STPS20H100CR

STPS20H100C High voltage power Schottky rectifier Main product characteristics IF(AV) VRRM Tj (max) VF(max) 2 x 10 A 100 V 175° C 0.64 V A2 A2 K A1 K A1 A1 K A2 Features and benefits ■ ■ ■ ■ ■ ■ Negligible switching losses High junction temperature capability Good trade off between leakage current and foward voltage drop Low leakage current Avalanche rated Insulated package: TO-220FPAB Insulating voltage = 2000 V DC Capacitance = 45 pF Avalanche capability specified TO-220AB STPS20H100CT TO-220FPAB STPS20H100CFP K A2 A2 K A1 A1 ■ Description Dual center tap schottky rectifier designed for high frequency miniature switched mode power supplies such as adaptators and on board DC/DC converters. j I2PAK STPS20H100CR D2PAK STPS20H100CG March 2007 Rev 5 1/11 www.st.com 11 Characteristics STPS20H100C 1 Characteristics Table 1. Symbol VRRM IF(RMS) IF(AV) IFSM IRRM IRSM PARM Tstg Tj dV/dt 1. d Ptot --------------dTj Absolute ratings (limiting values, per diode) Parameter Repetitive peak reverse voltage RMS forward current Average forward current δ = 0.5 TO-220AB D2PAK / I2PAK TO-220FPAB Tc = 160° C Per diode Tc = 145° C Per device Value 100 30 10 A 20 250 1 3 10800 -65 to + 175 (1) Unit V A Surge non repetitive forward current tp = 10 ms sinusoidal Repetitive peak reverse current Non repetitive peak reverse current Repetitive peak avalanche power Storage temperature range Maximum operating junction temperature Critical rate of rise of reverse voltage 1 ------------------------Rth ( j – a ) A A A W °C °C V/µs tp = 2 µs square F= 1 kHz tp = 100 µs square tp = 1 µs Tj = 25° C 175 10000 < condition to avoid thermal runaway for a diode on its own heatsink Table 2. Symbol Thermal resistance Parameter TO-220AB / D2PAK / I 2PAK TO-220FPAB Per diode Per diode Total Total Coupling Coupling Value 1.6 °C/W 4 0.9 °C/W TO-220FPAB TO-220AB / D2PAK / I2PAK 3.2 0.15 °C/W TO-220FPAB 2.5 Unit Rth(j-c) Junction to case TO-220AB / D2PAK / I2PAK Rth(c) When the diodes 1 and 2 are used simultaneously: ΔTj(diode 1) = P(diode1) x Rth(j-c)(Per diode) + P(diode 2) x Rth(c) 2/11 STPS20H100C Table 3. Symbol IR(1) Characteristics Static electrical characteristics (per diode) Parameter Reverse leakage current Test conditions Tj = 25° C Tj = 125° C Tj = 25° C Tj = 25° C Tj = 25° C VR = VRRM IF = 8 A IF = 10 A IF = 16 A IF = 20 A IF = 8 A IF = 10 A IF = 16 A IF = 20 A 0.56 0.59 0.65 0.67 Min. Typ. Max. 4.5 2 6 0.71 0.77 0.81 0.88 V 0.58 0.64 0.68 0.73 Unit µA mA VF(2) Forward voltage drop Tj = 25° C Tj = 125° C Tj = 125° C Tj = 125° C Tj = 125° C 1. Pulse test: tp = 5 ms, δ < 2% 2. Pulse test: tp = 380 µs, δ < 2% To evaluate the conduction losses use the following equation: P = 0.55 x IF(AV) + 0.009 IF2(RMS) 3/11 Characteristics STPS20H100C Figure 