UMD3NFHATR

EMD3FHA / UMD3NFHA / IMD3AFRA EMD3 / UMD3N / IMD3A NPN + PNP Complex Digital Transistors (Bias Resistor Built-in Transistors) Datasheet AEC-Q101 Qualified lOutline Parameter VCC IC(MAX.) R1 R2 Value EMT6 50V 100mA 10kW 10kW (6) (1) (2) (5) (4) (3) VCC -50V -100mA 10kW 10kW IC(MAX.) R1 R2 (1) EMD3 EMD3FHA (SC-107C) Value (4) (2) (3) SMT6 Parameter (6) UMT6 (2) (5) (5) (4) (3) UMD3NFHA UMD3N SOT-363 (SC-88) (6) (1) IMD3AFRA IMD3A SOT-457 (SC-74) lInner circuit lFeatures 1) Both the DTC114E chip and DTA114E chip in one package. 2) Built-in bias resistors enable the configuration of an inverter circuit without connecting external input resistors (see inner circuit). 3) The bias resistors consist of thin-film resistors with complete isolation to allow negative biasing of the input. They also have the advantage of completely eliminating parasitic effects. 4) Only the on/off conditions need to be set for operation, making the circuit design easy. 5) Lead Free/RoHS Compliant. OUT (6) DTr1 IN (5) R1 GND (4) R2 R2 R1 (1) GND (2) IN DTr2 (3) OUT EMD3FHA EMD3 //UMD3NFHA UMD3N IN (5) OUT (4) R1 DTr2 lApplication R2 GND (6) R2 R1 DTr1 Inverter circuit, Interface circuit, Driver circuit (3) GND (2) IN (1) OUT IMD3AFRA IMD3A lPackaging specifications Basic Reel size Tape width ordering (mm) (mm) unit (pcs) Package Package size (mm) Taping code EMD3 EMD3FHA EMT6 1616 T2R 180 8 8,000 D3 UMD3N UMD3NFHA UMT6 2021 TR 180 8 3,000 D3 IMD3AFRA IMD3A SMT6 2928 T108 180 8 3,000 D3 Part No. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 1/8 Marking 2013.07 - Rev.E EMD3FHA / UMD3NFHA EMD3 / UMD3N / IMD3A / IMD3AFRA Data Sheet lAbsolute maximum ratings (Ta = 25C) Parameter Symbol DTr1(NPN) DTr2(PNP) Unit Supply voltage VCC 50 -50 V Input voltage VIN -10 to +40 -40 to +10 V Output current IO 50 -50 mA IC(MAX.)