TSOP14240

TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., TSOP146.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES • Improved dark sensitivity • Improved immunity against optical noise • Improved immunity against Wi-Fi noise • • • • • • 1 2 16672 LINKS TO ADDITIONAL RESOURCES 3D 3D Product Page Holders 3D Models Calculators Marking MECHANICAL DATA Packages Pinning for TSOP14...: 1 = OUT, 2 = GND, 3 = VS Pinning for TSOP12...: 1 = OUT, 2 = VS, 3 = GND Bends and Cuts DESCRIPTION ORDERING CODE The TSOP12... and TSOP14... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems. These series provide improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. The robustness against spurious pulses originating from Wi-Fi signals has been enhanced. TSOP12..., TSOP14... - 2160 pieces in tubes BLOCK DIAGRAM VS 30 kΩ The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. OUT Input The TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., and TSOP146.. series devices are designed to receive long burst codes (10 or more carrier cycles per burst). The third digit designates the AGC level (AGC2, AGC4, or AGC6) and the last two digits designate the band-pass frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC2 provides basic noise suppression, AGC4 provides enhanced noise suppression and AGC6 provides maximized noise suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code. Band pass AGC Demodulator GND PIN Control circuit 16833-22 APPLICATION CIRCUIT 17170-11 Transmitter with TSALxxxx These components have not been qualified to automotive specifications. R1 IR receiver VS Circuit 3 Low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Insensitive to supply voltage ripple and noise Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 + VS C1 μC OUT GND VO GND R1 and C1 recommended to reduce supply ripple for VS < 2.8 V Rev. 1.9, 14-Dec-2021 1 Document Number: 82803 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., TSOP146.. www.vishay.com Vishay Semiconductors PARTS TABLE BASIC NOISE SUPPRESSION (AGC2) AGC Carrier frequency ENHANCED NOISE SUPPRESSION (AGC4) MAXIMIZED NOISE SUPPRESSION (AGC6) 30 kHz TSOP14230 TSOP12230 TSOP14430 TSOP12430 TSOP14630 33 kHz TSOP14233 TSOP12233 TSOP14433 TSOP12433 TSOP14633 TSOP12633 36 kHz TSOP14236 TSOP12236 TSOP14436 (2)(5)(7) TSOP12436 (2)(5)(7) TSOP14636 (6) TSOP12636 (6) TSOP14238 TSOP12238 TSOP14638 TSOP12638 38 kHz 40 kHz TSOP14240 (12) TSOP12240 (12) 56 kHz TSOP14256 (1) TSOP14438 (3)(4)(10)(11) TSOP12438 (3)(4)(10)(11) TSOP12256 (1) TSOP14440 TSOP12440 TSOP14640 TSOP12640 TSOP14456 (9) TSOP12456 (9) TSOP14656 (8) TSOP12656 (8) Package Pinning Mold 1 = OUT, 1 = OUT, 2 = GND, 3 = VS 2 = VS, 3 = GND 1 = OUT, 2 = VS, 3 = GND 1 = OUT, 2 = GND, 3 = VS Dimensions (mm) 1 = OUT, 1 = OUT, 2 = GND, 3 = VS 2 = VS, 3 = GND 6.0 W x 6.95 H x 5.6 D Mounting Leaded Application Remote control (1) Best choice for Special options TSOP12630 Cisco (2) MCIR (3) Mitsubishi (4) NEC (5) Panasonic (6) RC-5 (7) (8) RCA (9) r-step (10) Sejin 4PPM (11) Sharp (12) Sony RC-6 • Narrow optical filter: www.vishay.com/doc?81590 • Wide optical filter: www.vishay.com/doc?82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT VS -0.3 to +6 V mA Supply voltage Supply current IS 3 Output voltage VO -0.3 