STTH3006PI

STTH3006 Turbo 2 ultrafast high voltage rectifier Datasheet - production data Description The device is developed using ST's Turbo 2 600 V technology. It is well-suited as a boost diode, especially for use in continuous mode power factor corrections and hard switching conditions. This device is also intended for use as a free wheeling diode in power supplies and other power switching applications. Table 1: Device summary Features      Ultrafast switching Low reverse current Low thermal resistance Reduces switching and conduction losses Insulated package: DOP3I  Insulating voltage = 2500 VRMS sine May 2017 DocID12368 Rev 4 This is information on a product in full production. Symbol Value IF(AV) 30 A VRRM 600 V VF (typ.) 1.10 V Tj 175 °C trr (max) 50 ns 1/12 www.st.com Characteristics 1 STTH3006 Characteristics Table 2: Absolute ratings (limiting values at 25 °C, unless otherwise specified) Symbol Parameter Value Unit VRRM Repetitive peak reverse voltage 600 V IF(RMS) Forward rms current 50 A Average forward current, δ = 0.5 square wave DO-247 TC = 115 °C IF(AV) DOP3I TC = 85 °C 30 A IFSM Surge non repetitive forward current tp = 10 ms sinusoidal 300 A Tstg Storage temperature range -65 to +175 °C 175 °C Tj Maximum operating junction temperature Table 3: Thermal parameters Symbol Rth(j-c) Parameter Max. value DO-247 1.1 DOP3I 1.7 Junction to case Unit °C/W Table 4: Static electrical characteristics Symbol Parameter Test conditions IR(1) Reverse leakage current VF(2) Forward voltage drop Tj = 25 °C Tj = 150 °C Tj = 25 °C Tj = 150 °C VR = VRRM IF = 30 A Notes: (1)Pulse test: tp = 5 ms, δ < 2% (2)Pulse test: tp = 380 µs, δ < 2% To evaluate the conduction losses, use the following equation: P = 1.07 x IF(AV) + 0.011 x IF2(RMS) 2/12 DocID12368 Rev 4 Min. Typ. - 25 80 - Max. 800 1.85 1.10 1.40 Unit µA V STTH3006 Characteristics Table 5: Dynamic electrical characteristics Symbol Parameter Test conditions IF = 0.5 A Irr = 0.25 A IR = 1 A trr IRM tfr VFP Reverse recovery time Reverse recovery current Typ. - Max. Unit 50 Tj = 25 °C ns IF = 1 A VR = 30 V dIF/dt = -50 A/µs - 50 70 Tj = 125 °C IF = 30 A VR = 400 V dIF/dt = -100 A/µs - 8 11 A IF = 30 A VFR = 1.1 x VF max dIF/dt = 100 A/µs 500 ns Tj = 25 °C Forward recovery time Forward recovery voltage Min. DocID12368 Rev 4 - 2.5 V 3/12 Characteristics 1.1 STTH3006 Characteristics (curves) Figure 1: Conduction losses versus average forward current Figure 2: Forward voltage drop versus forward current PF( AV )(W) 55 δ = 0.5 50 δ = 0.2 45 δ = 0.1 40 δ=1 δ = 0.05 35 30 25 20 T 15 10 IF( AV ) ( A) 5 δ=tp/T tp 0 0 5 10 15 20 25 30 35 Figure 3: Relative variation of thermal impedance junction to case versus pulse duration Figure 4: Peak reverse recovery current versus dIF/dt (typical values) Zth (j-c) /Rth(j-c) IRM(A) 1.0 30 IF =2 x I F(AV ) VR = 400 V Tj = 125°C 0.9 25 IF =I F(AV ) 0.8 IF =0.5 x I F(AV ) 0.7 20 IF =0.25 x I F(AV ) 0.6 15 0.5 0.4 10 0.3 5 0.2 dIF/dt(A/µs) Single pulse t P (s) 0.1 0 0 0.0 1.E -03 1.E -02 1.E -01 Figure 5: Reverse recovery time versus dIF/dt (typical values) trr(ns) VR = 400 