TSOP93338

TSOP931.., TSOP933.., TSOP935.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES • Improved dark sensitivity • Improved immunity against optical noise • Very low supply current • • • • • Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.0 V to 3.6 V Insensitive to supply voltage ripple and noise Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 23051 LINKS TO ADDITIONAL RESOURCES MECHANICAL DATA 3D 3D Product Page 3D Models 1 = OUT, 2 = GND, 3 = VS Calculators Marking Packages ORDERING CODE TSOP93... - 1800 pieces in bags Bends and Cuts BLOCK DIAGRAM DESCRIPTION 16833-13 The TSOP93... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems. These series provide improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. 3 30 kΩ 1 Input The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. Band pass AGC Demodulator 2 PIN The TSOP931.., TSOP933.., and TSOP935.., series devices are designed to receive short burst codes (6 or more carrier cycles per burst). The third digit designates the AGC level (AGC1, AGC3, or AGC5) and the last two digits designate the band-pass frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC3 provides enhanced noise suppression and AGC5 provides maximized noise suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code. Control circuit APPLICATION CIRCUIT 17170-12 Transmitter with TSALxxxx These components have not been qualified to automotive specifications. R1 IR receiver VS Circuit Holders + VS C1 μC OUT GND VO GND R1 and C1 recommended to reduce supply ripple for VS < 2.2 V Rev. 1.5, 30-Jul-2021 1 Document Number: 82840 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP931.., TSOP933.., TSOP935.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR SHORT BURSTS (AGC1) AGC Carrier frequency ENHANCED NOISE SUPPRESSION MAXIMIZED NOISE SUPPRESSION (AGC3) (AGC5) 30 kHz TSOP93130 TSOP93330 33 kHz TSOP93133 TSOP93333 TSOP93530 TSOP93533 36 kHz TSOP93136 TSOP93336 (1)(5) TSOP93536 38 kHz TSOP93138 TSOP93338 (2)(4) TSOP93538 40 kHz TSOP93140 TSOP93340 TSOP93540 56 kHz TSOP93156 TSOP93356 TSOP93556 (3) Package Minimold Pinning 1 = OUT, 2 = GND, 3 = VS Dimensions (mm) 5.4 W x 6.35 H x 4.9 D Mounting Leaded Application Remote control (1) Best choice for Special options RCMM (2) RECS-80 Code (3) r-map (4) XMP-1, XMP-2 (5) MCIR • Narrow optical filter: www.vishay.com/doc?81590 • Wide optical flter: www.vishay.com/doc?82726 Note • 30 kHz and 33 kHz only available on written request ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL VALUE Supply voltage TEST CONDITION VS -0.3 to +3.6 UNIT V Supply current IS 3 mA Output voltage VO -0.3 to (VS + 0.3) V Output current IO 5 mA Junction temperature Tj 100 °C Storage temperature range Tstg -25 to +85 °C Operating temperature range Tamb -25 to +85 °C Tamb ≤ 85 °C Ptot 10 mW t ≤ 10 s, 1 mm from case Tsd 260 °C Power consumption Soldering temperature Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER Supply current TEST CONDITION SYMBOL MIN. TYP. MAX. Ev = 0, VS = 3.3 V ISD 0.25 0.37 0.45 mA Ev = 40 klx, sunlight ISH - 0.50 - mA Supply voltage UNIT VS 2.0 - 3.6 V Transmission distance Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA d - 28 - m Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 VOSL - - 100 mV Minimum irradiance Maximum irradiance Directivity Rev. 1.5, 30-Jul-2021 Test signal: XMP code Ee min. Test signal: NEC code - 0.12 0.25 - 0.09 0.20 mW/m2 tpi - 3.0/f0 < tpo < tpi + 3.5/f0, test signal see Fig. 1 Ee max. 30 - - W/m2 Angle of half transmission distance ϕ1/2 - ± 45 - ° 2 Document Number: 82840 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP931.., TSOP933.., TSOP935.. www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Axis Title Optical Test Signal (IR diode TSAL6200, N = 6 pulses, f = f0, T = 10 ms) Ee 1.0 10000 t tpi (1) T (1) tpi ≥ 6/f0 Output Signal VO (2) (3) VOH 4/f0 < td < 10/f0 tpi - 3.0/f0 < tpo < tpi + 3.5/f0 0.8 ton 0.7 1000 0.6 0.5 1st line 2nd line 2nd line ton, toff - Output Pulse Width (ms) 0.9 toff 0.4 100 0.3 0.2 λ = 950 nm, optical test signal, Fig. 3 0.1 10 10 000 100 000 0 VOL td (2) 0.1 t tpo (3) 1 10 Fig. 4 - Pulse-Width vs. Irradiance in Dark Ambient Fig. 1 - Output Delay and Pulse-Width Axis Title Axis Title 10000 1st line 2nd line 0.15 Input burst length 100 0.10 λ = 950 nm, optical test signal, Fig. 1 10 100 000 0 0.1 1000 0.6 100 0.4 f = f0 ± 5 % ∆f (3 dB) = f0/10 0.2 10 0 0.7 0.9 1.1 1.3 Ee - Irradiance (mW/m2) f/f0 - Relative Frequency Fig. 2 - Pulse-Width vs. Irradiance in Dark Ambient Fig. 5 - Frequency Dependence of Responsivity Axis Title Optical Test Signal 600 µs 4 t 600 µs t = 60 ms VO 1000 0.8 94 8134 Output Signal, (see Fig. 4) VOH VOL t on t off 3 Wavelength of ambient illumination: λ = 950 nm 1000 2 100 1 0 0.01 t 10 0.1 1 10 100 Ee - Ambient