6EP33116SB000AY0

Data sheet 6EP3311-6SB00-0AY0 LOGO!Power/1AC/5VDC/6.3A LOGO!Power 5 V / 6.3 A stabilized power supply input: 100-240 V AC output: 5 V DC / 6.3 A *Ex approval no longer available* Input type of the power supply network 1-phase AC or DC supply voltage at AC ● minimum rated value 100 V ● maximum rated value 240 V ● initial value 85 V ● full-scale value 264 V input voltage ● at DC 110 ... 300 V design of input wide range input Yes overvoltage overload capability 300 V AC for 1 s operating condition of the mains buffering at Vin = 187 V buffering time for rated value of the output current in the event of power failure minimum 40 ms operating condition of the mains buffering at Vin = 187 V line frequency ● 1 rated value 50 Hz ● 2 rated value 60 Hz line frequency 47 ... 63 Hz input current ● at rated input voltage 120 V 0.71 A ● at rated input voltage 230 V 0.37 A current limitation of inrush current at 25 °C maximum 50 A I2t value maximum 3 A²·s fuse protection type internal ● in the feeder Recommended miniature circuit breaker: from 10 A characteristic B or from 6 A characteristic C Output voltage curve at output Controlled, isolated DC voltage output voltage at DC rated value 5V output voltage ● at output 1 at DC rated value 5V relative overall tolerance of the voltage 3% relative control precision of the output voltage ● on slow fluctuation of input voltage 0.1 % ● on slow fluctuation of ohm loading 0.1 % residual ripple ● maximum 100 mV ● typical 30 mV voltage peak 6EP33116SB000AY0 Page 1/3 7/5/2022 Subject to change without notice © Copyright Siemens ● maximum 100 mV ● typical 50 mV adjustable output voltage 4.6 ... 5.4 V product function output voltage adjustable Yes type of output voltage setting via potentiometer display version for normal operation Green LED for output voltage OK behavior of the output voltage when switching on No overshoot of Vout (soft start) response delay maximum 0.5 s voltage increase time of the output voltage ● typical 100 ms output current ● rated value 6.3 A ● rated range 0 ... 6.3 A; +55 ... +70 °C: Derating 2%/K supplied active power typical 31.5 W product feature ● bridging of equipment number of parallel-switched equipment resources for increasing the power Yes 2 Efficiency efficiency in percent 80 % power loss [W] ● at rated output voltage for rated value of the output current typical 8W ● during no-load operation maximum 0.3 W Closed-loop control relative control precision of the output voltage with rapid fluctuation of the input voltage by +/- 15% typical 0.2 % relative control precision of the output voltage at load step of resistive load 10/90/10 % typical 7% setting time ● load step 10 to 90% typical 1 ms ● load step 90 to 10% typical 1 ms Protection and monitoring design of the overvoltage protection Yes, according to EN 60950-1 response value current limitation typical 8.2 A property of the output short-circuit proof Yes design of short-circuit protection Constant current characteristic enduring short circuit current RMS value ● maximum 8.2 A overcurrent overload capability in normal operation overload capability 150% Iout rated typ. 200 ms display version for overload and short circuit - measuring point for output current 50 mV =^ 6.3 A overcurrent overload capability when switching on 150% Iout rated typ. 200 ms Safety galvanic isolation between input and output Yes galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 operating resource protection class Class II (without protective conductor) protection class IP IP20 Approvals certificate of suitability ● CE marking Yes ● UL approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus-Recognized (UL 60950, CSA C22.2 No. 60950), File E151273 ● CSA approval Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus-Recognized (UL 60950, CSA C22.2 No. 60950), File E151273 ● cCSAus, Class 1, Division 2 No ● ATEX No certificate of suitability ● IECEx No ● NEC Class 2 No ● ULhazloc approval No 6EP33116SB000AY0 Page 2/3 7/5/2022 Subject to change without notice © Copyright Siemens ● FM registration type of certification CB-certificate No Yes certificate of suitability ● EAC approval Yes certificate of suitability shipbuilding approval Yes shipbuilding approval ABS, BV, DNV GL, LRS Marine classification association ● American Bureau of Shipping Europe Ltd. (ABS) Yes ● French marine classification society (BV) Yes ● DNV GL Yes ● Lloyds Register of Shipping (LRS) Yes ● Nippon Kaiji Kyokai (NK) No EMC standard ● for emitted interference EN 55022 Class B ● for mains harmonics limitation not applicable ● for interference immunity EN 61000-6-2 environmental conditions ambient temperature ● during operation -25 ... +70 °C; with natural convection ● during transport -40 ... +85 °C ● during storage -40 ... +85 °C environmental category according to IEC 60721 Climate class 3K3, 5 … 95% no condensation Mechanics type of electrical connection screw-type terminals ● at input L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded ● at output +, -: 1 screw terminal each for 0.5 ... 2.5 mm² ● for auxiliary contacts - width of the enclosure 54 mm height of the enclosure 90 mm depth of the enclosure 53 mm required spacing ● top 20 mm ● bottom 20 mm ● left 0 mm ● right 0 mm net weight 0.2 kg product feature of the enclosure housing can be lined up Yes fastening method Snaps onto DIN rail EN 60715 35x7.5/15, direct mounting in different mounting positions MTBF at 40 °C 2 654 280 h other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) 6EP33116SB000AY0 Page 3/3 7/5/2022 Subject to change without notice © Copyright Siemens