YFF31AH2A104MT0Y0N

E M C C o m p o n e n t s January 2019 3-terminal filters For automotive large-current power line YFF-AH series YFF31AH 3216 [1206 inch]* Feed through filter * Dimensions Code JIS[EIA] (2/6) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using this products. REMINDERS Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and product temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in automotive electronic equipment under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment   (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20190115 / 3tf_automotive_power_yff-ah_en.fm (3/6) E M C C o m p o n e n t s Product compatible with RoHS directive Lead-free compatible 3-terminal filters For automotive large-current power line Overview of the YFF-AH series FEATURES Compact and high-performance EMC countermeasure components specialized for in-vehicle applications Also demonstrates an excellent effect for decoupling use Compliant with AEC-Q200 Good attenuation characteristic in wide bandwidth. Supports large current (6 to 10 A) APPLICATION EMC countermeasure and decoupling in power lines for various in-vehicle electronic equipment such as ECUs, car navigation systems, invehicle camera systems, millimeter wave radar systems, etc. PART NUMBER CONSTRUCTION YFF 31 AH 2A Series name LxW dimensions (mm) Product internal code Rated voltage (V) 31 3.2×1.6 AH For automotive large-current power line 2A 100 105 Capacitance (pF) 100,000 (0.1µF) 1,000,000 105 (1µF) 104 M T 0Y □ Tolerance Taping Internal code Reel size M ±20％ (mm) 0 ø178 9 ø330 N Internal electrode Ni PACKAGING STYLE AND SPECIFICATIONS Type YFF31AH Package quantity (piece/reel) ø178 2,000 ø330 10,000 Individual weight (g) 0.0342 RoHS Directive Compliant Product: See the following for more details. https://product.tdk.com/info/en/environment/rohs/index.html Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20190115 / 3tf_automotive_power_yff-ah_en.fm (4/6) E M C C o m p o n e n t s Overview of the YFF-AH series RECOMMENDED SOLDERING CONDITION REFLOW SOLDERING Soldering Preheating Slow cooling (Natural cooling) 150˚C max. Temperature(˚C) 260˚C max. 0 60 seconds or more 10s max. HAND SOLDERING PRECAUTIONS FOR HANDLING Before soldering, be sure to preheat components. The T preheating temperature must be 150°C max. with attention paid to thermal shock. Natural cooling of components in the air is recommended. On the other hand, when dipping them in a solvent for purposes, such as cleaning, make sure that the temperature difference (T) is 100°C. When performing hand soldering for circuit modification, apply the soldering iron to the copper foil area of the printed circuit board for 3 seconds or less. The temperature of the iron tip should not exceed 300°C. Use a wrist band to discharge static electricity in your body through the grounding wire. When incorporating the printed circuit board on which this product is mounted into a frame, etc., do not apply stress to the product through local bending of the board by tightening of screws, etc. 0 150˚C max. Temperature(˚C) 300 Preheating Make as short as possilble (within three seconds) Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20190115 / 3tf_automotive_power_yff-ah_en.fm (5/6) E M C C o m p o n e n t s YFF-AH series YFF31AH type (Feed through filter) SHAPE & DIMENSIONS 1.20±0.30 RECOMMENDED LAND PATTERN 1.40 0.10min. 0.80 0.90 1 IN/OUT 1.30 1.60±0.20 GND 4 3 OUT/IN Land pattern+Solder resist Land pattern 2 GND 3.20±0.20 2.50 Dimensions in mm 1.30±0.20 1.20 * Make sure to connect the GND terminal of this product and the GND of the mounting circuit board by using through holes so that the distance between them is the shortest. ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Insertion loss 40dB frequency range (MHz) Rated voltage Edc (V) 0.8 to 2000 100 0.8 to 2000 100 7 to 2000 100 7 to 2000 100 Operating temperature range (°C) Storage temperature range (After mount) (°C) Part No. –55 to +125 –55 to +125 YFF31AH2A105MT0Y0N –55 to +125 –55 to +125 YFF31AH2A105MT0Y9N –55 to +125 –55 to +125 YFF31AH2A104MT0Y0N –55 to +125 –55 to +125 YFF31AH2A104MT0Y9N The part numbers are TDK’s standard specification products. INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 10 2A104M 10 Rated Current(A) 20 30 40 50 ELECTRICAL CURRENT RATING DERATING 12 0 Insertion Loss(dB)  Rated current Idc (A) DC6A/105°C DC4A/125°C DC6A/105°C DC4A/125°C DC10A/105°C DC6A/125°C DC10A/105°C DC6A/125°C 2A105M 60 70 2A104 8 6 2A105 4 2 80 90 0.1 1 10 100 Frequency (MHz) 1000 10000 0 –55 –35 –15 5 25 45 65 85 Ambient temperature(°C) 105 125 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20190115 / 3tf_automotive_power_yff-ah_en.fm (6/6) E M C C o m p o n e n t s YFF-AH series Packaging style REEL DIMENSIONS C B E r W D t A Unit: mm Reel ø178 ø330 A ø178±2.0 ø382 max.(ø330 nom.) B ø60±2.0 ø50 min. C ø13±0.5 ø13±0.5 D ø21±0.8 ø21±0.8 E 2.0±0.5 2.0±0.5 W 9.0±0.3 10.0±1.5 t 2.0±0.5 2.0±0.5 r 1.0 1.0 TAPE DIMENSIONS Plastic tape J Square punch hole for component mounting D B C E Round sprocket holes t A H G F Q K Unit: mm Type YFF31AH A 1.9 typ. B 3.5 typ. C 8.0±0.3 D 3.5±0.05 E 1.75±0.1 F 4.0±0.1 G 2.0±0.05 H 4.0±0.1 J ø1.5+0.1/–0 K 2.5 max. t 0.3 max. Q ø0.5 min. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20190115 / 3tf_automotive_power_yff-ah_en.fm