0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
LCP02-150B1RL

LCP02-150B1RL

  • 厂商:

    STMICROELECTRONICS(意法半导体)

  • 封装:

    SOIC8_208MIL

  • 描述:

    THYRISTOR 30A 8SOIC

  • 数据手册
  • 价格&库存
LCP02-150B1RL 数据手册
® LCP02-150B1 PROTECTION IC FOR RINGING SLICS A.S.D.™ FEATURES s s s s s s Protection IC recommended for ringing SLICs. Wide firing voltage range: from -110V to +95V. Low gate triggering current: IG = 5mA max. Peak pulse current: IPP = 30A (10/1000µs) . Holding current: IH = 150mA min. UL497B approved (file E136224) SO-8 WIDE MAIN APPLICATIONS s s s s s s s s s s Dual battery supply voltage SLICs - negative battery supply configuration - negative & positive battery supply configuration Central Office (CO) Private Branch Exchange (PBX) Digital Loop Carrier (DLC) Asymmetrical Digital Subscriber Line (ADSL G.Lite) Fiber in the Loop (FITL) Wireless Local Loop (WLL) Hybrid Fiber Coax (HFC) ISDN Terminal Adapter Cable modem FUNCTIONAL DIAGRAM TIP Gn Gp GND DESCRIPTION The LCP02-150B1 has been developed to protect SLICs operating on both negative and positive battery supplies, as well as on high voltage SLICs. It provides crowbar mode protection for both TIP and RING lines. The surge suppression is assumed for each wire by two thyristor structures, one dedicated to positive surges the second one for negative surges. Both positive and negative threshold levels are programmable by two gates (Gn and Gp). The use of transistors decreases the battery currents during surge suppression. The LCP02-150B1 has high Bellcore Core, ITU-T and FCC Part 68 lightning surge ratings, ensuring rugged performance in the field. In addition, it is also specified to assist a designer to comply with UL1950, IEC950 and CSA C22.2. It is UL 497B approved (file E136224), and has UL94-V0 resin approved TM: ASD is trademarks of STMicroelectronics. RING PIN-OUT CONFIGURATION TIP Gn GP RING NC GND GND NC September 2000 - Ed: 4A 1/8 LCP02-150B1 COMPLIES WITH FOLLOWING STANDARDS Peak surge voltage (V) ITU-T K20 ITU-T K21 VDE0433 VDE0878 IEC61000-4-5 FCC Part 68 lightning surge type A FCC Part 68 lightning surge type B BELLCORE GR-1089-CORE First level BELLCORE GR-1089-CORE Second level BELLCORE GR-1089-CORE Intrabuilding 4000 1000 4000 1500 2000 2000 level 3 level 4 1500 800 1000 2500 1000 5000 Voltage waveform (µs) 10/700 10/700 10/700 10/700 10/700 1.2/50 10/700 1.2/50 10/160 10/560 9/720 2/10 10/1000 2/10 Required Current Minimum serial peak current waveform resistor to meet (A) (µs) standard ( ) 100 25 100 37.5 50 50 50 100 200 100 25 500 100 500 5/310 5/310 5/310 5/310 5/310 1/20 5/310 8/20 10/160 10/560 5/320 2/10 10/1000 2/10 50 0 50 0 5 0 5 25 20 15 0 20 25 40 800 1500 2/10 2/10 100 100 2/10 2/10 0 0 ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C) Symbol IPP Peak pulse current Parameter 10/1000µs 5/310µs 1/20µs tp = 0.2 s tp = 1s tp = 15 min See fig.1 Value 30 45 65 5.5 4.2 1.5 -110 to 0 0 to +95 190 -20 to +85 - 55 to + 150 260 % I PP Unit A ITSM Non repetitive surge peak on-state current (F = 50Hz) A VGN max Maximum negative battery voltage range VGP max Maximum positive battery voltage range ∆ Vbat max Total battery supply voltage Top Tstg TL Operating temperature range (see note 1) Storage temperature range Lead solder temperature (10s duration) V °C °C °C Note 1: Within the Top range, the LCP02-150B1 keeps on operating. The impacts of the ambient temperature are given by derating curves. 