LNBP9K7-R

LNBP8 LNBP9 LNB Supply and control voltage regulator Feature summary ■ ■ ■ ■ ■ ■ ■ ■ ■ Simplest integrated solution for the LNB remote supply and control 500mA Guaranteed output current Dual input supply for reducing power dissipation 22KHZ Built-in tone oscillator (LNBP9 version) Fast oscillator start-up for DiSEqCTM encoding (LNBP9 version) Auxiliary modulation input for more flexibility (LNBP8 version) Stand-by function Short circuit and overtemperature protection Available in through-hole package SPAK-7L (PowerFlexTM) Description Intended for analog and digital satellite receivers, the LNBP is a monolithic linear voltage regulator, assembled in PowerFlexTM, specifically designed to provide the powering voltages and the interfacing signals to the LNB down-converter. bs O The regulator output can be logic controlled to be 13V or 18V (typ.) by mean of the VSEL pin for the remote controlling of the LNB. In order to reduce the power dissipation of the device when the lowest output voltage is selected, the regulator has 2 supply inputs (VCC1 and VCC2). They must be powered respectively at 15V (min.) and 22V (min.), and an internal switch will automatically select the appropriate supply voltage according to the selected output voltage. let o Pr e du o (s) ct so Ob - ..The TONE pin (only for the LNBP9 version) activates the internal oscillator so that the DC output is modulated by a 22KHz square wave. This internal oscillator is factory trimmed within a tolerance of +/- 2KHz, thus no further adjustment or external components are required. A burst coding of the 22KHz tone can be accomplished thanks to the fast response of the TONE input and the prompt oscillator start-up. This helps designers which want to implement the DiSEqCTM protocols. In order to improve design flexibility and to allow implementation of other LNB remote control standards, an analogic modulation input pin (EXTM) is available (LNBP8 version only). An appropriate DC blocking capacitor must be used to couple the modulating signal source to the EXTM pin. Both versions integrate thermal and short circuit protection. The device is packaged in PowerFlex for an easy through-hole mounting. If an adequate Heatsink is provided and higher power losses are acceptable, both supply pins can be powered by the same 23V source without affecting any other circuit performance. te le ro P uc d s) t( When the IC is powered and put in Stand-by (EN pin LOW), the regulator output is disabled and the IC power consumption is reduced to 300µA typ. Order code Package Part number SPAK-7L LNBP8 LNBP9 September 2006 LNBP8K7 LNBP9K7 Rev. 3 Tape & reel LNBP8K7-R LNBP9K7-R 1/13 www.st.com 13 Packaging LNBP8-LNBP9 Contents 1 2 3 4 5 6 7 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Typical application circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 bs O let o Pr e du o (s) ct so Ob - te le ro P uc d s) t( 2/13 LNBP8-LNBP9 Pin configuration 1 Figure 1. Pin configuration Pin connections (top view) Table 1. Pin N° 1 2 3 4 5 6 7 (LNBP9) 7 (LNBP8) Pin descriptions Name VCC1 VCC2 function Supply Input 1: 15V to 25V supply. It is automatically selected when VO = 13V Supply Input 2: 22V to 25V supply. It is automatically selected when VO = 18V OUTPUT Regulator output. It is 13V typ. when VSEL LOW and 18V typ. when VSEL HIGH GND VSEL ENABLE TONE EXTM GROUND Output Voltage Selection: Logic Control Input; if LOW VO = 13V, when HIGH VO = 18V Logic Control Input; force LOW to put the IC in shutdown Logic Control Input; force HIGH to activate the internal 22KHz tone External Modulation: Needs DC decoupling to the AC source. If not used can be left floating bs O let o Pr e du o (s) ct so Ob - te le ro P uc d s) t( 3/13 Maximum ratings LNBP8-LNBP9 2 Table 2. Symbol VCC1, VCC2 Maximum ratings Absolute maximum ratings Parameter Input voltage Value -0.3 to 28 -0.3 to 7 -0.3 to 28 -40 to 125 -55 to 150 Unit V V V °C °C ENABLE, Logic input voltage TONE, VSEL VO TJ TSTG Output voltage Operating junction temperature range Storage temperature range Note: Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied Thermal data Parameter Thermal resistance junction-case Value Table 3. Symbol RthJC bs O let o Pr e du o (s) ct so