VS-VSMD400CW60

VS-VSMD400AW60, VS-VSMD400CW60 www.vishay.com Vishay Semiconductors Standard Recovery Diodes, 400 A FEATURES • Standard rectifier • Popular series for rough service • Cathode and anode to base available • UL approved file E222165 • Designed and qualified for industrial level • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 TO-244 TYPICAL APPLICATIONS • Welders PRIMARY CHARACTERISTICS IF(AV) per module 400 A Type Modules - diode, high voltage Package TO-244 Circuit configuration Two diodes common anode, two diodes common cathode • Power supplies • Motor controls • Battery chargers • General industrial current rectification MAJOR RATINGS AND CHARACTERISTICS SYMBOL CHARACTERISTICS IF(AV) TC IF(RMS) VALUES UNITS 400 A 133 °C 628 IFSM I2t 50 Hz 2500 60 Hz 2620 50 Hz 31 60 Hz 28 I2t 312 VRRM TStg, TJ A kA2s kA2s 600 V -40 to +175 °C ELECTRICAL SPECIFICATIONS VOLTAGE RATINGS TYPE NUMBER VS-VSMD400.W60 VOLTAGE CODE VRRM, MAXIMUM REPETITIVE PEAK REVERSE VOLTAGE V VRSM, MAXIMUM NON-REPETITIVE PEAK REVERSE VOLTAGE V IRRM MAXIMUM AT TJ = 175 °C mA 60 600 700 12 Revision: 05-Jan-18 Document Number: 93469 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-VSMD400AW60, VS-VSMD400CW60 www.vishay.com Vishay Semiconductors FORWARD CONDUCTION PARAMETER SYMBOL Maximum average forward current at case temperature per leg IF(AV) Maximum RMS forward current per leg IF(RMS) TEST CONDITIONS VALUES UNITS 180° conduction, half sine wave, 133 °C 200 A DC at 137 °C case temperature 314 t = 10 ms Maximum peak, one-cycle forward, non-repetitive surge current per leg IFSM t = 8.3 ms t = 10 ms t = 8.3 ms t = 10 ms Maximum I2t for fusing per leg I2t Maximum I2t for fusing per leg I2t t = 8.3 ms 2500 No voltage reapplied 2620 100 % VRRM  reapplied No voltage reapplied Sinusoidal half wave,  initial TJ = TJ maximum 2200 32 29 100 % VRRM  reapplied 22 t = 0.1 ms to 10 ms, no voltage reapplied 311 t = 10 ms t = 8.3 ms A 2100 kA2s 20 Low level value of threshold voltage per leg VF(TO)1 (16.7 % x  x IF(AV) < I <  x IF(AV)), TJ = TJ maximum 0.73 High level value of threshold voltage per leg VF(TO)2 (I >  x IF(AV)), TJ = TJ maximum 0.85 kA2s V Low level value of forward slope resistance per leg rf1 (16.7 % x  x IF(AV) < I <  x IF(AV)), TJ = TJ maximum 1.52 High level value of forward slope resistance per leg rf2 (I >  x IF(AV)), TJ = TJ maximum 1.36 IFM = 200 A, TJ = 25 °C, tp = 400 μs square wave 1.31 V m Maximum forward voltage drop per leg VFM BLOCKING PARAMETER SYMBOL Maximum peak reverse leakage current per leg IRRM VALUES UNITS TJ = 175 °C TEST CONDITIONS 12 mA TJ = 25 °C 200 μA THERMAL AND MECHANICAL SPECIFICATIONS PARAMETER SYMBOL VALUES UNITS MIN. TYP. MAX. - - 0.10 - - 0.05 - 0.10 - - 68 - g - 2.4 - oz. Mounting torque 30 (3.4) - 40 (4.6) Mounting torque center hole 12 (1.4) - 18 (2.1) Terminal torque per leg Thermal resistance, junction to case per module Thermal resistance, case to heatsink per module RthJC RthCS Weight °C/W 30 (3.4) - 40 (4.6) Vertical pull - - 80 2” lever pull - - 35 Case style lbf · in (N · m) lbf · in TO-244 R CONDUCTION PER JUNCTION DEVICES VSMD400.W60 SINE HALF WAVE CONDUCTION RECTANGULAR WAVE CONDUCTION 180° 120° 90° 60° 30° 180° 120° 90° 60° 30° 0.041 0.047 0.060 0.084 0.131 0.029 0.049 0.064 0.087 0.132 UNITS °C/W Note • Table shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC Revision: 05-Jan-18 Document Number: 93469 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-VSMD400AW60, VS-VSMD400CW60 