to (VS + 0.3) V Output current IO 5 mA Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature Tj 100 °C Tstg -25 to +85 °C Tamb -25 to +85 °C Tamb ≤ 85 °C Ptot 10 mW t ≤ 10 s, 1 mm from case Tsd 260 °C Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER Supply current TEST CONDITION SYMBOL MIN. TYP. MAX. Ev = 0, VS = 3.3 V ISD 0.55 0.7 0.9 mA Ev = 40 klx, sunlight ISH - 0.8 - mA VS 2.5 - 5.5 V d - 30 - m VOSL - - 100 mV Supply voltage Transmission distance Output voltage low Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA mW/m2, IOSL = 0.5 mA, Ee = 0.7 test signal see Fig. 1 UNIT Minimum irradiance Pulse width tolerance: tpi - 3.5/f0 < tpo < tpi + 3.5/f0, test signal see Fig. 1 Ee min. - 0.08 0.15 mW/m2 Maximum irradiance tpi - 3.5/f0 < tpo < tpi + 3.5/f0, test signal see Fig. 1 Ee max. 30 - - W/m2 Angle of half transmission distance ϕ1/2 - ± 45 - ° Directivity Rev. 1.9, 14-Dec-2021 2 Document Number: 82803 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., TSOP146.. www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Axis Title Optical Test Signal (IR diode TSAL6200, IF = 0.1 A, 30 pulses, f = f0, t = 10 ms) (1) VO VOH VOL (1) T AGC4: tpi ≥ 10/f0, AGC2, AGC6: tpi ≥ 19/f0 Output Signal (2) AGC4: 8/f0 < td < 14/f0 AGC2, AGC 6: 14/f0 < td < 20/f0 (3) tpi - 3.5/f0 < tpo < tpi + 3.5/f0 td (2) 16110-15 ton 0.7 0.6 1000 0.5 toff 1st line 2nd line t tpi 10000 0.8 2nd line ton, toff - Output Pulse Width (ms) Ee 0.4 0.3 100 0.2 0.1 λ = 950 nm, optical test signal, Fig. 3 0 tpo (3) 0.1 t 1 10 100 1000 10 10 000 Ee - Irradiance (mW/m2) Fig. 4 - Pulse-Width vs. Irradiance in Dark Ambient Fig. 1 - Output Delay and Pulse-Width Axis Title Axis Title 10000 Output pulse width 1000 1st line 2nd line 0.80 Input burst length 0.70 100 0.60 λ = 950 nm, optical test signal, Fig. 1 10 0.50 0.1 0.6 100 0.4 f = f0 ± 5 % 0.2 10 0 0.7 0.9 1.1 1.3 Ee - Irradiance (mW/m2) f/f0 - Relative Frequency Fig. 2 - Pulse-Width vs. Irradiance in Dark Ambient Fig. 5 - Frequency Dependence of Responsivity Axis Title Optical Test Signal t 600 µs t = 60 ms 94 8134 Output Signal, (see Fig. 4) VOH VOL t on t off Correlation with ambient light sources: 10 W/m2 = 1.4 klx (std. ilum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) 2 Wavelength of ambient illumination: λ = 950 nm 1000 100 1 0 0.01 t 10 0.1 1 10 100 Ee - Ambient DC Irradiance (W/m2) Fig. 6 - Sensitivity in Bright Ambient Fig. 3 - Test Signal Rev. 1.9, 14-Dec-2021 10000 3 1st line 2nd line 600 µs VO 1000 0.8 1000 2nd line Ee min. - Threshold Irradiance (mW/m2) Ee 10 1.0 1st line 2nd line 0.90 10000 1.2 2nd line Ee min./Ee - Relative Responsivity 2nd line tpo - Output Pulse Width (ms) 1.00 3 Document Number: 82803 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., TSOP146.. www.vishay.com Vishay Semiconductors Axis Title Axis Title 10000 0.7 0.6 1000 0.5 f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 0.4 0.3 100 0.2 0.1 10 1000 0 1 10 100 10000 0.9 0.8 0.7 1000 0.6 1st line 2nd line 2nd line S(λ)rel. - Relative Spectral Sensitivity 1.0 1st line 2nd line 0.5 0.4 100 0.3 0.2 0.1 0 750 850 950 10 1150 ∆VS RMS - AC Voltage on DC Supply Voltage (mV) λ - Wavelength (nm) Fig. 7 - Sensitivity vs. Supply Voltage Disturbances Fig. 10 - Relative Spectral Sensitivity vs. Wavelength Axis Title Axis0° Title 10° 1.0 20° 30° 10000 f = 38 kHz, Ee = 2 mW/m2 0.9 0.8 0.7 0.5 TSOP146.., TSOP126.. 