM control and PWM control)
①SLLMTM control
②PWM control
VOUT =50mV/div
VOUT =50mV/div
Time=5µs/div
Time=5µs/div
SW=5V/div
SW=5V/div
Figure 43. SW Waveform (①SLLMTM control)
(VIN = 12V, VOUT = 5.0V, IOUT = 50mA)
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
Figure 44. SW Waveform (②PWM control)
(VIN = 12V, VOUT = 5.0V, IOUT = 1A)
17/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
2) Enable Control
The IC shutdown can be controlled by the voltage applied to the EN terminal. When EN voltage reaches 2.0 V (typ.), the
internal circuit is activated and the IC starts up. To enable shutdown control with the EN terminal, set the shutdown interval
(Low level interval of EN) must be set to 100 µs or longer.
EN terminal
Output setting voltage
Figure 45. Timing Chart with Enable Control
3) Protective Functions
The protective circuits are intended for prevention of damage caused by unexpected accidents. Do not use them
for continuous protective operation.
3-1) Short Circuit Protection (SCP)
The short circuit protection block compares the FB terminal voltage with the internal reference voltage VREF. When
the FB terminal voltage has fallen below 0.56 V (typ.) and remained there for 0.9 msec (typ.), SCP stops the operation
for 14.4 msec (typ.) and subsequently initiates a restart.
Table 1. Short circuit protection function
EN pin
2.0 V or higher
FB pin
< 0.56 V (typ.)
> 0.56 V (typ.)
0.8 V or lower
-
Short circuit
protection
Enabled
Disabled
Short circuit
protection operation
ON
OFF
OFF
Soft start
2.5msec (typ.)
VOUT
SCP detection time
0.9msec (typ.)
SCP detection time
0.9msec (typ.)
0.8V
FB terminal
SCP threshold voltage：
0.56Ｖ(typ.)
SCP detection released
Upper MOSFET
gate
LOW
Lower MOSFET
gate
LOW
OCP
Threshold
Coil current
IC internal
SCP signal
14.4msec (typ.)
SCP reset
Figure 46. Short circuit protection function (SCP) timing chart
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
18/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
3-2) Under Voltage Lockout Protection (UVLO)
The under voltage lockout protection circuit monitors the VIN terminal voltage.
The operation enters standby when the VIN terminal voltage is 6.4 V (typ.) or lower.
The operation starts when the VIN terminal voltage is 6.6 V (typ.) or higher.
VIN
UVLO OFF
UVLO ON
0V
hys
VOUT
Soft start
FB
terminal
High-side
MOSFET gate
Low-side
MOSFET gate
Normal operation
UVLO
Normal operation
Figure 47. UVLO Timing Chart
3-3) Thermal Shutdown Function (TSD)
When the chip temperature exceeds Tj = 175C, the DC/DC converter output is stopped. The thermal shutdown circuit is
intended for shutting down the IC from thermal runaway in an abnormal state with the temperature exceeding Tjmax =
150C. It is not meant to protect or guarantee the soundness of the application. Do not use the function of this circuit for
application protection design.
3-4) Over Current Protection Function (OCP)
The overcurrent protection function is realized by using the current mode control to limit the current that flows through
the high-side MOSFET at each cycle of the switching frequency.
3-5) Over Voltage Protection Function (OVP)
Over voltage protection function (OVP) compares FB terminal voltage with internal standard voltage VREF and when FB
terminal voltage exceeds1.04V (typ) it turns MOSFET of output part MOSFET OFF. After output voltage drop it returns
with hysteresis.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
19/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Application Example
Figure 48. Application Circuit
Table 2. Recommendation Circuit constants
VIN
VOUT
CIN
CBOOT
L
R1
R2
R3
C1
C2
COUT
12V
10μF
0.1μF
6.8μH
430kΩ
82kΩ
91kΩ
680pF
5V
10μF
0.1μF
6.8μH
430kΩ
82kΩ
82kΩ
13pF
360pF
Ceramic
22μF×3
Ceramic
10μF×3
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
10μF
0.1μF
6.8μH
430kΩ
82kΩ
51kΩ
10pF
100pF
Ceramic 10μF
and
Aluminum
100μF
20/29
10μF
0.1μF
6.8μH
470kΩ
150kΩ
68kΩ
1200pF
Ceramic
22μF×3
3.3V
10μF
0.1μF
6.8μH
470kΩ
150kΩ
56kΩ
13pF
470pF
Ceramic
10μF×3
10μF
0.1μF
6.8μH
470kΩ
150kΩ
43kΩ
10pF
160pF
Ceramic 10μF
and
Aluminum
100μF
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Selection of Components Externally Connected
1) Output LC Filter
The DC/DC converter requires an LC filter for smoothing the output voltage in order to supply a continuous current to the
load. BD9E102FJ is returned to the IC and IL ripple current flowing through the inductor for SLLMTM control. This feedback
current, Inductance value is the behavior of the best when the 6.8µH. Therefore, the inductor to use is recommended
6.8µH.