100 50 0 tr tp t 2/8 LCP02-150B1 Fig. 1: Test circuit TIP Gn from -110V to +0V 1 TIP Gn NC GND GND NC ∆ Vbat ≤ 190V GP Gp from +0V to +95V RING RING Gn connected to negative supply voltage Gp connected to positive supply voltage ∆ Vbat: differential voltage between VGn and VGp THERMAL RESISTANCE Symbol Rth (j-a) Junction to ambient Parameter Value 150 Unit °C/W 3/8 LCP02-150B1 ELECTRICAL CHARACTERISTICS (Tamb = 25°C) 1 - PARAMETERS RELATED TO THE NEGATIVE SUPPRESSOR Symbol IGn IHIRGLVDGLParameter Negative gate trigger current Holding current (see fig.2) Reverse leakage current Gn/Line Dynamic switching voltage Gn / Line (see note 2) Test conditions VGn/GND = -60V Measured at 50Hz Go-No Go test, VGn = -60V Tj = 25°C, VGn/line = -190V VGn/GND = -60V 10/1000µs 1kV RP = 25Ω IPP = 30A 10/700µs 2kV RP = 25Ω IPP = 30A 1.2/50µs 2kV RP = 25Ω IPP = 30A 150 5 Min. Max. 5 Unit mA mA µA 18 8 15 V 2 - PARAMETERS RELATED TO THE POSITIVE SUPPRESSOR Symbol IGp IRGL+ VDGL+ Parameter Positive gate trigger current Reverse leakage current Gp/LINE Dynamic switching voltage Gp / Line (see note 2) Test conditions VGp/GND = 60V Measured at 50Hz Tj = 25°C, VGp/line = +190V VGp/GND = +60V 10/1000µs 1kV RP = 25Ω IPP = 30A 10/700µs 2kV RP = 25Ω IPP = 30A 1.2/50µs 2kV RP = 25Ω IPP = 30A Min. Max. 5 5 Unit mA µA 18 8 35 V 3 - PARAMETERS RELATED TO LINE/GND Symbol IR Coff Parameter Reverse leakage current Capacitance LINE/GND Test conditions Tj = 25°C, VLINE = +90V, VGP/LINE = +1V Tj = 25°C, VLINE = -105V, VGN/LINE = -1V VR = -3V, F =1MHz, VGp = 60V, VGn = -60V 60 Typ. Max. 5 5 Unit µA pF Note 2: The VDGL value is the difference between the peak line voltage during the surge and the programmed gate voltage. 4/8 LCP02-150B1 Fig. 2: Relative variation of holding current versus junction temperature. Fig. 3: Maximum non repetitive surge peak on state current versus overload duration (with 50Hz sinusoidal wave and initial junction temperature equal to +25°C). IH (T) / IH(25°C) 1.6 1.4 8 10 ITSM (A) 1.2 6 1 0.8 0.6 4 2 T (°C) 0.4 -20 0 20 40 60 80 100 0 0.01 0.1 1 t (s) 10 100 1000 Fig. 4: Capacitance versus reverse applied voltage (typical values) with V GN = -90V and V GP = +90V. C (pF) 70 line + 60 50 40 30 20 10 0 20 40 Vline (V) 60 80 100 line - 5/8 LCP02-150B1 TECHNICAL INFORMATION Fig. 5: LCP02 concept behavior. Rs1 L1 TIP Ign T2 T1 Gn Th1 Th2 Gp V Tip Igp GND -Vbat Cn +Vb Cp Rs2 RING GND L2 V Ring Figure 5 shows the classical protection circuit using the LCP02 crowbar concept. This topology has been developped to protect the new two-battery voltage SLICs. It allows both positive and negative firing thresholds to be programmed. The LCP02-150B1 has two gates (Gn and Gp). Gn is biased to negative battery voltage -Vbat, while Gp is biased to the positive battery voltage +Vb. When a negative surge occurs on one wire (L1 for example), a current Ign flows through the base of the transistor T1 and then injects a current in the gate of the thyristor Th1 which fires. All the surge current flows through the ground. After the surge, when the current flowing through Th1 becomes less negative than the negative holding current Ih-, Th1 switches off. This holding current IH- is temperature dependant as per figure2. When a positive surge occurs on one wire (L1 for example), a current Igp flows through the base of the transistor T2 and then injects a