*1 100 -100 mA Collector current Power dissipation EMD3FHA / UMD3NFHA EMD3 / UMD3N PD *2 IMD3A IMD3AFRA mW *4 mW 300 (Total) Tj 150 °C Tstg -55 to +150 °C Junction temperature Range of storage temperature 150 (Total)*3 lElectrical characteristics(Ta = 25°C) Parameter Symbol Conditions Min. Typ. Max. Unit VI(off) VCC = 5V, IO = 100mA - - 0.5 VI(on) VO = 0.3V, IO = 10mA 3.0 - - VO(on) IO / II = 10mA / 0.5mA - 0.1 0.3 V VI = 5V - - 0.88 mA IO(off) VCC = 50V, VI = 0V - - 0.5 mA DC current gain GI VO = 5V, IO = 5mA 30 - - - Input resistance R1 - 7 10 13 kW Resistance ratio R2/R1 - 0.8 1 1.2 - VCE = 10V, IE = -5mA f = 100MHz - 250 - MHz Unit Input voltage Output voltage Input current Output current Transition frequency II fT *1 V lElectrical characteristics(Ta = 25°C) Symbol Conditions Min. Typ. Max. VI(off) VCC = -5V, IO = -100mA - - -0.5 VI(on) VO = -0.3V, IO = -10mA -3.0 - - VO(on) IO / II = -10mA / -0.5mA - -0.1 -0.3 V VI = -5V - - -0.88 mA IO(off) VCC = -50V, VI = 0V - - -0.5 mA DC current gain GI VO = -5V, IO = -5mA 30 - - - Input resistance R1 - 7 10 13 kW Resistance ratio R2/R1 - 0.8 1 1.2 - fT *1 VCE = -10V, IE = 5mA f = 100MHz - 250 - MHz Parameter Input voltage Output voltage Input current Output current Transition frequency II V *1 Characteristics of built-in transistor *2 Each terminal mounted on a reference footprint *3 120mW per element must not be exceeded. *4 200mW per element must not be exceeded. www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 2/8 2013.07 - Rev.E EMD3FHA / UMD3NFHA EMD3 / UMD3N / IMD3A / IMD3AFRA Data Sheet lElectrical characteristic curves (Ta = 25°C) Fig.2 Output current vs. input voltage (OFF characteristics) INPUT VOLTAGE : VI(on) [V] OUTPUT CURRENT : IO [A] Fig.1 Input voltage vs. output current (ON characteristics) OUTPUT CURRENT : IO [A] INPUT VOLTAGE : VI(off)[V] Fig.3 Output current vs. output voltage Fig.4 DC current gain vs. output current II= 260mA 240mA 220mA 40 200mA 180mA 30 160mA 20 140mA 120mA 10 0 Ta=25ºC DC CURRENT GAIN : GI OUTPUT CURRENT : IO [mA] 50 100mA 0A 0 5 10 OUTPUT CURRENT : IO [A] OUTPUT VOLTAGE : VO [V] www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 3/8 2013.07 - Rev.E EMD3FHA / UMD3NFHA EMD3 / UMD3N / IMD3A / IMD3AFRA Data Sheet lElectrical characteristic curves (Ta = 25°C) OUTPUT VOLTAGE : VO(on) [V] Fig.5 Output voltage vs. output current OUTPUT CURRENT : IO [A] lElectrical characteristic curves (Ta = 25°C) Fig.7 Output current vs. input voltage (OFF characteristics) INPUT VOLTAGE : VI(on) [V] OUTPUT CURRENT : IO [A] Fig.6 Input voltage vs. output current (ON characteristics) OUTPUT CURRENT : IO [A] www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. INPUT VOLTAGE : VI(off)[V] 4/8 2013.07 - Rev.E EMD3FHA / UMD3NFHA EMD3 / UMD3N / IMD3A / IMD3AFRA Data Sheet lElectrical characteristic curves (Ta = 25°C) Fig.9 DC current gain vs. output current Fig.8 Output current vs. output voltage -50 II= -300mA -40 -280mA -260mA -240mA -30 -220mA -200mA -180mA -20 -160mA -140mA -120mA -10 DC CURRENT GAIN : GI OUTPUT CURRENT : IO [mA] Ta=25ºC -100mA 0 0A 0 -5 -10 OUTPUT CURRENT : IO [A] OUTPUT VOLTAGE : VO [V] OUTPUT VOLTAGE : VO(on) [V] Fig.10 Output voltage vs. output current OUTPUT CURRENT : IO [A] www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 5/8 2013.07 - Rev.E EMD3FHA / UMD3NFHA EMD3 / UMD3N / IMD3A / IMD3AFRA Data Sheet lDimensions (Unit : mm) 㻰 㼎 㼤 㼏 㻿 㻭 㻸㼜 㻸㼜 㻴㻱 㻸 㻱 㻸 EMT6 㻭 㻭㻝 㼥 㻿 㼘㻝 㻭 㼑㻝 㼑 㻿 㼎㻞 㼑 Pattern of terminal position areas [Not a recommended pattern of soldering pads] 㻰㻵㻹 㻭 㻭㻝 㼎 㼏 㻰 㻱 㼑 㻴㻱 㻸 㻸㼜 㼤 㼥 㻰㻵㻹 㼎㻞 㼑㻝 㼘㻝 㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿 㻹㻵㻺 㻹㻭㼄 㻜㻚㻠㻡 㻜㻚㻡㻡 㻜㻚㻜㻜 㻜㻚㻝㻜 㻜㻚㻝㻣 㻜㻚㻞㻣 㻜㻚㻜㻤 㻜㻚㻝㻤 㻝㻚㻡㻜 㻝㻚㻣㻜 㻝㻚㻝㻜 㻝㻚㻟㻜 㻜㻚㻡㻜 㻝㻚㻡㻜 㻝㻚㻣㻜 㻜㻚㻝㻜 㻜㻚㻟㻜 㻙 㻜㻚㻟㻡 㻙 㻜㻚㻝㻜 㻙 㻜㻚㻝㻜 㻵㻺㻯㻴㻱㻿 㻹㻵㻺 㻜㻚㻜㻝㻤 㻜㻚㻜㻜㻜 㻜㻚㻜㻜㻣 㻜㻚㻜㻜㻟 㻜㻚㻜㻡㻥 㻜㻚㻜㻠㻟 㻹㻭㼄 㻜㻚㻜㻞㻞 㻜㻚㻜㻜㻠 㻜㻚㻜㻝㻝 㻜㻚㻜㻜㻣 㻜㻚㻜㻢㻣 㻜㻚㻜㻡㻝 㻜㻚㻜㻞㻜 㻜㻚㻜㻡㻥 㻜㻚㻜㻜㻠 㻙 㻙 㻙 㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿 㻹㻵㻺 㻹㻭㼄 㻙 㻜㻚㻟㻣 㻝㻚㻞㻡 㻙 㻜㻚㻠㻡 㻜㻚㻜㻢㻣 㻜㻚㻜㻝㻞 㻜㻚㻜㻝㻠 㻜㻚㻜㻜㻠 㻜㻚㻜㻜㻠 㻵㻺㻯㻴㻱㻿 㻹㻵㻺 㻙 㻹㻭㼄 㻜㻚㻜㻝㻡 㻜㻚㻜㻠㻥 㻙 㻜㻚㻜㻝㻤 Dimension in mm / inches www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 