VIN
IL
Inductor saturation current > IOUTMAX +⊿IL /2
L
VOUT
Driver
IOUTMAX
⊿IL
COUT
Average inductor current
Figure 49. Waveform of current through inductor
Figure 50. Output LC filter circuit
Computation with VIN = 12V, VOUT = 5V, L=6.8µH, switching frequency FOSC= 570kHz, the method is as below.
Inductor ripple current
⊿IL =
VOUT (VIN - VOUT)
1
VIN FOSC L
= 752 mA
Also for saturation current of inductor, select the one with larger current than maximum output current added by 1/2 of
inductor ripple current ∆IL.
Output capacitor COUT affects output ripple voltage characteristics. Select output capacitor COUT so that necessary ripple
voltage characteristics are satisfied.
Output ripple voltage can be expressed in the following method.
1
∆VRPL = ⊿IL ( RESR +
)V
8 COUT FOSC
RESR is the serial equivalent series resistance here.
With COUT = 66µF, RESR = 10mΩ the output ripple voltage is calculated as
∆VRPL = 0.75 (10m + 1 / (8 66µ 570k)) = 10mV
*Be careful of total capacitance value, when additional capacitor CLOAD is connected in addition to output capacitor COUT.
Use maximum additional capacitor CLOAD(max.) condition which satisfies the following method.
Maximum starting inductor ripple current ILSTART
<
Over Current limit 1.9A (min.)
Maximum starting inductor ripple current ILSTART can be expressed in the following method.
ILSTART =
Maximum starting output current (IOMAX) +
Charge current to output capacitor(ICAP) +
⊿IL
2
Charge current to output capacitor ICAP can be expressed in the following method.
ICAP =
( COUT + CLOAD ) VOUT
TSS
A
Computation with VIN = 12V, VOUT = 5V, L = 6.8µH, IOMAX = 1A (max.), switching frequency FOSC= 484kHz (min.), Output
capacitor COUT = 66µF, Soft Start time TSS = 1.2ms (min.), the method is as below.
( 1.9 – IOMAX – ⊿IL / 2 ) × TSS
CLOAD (max.) <
– COUT
= 43.6µF
VOUT
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
21/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
2) Output Voltage Set Point
The output voltage value can be set by the feedback resistance ratio.
VOUT
VOUT =
R1
FB
R2
－
R1 + R2
R2
0.8 V
ERR
＋
※
0.8V
Figure 51. Feedback resister circuit
Minimum pulse range that output can output stably
through all the load area is 250nsec for BD9E102FJ.
Use input/output condition which satisfies the following
method.
VOUT
250 nsec ≤
1.75 µsec
VIN
3) Phase Compensation
A current mode control buck DC/DC converter is a two-pole, one-zero system: two poles formed by an error amplifier and
load and one zero point added by phase compensation. The phase compensation resistor RCMP determines the crossover
frequency FCRS where the total loop gain of the DC/DC converter is 0 dB. Specifying a high value for this crossover
frequency FCRS provides a good load transient response characteristic but inferior stability. Conversely, specifying a low
value for the crossover frequency FCRS greatly stabilizes the characteristics but the load transient response characteristic
is impaired.
3-1) Selection of Phase Compensation Resistor RCMP
The phase compensation resistance RCMP can be determined by using the following equation.
2 x VOUT x FCRS x COUT
RCMP =
VFB x GMP x GMA
VOUT: output voltage
FCRS: crossover frequency
COUT: output capacitanceor
VFB: feedback reference voltage (0.8 V (typ.))
GMP: current sense gain (7 A/V (typ.))
GMA: error amplifier transconductance (82 µA/V (typ.))
3-2) Selection of phase compensation capacitance CCMP
For stable operation of the DC/DC converter, inserting a zero point at 1/6 of the zero crossover frequency that cancels
the phase delay due to the pole formed by the load often provides favorable characteristics.
The phase compensation capacitance CCMP can be determined by using the following equation.
1
2 x RCMP X FZ
CCMP=
F
Fz: Zero point inserted
3-3) Loop stability
To ensure the stability of the DC/DC converter, use the actual device to make sure that a sufficient phase margin is
provided. Ensuring a phase margin of at least 45 degrees in the worst conditions is recommended. The feed forward
capacitor CRUP is used for the purpose of forming a zero point together with the resistor RUP to increase the phase
margin within the limited frequency range. Using a CRUP is effective when the RUP resistance is larger than the
combined parallel resistance of RUP and RDW.
