ESDA14V2LY

ESDALY Automotive dual Transil™ array for ESD protection Datasheet - production data Applications Where transient overvoltage protection in ESD sensitive equipment is required, such as:     Description SOT23-3L This device is a diode array designed to protect 1 line or 2 lines against ESD transients. The device is ideal for applications where both reduced line capacitance and board space saving are required Features     Entertainment Signal communications Connectivity Comfort and convenience AEC-Q101 qualified Dual unidirectional Transil functions Low leakage current: IR max. < 20 µA at VBR 300 W peak pulse power (8/20 µs) It can also be used as bidirectional suppressor by connecting only pin 1 and 2. Figure 1: Functional diagram Benefits     High ESD protection level: up to 25 kV High integration Suitable for high density boards AEC-Q101 qualified 1 3 Complies with the following standards    ISO 10605: C = 330 pF, R = 330 Ω  30 kV (air discharge)  30 kV (contact discharge) ISO 7637-3 fast transient  Pulse a: VS = -150 V  Pulse b: VS = +100 V ISO 7637-3 slow transient  Positive pulse: VS = +85 V  Negative pulse : VS = -85 V July 2017 2 DocID022075 Rev 2 This is information on a product in full production. 1/12 www.st.com Characteristics 1 ESDALY Characteristics Table 1: Absolute maximum ratings (Tamb = 25 °C) Symbol Vpp Ppp Parameter Value ISO 10605 (C = 330 pF, R = 330 Ω): Contact discharge Air discharge ISO 10605 (C = 150 pF, R = 330 Ω): Contact discharge Air discharge Peak pulse voltage(1) Peak pulse power (8/20 μs) 30 30 Unit kV 30 30 300 W 25 18 14 7 6.3 A ESDA5V3LY ESDA6V1LY ESDA14V2LY ESDA25LY ESDA37LY Ipp Peak pulse current (8/20 μs) Tj Operating junction temperature range -40 to 150 °C Tstg Storage junction temperature range -65 to 150 °C TL Maximum temperature for soldering during 10 s 260 °C Notes: (1)For a surge greater than the maximum values, the diode will fail in short-circuit. Figure 2: Electrical characteristics (definitions) Symbol VBR VCL VRM IRM IF IPP IR VF C Rd αT 2/12 = = = = = = = = = = = Parameter Breakdown voltage Clamping voltage Stand-off voltage Leakage current Forward current Peak pulse current Breakdown current Forward voltage drop Capacitance Dynamic impedance Voltage temperature DocID022075 Rev 2 I IF VBR Vcl VF VRM IRM Slope = 1/Rd IPP V ESDALY Characteristics Table 2: Electrical characteristics (Tamb = 25 °C) VBR at IR Order code IRM at VRM Min. Max. Max. V V mA µA V Rd(1) αT(2) Cline VF at IF Typ. Max. Typ. at 0 V bias Max. mΩ 10-4/°C pF V mA ESDA5V3LY 5.3 5.9 1 2 3 280 5 220 1.25 200 ESDA6V1LY 6.1 7.2 1 20 5.25 350 6 140 1.25 200 ESDA14V2LY 14.2 15.8 1 5 12 650 11 90 1.25 200 ESDA25LY 25 30 1 1 24 1000 11 50 1.2 10 ESDA37LY 37 43.3 1 1 36 2400 11 48 0.9 10 Notes: (1)Square (2)∆ pulse Ipp = 15 A, tp = 2.5 µs VBR = αT x (Tamb -25 °C) x VBR (25 °C) DocID022075 Rev 2 3/12 Characteristics 1.1 ESDALY Characteristics (curves) Figure 3: Variation of peak pulse power versus initial junction temperature Figure 4: Peak pulse power versus exponential pulse duration PPP(W) PPP(W) 350 Tj initial = 25 °C maximum value 1000 300 250 200 150 100 100 50 Tj(°C) 0 25 50 75 100 125 ESDA5V3LY ESDA6V1LY ESDA14V2LY ESDA25LY 150 ESDA37LY 175 tp(µs) 10 10 Figure 5: Variation of clamping voltage versus peak pulse current (max. values, 8/20 µs waveform) 100 1000 Figure 6: Relative variation of leakage current at VR = VRM versus junction values IPP(A) Ir(nA) 100 Tj initial = 25 °C 8/20µs 10 10000 ESDA5V3LY ESDA6V1LY ESDA14V2LY ESDA25LY ESDA37LY 1000 100 10 1 1 ESDA5V3LY ESDA6V1L ESDA14V2LY ESDA25LY ESDA37LY 0.1 VCL(V) 0.1 0 4/12 10 20 30 40 50 Tj(°C) 0.01 60 DocID022075 Rev 2 25 50 75 100 125 150 ESDALY Characteristics Figure 7: ISO 7637-3 fast transient pulse a response (VS = -150 V) 0.5 V/div 500 mA/div Figure 8: ISO 7637-3 