TSOP33536

TSOP331.., TSOP333.., TSOP335.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES • Very low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Supply voltage: 2.5 V to 5.5 V • Improved immunity against ambient light • Insensitive to supply voltage ripple and noise • Compatible with wave or reflow soldering (see “P” version of Minimold option datasheets) • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 23051 MECHANICAL DATA LINKS TO ADDITIONAL RESOURCES Pinning for TSOP33...: 3D 3D Product Page 3D Models Holders Bends and Cuts Calculators Marking 1 = OUT, 2 = GND, 3 = VS Packages ORDERING CODE TSOP33... - 1800 pieces in bags DESCRIPTION BLOCK DIAGRAM The TSOP33... series are miniaturized IR receiver modules for infrared remote control systems. A PIN diode and a preamplifier are assembled on lead frame, the epoxy package contains an IR filter. 16833-13 3 30 kΩ The demodulated output signal can be directly connected to a microprocessor for decoding. 1 Input The TSOP333.. series devices are optimized to suppress almost all spurious pulses from energy saving lamps like CFLs. AGC3 may also suppress some data signals if continuously transmitted. Band pass AGC Demodulator 2 PIN The TSOP331.. series are provided primarily for compatibility with old AGC1 designs. New designs should prefer the TSOP333.. series containing the newer AGC3. The TSOP335.. series contain a very robust AGC5. This series should only be used for critically noisy environments. Control circuit APPLICATION CIRCUIT 17170-11 Transmitter with TSALxxxx R1 IR receiver VS Circuit These components have not been qualified according to automotive specifications. + VS C1 μC OUT GND VO GND R1 and C1 recommended to reduce supply ripple for VS < 2.8 V Rev. 1.6, 05-Aug-2021 1 Document Number: 82742 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP331.., TSOP333.., TSOP335.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR SHORT BURSTS (AGC1) AGC Carrier frequency FOR SHORT BURSTS, NOISY FOR SHORT BURSTS, VERY ENVIRONMENTS (AGC3) NOISY ENVIRONMENTS (AGC5) 30 kHz TSOP33130 TSOP33330 TSOP33530 33 kHz TSOP33133 TSOP33333 TSOP33533 36 kHz TSOP33136 TSOP33336 (1)(2)(7) TSOP33536 38 kHz TSOP33138 TSOP33338 (3)(4)(5)(6) TSOP33538 40 kHz TSOP33140 TSOP33340 TSOP33540 56 kHz TSOP33156 TSOP33356 TSOP33556 Package Minimold Pinning 1 = OUT, 2 = GND, 3 = VS Dimensions (mm) 5.4 W x 6.35 H x 4.9 D Mounting Leaded Application Best choice for Special options Remote control (1) MCIR (2) RCMM (3) Mitsubishi (4) RECS-80 Code (5) r-map (6) XMP-1, XMP-2 (7) RCMM • Narrow optical filter: www.vishay.com/doc?81590 • Wide optical filter: www.vishay.com/doc?82726 • Low voltage option: www.vishay.com/doc?82382 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT VS -0.3 to +6 V mA Supply voltage Supply current IS 3 Output voltage VO -0.3 to (VS + 0.3) V Output current IO 5 mA Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature Tj 100 °C Tstg -25 to +85 °C Tamb -25 to +85 °C Tamb ≤ 85 °C Ptot 10 mW t ≤ 10 s, 1 mm from case Tsd 260 °C Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER Supply current TEST CONDITION SYMBOL MIN. TYP. MAX. Ev = 0, VS = 3.3 V ISD 0.27 0.35 0.45 mA Ev = 40 klx, sunlight