1. Average forward power dissipation Figure 2. versus average forward current (per diode) IF(AV)(A) δ = 0.1 δ = 0.05 δ = 0.2 Average forward current versus ambient temperature (δ = 0.5, per diode) PF(AV)(W) 8 12 δ = 0.5 Rth(j-a)=Rth(j-c) TO-220AB 10 Rth(j-a)=15°C/W 6 δ=1 4 8 Rth(j-a)=40°C/W TO-220FPAB 6 4 2 T T 2 IF(AV)(A) 0 0 2 4 6 8 δ=tp/T 10 tp 0 12 δ=tp/T 0 25 tp Tamb(°C) 50 75 100 125 150 175 Figure 3. Normalized avalanche power derating versus pulse duration Figure 4. Normalized avalanche power derating versus junction temperature PARM(tp) PARM(1µs) 1 1.2 1 0.1 0.8 0.6 0.4 0.2 0.001 0.01 0.1 1 PARM(tp) PARM(25°C) 0.01 tp(µs) 10 100 1000 Tj(°C) 0 25 50 75 100 125 150 Figure 5. Non repetitive surge peak forward current versus overload duration (maximum values, per diode, TO-220AB, D2PAK, I2PAK) Figure 6. Non repetitive surge peak forward current versus overload duration (maximum values, per diode, TO-220FPAB) IM(A) 200 180 160 140 120 100 80 60 40 20 0 1E-3 IM t IM(A) 140 120 100 TC=50°C 80 60 Tj=50°C TC=75°C Tj=75°C TC=125°C 40 IM Tj=125°C t 20 δ=0.5 t(s) 1E-2 1E-1 1E+0 0 1E-3 δ=0.5 t(s) 1E-2 1E-1 1E+0 4/11 STPS20H100C Characteristics Figure 7. Figure 8. Relative variation of thermal impedance junction to case versus pulse duration (per diode, TO-220AB, D2PAK, I2PAK) 1.0 Relative variation of thermal impedance junction to case versus pulse duration (per diode, TO-220FPAB) Zth(j-c)/Rth(j-c) 1.0 Zth(j-c)/Rth(j-c) 0.8 δ = 0.5 0.8 δ = 0.5 0.6 0.6 0.4 δ = 0.2 δ = 0.1 0.4 T δ = 0.2 δ = 0.1 T 0.2 Single pulse 0.2 Single pulse tp(s) 0.0 1E-3 1E-2 1E-1 δ=tp/T tp tp(s) 1E+0 0.0 1E-2 1E-1 1E+0 δ=tp/T tp 1E+1 Figure 9. Reverse leakage current versus reverse voltage applied (typical values, per diode) Figure 10. Junction capacitance versus reverse voltage applied (typical values, per diode) C(pF) 1000 IR(µA) 1E+4 1E+3 1E+2 1E+1 1E+0 1E-1 1E-2 0 10 20 30 40 50 60 70 80 90 100 Tj=25°C Tj=150°C F=1MHz VOSC=30mVRMS Tj=25°C Tj=125°C 500 Tj=100°C 200 VR(V) 100 1 2 5 VR(V) 10 20 50 100 Figure 11. Forward voltage drop versus forward current (maximum values, per diode) IFM(A) 100.0 Tj=150°C (typical values) Figure 12. Thermal resistance junction to ambient versus copper surface under tab (epoxy printed circuit board FR4, Cu = 35 µm, D2PAK) Rth(j-a)(°C/W) 80 70 60 10.0 Tj=125°C (typical values) Tj=125°C 50 40 30 20 10 Tj=25°C 1.0 VFM(V) 0.1 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0 0 5 10 15 S(Cu)(cm²) 20 25 30 35 40 5/11 Package information STPS20H100C 2 Package information ● ● ● ● Epoxy meets UL94, V0 Cooling method: by conduction (C) Recommended torque value: 0.55 Nm Maximum torque value: 0.70 Nm TO-220AB dimensions Dimensions Ref Millimeters Min. A H2 Dia L5 L7 L6 C A Table 4. Inches Min. 0.173 0.048 0.094 0.019 