VOUT
A
(a)
Gain [dB]
RUP
CRUP
FB
GBW(b)
0
COMP
Phase[deg]
RDW
0.8V
CCMP
－90
RCMP
－180
f
FCR S
0
－90°
PHASE MARGIN
－180°
f
Figure 52. Phase compensation circuit
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
Figure 53. Bode plot
22/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
PCB Layout Design
In the buck DC/DC converter, a large pulsed current flows in two loops. The first loop is the one into which the current flows
when the High Side FET is turned on. The flow starts from the input capacitor CIN, runs through the FET, inductor L and
output capacitor COUT and back to ground of CIN via ground of COUT. The second loop is the one into which the current flows
when the Low Side FET is turned on. The flow starts from the Low Side FET, runs through the inductor L and output
capacitor COUT and back to ground of the Low Side FET via ground of COUT. Tracing these two loops as thick and short as
possible allows noise to be reduced for improved efficiency. It is recommended to connect the input and output capacitors,
in particular, to the ground plane. The PCB layout has a great influence on the DC/DC converter in terms of all of the heat
generation, noise and efficiency characteristics.
Figure 54. Current loop of buck converter
Accordingly, design the PCB layout with particular attention paid to the following points.
Provide the input capacitor as close to the IC VIN terminal as possible on the same plane as the IC.
If there is any unused area on the PCB, provide a copper foil plane for the ground node to assist heat dissipation from
the IC and the surrounding components.
Switching nodes such as SW are susceptible to noise due to AC coupling with other nodes. Trace to the coil as thick
and as short as possible.
Provide lines connected to FB and COMP as far away from the SW node.
Provide the output capacitor away from the input capacitor in order to avoid the effect of harmonic noise from the
input.
COUT
VOUT
GND
L
CIN
CBOOT
SW
R1
C2
VIN
R2
R3
EN
Top Layer
Bottom Layer
Figure 55. Example of sample board layout pattern
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
23/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Power Dissipation
When designing the PCB layout and peripheral circuitry, sufficient consideration must be given to ensure that the power
dissipation is within the allowable dissipation curve.
0.8
Power dissipation: Pd [W]
0.675W
0.6
θj-a=185.2℃/W
1 layer board
（back side copper foil area:70mm×70mm）
0.4
0.2
0
0
25
50
75 85 100
125
150
Temperature:Ta [℃]
Figure 56. Power dissipation (SOP-J8)
I/O Equivalence Circuit
1. BOOT
8. SW
3. EN
BOOTREG
BOOT
VIN
SW
REG
PGND
5. FB
6. COMP
FB
AGND
Figure 57. I/O equivalence circuit
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
24/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Operational Notes
1) Absolute Maximum Ratings
While abundant attention is paid to quality management of this IC, use of the IC in excess of absolute maximum ratings
such as the applied voltage and operating temperature range may result in deterioration or damage. For design, ensure
that it is always used within the guaranteed range. Use of the IC in excess of absolute maximum ratings such as the
applied voltage and operating temperature range may result in damage. The state of the IC (short mode, open mode, etc.)
cannot be identified if such damage occurs. Physical safety measures such as provision of a fuse should be taken when a
special mode in which the absolute maximum ratings may be exceeded is anticipated.
2) GND Potential
Ensure the minimum GND pin potential in all operating conditions.
3) Thermal Design
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions.
4) Pin Short and Faulty Mounting
Use caution when orienting and positioning the IC for mounting on printed circuit boards. Improper mounting may result in
damage to the IC. Avoid short-circuiting between VIN and VOUT/SW. Short-circuiting between these may result in
damage to the IC and smoke generation. In a case that has been applied VIN = 20V or more, when there is a possibility
the BOOT terminal and SW terminal is short-circuited, please insert a resistance of about 10 ohms between the bootstrap
capacitor 0.1µF and BOOT terminal. Short-circuiting between these without inserting this resistance may result in damage
to the IC and smoke generation.
5) Actions is Strong Magnetic Field
Use caution when using the IC in the presence of a strong magnetic field as doing so may cause the IC to malfunction.
6) Testing on Application Boards
When testing the IC on an application board, connecting a capacitor to a pin with a low impedance may subject the IC to
stress. Always discharge capacitors after each process. Always turn the power supply off before connecting it to or
removing it from a jig or fixture during the inspection process. As an antistatic measure, ground the IC during assembly
steps and use similar caution when transporting or storage the IC.
7) PCB Layout
Be sure to connect VIN to the power supply on the board.
Be sure to connect PGND and AGND to the GND on the board.
Ensure that the VIN wiring is thick and short for a sufficiently low impedance.