Ob - te le ro P 2 uc d s) t( Unit °C/W 4/13 LNBP8-LNBP9 Block diagram 3 Figure 2. Block diagram Block diagram bs O let o Pr e du o (s) ct so Ob - te le ro P uc d s) t( 5/13 Electrical characteristics LNBP8-LNBP9 4 Table 4. Electrical characteristics Electrical characteristics for LNBP Series (VCC1 = 16V, VCC2 = 22V, CI1 = CI2 = 0.22µF, CO =0.1µF, Enable = H, Tone = L (LNBP9), EXTM floating (LNBP8), IO = 50mA, TJ = 0 to 85°C unless otherwise specified.) Parameter Test conditions Min. 15 22 12.5 17.3 13 18 4 4 80 500 LNBP9 version, TONE = H LNBP9 version, TONE = H LNBP9 version, TONE = H LNBP9 version, TONE = H LNBP8 version, ∆VO/∆VEXTM, f = 10Hz to 40KHz LNBP8 version, AC Coupling 20 0.55 Typ. Max. 25 25 13.5 18.7 40 mV 40 180 Unit V V V V Symbol VCC1 VCC2 VO ∆VO ∆VO IMAX fTONE ATONE DTONE tr, tf GEXTM VEXTM ZEXTM VIL VIH IIH VCC Supply voltage input 1 IO = 500 mA, TONE = H, VSEL = L VCC Supply voltage input 2 IO = 500 mA, TONE = H, VSEL = H Output voltage IO = 500 mA, VSEL = L IO = 500 mA, VSEL = H Line regulation VCC1 = 15 to 18V, VSEL = L VCC2 = 22 to 25V, VSEL = H Load regulation Output current limiting Tone frequency Tone amplitude Tone duty cycle Tone rise and fall time External modulation gain External modulation input voltage External modulation impedance Control input logic LOW Control input logic HIGH VCC1 = VCC2 = 22V, IO = 50 to 500mA VSEL = L or H 22 LNBP8 version, f = 10Hz to 40KHz ENABLE, TONE (LNBP9 version), VSEL ENABLE, TONE (LNBP9 version), VSEL VIH = 5V, ENABLE, TONE (LNBP9 version), VSEL Output disabled (ENABLE = L) Output enabled (ENABLE = H), TONE = H, IO = 500mA 2.5 Control pins input current ICC O bs TSHDN let o Supply current ro P e du ct (s) Ob - so eP let 40 5 ro 0.72 50 uc d 800 24 s) t( V mV mA KHz 0.9 60 15 % µs 10 5 400 400 0.8 mV Ω V V 20 0.3 3 150 1 6 µA mA mA °C Temperature shutdown 6/13 LNBP8-LNBP9 Typical application circuits 5 Figure 3. Typical application circuits LNBP9 with 22KHz Tone control pin Figure 4. LNBP8 with external 22KHz Input pin (EXTM) bs O let o Pr e du o (s) ct so Ob - te le ro P uc d s) t( 7/13 Typical application circuits LNBP8-LNBP9 Figure 5. Single supply solution 1. In a single supply configuration the presence of the input resistor in the 12-15Ω range is suggested only to reduce the device power dissipation during the 13V output condition. The resistor can be omitted in spite of power dissipation increase. The input diodes are mandatory to protect the device from any reverse current. 2. bs O let o Pr e du o (s) ct so Ob - te le ro P uc d s) t( 8/13 LNBP8-LNBP9 Package mechanical data 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. bs O let o Pr e du o (s) ct so Ob - te le ro P uc d s) t( 9/13 Package mechanical data LNBP8-LNBP9 SPAK-7L MECHANICAL DATA DIM. A A2 C C1 D D1 F G G1 H1 H2 H3 L L1 L2 M N V 3˚ 8.89 0.79 0.25 9.27 8.89 10.41 7.49 9.14 1.04 6˚ 0.350 0.031 3˚ 1.02 7.87 0.63 1.27 7.62 5.59 9.52 9.14 10.67 0.365 0.350 0.410 mm. MIN. 1.78 0.03 0.25 0.25 1.27 8.13 0.79 0.040 0.310 0.025 0.050 0.3 0.220 TYP MAX. 2.03 0.13 MIN. 0.070 0.001 0.010 0.010 0.050 0.320 0.031 inch TYP. MAX. 0.080 0.005 bs O let o Pr e du o (s) ct so Ob - eP let od r 0.295 0.010 uc s) t( 0.375 0.360 0.420 0.360 0.041 6˚ PO13F2/A 10/13 LNBP8-LNBP9 Package mechanical data Tape & Reel SPAK-xL MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 9.70 10.85 2.30 3.9 11.9 9.80 10.95 2.40 4.0 12.0 12.8 20.2 60 14.4 9.90 11.05 2.50 4.1 12.1 0.382 0.423 0.090 0.153 0.468 0.386 0.427 0.094 0.157 0.472 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.390 0.512 MIN. TYP. MAX. 7.086 0.519 inch bs O let o Pr e du o (s) ct so Ob - Pr te le od uc s) t( 0.431 0.098 0.161 0.476 11/13 Revision history LNBP8-LNBP9 7 Table 5. Date Revision history Revision history Revision 1 2 3 First release. Remove package heptawatt and add package SPAK-7L. Add value VO on table 2 and new template. Changes 09-Nov-2004 04-Jul-2005 20-Sep-2006 bs O let o Pr e du o (s) ct so Ob - te le ro P uc d s) t( 12/13 LNBP8-LNBP9 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. O bs The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. let o Pr e du o (s) ct so Ob - te le ro P uc d s) t( ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 13/13