fast transient pulse b response (VS = +100 V) 10 V/div 50 ns/div 500 mA/div 50 ns/div 50 ns/div Figure 9: ISO 7637-3 slow transient positive pulse(VS = +85 V) 10 V/div 2 A/div 50 ns/div Figure 10: ISO 7637-3 slow transient negative pulse(VS = -85 V) 10 V/div 5 µs/div 5 A/div 5 µs/div DocID022075 Rev 2 5 µs/div 5 µs/div 5/12 Application and design guidelines 2 ESDALY Application and design guidelines Refer to STMicroelectronics application note:  6/12 AN2689: Protection of automotive electronics from electrical hazards, guidelines for design and component selection. DocID022075 Rev 2 Package information ESDALY 3 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.   3.1 Epoxy meets UL 94,V0 Lead-free package SOT23-3L mechanical data Figure 11: SOT23-3L package outline 005 3390_I DocID022075 Rev 2 7/12 Package information ESDALY Table 3: SOT23-3L mechanical data mm Dim. Min. Typ. Max. A 0.89 1.40 A1 0 0.10 B 0.30 0.51 C 0.085 0.18 D 2.75 3.04 e 0.85 1.05 e1 1.70 2.10 E 1.20 1.75 H 2.10 3.00 L 0.60 S 0.35 0.65 L1 0.25 0.55 a 0° 8° Figure 12: SOT23-3L recommended footprint 0.48 0.95 2.89 0.97 0.99 SOT-23 footp_I Dimensions are in mm. 8/12 DocID022075 Rev 2 Recommendation on PCB assembly ESDALY 4 Recommendation on PCB assembly 4.1 Solder paste 1. 2. 3. 4. 4.2 Placement 1. 2. 3. 4. 5. 6. 4.3 Halide-free flux qualification ROL0 according to ANSI/J-STD-004. “No clean” solder paste is recommended. Offers a high tack force to resist component movement during high speed. Use solder paste with fine particles: powder particle size 20-45 µm. Manual positioning is not recommended. It is recommended to use the lead recognition capabilities of the placement system, not the outline centering Standard tolerance of ±0.05 mm is recommended. 3.5 N placement force is recommended. Too much placement force can lead to squeezed out solder paste and cause solder joints to short. Too low placement force can lead to insufficient contact between package and solder paste that could cause open solder joints or badly centered packages. To improve the package placement accuracy, a bottom side optical control should be performed with a high resolution tool. For assembly, a perfect supporting of the PCB (all the more on flexible PCB) is recommended during solder paste printing, pick and place and reflow soldering by using optimized tools. PCB design preference 1. 2. To control the solder paste amount, the closed via is recommended instead of open vias. The position of tracks and open vias in the solder area should be well balanced. A symmetrical layout is recommended, to avoid any tilt phenomena caused by asymmetrical solder paste due to solder flow away. DocID022075 Rev 2 9/12 Recommendation on PCB assembly 4.4 ESDALY Reflow profile Figure 13: ST ECOPACK® recommended soldering reflow profile for PCB mounting Minimize air convection currents in the reflow oven to avoid component movement. 10/12 DocID022075 Rev 2 Ordering information ESDALY 5 Ordering information Figure 14: Ordering information scheme ESDA XXX LY ESD Array Minimum breakdown voltage Package L = SOT23-3L Y = Automotive grade Table 4: Ordering information Order code Marking(1) ESDA5V3LY EL5Y ESDA6V1LY EL6Y ESDA14V2LY EL1Y ESDA25LY EL2Y ESDA37LY EL3Y Package SOT23-3L Weight Base qty. Delivery mode 3000 Tape and reel 8.7 mg 9.8 mg Notes: (1)The 6 marking can be rotated by multiples of 90° to differentiate assembly location. Revision history Table 5: Document revision history Date Revision Changes 16-Feb-2012 1 Initial version. This document merges and updates the content of the datasheet ESDA25LY Revision 1, 01-Feb-2010. 20-Jul-2017 2 Added ESDA37LY package information. DocID022075 Rev 2 11/12 ESDALY IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2017 STMicroelectronics – All rights reserved 12/12 DocID022075 Rev 2