Ensure that the PGND and AGND wiring is thick and short for a sufficiently low impedance.
Take the output voltage of the DC/DC converter from the two ends of the output capacitor.
The PCB layout and peripheral components may influence the performance of the DC/DC converter. Give sufficient
consideration to the design of the peripheral circuitry.
8) IC Pin Input
This IC is a monolithic IC and, between each element, it has P+ isolation for element separation and P substrate. With this P
layer and the N layer of the respective elements, P-N junctions are formed to constitute a variety of parasitic elements. For
example, when a resistor and transistor are connected to terminals as shown in the figure below, reversal of the terminal voltage
and GND voltage activates the parasitic diode and transistor.
Parasitic elements are inevitably generated by the potential relationship due to the IC structure. Activation of a parasitic
element may cause interference in circuit operation, possibly leading to damage. Accordingly, use abundance of caution
to avoid use that causes the parasitic elements to operate such as applying a voltage that is lower than the GND (P
substrate) to an I/O terminal.
Resistor
Transistor (NPN)
B
～
～
E
B
～
～
C
(Pin B)
(Pin B)
～
～
(Pin A)
GND
P+
P+
N
N
P
N
N
N
GND
Parasitic
elements
P+
N
(Pin A)
P substrate
Parasitic elements
GND
P
Parasitic elements
E
～
～
N
P
P+
C
Parasitic
elements
GND
GND
Figure 58. Example of simplified structure of monolithic IC
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
25/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
9) Overcurrent protection Circuit
The DC/DC converter output terminal integrates an overcurrent protection function, which is effective in protecting the IC from
damage caused by unexpected GND short circuit. Avoid use on the premise of continuous operation of the protection circuit.
10) Thermal Shutdown Circuit
If the chip temperature reaches Tj = 175°C (typ.), the thermal shutdown function is activated and the DC/DC converter stops
switching.
The thermal shutdown circuit is intended for shutting down the IC from thermal runaway and is not meant to protect or
guarantee the soundness of the application. Accordingly, avoid use on the premise of continuous use or operation after the
activation of this circuit.
11) Enable Function
If the rate of fall of the EN terminal signal is too low, chattering may occur. Chattering with the output voltage remaining may
generate a reverse current that boosts the voltage from the output to the input, possibly leading to damage. For on/off control
with the EN signal, ensure that the signal falls within 100 µsec.
12) Load at Startup
Ensure that the respective output has light load at startup of this IC.
Restrain the power supply line noise at startup and voltage drop generated by operating current within the hysteresis width of
UVLO. Input of any noise exceeding the hysteresis noise width may cause malfunction.
13) External Elements
Use a ceramic capacitor with a low ESR for the bypass capacitor between VIN and PGND and provide it as close to the IC
as possible. For external components such as inductors and capacitors, use theose recommended in this specification
and provide as close to the IC as possible. For those through which large current flows, in particular, ensure that the wiring
is thick and short.
14) IC Applications
This IC is not developed for in-vehicle or military applications or equipment/devices that may affect human lives. Do not use the
IC for such applications. If this IC is used by customers in any of such applications as described above, ROHM shall not be held
responsible for failure to satisfy the requirements concerned.
15) Use Environment
The operating temperature range is intended to guarantee functional operation and does not guarantee the life of the IC within
this range. The life of the IC may be subject to derating depending on use environment such as the voltage applied, ambient
temperature and humidity. Design equipment and devices in view of derating.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
26/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
Ordering Information
B
D
9
E
1
Part Number
0
2
F
J
Package
FJ: SOP-J8
-
E2
Packaging and forming specification
E2: Embossed tape and reel
Marking Diagram
SOP-J8(TOP VIEW)
Part Number Marking
9 E 1 0 2
LOT Number
1PIN MARK
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
27/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
●Physical Dimension, Tape and Reel Information – continued
Package Name
SOP-J8
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
Direction of feed
1pin
Reel
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
)
∗ Order quantity needs to be multiple of the minimum quantity.
28/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
BD9E102FJ
●Revision History
Date
Revision
1. May. ’13
001
Description
Created
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ22111•15•001
29/29
TSZ02201-0J3J0AJ00500-1-2
1.MAY.2013 Rev.001
Datasheet
Notice
Precaution on using ROHM Products
1.
Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
(Note 1)
, transport
intend to use our Products in devices requiring extremely high reliability (such as medical equipment
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅣ
CLASSⅢ
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2.
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice - GE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.002
Datasheet
Precautions Regarding Application Examples and External Circuits
1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights
1.
All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Other Precaution
1.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4.
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - GE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.002
Datasheet
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3.
The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or
concerning such information.
Notice – WE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.001
工商网监
湘ICP备2023018690号