6/8 2013.07 - Rev.E EMD3FHA / UMD3NFHA EMD3 / UMD3N / IMD3A / IMD3AFRA Data Sheet lDimensions (Unit : mm) 㻰 㻭 㼑 㼏 㼤 㻸㼜 㻭㻟 㻿 㻭 㼑 㼑㻝 㼘㻝 㼥 㻿 㻭㻝 㻭 㼎 㻴㻱 㻱 㻽 㻸㻝 UMT6 㻿 㼎㻞 Pattern of terminal position areas [Not a recommended pattern of soldering pads] 㻰㻵㻹 㻭 㻭㻝 㻭㻟 㼎 㼏 㻰 㻱 㼑 㻴㻱 㻸㻝 㻸㼜 㻽 㼤 㼥 㻰㻵㻹 㼎㻞 㼑㻝 㼘㻝 㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿 㻹㻵㻺 㻹㻭㼄 㻜㻚㻤㻜 㻝㻚㻜㻜 㻜㻚㻜㻜 㻜㻚㻝㻜 㻜㻚㻞㻡 㻜㻚㻝㻡 㻜㻚㻟㻜 㻜㻚㻝㻜 㻜㻚㻞㻜 㻝㻚㻥㻜 㻞㻚㻝㻜 㻝㻚㻝㻡 㻝㻚㻟㻡 㻜㻚㻢㻡 㻞㻚㻜㻜 㻞㻚㻞㻜 㻜㻚㻞㻜 㻜㻚㻡㻜 㻜㻚㻞㻡 㻜㻚㻡㻡 㻜㻚㻝㻜 㻜㻚㻟㻜 㻙 㻜㻚㻝㻜 㻙 㻜㻚㻝㻜 㻵㻺㻯㻴㻱㻿 㻹㻵㻺 㻜㻚㻜㻟㻝 㻜㻚㻜㻜㻜 㻹㻭㼄 㻜㻚㻜㻟㻥 㻜㻚㻜㻜㻠 㻜㻚㻜㻝㻜 㻜㻚㻜㻜㻢 㻜㻚㻜㻜㻠 㻜㻚㻜㻣㻡 㻜㻚㻜㻠㻡 㻜㻚㻜㻝㻞 㻜㻚㻜㻜㻤 㻜㻚㻜㻤㻟 㻜㻚㻜㻡㻟 㻜㻚㻜㻞㻢 㻜㻚㻜㻣㻥 㻜㻚㻜㻜㻤 㻜㻚㻜㻝㻜 㻜㻚㻜㻜㻠 㻙 㻙 㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿 㻹㻵㻺 㻹㻭㼄 㻙 㻜㻚㻠㻜 㻝㻚㻡㻡 㻙 㻜㻚㻢㻡 㻜㻚㻜㻤㻣 㻜㻚㻜㻞㻜 㻜㻚㻜㻞㻞 㻜㻚㻜㻝㻞 㻜㻚㻜㻜㻠 㻜㻚㻜㻜㻠 㻵㻺㻯㻴㻱㻿 㻹㻵㻺 㻙 㻹㻭㼄 㻜㻚㻜㻝㻢 㻜㻚㻜㻢㻝 㻙 㻜㻚㻜㻞㻢 Dimension in mm / inches www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 7/8 2013.07 - Rev.E EMD3FHA / UMD3NFHA EMD3 / UMD3N / IMD3A / IMD3AFRA Data Sheet lDimensions (Unit : mm) 㻰 㻭 㼑 SMT6 㼏 㻸㻝 㻸㼜 㻴㻱 㻱 㻽 㻭㻟 㼎 㼤 㻿 㻭 㼘㻝 㻭 㼑㻝 㼑 㻭㻝 㼥 㻿 㻿 㼎㻞 Pattern of terminal position areas [Not a recommended pattern of soldering pads] 㻰㻵㻹 㻭 㻭㻝 㻭㻟 㼎 㼏 㻰 㻱 㼑 㻴㻱 㻸㻝 㻸㼜 㻽 㼤 㼥 㻰㻵㻹 㼎㻞 㼑㻝 㼘㻝 㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿 㻹㻵㻺 㻹㻭㼄 㻝㻚㻜㻜 㻝㻚㻟㻜 㻜㻚㻜㻜 㻜㻚㻝㻜 㻜㻚㻞㻡 㻜㻚㻞㻡 㻜㻚㻠㻜 㻜㻚㻜㻥 㻜㻚㻞㻡 㻞㻚㻤㻜 㻟㻚㻜㻜 㻝㻚㻡㻜 㻝㻚㻤㻜 㻜㻚㻥㻡 㻞㻚㻢㻜 㻟㻚㻜㻜 㻜㻚㻟㻜 㻜㻚㻢㻜 㻜㻚㻠㻜 㻜㻚㻣㻜 㻜㻚㻞㻜 㻜㻚㻟㻜 㻙 㻜㻚㻞㻜 㻙 㻜㻚㻝㻜 㻵㻺㻯㻴㻱㻿 㻹㻵㻺 㻜㻚㻜㻟㻥 㻜㻚㻜㻜㻜 㻹㻭㼄 㻜㻚㻜㻡㻝 㻜㻚㻜㻜㻠 㻜㻚㻜㻝㻜 㻜㻚㻜㻝㻜 㻜㻚㻜㻜㻠 㻜㻚㻝㻝㻜 㻜㻚㻜㻡㻥 㻜㻚㻜㻝㻢 㻜㻚㻜㻝㻜 㻜㻚㻝㻝㻤 㻜㻚㻜㻣㻝 㻜㻚㻜㻟㻣 㻜㻚㻝㻜㻞 㻜㻚㻜㻝㻞 㻜㻚㻜㻝㻢 㻜㻚㻜㻜㻤 㻙 㻙 㻹㻵㻸㻵㻹㻱㼀㻱㻾㻿 㻹㻵㻺 㻹㻭㼄 㻜㻚㻢㻜 㻞㻚㻝㻜 㻙 㻜㻚㻥㻜 㻜㻚㻝㻝㻤 㻜㻚㻜㻞㻠 㻜㻚㻜㻞㻤 㻜㻚㻜㻝㻞 㻜㻚㻜㻜㻤 㻜㻚㻜㻜㻠 㻵㻺㻯㻴㻱㻿 㻹㻵㻺 㻙 㻹㻭㼄 㻜㻚㻜㻞㻠 㻜㻚㻜㻤㻟 㻙 㻜㻚㻜㻟㻡 Dimension in mm / inches www.rohm.com © 2013 ROHM Co., Ltd. All rights reserved. 8/8 2013.07 - Rev.E Datasheet Notice Precaution on using ROHM Products 1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PAA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PAA-E © 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice – WE © 2015 ROHM Co., Ltd. All rights reserved. Rev.001