2SK3388

2SK3388 TOSHIBA Field Effect Transistor Silicon N Channel MOS Type (π-MOSV) 2SK3388 Switching Regulator and DC-DC Converter Applications Motor Drive Applications • • • • Low drain-source ON resistance: RDS (ON) = 82 mΩ (typ.) High forward transfer admittance: |Yfs| = 20 S (typ.) Low leakage current: IDSS = 100 μA (VDS = 250 V) Enhancement mode: Vth = 1.5 to 3.5 V (VDS = 10 V, ID = 1 mA) Unit: mm Absolute Maximum Ratings (Ta = 25°C) Characteristics Drain-source voltage Drain-gate voltage (RGS = 20 kΩ) Gate-source voltage Drain current DC (Note 1) Symbol VDSS VDGR VGSS ID IDP PD EAS IAR EAR Tch Tstg Rating 250 250 ±20 20 60 125 487 20 12.5 150 −55~150 Unit V V V A W mJ A mJ °C °C Pulse (Note 1) Drain power dissipation (Tc = 25°C) Single pulse avalanche energy (Note 2) Avalanche current Repetitive avalanche energy (Note 3) Channel temperature Storage temperature range JEDEC JEITA TOSHIBA ― SC-97 2-9F1B Weight: 0.74 g (typ.) Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Thermal Characteristics Characteristics Thermal resistance, channel to case Symbol Rth (ch-c) Max 1.00 Unit °C/W Circuit Configuration Notice: Please use the S1 pin for gate input signal return. Make sure that the main current flows into the S2 pin. 4 Note 1: Ensure that the channel temperature does not exceed 150°C. Note 2: VDD = 50 V, Tch = 25°C (initial), L = 2.06 mH, IAR = 20 A, RG = 25 Ω Note 3: Repetitive rating: pulse width limited by maximum channel temperature This transistor is an electrostatic-sensitive device. Please handle with caution. 1 2 3 1 2006-11-21 2SK3388 Marking Part No. (or abbreviation code) K3388 Lot No. A line indicates lead (Pb)-free package or lead (Pb)-free finish. Electrical Characteristics (Note 4) (Ta = 25°C) Characteristics Gate leakage current Drain cut-off current Drain-source breakdown voltage Gate threshold voltage Drain-source ON resistance Forward transfer admittance Input capacitance Reverse transfer capacitance Output capacitance Rise time Turn-on time Switching time Fall time Turn-off time Total gate charge (gate-source plus gate-drain) Gate-source charge Gate-drain (“miller”) charge tf toff Qg Qgs Qgd Symbol IGSS IDSS V (BR) DSS Vth RDS (ON) |Yfs| Ciss Crss Coss tr ton VGS 10 V 0V 4.7 Ω ID = 1 0 A RL = 12.5Ω VDS = 10 V, VGS = 0 V, f = 1 MHz Test Condition VGS = ±16 V, VDS = 0 V VDS = 250 V, VGS = 0 V ID = 10 mA, VGS = 0 V VDS = 10 V, ID = 1 mA VGS = 10 V, ID = 10 A VDS = 10 V, ID = 10 A Min ⎯ ⎯ 250 1.5 ⎯ 10 ⎯ ⎯ ⎯ ⎯ VOUT ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Typ. ⎯ ⎯ ⎯ ⎯ 82 20 4000 300 1000 7 20 25 145 100 70 30 Max ±10 100 ⎯ 3.5 105 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ns ⎯ ⎯ ⎯ ⎯ ⎯ nC pF Unit μA μA V V mΩ S VDD ∼ 125 V − Duty < 1%, tw = 10 μs = VDD ∼ 200 V, VGS = 10 V, − ID = 2 0 A Note 4: Connect the S1 and S2 pins together, and ground them except during switching time measurement. Source-Drain Ratings and Characteristics (Note 5) (Ta = 25°C) Characteristics Continuous drain reverse current (Note 1, Note 5) Pulse drain reverse current (Note 1, Note 5) Continuous drain reverse current (Note 1, Note 5) Pulse drain reverse current (Note 1, Note 5) Forward voltage (diode) Reverse recovery time Reverse recovery charge Symbol IDR1 IDRP1 IDR2 IDRP2 VDS2F trr Qrr Test Condition ⎯ ⎯ ⎯ ⎯ IDR1 = 20 A, VGS = 0 V IDR = 20 A, VGS = 0 V, dIDR/dt = 100 A/μs Min ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Typ. ⎯ ⎯ ⎯ ⎯ ⎯ 300 3.3 Max 20 60 1 4 −2.0 ⎯ ⎯ Unit A A A A V ns μC Note 5: IDR1, IDRP1:Current flowing between the drain and the S2 pin. Ensure that the S1 pin is left open. IDR2, IDRP2:Current flowing between the drain and the S1 pin. Ensure that the S2 pin is left open. Unless otherwise specified, connect the S1 and S2 pins together, and ground them. 2 2006-11-21 2SK3388 ID – VDS 20 10 4.5 16 100 6 4.2 Common source Tc = 25°C Pulse test 4 8 3.8 80 Common source Tc = 25°C Pulse test ID – VDS 8 10 6 5.5 Drain current ID (A) 12 Drain current ID (A) 60 5 40 4.5 20 VGS = 4 V 0 0 4 VGS = 3.5 V 0 0 1 2 3 4 5 4 8 12 16 20 Drain-source voltage VDS (V) Drain-source voltage VDS (V) ID – VGS 50 Common source 4 VDS – VGS Common source Tc = 25°C Pulse test 3 40 Pulse test Drain current ID (A) Drain-source voltage 30 VDS (V) VDS = 10 V 2 ID = 2 0 A 20 100 10 Tc = −55°C 1 25 10 5 0 0 2 4 6 8 10 0 0 5 10 15 20 Gate-source voltage VGS (V) Gate-source voltage VGS (V) ⎪Yfs⎪ – ID 100 Common source 1000 Common source Tc = −55°C 100 25 Tc = 25°C Pulse test VDS = 10 V Pulse test RDS (ON) – ID Forward transfer admittance ⎪Yfs⎪ (S) 10 Drain-source on resistance RDS (ON) (mΩ) 100 VGS = 10, 15 V 1 1 10 100 10 1 10 100 Drain current ID (A) Drain current ID (A) 3 2006-11-21 2SK3388 RDS (ON) – Tc (mΩ) 200 Common source 160 VGS = 10 V Pulse test ID = 2 0 A 120 5 10 100 Common source Tc = 25°C Pulse test 10 IDR – VDS Drain-source on resistance RDS (ON) Drain reverse current IDR (A) VGS = 10 V 5 3 1 80 1 0 40 0 −80 −40 0 40 80 120 160 0.1 0 −0.2 −0.4 −0.6 −0.8 −1 −1.2 −1.4 −1.6 Case temperature Tc (°C) Drain-source voltage VDS (V) Capacitance – VDS 10000 Ciss 4 Vth – Tc Common source Vth (V) VDS = 10 V 3 ID = 1 m A Pulse test (pF) Gate threshold voltage 1000 Coss Capacitance C 2 100 Common source VGS = 0 V f = 1 MHz Tc = 25°C 10 0.1 1 10 Crss 1 0 −80 100 −40 0 40 80 120 160 Case temperature Tc (°C) Drain-source voltage VDS (V) PD – Tc 200 500 Dynamic input/output characteristics 20 Common source ID = 2 0 A 400 Tc = 25°C Pulse test VDD = 50 V 300 VGS 200 VDS 100 200 8 12 Drain power dissipation PD (W) VDS (V) 160 16 Drain-source voltage 80 40 100 4 10 0 40 80 120 160 200 0 0 40 80 120 160 0 200 Case temperature Tc (°C) Total gate charge Qg (nC) 4 2006-11-21 Gate-source voltage 120 VGS (V) 2SK3388 rth – tw 10 Normalized transient thermal impedance rth (t)/Rth (ch-c) 1 Duty = 0.5 0.2 0.1 0.1 0.05 0.02 0.01 0.01 0.00001 PDM t T Duty = t/T Rth (ch-c) = 1.0°C/W 0.001 0.01 0.1 1 10 Single pulse 0.0001 Pulse width tw (s) Safe operating area 100 ID max (pulsed) * 100 μs* 1 m s* ID max 10 (continuous) DC operation Tc = 25°C 500 EAS – Tch Avalanche energy EAS (mJ) 400 (A) Drain current ID 300 200 1 * Single nonrepetitive pulse Tc = 25°C Curves must be derated linearly with increase in temperature. 100 0.1 1 VDSS max 100 1000 0 25 50 75 100 125 150 10 Channel temperature (initial) Tch (°C) Drain-source voltage VDS (V) 15 V −15 V BVDSS IAR VDD VDS Waveform Ε AS = ⎛ ⎞ 1 B VDSS ⎟ ⋅ L ⋅ I2 ⋅ ⎜ ⎜B 2 − VDD ⎟ ⎝ VDSS ⎠ Test circuit RG = 25 Ω VDD = 50 V, L = 2.06 mH 5 2006-11-21 2SK3388 RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 6 2006-11-21