ISH - 0.45 - mA VS 2.5 - 5.5 V d - 30 - m VOSL - - 100 mV Supply voltage Transmission distance Output voltage low Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA mW/m2, IOSL = 0.5 mA, Ee = 0.7 test signal see Fig. 1 UNIT Minimum irradiance Pulse width tolerance: tpi - 5/f0 < tpo < tpi + 6/f0, test signal see Fig. 1 Ee min. - 0.08 0.15 mW/m2 Maximum irradiance tpi - 5/f0 < tpo < tpi + 6/f0, test signal see Fig. 1 Ee max. 30 - - W/m2 Directivity Angle of half transmission distance ϕ1/2 - ± 45 - ° Rev. 1.6, 05-Aug-2021 2 Document Number: 82742 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP331.., TSOP333.., TSOP335.. www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms) 0.8 t tpi *) T *) tpi ≥ 6/f0 is recommended for optimal function Output Signal VO 1) 2) VOH VOL td 14337 3/f0 < td < 9/f0 tpi - 4/f0 < tpo < tpi + 6/f0 1) tpo ton ton, toff - Output Pulse Width (ms) Ee 0.7 0.6 0.5 toff 0.4 0.3 0.2 λ = 950 nm, optical test signal, fig. 3 0.1 0 0.1 20744 t 2) Ee min./Ee - Relative Responsivity tpo - Output Pulse Width (ms) 0.35 0.30 Output pulse width 0.20 0.15 Input burst length 0.10 λ = 950 nm, optical test signal, Fig. 1 10 000 1.0 0.8 0.6 0.4 f = f0 ± 5 % Δf(3 dB) = f0/10 0.2 0.0 1 10 100 1000 10 000 0.7 Ee - Irradiance (mW/m²) 20760 Ee min. - Threshold Irradiance (mW/m²) t 600 µs t = 60 ms 94 8134 Output Signal, (see Fig. 4) VOH VOL t on t off 1.3 4.0 Correlation with ambient light sources: 3.5 10 W/m² = 1.4 klx (std. illum. A, T = 2855 K) 10 W/m² = 8.2 klx (daylight, T = 5900 K) 3.0 2.5 1.5 1.0 0.5 0 0.01 t Fig. 3 - Output Function Wavelength of ambient illumination: λ = 950 nm 2.0 20745 Rev. 1.6, 05-Aug-2021 1.1 Fig. 5 - Frequency Dependence of Responsivity Optical Test Signal 600 µs 0.9 f/f0 - Relative Frequency 16925 Fig. 2 - Pulse Length and Sensitivity in Dark Ambient VO 1000 1.2 0 0.1 Ee 100 Fig. 4 - Output Pulse Diagram 0.40 0.05 10 Ee - Irradiance (mW/m²) Fig. 1 - Output Active Low 0.25 1 0.1 1 10 100 Ee - Ambient DC Irradiance (W/m²) Fig. 6 - Sensitivity in Bright Ambient 3 Document Number: 82742 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP331.., TSOP333.., TSOP335.. www.vishay.com Vishay Semiconductors 1.0 2.0 f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 1.5 1.0 0.5 0 1 10 100 0.8 0.7 1000 0.6 1st line 2nd line 2.5 10000 0.9 2nd line S(λ)rel. - Relative Spectral Sensitivity Ee min. - Threshold Irradiance (mW/m2) Axis Title 3.0 0.5 0.4 100 0.3 0.2 0.1 1000 0 750 ΔVS RMS - AC Voltage on DC Supply Voltage (mV) 850 950 1050 10 1150 λ - Wavelength (nm) 23180 Fig. 10 - Relative Spectral Sensitivity vs. Wavelength Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 0° 10° 20° 1.0 30° f = 38 kHz, Ee = 2 mW/m² Max. Envelope Duty Cycle 0.9 0.8 0.7 40° TSOP331.. 0.6 1.0 0.5 0.9 50° 0.8 60° 0.4 0.3 TSOP333.. 0.2 70° 0.7 80° 0.1 TSOP335.. 0 0 20 40 60 80 100 0.6 120 0.2 0 Fig. 11 - Horizontal Directivity Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length 0.20 0.20 0.18 0.16 Ee min. - Sensitivity (mW/m2) Ee min. - Threshold Irradiance (mW/m2) 0.4 drel - Relative Transmission Distance Burst Length (Number of Cycles/Burst) 0.14 0.12 0.10 0.08 0.06 0.04 0.02 0 -30 -10 10 30 50 70 0.18 0.16 0.14 0.12 0.10 0.08 0.06 0.04 0.02 0.00 90 1 Tamb - Ambient Temperature (°C) 2 3 4 5 VS - Supply Voltage (V) Fig. 9 - Sensitivity vs. Ambient Temperature Fig. 12 - Sensitivity vs. Supply Voltage Rev. 1.6, 05-Aug-2021 4 Document Number: 82742 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP331.., TSOP333.., TSOP335.