BU08RA06

for General Electronic Equipment Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product Information in this Catalog Product information in this catalog is as of October 2020. All All of of the the January 2021. contents specified herein and production status of the products listed in this catalog are subject to change without notice due to technical improvement of our products, etc. Therefore, please check for the latest information carefully before practical application or use of our products. (4) Powe r g e n e r atio n c o ntro l e quip m e nt (nu c le a r p owe r, hydroelectric power, thermal power plant control system, etc.) (5) Undersea equipment (submarine repeating equipment, underwater work equipment, etc.) (6) Military equipment (7) Any other equipment requiring extremely high levels of safety and/or reliability equal to the equipment listed above Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. *Notes: 1. There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. 2. Implantable medical devices contain not only internal unit which is implanted in a body, but also external unit which is connected to the internal unit. ■ Approval of Product Specifications Ple a se c ont ac t TA IYO YUD EN for fur the r det a ils of p ro duc t specifications as the individual product specification sheets are available. When using our products, please be sure to approve our product specifications or make a written agreement on the product specification with TAIYO YUDEN in advance. ■ Pre-Evaluation in the Actual Equipment and Conditions Please conduct validation and verification of our products in actual conditions of mounting and operating environment before using our products. ■ Limited Application 1. Equipment Intended for Use The products listed in this catalog are intended for generalpurpose and standard use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC) and other equipment specified in this catalog or the individual product specification sheets. TAIYO YUDEN has the line-up of the products intended for use in automotive electronic equipment, telecommunications infrastructure and industrial equipment, or medical devices classified as GHTF Classes A to C (Japan Classes I to III). Therefore, when using our products for these equipment, please check available applications specified in this catalog or the individual product specification sheets and use the corresponding products. 2. Equipment Requiring Inquiry Please be sure to contact TAIYO YUDEN for further information before using the products listed in this catalog for the following equipment (excluding intended equipment as specified in this catalog or the individual product specification sheets) which may cause loss of human life, bodily injury, serious property damage and/or serious public impact due to a failure or defect of the products and/or malfunction attributed thereto. (1) Transportation equipment (automotive powertrain control system, train control system, and ship control system, etc.) (2) Traffic signal equipment (3) Disaster prevention equipment, crime prevention equipment (4) Medical devices classified as GHTF Class C (Japan Class III) (5) H i g h l y p u b l i c i n f o r m a t i o n n e t wo r k e q u i p m e n t , d a t a processing equipment (telephone exchange, and base station, etc.) (6) Any other equipment requiring high levels of quality and/or reliability equal to the equipment listed above 3. Equipment Prohibited for Use Please do not incorporate our products into the following equipment requiring extremely high levels of safety and/or reliability. (1) Aerospace equipment (artificial satellite, rocket, etc.) (2) Aviation equipment *1 (3) Medical devices classified as GHTF Class D (Japan Class IV), implantable medical devices *2 4. Limitation of Liability Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment that is not intended for use by TAIYO YUDEN, or any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Safety Design When using our products for high safety and/or reliability-required equipment or circuits, please fully perform safety and/or reliability evaluation. In addition, please install (i) systems equipped with a protection circuit and a protection device and/or (ii) systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault for a failsafe design to ensure safety. ■ Intellectual Property Rights Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. ■ Limited Warranty Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a failure or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. ■ TAIYO YUDEN’s Official Sales Channel The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter “TAIYO YUDEN’ s official sales channel”). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’ s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export Administration Regulations”,“Foreign Exchange and Foreign Trade Control Law” of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 2 21 for General Electronic Equipment LEADED COMMON MODE CHOKE COILS FOR DC AND SIGNAL LINES LEADED COMMON MODE CHOKE COILS FOR DC AND SIGNAL LINES WAVE ■PARTS NUMBER T L F ① △ 9 ② U B H ③ 3 0 2 ④ W ⑤ K 1 △＝Blank space ⑥ ④Nominal inductance Code （example） 302 203 ⑤Inductance tolerance Code W ⑥Internal code Code K1 Series name Common mode choke coil Dimensions of core［mm］ 9 Shape U core, vertically split wound U core, horizontally split wound Nominal inductance［μH］ 3000 20000 Inductance tolerance ＋100/－10％ NOISE SUPPRESSION COMPONENTS ①Series name Code TLF ②Dimensions of core Code △9 ③Shape Code UB△ UBH * Operating Temp.