0.024 0.044 0.044 0.194 0.094 0.393 Max. 0.181 0.051 0.107 0.027 0.034 0.066 0.066 0.202 0.106 0.409 Max. 4.60 1.32 2.72 0.70 0.88 1.70 1.70 5.15 2.70 10.40 4.40 1.23 2.40 0.49 0.61 1.14 1.14 4.95 2.40 10 C D E F F1 F2 L2 F2 F1 L9 L4 F G1 G M E D G G1 H2 L2 L4 L5 L6 L7 L9 M Diam. 16.4 typ. 13 2.65 15.25 6.20 3.50 14 2.95 15.75 6.60 3.93 0.645 typ. 0.511 0.104 0.600 0.244 0.137 0.551 0.116 0.620 0.259 0.154 2.6 typ. 3.75 3.85 0.102 typ. 0.147 0.151 6/11 STPS20H100C Table 5. TO-220FPAB dimensions Package information Dimensions Ref Millimeters Min. A A H B Inches Min. 0.173 0.098 0.098 0.018 0.30 0.045 0.045 0.195 0.094 0.393 Max. 0.181 0.106 0.108 0.027 0.039 0.067 0.067 0.205 0.106 0.409 Max. 4.6 2.7 2.75 0.70 1 1.70 1.70 5.20 2.7 10.4 4.4 2.5 2.5 0.45 0.75 1.15 1.15 4.95 2.4 10 B D E Dia L6 L2 L3 L5 F1 L4 F2 D L7 F F1 F2 G G1 H L2 16 typ. 28.6 9.8 2.9 15.9 9.00 3 30.6 10.6 3.6 16.4 9.30 3.20 0.63 typ. 1.126 0.386 0.114 0.626 0.354 0.118 1.205 0.417 0.142 0.646 0.366 0.126 F G1 E L3 L4 G L5 L6 L7 Dia. 7/11 Package information Table 6. D2PAK dimensions STPS20H100C Dimensions Ref Millimeters Min. A A E L2 Inches Min. 0.173 0.098 0.001 0.027 0.045 0.017 0.048 0.352 0.393 0.192 0.590 0.050 0.055 0.094 Max. 0.181 0.106 0.009 0.037 0.067 0.024 0.054 0.368 0.409 0.208 0.624 0.055 0.069 0.126 Max. 4.60 2.69 0.23 0.93 1.70 0.60 1.36 9.35 10.40 5.28 15.85 1.40 1.75 3.20 4.40 2.49 0.03 0.70 1.14 0.45 1.23 8.95 10.00 4.88 15.00 1.27 1.40 2.40 A1 C2 A2 B D L L3 A1 B2 B G A2 B2 C C2 C R D E G L M * V2 L2 L3 M R V2 * FLAT ZONE NO LESS THAN 2mm 0.40 typ. 0° 8° 0.016 typ. 0° 8° Figure 13. Footprint (dimensions in millimeters) 16.90 10.30 1.30 5.08 8.90 3.70 8/11 STPS20H100C Table 7. I2PAK dimensions Package information Dimensions Ref Millimeters Min. A E L2 c2 Inches Min. 0.173 0.098 0.028 0.044 0.044 0.018 0.048 0.352 0.094 0.394 0.516 0.137 0.050 Max. 0.181 0.106 0.037 0.046 0.046 0.024 0.054 0.368 0.106 0.409 0.535 0.149 0.055 Max. 4.60 2.69 0.93 1.17 1.17 0.60 1.36 9.35 2.70 10.4 13.6 3.78 1.40 A A1 b b1 4.40 2.49 0.70 1.14 1.14 0.45 1.23 8.95 2.40 10.0 13.1 3.48 1.27 D b2 c L1 L b1 A1 c2 D e E b e e1 c L L1 L2 In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 9/11 Ordering information STPS20H100C 3 Ordering information Delivery mode Tube Tube Tube Tube Tape & reel Ordering type STPS20H100CT STPS20H100CFP STPS20H100CR STPS20H100CG STPS20H100CG-TR Marking STPS20H100CT STPS20H100CFP STPS20H100CR STPS20H100CG STPS20H100CG Package TO-220AB TO-220FPAB I PAK D2PAK D2 PAK 2 Weight Base qty 2.20 g 2.0 g 1.49 g 1.48 g 1.48 g 50 50 50 50 1000 4 Revision history Date Jul-2003 21-Mar-2007 Revision 4G 5 Last release. Removed ISOWATT package. Description of Changes 10/11 STPS20H100C Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 11/11