www.vishay.com Vishay Semiconductors 180 2500 2300 Ø 160 Conduction angle 150 140 130 120 30° 60° 90° 180° 110 Peak Half Sine Wave Forward Current (A) Maximum Allowable Case Temperature (°C) 170 120° 100 60 Hz 0.0083 s 50 Hz 0.0100 s 1700 1500 1300 1100 900 500 0 40 80 120 160 200 1 220 10 100 Number of Equal Amplitude Half Cycle Current Pulses (N) Fig. 3 - Maximum Non-Repetitive Surge Current Per Leg Average Forward Current Per Leg (A) Fig. 1 - Current Ratings Characteristics Per Leg 180 2500 2300 170 Ø 160 Peak Half Sine Wave Forward Current (A) Maximum Allowable Case Temperature (°C) 1900 700 90 Conduction angle 150 140 DC 130 120 90° 30° 110 180° 120° 60° 100 2100 1900 1700 No voltage reapplied 1500 1300 1100 900 Rated VRRM reapplied 700 500 0.01 90 0 50 100 150 200 250 300 350 0.1 1 Pulse Train Duration (s) Average Forward Current Per Leg (A) Fig. 2 - Current Ratings Characteristics Per Leg Fig. 4 - Maximum Non-Repetitive Surge Current Per Leg 350 50 75 .1 /W °C 0 =0 50 1.5 A Ø Conduction angle 200 R thS 100 /W 1° W 150 °C / °C RMS limit 7 /W 200 0. 250 3 250 300 °C 180° 120° 90° 60° 30° 0. 300 Maximum Average On-State Power Loss (W) 350 5 0. Maximum Average On-State Power Loss (W) 2100 C/ W °C/ W 150 3 °C /W 100 50 0 0 40 80 120 160 200 0 25 100 125 150 175 200 Average Forward Current Per Leg (A) Maximum Allowable Ambient Temperature (°C) Fig. 5 - Forward Power Loss Characteristics Revision: 05-Jan-18 Document Number: 93469 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-VSMD400AW60, VS-VSMD400CW60 www.vishay.com Vishay Semiconductors 450 200 DC 150 100 Ø 50 Conduction angle 0 0.5 250 °C /W °C /W /W W RMS limit 300 °C / °C 250 2 0.3 1 0. 300 0. 350 = 350 400 SA 180° 120° 90° 60° 30° Maximum Average On-State Power Loss (W) 400 R th Maximum On-State Forward Power Loss (W) 450 0.7 °C/ W 1 °C /W 200 150 3 °C/W 100 50 0 0 40 80 120 160 200 240 280 320 0 20 40 60 80 100 120 140 160 Average Forward Current Per Leg (A) Instantaneous Forward Current (A) Maximum Allowable Ambient Temperature (°C) Fig. 6 - Forward Power Loss Characteristics 1000 TJ = 175 °C 100 TJ = 25 °C 10 1 0 0.5 1.0 1.5 2.0 2.5 3.0 Instantaneous Forward Voltage (V) Fig. 7 - Forward Voltage Drop Characteristics Per Leg ZthJC - Transient Thermal Impedance (°C/W) 1 Steady state value RthJC = 0.10 °C/W 0.1 0.01 VSMD400..W60 0.001 0.001 0.01 0.1 1 10 Square Wave Pulse Duration (s) Fig. 8 - Thermal Impedance ZthJC Characteristics Per Leg Revision: 05-Jan-18 Document Number: 93469 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-VSMD400AW60, VS-VSMD400CW60 www.vishay.com Vishay Semiconductors ORDERING INFORMATION TABLE Device code VS-VS MD 1 2 400 C W 60 3 4 5 6 1 - Vishay Semiconductors product 2 - MD = standard recovery diode 3 - Current rating (400 = 400 A) 4 - Circuit configuration: C = two diodes common cathode A = two diodes common anode 5 - Type of device: W = TO-244 not isolated 6 - Voltage rating (60 = 600 V) CIRCUIT CONFIGURATION CIRCUIT DESCRIPTION CIRCUIT CONFIGURATION CODE CIRCUIT DRAWING Lug terminal cathode 1 Two diodes common anode Lug terminal cathode 2 A Base common anode Lug terminal anode 1 Two diodes common cathode Lug terminal anode 2 C Base common cathode LINKS TO RELATED DOCUMENTS Dimensions www.vishay.com/doc?95021 Revision: 05-Jan-18 Document Number: 93469 5 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2023 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2023 1 Document Number: 91000