：-25～+105℃（Including self-generated heat） Internal code Adhesive fixation ■STANDARD EXTERNAL DIMENSIONS / MINIMUM QUANTITY TLF 9UB Type 11.0max TLF 9UBH Type 17.0max 17.0max 15.0max COMMON MODE CHOKE COILS 12.0max 16.0max φ0.6 φ0.6 ④ 4.5±1.0 4.5±1.0 ④ ③ ③ 8.0±0.5 （0.315±0.020） ① 7.0±0.5 （0.276±0.020） 8.0±0.5 （0.315±0.020） ① ② 7.0±0.5 （0.276±0.020） ② Minimum quantity (pcs.) Box 500 Minimum quantity (pcs.) Box 500 Unit：mm（inch） ■PARTS NUMBER Parts number TLF TLF TLF TLF TLF TLF 9UBH302W 9UB 302W 9UBH802W 9UB 802W 9UBH203W 9UB 203W K1 K1 K1 K1 K1 K1 EHS Number of lines Nominal inductance ［mH］ Inductance tolerance DC Resistance ［Ω］（max.） Rated current ［A］（max.） Rated voltage ［V］（D.C.） Insulation resistance ［MΩ］（min.） RoHS RoHS RoHS RoHS RoHS RoHS 2 2 2 2 2 2 3.0 3.0 8.0 8.0 20.0 20.0 ＋100/－10％ ＋100/－10％ ＋100/－10％ ＋100/－10％ ＋100/－10％ ＋100/－10％ 1.5 1.5 3.0 3.0 6.5 6.5 0.40 0.40 0.30 0.30 0.18 0.18 50 50 50 50 50 50 100 100 100 100 100 100 coil_leaded_dc_signalline_e-E08R01.doc ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 21 91 LEADED COMMON MODE CHOKE COILS FOR DC AND SIGNAL LINES LEADED COMMON MODE CHOKE COILS FOR AC LINES ■PACKAGING ①Minimum Quantity ●TLH/TLF Type Type TLH10UA TLH10UB TLF9UA□ TLF9UB□ Minimum Quantity［pcs］ Box 1000 500 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . coil_leaded_pack_e-E08R01 LEADED COMMON MODE CHOKE COILS FOR DC AND SIGNAL LINES， LEADED COMMON MODE CHOKE COILS FOR AC LINES ■RELIABILITY DATA 1. Operating Temperature Range Specified Value TLH, TLF Type －25～＋ 105℃ Test Method and Remarks Including temperature rise due to self－generated heat. 2. Storage temperature range Specified Value TLH, TLF Type －40～＋ 85℃ Specified Value TLH, TLF Type Within the specified range Test Method and Remarks TLH10U TLF9UA TLF9UB 3. Rated current : The maximum value of AC current within the temperature rise of 60℃ : The maximum value of AC current within the temperature rise of 45℃ : The maximum value of DC current within the temperature rise of 45℃ 4. Inductance Specified Value TLH, TLF Type Within the specified tolerance Test Method and Remarks TLF9U : Measuring equipment Measuring frequency Measuring voltage TLH、TLF（except TLF9U) : Measuring equipment Measuring frequency Measuring voltage : LCR meter 4284A or its equivalent : 1kHz : 1Vrms : LCR meter 4284A or its equivalent : 1kHz : 0.1Vrms 5. DC resistance Specified Value Test Method and Remarks TLH, TLF Type Within the specified tolerance Measuring equipment : DC ohmmeter 6. Terminal strength tensile force Specified Value Test Method and Remarks TLH, TLF Type No abnormality TLH10UA, TLH10UB, TLF9U : Apply the stated tensile force gradually in the direction to draw terminal. force [N] duration [s] 5 30±5 TLF (except TLF9U): Apply the stated tensile force gradually in the direction to draw terminal. force [N] duration [s] 10 30±5 7. Insulation resistance between wires Specified Value Test Method and Remarks TLH, TLF Type Applied voltage Duration 100MΩmin. : 500VDC (TLH, TLF (except TLF9UB)) : 250VDC (TLF9UB) : 60sec. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . coil_leaded_reli_e-E08R01 8. Insulation resistance between wire and core Specified Value Test Method and Remarks TLH, TLF Type TLF : Applied voltage Duration 100MΩ min.（except TLH） : 500VDC (TLF (except TLF9UB)) : 250VDC (TLF9UB) : 60 sec. 9. Withstanding : between wires Specified Value Test Method and Remarks TLH, TLF Type Applied voltage Duration No abnormality : 2000VAC (TLH, TLF (except TLF9UB)） : 500VDC (TLF9UB) : 60sec 10. Withstanding : between wires and core Specified Value Test Method and Remarks TLH, TLF Type TLF : Applied voltage Duration No abnormality（except TLH） : 2000VAC (TLF (except TLF9UB)) : 500VDC (TLF9UB) : 60sec. 11. Rated voltage Specified Value TLH, TLF Type Within the specified range Test Method and Remarks TLH, TLF (except TLF9UB) TLF9UB : 250VAC : 50VDC 12. Resistance to vibration TLF9U : Inductance change : Within ±5％ TLH, TLF (except TLF9U) : Appearance is no abnormality and within the specified range Specified Value TLH, TLF Type Test Method and Remarks TLH, TLF : According to JIS C60068-2-6. Direction : 2hrs each in X, Y and Z direction Total : 6hrs Frequency range : 10 to 55 to 10Hz (1 min.) Amplitude : 1.5mm (shall not exceed acceleration 196m/s2) Mounting method : soldering onto PC board Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. 13. Solderability Specified Value Test Method and Remarks TLH, TLF Type At least 90% of terminal electrode is covered by new solder. TLH, TLF : Solder temperature Duration Immersion depth : 235±0.5℃ : 2±0.5sec. : Up to 1.5 to 2.0mm from PBC mounted level. TLH, TLF : Solder temperature Duration Immersion depth : 245±5℃ : 4±1sec. : Up to 1.0 to 1.5mm from PBC mounted level. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . coil_leaded_reli_e-E08R01 14. Resistance to soldering heat Specified Value Test Method and Remarks TLH, TLF Type TLF9UA : Inductance change : Within ±5% TLH, TLF : Solder temperature Duration Immersion depth Recovery : : : : 260±5℃ 5±0.5sec. Up to 1.5 to 2.0mm from PBC mounted level. At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. TLH, TLF : Solder temperature Duration Immersion depth Recovery : : : : 260±5℃ 10±1sec. Up to 1.0 to 1.5mm from PBC mounted level. At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. 15. Thermal shock Specified Value Test Method and Remarks TLF9UA : Inductance change : Within ±15% TLH, TLF (except TLF9UA) : Withstanding voltage : No abnormality Insulation resistance : No abnormality TLH, TLF Type TLH, TLF : According to JIS C60068-2-14. Conditions for 1 cycle -25℃～+85℃、keep each 30min Number of cycles Recovery : 10 : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2 hrs. 16. Damp heat Specified Value TLH, TLF : Temperature Test Method and Remarks TLF9UA : Inductance change : Within ±15% TLH, TLF (except TLF9UA) : Withstanding voltage : No abnormality Insulation resistance : No abnormality TLH, TLF Type Humidity Duration Recovery : : : : : 60±2℃ 40±2℃ (※except TLF9U) 90～95％RH 500 hrs At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs. 17. Loading under damp heat Specified Value TLH, TLF : Temperature Test Method and Remarks Withstanding voltage : No abnormality Insulation resistance : No abnormality TLH, TLF Type Humidity Duration Applied voltage Recovery : : : : : : 60±2℃ 40±2℃ (※except TLF9U ) 90～95%RH 100 hrs 500 hrs Apply rated current across windings (※except TLF9U ) Apply the following specified voltage between windings. TLF9UA 250VAC TLF9UB 50VDC : At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . coil_leaded_reli_e-E08R01 18. Low temperature life test Specified Value Test Method and Remarks TLF9U : Inductance change : Within ±15% TLH, TLF (except TLF9U) : Withstanding voltage : No abnormality Insulation resistance : No abnormality TLH, TLF Type TLH, TLF : Temperature Duration Recovery : : : : －25±2℃ －40±2℃ (※TLF・TLH ) 500 hrs At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs. 19. High Temperature life test Specified Value TLH, TLF Type Test Method and Remarks TLH, TL F : Temperature Duration Recovery TLF9U : Inductance change : Within ±15% TLH, TLF (except TLF9U) : Withstanding voltage : No abnormality Insulation resistance : No abnormality : 105±3℃ (※ TLF・TLH) : 500 hrs : At least 1hr of recovery under the standard removal from test chamber followed by the measurement within 2 hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . coil_leaded_reli_e-E08R01 LEADED COMMON MODE CHOKE COILS FOR DC AND SIGNAL LINES， LEADED COMMON MODE CHOKE COILS FOR AC LINES ■PRECAUTIONS 1. Circuit Design Precautions ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Precautions Technical considerations ◆Design 1. Please design insertion pitches as matching to that of leads of the component on PCBs. ◆Design 1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs. 3. Soldering Precautions ◆Wave soldering 1. Please refer to the specifications in the catalog for a wave soldering. 2. Do not immerse the entire inductor in the flux during the soldering operation. ◆Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming of adhesion, temperature of resistance to soldering heat, etc. sufficiently. ◆Recommended conditions for using a soldering iron ・ Put the soldering iron on the land-pattern. ・ Soldering iron's temperature - Below 350℃ ・ Duration - 3 seconds or less ・ The soldering iron should not directly touch the product. Technical considerations ◆Lead free soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. ◆Recommended conditions for using a soldering iron If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. 4. Cleaning Precautions ◆Cleaning conditions 1. Please contact any of our offices for about a cleaning. 5. Handling Precautions Technical considerations ◆Handling 1. Keep the product away from all magnets and magnetic objects. ◆Mechanical considerations 1. Please do not give the product any excessive mechanical shocks. 2. Please do not add any shock or power to a product in transportation. ◆Packing 1. Please do not give the product any excessive mechanical shocks. In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item). ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 2. There is a case to be broken by a fall. ◆Packing 1. There is a case that a lead route turns at by a fall or an excessive shock. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . coil_leaded_prec_e-E08R01 6. Storage conditions Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : 0～40℃ Humidity : Below 70% RH The ambient temperature must be kept below 30℃. Even under ideal storage conditions, the solderbility of electrodes decreases gradually, so the products should be mounted within one year from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical considerations ◆Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . coil_leaded_prec_e-E08R01