VN820SP13TR

® VN820 / VN820SO / VN820SP / VN820-B5 / VN820PT HIGH SIDE DRIVER TYPE VN820 VN820SP VN820-B5 VN820SO VN820PT RDS(on) IOUT VCC 10 40 mΩ 9A 36 V 1 PowerSO-10™ P2PAK PPAK C MOS COMPATIBLE INPUT ON STATE OPEN LOAD DETECTION s O FF STATE OPEN LOAD DETECTION s SHORTED LOAD PROTECTION s UNDERVOLTAGE AND OVERVOLTAGE SHUTDOWN s PROTECTION AGAINST LOSS OF GROUND s VERY LOW STAND-BY CURRENT s s s PENTAWATT PACKAGE PENTAWATT TUBE SO-16L T&R ORDER CODES VN820 VN820SP VN820-B5 VN820SO VN820PT VN820SP13TR VN820-B513TR VN820SO13TR VN820PT13TR REVERSE BATTERY PROTECTION (*) PowerSO-10™ P2PAK SO-16L PPAK DESCRIPTION The VN820, VN820SP, VN820-B5, VN820SO, VN820PT are monolithic devices made by using STMicroelectronics VIPower M0-3 Technology, intended for driving any kind of load with one side connected to ground. Active V CC pin voltage clamp protects the device against low energy spikes (see ISO7637 transient BLOCK DIAGRAM compatibility table). Active current limitation combined with thermal shutdown and automatic restart protect the device against overload. The device detects open load condition both is on and off state. Output shorted to VCC is detected in the off state. Device automatically turns off in case of ground pin disconnection. VCC VCC CLAMP OVERVOLTAGE DETECTION UNDERVOLTAGE DETECTION GND Power CLAMP INPUT LOGIC DRIVER OUTPUT CURRENT LIMITER STATUS ON STATE OPENLOAD DETECTION OVERTEMPERATURE DETECTION OFF STATE OPENLOAD AND OUTPUT SHORTED TO V CC DETECTION (*) See application schematic at page 9 Rev. 1 1/35 July 2004 VN820 / VN820SO / VN820SP / VN820-B5 / VN820PT ABSOLUTE MAXIMUM RATING Symbol VCC - VCC - IGND IOUT - IOUT IIN ISTAT Parameter DC Supply Voltage Reverse DC Supply Voltage DC Reverse Ground Pin Current DC Output Current Reverse DC Output Current DC Input Current DC Status Current Electrostatic Discharge (Human Body Model: R=1.5KΩ; C=100pF) VESD - INPUT - STATUS - OUTPUT - VCC Maximum Switching Energy (L=4mH; RL=0Ω; Vbat=13.5V; Tjstart=150ºC; IL=13A) Maximum Switching Energy (L=3.7mH; RL=0Ω; Vbat=13.5V; Tjstart=150ºC; IL=13A) Maximum Switching Energy (L=4.48mH; RL=0Ω; Vbat=13.5V; Tjstart=150ºC; IL=13A) Power Dissipation TC=25°C Junction Operating Temperature Case Operating Temperature Storage Temperature 4000 4000 5000 5000 481 481 438 526 65.8 65.8 65.8 Internally Limited - 40 to 150 - 55 to 150 8.3 65.8 V V V V mJ mJ mJ W °C °C °C Value Unit PowerSO-10™ PENTAWATT P2PAK SO-16L PPAK 41 V - 0.3 V - 200 mA Internally Limited A -9 A +/- 10 mA +/- 10 mA EMAX EMAX EMAX Ptot Tj Tc Tstg CONFIGURATION DIAGRAM (TOP VIEW) & SUGGESTED CONNECTIONS FOR UNUSED AND N.C. PINS GROUND INPUT ST TUS A N.C. N.C. 6 7 8 9 10 11 5 4 3 2 1 OUTPUT OUTPUT N.C. OUTPUT OUTPUT VCC N.C. GND INPUT STATUS N.C. N.C. VCC 1 16 VCC OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT VCC PowerSO-10™ PPAK / P2PAK / PENTAWATT N.C. X X Output X Input X Through 10KΩ resistor Connection / Pin Status Floating X To Ground 8 9 VCC SO-16L CURRENT AND VOLTAGE CONVENTIONS IS VF IIN INPUT ISTAT STATUS VCC IOUT OUTPUT GND VCC VIN VSTAT IGND VOUT 2/35 VN820 / VN820SO / VN820SP / VN820-B5 / VN820PT THERMAL DATA Symbol Rthj-case Rthj-lead Rthj-amb Rthj-amb (1) (2) Parameter Thermal Resistance Junction-case Thermal Resistance Junction-lead Thermal Resistance Junction-ambient Thermal Resistance Junction-ambient Max Max Max Max Value PowerSO-10 PENTAWATT P2PAK SO-16L PPAK 1.9 1.9 1.9 1.9 15 (1) (1) (1) 65 (2) 76.9 (1) 51.9 61.9 51.9 37 (3) 37 (3) 48 (4) 45 (3) Unit °C/W °C/W °C/W °C/W When mounted on a standard single-sided FR-4 board with 0.5cm2 of Cu (at least 35µm thick). When mounted on FR4 printed circuit board with 0.5cm2 of Cu (at least 35µ thick) connected to all VCC pins. (3) When mounted on a standard single-sided FR-4 board with 6cm2 of Cu (at least 35µm thick). (4) When mounted on FR4 printed circuit board with 6cm2 o f Cu (at least 35µ thick) connected to all V CC pins. ELECTRICAL CHARACTERISTICS (8V VOL Output Current < IOL INPUT L H L H H L H L H L H L H L H OUTPUT L H L X X L L L L L L H H L H STATUS H H H (Tj < TTSD) H (Tj > TTSD) L H L X X H H L H H L 5/35 1 VN820 / VN820SO / VN820SP / VN820-B5 / VN820PT OPEN LOAD DETECTION IN OFF STATE Off state open load detection requires an external pull-up resistor (RPU) connected between OUTPUT pin and a positive supply voltage (VPU) like the +5V line used to supply the microprocessor. The external resistor has to be selected according to the following requirements: 1) no false open load indication when load is connected: in this case we have to avoid VOUT to be higher than VOlmin; this results in the following condition VOUT=(VPU/(RL+RPU))RL