V Tj = 125°C IF =2 x I F(AV ) IF =I F(AV ) IF =0.5 x I F(AV ) 100 50 dIF/dt(A/µs) 0 0 4/12 200 400 600 100 150 200 250 300 350 400 450 500 Figure 6: Reverse recovery charges versus dIF/dt (typical values) 200 150 50 1.E +00 800 1000 DocID12368 Rev 4 STTH3006 Characteristics Figure 8: Relative variations of dynamic parameters versus junction temperature Figure 7: Softness factor versus dIF/dt (typical values) Sfactor 0.6 IF ≤ 2 x IF(AV) VR = 400 V Tj = 125°C 0.5 0.4 0.3 0.2 0.1 dIF/dt(A/µs) 0.0 0 50 100 150 200 250 300 350 400 450 500 Figure 9: Transient peak forward voltage versus dIF/dt (typical values) Figure 10: Forward recovery time versus dIF/dt (typical values) VFP(V) t FR(ns) 8.0 800 7.5 IF = IF(AV) VR = 400 V Tj = 125°C 7.0 6.5 IF ≤ 2 x IF(AV) VR = 400 V Tj = 125°C 700 6.0 600 5.5 5.0 500 4.5 4.0 400 3.5 3.0 300 2.5 200 2.0 1.5 100 1.0 0.5 dIF/dt(A/µs) dIF/dt(A/µs) 0.0 0 100 200 0 300 400 500 DocID12368 Rev 4 0 100 200 300 400 5/12 500 Characteristics STTH3006 Figure 11: Junction capacitance versus reverse voltage applied (typical values) 6/12 DocID12368 Rev 4 Package information STTH3006 2 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.      Epoxy meets UL94, V0 Cooling method: by conduction (C) Recommended torque value: 0.55 N·m (DO-247) Recommended torque value: 0.9 to 1.2 N·m (DOP3I) Maximum torque value: 1.0 N·m (DO-247) DocID12368 Rev 4 7/12 Package information 2.1 STTH3006 DO247 package information Figure 12: DO-247 package outline 8/12 DocID12368 Rev 4 Package information STTH3006 Table 6: DO-247 package mechanical data Dimensions Ref. Millimeters Inches Min. Max. Min. Max. A 4.85 5.15 0.191 0.203 D 2.20 2.60 0.086 0.102 E 0.40 0.80 0.015 0.031 F 1.00 1.40 0.039 0.055 F2 F3 2.00 typ. 2.00 G 0.078 typ. 2.40 0.078 10.90 typ. 0.094 0.429 typ. H 15.45 15.75 0.608 0.620 L 19.85 20.15 0.781 0.793 L1 3.70 4.30 0.145 0.169 L2 L3 18.50 typ. 14.20 0.728 typ. 14.80 0.559 0.582 L4 34.60 typ. 1.362 typ. L5 5.50 typ. 0.216 typ. M 2.00 V 0.078 5° V2 Dia. 3.00 5° 60° 3.55 0.118 60° 3.65 DocID12368 Rev 4 0.139 0.143 9/12 Package information 2.2 STTH3006 DOP3I package information Figure 13: DOP3I package outline Table 7: DOP3I package mechanical data Dimensions Ref. Millimeters Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 b 1.20 1.40 0.047 0.055 c 1.45 1.55 0.057 0.061 c1 0.50 0.70 0.020 0.028 D 12.15 13.10 0.474 0.516 E 15.10 15.50 0.594 0.610 E1 7.55 7.75 0.297 0.305 e 10.80 11.30 0.425 0.445 G 20.4 21.10 0.815 0.831 L 14.35 15.60 0.565 0.614 P 4.08 4.17 0.161 0.164 Q 2.70 2.90 0.106 0.114 R Y 10/12 Inches 4.60 15.80 0.181 16.50 DocID12368 Rev 4 0.622 0.650 Ordering information STTH3006 3 Ordering information Table 8: Ordering information 4 Order code Marking Package Weight Base qty. Delivery mode STTH3006W STTH3006W DO-247 4.40 g 30 Tube STTH3006PI STTH3006P DOP3I 4.46 g 30 Tube Revision history Table 9: Document revision history Date Revision 17-May-2017 1 Changes First issue. DocID12368 Rev 4 11/12 STTH3006 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2017 STMicroelectronics – All rights reserved 12/12 DocID12368 Rev 4