DC Irradiance (W/m2) Fig. 6 - Sensitivity in Bright Ambient Fig. 3 - Test Signal Rev. 1.5, 30-Jul-2021 10000 Correlation with ambient light sources: 10 W/m2 = 1.4 klx (std. ilum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) 1st line 2nd line Ee 10 1.0 1st line 2nd line 1000 2nd line Ee min. - Threshold Irradiance (mW/m2) 2nd line tpo - Output Pulse Width (ms) Output pulse width 0.20 10000 1.2 2nd line Ee min./Ee - Relative Responsivity 0.30 0.05 1000 Ee - Irradiance (mW/m2) 14337-5 0.25 100 3 Document Number: 82840 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP931.., TSOP933.., TSOP935.. www.vishay.com Vishay Semiconductors Axis Title Axis Title 10000 1.0 0.8 f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 0.7 0.6 0.5 1000 0.4 100 0.3 0.2 0.1 10 1000 0 1 10 100 10000 0.9 0.8 0.7 1000 0.6 1st line 2nd line 2nd line S(λ)rel. - Relative Spectral Sensitivity 0.9 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 1.0 0.5 0.4 100 0.3 0.2 0.1 0 750 850 950 1050 10 1150 ∆VS RMS - AC Voltage on DC Supply Voltage (mV) λ - Wavelength (nm) Fig. 7 - Sensitivity vs. Supply Voltage Disturbances Fig. 10 - Relative Spectral Sensitivity vs. Wavelength Axis Title 1.0 f = 38 kHz, Ee = 2 Axis0° Title 10° 20° 30° 10000 mW/m2 0.8 0.6 0.4 2nd line 2nd line TSOP931.. 0.5 40° 1.0 1000 0.9 50° 0.8 60° 100 0.3 TSOP933.. 70° 0.7 0.2 0.1 80° TSOP935.. 10 0 0 20 40 60 80 100 120 0.6 140 0.4 0.2 0 0.2 0.4 Burst Length (Number of Cycles/Burst) drel. - Relative Transmission Distance Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length Fig. 11 - Directivity 10000 1st line 2nd line 0.15 100 0.10 0.05 10 0 -10 10 30 50 70 0.25 1000 0.20 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 1000 0.20 10000 0.30 0.25 -30 0.6 Axis Title Axis Title 0.30 2nd line Ee min. - Threshold Irradiance (mW/m2) 2nd line 2nd line 0.7 1st line 2nd line 2nd line Maximum Envelope Duty Cycle 0.9 0.15 100 0.10 0.05 10 0 1.0 90 1.5 2.0 2.5 3.0 3.5 4.0 Tamb - Ambient Temperature (°C) VS - Supply Voltage (V) Fig. 9 - Sensitivity vs. Ambient Temperature Fig. 12 - Sensitivity vs. Supply Voltage Rev. 1.5, 30-Jul-2021 4 Document Number: 82840 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP931.., TSOP933.., TSOP935.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. 10000 7 When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver’s output. Some examples which are suppressed are: 5 1000 1st line 2nd line 2nd line IR Signal Amplitude 6 4 3 100 2 1 • DC light (e.g. from tungsten bulbs sunlight) 10 0 0 • Continuous signals at any frequency 5 15 20 Time (ms) 16920 • Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 13 or Fig. 14) 10 Fig. 13 - IR Emission from Fluorescent Lamp With Low Modulation Axis Title 10000 40 1000 0 1st line 2nd line 2nd line IR Signal Amplitude 20 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 14 - IR Emission from Fluorescent Lamp With High Modulation TSOP931.. TSOP933.. TSOP935.. Minimum burst length 6 cycles/burst 6 cycles/burst 6 cycles/burst After each burst of length A gap time is required of 6 to 70 cycles ≥ 6 cycles 6 to 20 cycles ≥ 8 cycles 6 to 38 cycles ≥ 8 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 1 x burst length 20 cycles > 6 x burst length 38 cycles > 20 ms 2500 Maximum number of continuous short bursts/second 3000 2500 RCMM code Yes Preferred Yes XMP-1 code Yes Preferred Yes Preferred r-map code Yes Yes RECS-80 code Yes Preferred Yes MCIR Yes Preferred Yes Fig. 13 Fig. 13 and Fig. 14 Fig. 13 and Fig. 14 Suppression of interference from fluorescent lamps Note • For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP932.., TSOP934.., or TSOP936.. Rev. 1.5, 30-Jul-2021 5 Document Number: 82840 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP931.., TSOP933.., TSOP935.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 5 Cavity number Marking area 5.4 R2.5 15.2 ± 0.3 (0.95) (5.05) 7.6 6.35 2.25 (1.1) (3 x) 0.85 max. 0.95 1 2 3 (3 x) 0.6 ± 0.1 (3 x) 0.3 ± 0.1 2.54 nom. 2.54 nom. Technical drawings according to DIN specifications R2.5 Not indicated tolerances ± 0.2 Drawing-No.: 6.550-5335.01-4 Issue: 2; 02.07.19 Rev. 1.5, 30-Jul-2021 6 Document Number: 82840 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP931.., TSOP933.., TSOP935.. www.vishay.com Vishay Semiconductors BULK PACKAGING Standard shipping for minimold is in conductive plastic bags. The packing quantity is determined by weight and the number of components per carton may vary by a maximum of ± 0.3 %. ORDERING INFORMATION Examples: TSOP93338 TSOP93356VI1 TSOP93338SS1F For more information, see: www.vishay.com/doc?80076 PACKAGING QUANTITY • 300 pieces per bag (each bag is individually boxed) • 6 bags per carton Rev. 1.5, 30-Jul-2021 7 Document Number: 82840 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000