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. 10000 7 When a data signal presented to the device in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver’s output. Some examples which are suppressed are: 5 1000 1st line 2nd line 2nd line IR Signal Amplitude 6 4 3 100 2 1 • DC light (e.g. from tungsten bulbs sunlight) 10 0 0 • Continuous signals at any frequency 5 15 20 Time (ms) 16920 • Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 13 or Fig. 14). 10 Fig. 13 - IR Disturbance from Fluorescent Lamp With Low Modulation Axis Title 10000 40 1000 0 1st line 2nd line 2nd line IR Signal Amplitude 20 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 14 - IR Disturbance from Fluorescent Lamp With High Modulation TSOP331.. TSOP333.. TSOP335.. Minimum burst length 6 cycles/burst 6 cycles/burst 6 cycles/burst After each burst of length A gap time is required of 6 to 70 cycles ≥ 10 cycles 6 to 35 cycles ≥ 10 cycles 6 to 24 cycles ≥ 10 cycles 70 cycles 35 cycles 24 cycles > 1.2 x burst length > 6 x burst length > 25 ms 2000 2000 2000 Yes For bursts greater than a minimum gap time in the data stream is needed of Maximum number of continuous short bursts/second MCIR code Yes Preferred RCMM code Yes Preferred Yes XMP-1, XMP-2 code Yes Preferred Yes Mild disturbance patterns are suppressed (example: signal pattern of Fig. 13) Complex disturbance patterns are suppressed (example: signal pattern of Fig. 14) Critical disturbance patterns are suppressed, e.g. highly dimmed LCDs Suppression of interference from fluorescent lamps Note • For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP332.., TSOP334.. Rev. 1.6, 05-Aug-2021 5 Document Number: 82742 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP331.., TSOP333.., TSOP335.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 5 Cavity number Marking area 5.4 R2.5 15.2 ± 0.3 (0.95) (5.05) 7.6 6.35 2.25 (1.1) (3 x) 0.85 max. 0.95 1 2 3 (3 x) 0.6 ± 0.1 (3 x) 0.3 ± 0.1 2.54 nom. 2.54 nom. Technical drawings according to DIN specifications R2.5 Not indicated tolerances ± 0.2 Drawing-No.: 6.550-5335.01-4 Issue: 2; 02.07.19 Rev. 1.6, 05-Aug-2021 6 Document Number: 82742 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP331.., TSOP333.., TSOP335.. www.vishay.com Vishay Semiconductors BULK PACKAGING Standard shipping for minimold is in conductive plastic bags. The packing quantity is determined by weight and a maximum of 0.3 % of the components per carton may be missing. ORDERING INFORMATION T S P O = receiver S = sensor d d IC and package type d AGC d d Frequency Note • d = “digit”, please consult the list of available series on the previous page to create a valid part number Examples: TSOP33338 TSOP33356VI1 TSOP33338SS1F PACKAGING QUANTITY • 300 pieces per bag (each bag is individually boxed) • 6 bags per carton Rev. 1.6, 05-Aug-2021 7 Document Number: 82742 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000