current in the gate of the thyristor Th2 which fires. All the surge current flows through the ground. After the surge, when the current flowing through Th2 becomes less positive than the positive holding current Ih+, Th2 switches off. This holding current IH+, typically 20mA at 25°C, is temperature dependant and the same figure 2 also applies. The capacitors Cn and Cp are used to speed up the crowbar structure firing during the fast rise or fall edges. This allows to minimize the dynamical breakover voltage at the SLIC Tip and Ring inputs during fast surges. Please note that these capacitors are generally available around the SLIC. To be efficient they have to be as close as possible to the LCP02-150B1 gate pins (Gn and Gp) and to the reference ground track (or plan). The optimized value for Cn and Cp is 220nF. The series resistors Rs1 and Rs2 designed in figure 5 represent the fuse resistors or the PTCs which are needed to withstand the power contact or the power induction tests imposed by the country standards. Taking this factor into account, the actual lightning surge current flowing through the LCP02-150B1 is equal to : I surge = Vsurge / (Rg + Rs) With V surge = peak surge voltage imposed by the standard. Rg = series resistor of the surge generator Rs = series resistor of the line card (e.g. PTC) e.g. : For a line card with 50Ω of series resistors which has to be qualified under Bellcore 1000V 10/1000µs surge, the present current through the LCP02-150B1 is equal to : I surge = 1000 / (10 + 50) = 17A 6/8 LCP02-150B1 The LCP02-150B1 topology is particularly optimized for the new telecom applications such as fiber in the loop, WLL systems, decentralized central office for example. The schematics of figures 6 and 7 give the 2 most frequent topologies used for these emergent applications Fig. 6: Protection of SLIC with positive and negative battery voltages. Line card -Vbat Rs (*) TIP Gn TIP Line GND 220nF LCP02 RING Gp 220nF SLIC RING Rs (*) +Vb Rs (*) = PTC or Resistor fuse Fig. 7: Protection of high voltage SLIC Line card Rs (*) -Vbat TIP Gn TIP Line GND 220nF LCP02 RING Gp SLIC RING Rs (*) Rs (*) = PTC or Resistor fuse Figure 6 shows the classical protection topology for SLIC using both positive and negative battery voltages. With such a protection the SLIC is protected against surge over +Vb and lower than -Vbat. In this case, +Vb can be programmed up to +95V while -Vbat can be programmed down to -110V. Please note that the differential voltage does not exceed ∆Vbat max at 190V. Figure 7 gives the protection topology for the new SLIC using high negative voltage down to -110V. 7/8 LCP02-150B1 PACKAGE MECHANICAL DATA SO-8 Wide Plastic REF. L D DIMENSIONS Millimetres Inches Min. Typ. Max. Min. Typ. Max. A 2.50 0.25 1.51 0.35 0.10 0.40 0.20 2.00 0.059 0.099 0.010 0.079 A2 A C A1 A1 A2 b b K E 0.51 0.013 0.016 0.020 0.35 0.003 0.008 0.014 6.05 0.239 0.245 0.35 0.05 10° e c 5 8 D E E1 5.02 7.62 1.27 6.22 0.197 8.89 0.30 E1 1 4 e K L 0.50 0.80 0.019 0.032 ORDER CODE Ordering Type LCP02-150B1 LCP02-150B1RL Marking LCP02 Package SO-8-Wide Weight 0.13g Base qty 90 1500 Delivery mode Tube Tape & Reel Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics © 2000 STMicroelectronics - Printed in Italy - All rights reserved. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com 8/8
LCP02-150B1RL 价格&库存

很抱歉,暂时无法提供与“LCP02-150B1RL”相匹配的价格&库存,您可以联系我们找货

免费人工找货