M74HCT4051B1R

M74HCT4051 SINGLE 8-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER s s s s s s s s s s s LOW POWER DISSIPATION: ICC = 4µA (MAX.) at TA=25°C LOGIC LEVEL TRANSLATION TO ENABLE TTL LOGIC SIGNAL TO COMMUNICATE WITH ±5V ANALOG SIGNAL LOW "ON" RESISTANCE: 70Ω TYP. (VCC - VEE = 4.5V) 50Ω TYP. (VCC - VEE = 9V) WIDE ANALOG INPUT VOLTAGE RANGE: ±6V FAST SWITCHING: tpd = 13ns (TYP.) at TA = 25 °C LOW CROSSTALK BETWEEN SWITCHES HIGH ON/OFF OUTPUT VOLTAGE RATIO WIDE OPERATING SUPPLY VOLTAGE RANGE (VCC - VEE) = 2V TO 12V LOW SINE WAVE DISTORTION: 0.02% at VCC - VEE = 9V COMPATIBLE WITH TTL OUTPUTS: VIH = 2V(MIN.) VIL = 0.8V (MAX.) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 4051 DIP SOP TSSOP ORDER CODES PACKAGE DIP SOP TSSOP TUBE T&R M74HCT4051B1R M74HCT4051M1R M74HCT4051RM13TR M74HCT4051TTR DESCRIPTION The M74HCT4051 is a single eight-channel analog MULTIPLEXER/DEMULTIPLEXER fabricated with silicon gate C2MOS technology and it is pin to pin compatible with the equivalent metal gate CMOS4000B series. It contains 8 bidirectional and digitally controlled analog switches. PIN CONNECTION AND IEC LOGIC SYMBOLS A built-in level shifting is included to allow an input range up to ±6V (peak) for an analog signal with digital control signal of 0 to 6V. VEE supply pin is provided for analog input signals. It has an inhibit (INH) input terminal to disable all the switches when high, compatible with TTL output level. For operation as a digital multiplexer/demultiplexer, VEE is connected to GND. A, B and C control inputs select one channel out of eight channels; they are compatible with TTL output level. All inputs are equipped with protection circuits against static discharge and transient excess voltage. March 2003 1/14 M74HCT4051 CONTROL INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No 3 6 7 11, 10, 9 13, 14, 15, 12, 1, 5, 2, 4 8 16 SYMBOL COM OUT/IN INH VEE A, B, C 0 to 7 GND VCC NAME AND FUNCTION Common Output/Input INHIBIT Input Negative Supply Voltage Select Inputs Independent Input/Outputs Ground (0V) Positive Supply Voltage I/O EQUIVALENT CIRCUIT TRUTH TABLE INPUT STATE ON CHANNEL INH L L L L L L L L H C L L L L H H H H X B L L H H L L H H X A L H L H L H L H X 0 1 2 3 4 5 6 7 NONE FUNCTIONAL DIAGRAM 2/14 M74HCT4051 ABSOLUTE MAXIMUM RATINGS Symbol VCC VCC - VEE VI VI/O ICK IIOK IT Supply Voltage Supply Voltage Control Input Voltage Switch I/O Voltage Control Input Diode Current I/O Diode Current Switch Through Current Parameter Value -0.5 to +7 -0.5 to +13 -0.5 to VCC + 0.5 VEE -0.5 to VCC + 0.5 ± 20 ± 20 ± 25 ± 50 500(*) -65 to +150 300 Unit V V V V mA mA mA mA mW °C °C ICC or IGND DC VCC or Ground Current Power Dissipation PD Tstg TL Storage Temperature Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VEE VI VI/O Top tr, tf Supply Voltage Supply Voltage Input Voltage I/O Voltage Operating Temperature Input Rise and Fall Time VCC = 4.5 to 5.5V Parameter Value 4.5 to 5.5 -6 to 0 2 to 12 0 to VCC VEE to VCC -55 to 125 0 to 500 Unit V V V V V °C ns VCC - VEE Supply Voltage 3/14 M74HCT4051 DC SPECIFICATIONS Test Condition Symbol Parameter VCC (V) 4.5 to 5.5 4.5 to 5.5 4.5 4.5 4.5 4.5 ∆RON Difference of ON Resistance between switches Input/Output Leakage Current (SWITCH OFF) Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Input Leakage Current Quiescent Supply Current Additional Quiescent Supply Current per input pin 4.5 4.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 4.5 to 5.5 VEE (V) TA = 25°C Min. 2.0 Value -40 to 85°C -55 to 125°C Unit Typ. Max. Min. Max. Min. Max. 2.0 2.0 V VIHC High Level Input Voltage Low Level Input Voltage ON Resistance VILC 0.8 GND -4.5 GND -4.5 GND -4.5 VI = VIHC or VILC VI/O = VCC to VEE II/O ≤ 2mA VI = VIHC or VILC VI/O = VCC or VEE II/O ≤ 2mA VI = VIHC or VILC VI/O = VCC or VEE II/O ≤ 2mA 85 55 70 50 10 5 180 120 150 100 30 12 ±0.06 ± 0.1 ±0.06 ± 0.1 ± 0.1 4 8 100 360 0.8 225 150 190 125 35 15 ± 0.6 ±1 ± 0.6 ±1 ± 0.1 40 80 450 0.8 270 180 230 150 45 18 ± 1.0 ±1 ± 1.0 ±1 ±1 80 160 490 V RON Ω Ω IOFF GND VOS = VCC or GND VIS = GND or VCC -6.0 VI = VILC or VIHC GND VOS = VCC or GND VI = VIHC or VILC -6.0 GND GND -6.0 VI = VCC or GND VI = VCC or GND µA