0.4 2nd line 2nd line 0.6 40° 1.0 1000 TSOP142.., TSOP122.. 1st line 2nd line 2nd line Maximum Envelope Duty Cycle 1050 0.9 50° 0.8 60° 100 0.3 TSOP144.., TSOP124.. 0.2 70° 0.7 80° 0.1 10 0 0 20 40 60 80 100 120 0.6 140 0.4 0.2 0 0.2 0.4 Burst Length (Number of Cycles/Burst) drel. - Relative Transmission Distance Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length Fig. 11 - Directivity Axis Title 0.20 0.15 1st line 2nd line 1000 0.10 100 0.05 10 0 -10 10 30 50 70 10000 0.15 1000 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 10000 -30 0.6 Axis Title 0.20 2nd line Ee min. - Threshold Irradiance (mW/m2) 2nd line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 0.8 0.10 100 0.05 10 0 90 1.5 2.5 3.5 4.5 5.5 Tamb - Ambient Temperature (°C) VS - Supply Voltage (V) Fig. 9 - Sensitivity vs. Ambient Temperature Fig. 12 - Sensitivity vs. Supply Voltage Rev. 1.9, 14-Dec-2021 4 Document Number: 82803 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., TSOP146.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. 10000 7 When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver’s output. Some examples which are suppressed are: 5 1000 1st line 2nd line 2nd line IR Signal Amplitude 6 4 3 100 2 1 • DC light (e.g. from tungsten bulbs sunlight) 10 0 0 • Continuous signals at any frequency 5 15 20 Time (ms) 16920 • Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 13 or Fig. 14) 10 Fig. 13 - IR Emission from Fluorescent Lamp With Low Modulation • 2.4 GHz and 5 GHz Wi-Fi Axis Title 10000 40 1000 0 1st line 2nd line 2nd line IR Signal Amplitude 20 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 14 - IR Emission from Fluorescent Lamp With High Modulation TSOP122.., TSOP142.. TSOP124.., TSOP144.. TSOP126.., TSOP146.. Minimum burst length 19 cycles/burst 10 cycles/burst 19 cycles/burst After each burst of length a minimum gap time is required of 19 to 85 cycles ≥ 19 cycles 10 to 40 cycles ≥ 12 cycles 19 to 50 cycles ≥ 19 cycles 85 cycles > 6 x burst length 40 cycles > 10 x burst length 50 cycles > 10 x burst length For bursts greater than a minimum gap time in the data stream is needed of Maximum number of continuous short bursts/second 800 1300 800 RC-5 code Yes Preferred Preferred RC-6 code Yes Preferred Yes NEC code Yes Preferred Yes r-step code Yes Preferred Yes Sony code Preferred No No Yes Yes Preferred Fig. 13 Fig. 13 and Fig. 14 Fig. 13 and Fig. 14 RCA 56 kHz code Suppression of interference from fluorescent lamps Note • For data formats with short bursts please see the datasheet for TSOP121.., TSOP123.., TSOP125.., TSOP141.., TSOP143.., TSOP145.. Rev. 1.9, 14-Dec-2021 5 Document Number: 82803 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., TSOP146.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 3.9 1 1 30.5 ± 0.5 (5.55) 8.25 6.95 5.3 6 0.85 max. 0.89 0.5 max. 2.54 nom. 1.3 0.7 max. 4.1 2.54 nom. 5.6 marking area Not indicated tolerances ± 0.2 technical drawings according to DIN specifications R 2.5 Drawing-No.: 6.550-5169.01-4 Issue: 9; 03.11.10 13655 Rev. 1.9, 14-Dec-2021 6 Document Number: 82803 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 09-Jul-2021 1 Document Number: 91000