IIZ µA µA µA II ICC ∆ICC VI = VCC - 2.1V GND other input at VCC or GND µA 4/14 M74HCT4051 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter VCC (V) 4.5 4.5 4.5 4.5 4.5 4.5 VEE (V) GND -4.5 GND -4.5 GND -4.5 CL = 50pF RL = 1KΩ CL = 50pF RL = 1KΩ CL = 50pF TA = 25°C Min. Value -40 to 85°C -55 to 125°C Unit Typ. Max. Min. Max. Min. Max. 5 4 13 11 25 19 12 8 45 34 38 31 15 10 56 43 48 39 18 12 68 51 58 47 ns ns ns ΦI/O tPZL tPZH tPLZ tPHZ Phase Difference Between Input and Output Output Enable Time Output Disable Time CAPACITANCE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) 5.0 5.0 5.0 5.0 5.0 -5.0 -5.0 -5.0 GND VEE (V) TA = 25°C Min. CIN CI/O CI/O CIOS CPD Input Capacitance Common Terminal Capacitance Switch Terminal Capacitance Feed Through Capacitance Power Dissipation Capacitance (note 1) Value -40 to 85°C -55 to 125°C Unit Typ. Max. Min. Max. Min. Max. 5 11 7 0.75 67 10 20 15 2 10 20 15 2 10 20 15 2 pF pF pF pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 5/14 M74HCT4051 ANALOG SWITCH CHARACTERISTICS (GND = 0V;TA = 25°C) Symbol Parameter VCC (V) Sine Wave Distortion Sine Wave Distortion fMAX Frequency Response (Switch ON) (*) Frequency Response (Switch ON) (**) Feed through Attenuation (Switch OFF) Crosstalk (Control Input to Signal Output) Crosstalk (between any two switches) 2.25 4.5 2.25 4.5 2.25 4.5 2.25 4.5 6.0 2.25 4.5 4.5 4.5 VEE (V) -2.25 -4.5 -2.25 -4.5 -2.25 -4.5 -2.25 -4.5 -6.0 -2.25 -4.5 0 -4.5 VIN (Vp-p) 4 8 4 8 Test Condition Value Unit Typ. 0.025 % 0.020 0.12 % 0.06 120 190 MHz 95 150 -50 -50 60 140 fIN = 1 KHz RL = 10 KΩ, CL = 50 pF fIN = 10 KHz RL = 10 KΩ, CL = 50 pF Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF, fIN = 1KHz sine wave Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF, fIN = 1KHz sine wave VIN is centered at (VCC - VEE)/2 Adjust input for 0 dBm RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave fMAX MHz dB Adjust RL at set up so that IS = 0A. RL = 600Ω, CL = 50 pF, fIN = 1MHz square wave between Vcc and GND tr=tf= 6 ns Adjust VIN to obtain 0dBm at input RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave mV 2.25 4.5 -2.25 -4.5 -50 -50 dB (*) Input COMMON Terminal, and measured at SWITCH Terminal (**) Input SWITCH Terminal, and measured at common Terminal NOTE: These characteristics are determined by the design of the device. 6/14 M74HCT4051 SWITCHING CARACTERISTICS TEST CIRCUIT CROSSTALK (control to output) BANDWIDTH AND FEEDTHROUGH ATTENUATION CROSSTALK BETWEEN ANY TWO SWITCHES 7/14 M74HCT4051 SWITCHING CHARACTERISTICS WAVEFORM CHANNEL RESISTANCE (RON) ICC (Opr.) 8/14 M74HCT4051 Plastic DIP-16 (0.25) MECHANICAL DATA mm. DIM. MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.27 8.5 2.54 17.78 7.1 5.1 0.130 0.050 0.51 0.77 0.5 0.25 20 0.335 0.100 0.700 0.280 0.201 1.65 TYP MAX. MIN. 0.020 0.030 0.020 0.010 0.787 0.065 TYP. MAX. inch P001C 9/14 M74HCT4051 SO-16 MECHANICAL DATA DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 8 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 ˚ (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45˚ (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.004 MIN. inch TYP. MAX. 0.068 0.008 0.064 0.018 0.010 PO13H 10/14 M74HCT4051 TSSOP16 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0˚ 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8˚ 0.75 0˚ 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8˚ 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0079 0.201 0.260 0.176 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 11/14 M74HCT4051 Tape & Reel SO-16 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.45 10.3 2.1 3.9 7.9 12.8 20.2 60 22.4 6.65 10.5 2.3 4.1 8.1 0.254 0.406 0.082 0.153 0.311 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.262 0.414 0.090 0.161 0.319 MIN. TYP. MAX. 12.992 0.519 inch 12/14 M74HCT4051 Tape & Reel TSSOP16 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.7 5.3 1.6 3.9 7.9 12.8 20.2 60 22.4 6.9 5.5 1.8 4.1 8.1 0.264 0.209 0.063 0.153 0.311 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.272 0.217 0.071 0.161 0.319 MIN. TYP. MAX. 12.992 0.519 inch 13/14 M74HCT4051 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 14/14