SSM6J409TU(TE85L,F

SSM6J409TU TOSHIBA Field-Effect Transistor Silicon P-Channel MOS Type (U-MOS V) SSM6J409TU ○ Power Management Switch Applications ○ High-Speed Switching Applications Unit: mm • 1.5V drive • Low ON-resistance: Ron = 72.3mΩ (max) (@VGS = -1.5 V) Ron = 46.2mΩ (max) (@VGS = -1.8 V) Ron = 30.2mΩ (max) (@VGS = -2.5 V) Ron = 22.1mΩ (max) (@VGS = -4.5 V) Absolute Maximum Ratings (Ta = 25°C) Characteristic Symbol Rating Unit Drain-Source voltage VDSS −20 V Gate-Source voltage VGSS ±8 V Drain current DC ID (Note 1) −9.5 Pulse IDP (Note 1) −19.0 PD (Note 2) 1 t=10s 2 Drain power dissipation A 1,2,5,6 : Drain 3 : Gate 4 : Source W Channel temperature Tch 150 °C Storage temperature range Tstg −55 to 150 °C Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability estimated failure rate, etc). JEDEC ⎯ JEITA ⎯ TOSHIBA 2-2T1D Weight: 7.6mg (typ.) data (i.e. reliability test report and Note 1: The junction temperature should not exceed 150°C during use. 2 Note 2: Mounted on an FR4 board. (25.4 mm × 25.4 mm × 1.6 mm, Cu Pad: 645 mm ) Marking 6 Equivalent Circuit (top view) 5 4 6 5 4 3 1 2 3 K 11 1 2 Handling Precaution When handling individual devices that are not yet mounted on a circuit board, make sure that the environment is protected against electrostatic discharge. Operators should wear antistatic clothing, and containers and other objects that come into direct contact with devices should be made of antistatic materials. Start of commercial production 2009-06 1 2014-03-01 SSM6J409TU Electrical Characteristics (Ta = 25°C) Characteristic Symbol Drain-Source breakdown voltage Test Conditions Min Typ. Max V (BR) DSS ID = -1 mA, VGS = 0 V -20 ⎯ ⎯ V (BR) DSX ID = -1 mA, VGS = +8 V -12 ⎯ ⎯ Unit V Drain cut-off current IDSS VDS = -20 V, VGS = 0 V ⎯ ⎯ -10 μA Gate leakage current IGSS VGS = ±8 V, VDS = 0 V ⎯ ⎯ ±1 μA Vth VDS = -3 V, ID = -1 mA -0.3 ⎯ -1.0 V ⏐Yfs⏐ VDS = -3 V, ID = -3.0 A (Note 3) 10 20 ⎯ S ID = -3.0 A, VGS = -4.5 V (Note 3) ⎯ 17.8 22.1 ID = -2.0 A, VGS = -2.5 V (Note 3) ⎯ 23.5 30.2 ID = -1.5 A, VGS = -1.8 V (Note 3) ⎯ 31.5 46.2 ID = -0.8 A, VGS = -1.5 V (Note 3) ⎯ 40.0 72.3 ⎯ 1100 ⎯ ⎯ 240 ⎯ ⎯ 180 ⎯ ⎯ 15.0 ⎯ ⎯ 10.9 ⎯ ⎯ 4.1 ⎯ Gate threshold voltage Forward transfer admittance Drain–source ON-resistance RDS (ON) Input capacitance Ciss Output capacitance Coss Reverse transfer capacitance Crss Total Gate Charge Qg Gate-Source Charge Qgs Gate-Drain Charge Qgd Switching time VDS = -10 V, VGS = 0 V, f = 1 MHz VDD = −10 V, ID = −9.5 A VGS = −4.5 V pF nC Turn-on time ton VDD = -10 V, ID = -2.0 A, ⎯ 40 ⎯ Turn-off time toff VGS = 0 to -2.5 V, RG = 4.7 Ω ⎯ 207 ⎯ ⎯ 0.83 1.2 Drain-Source forward voltage VDSF ID = 9.5 A, VGS = 0 V (Note 3) mΩ ns V Note3: Pulse test Switching Time Test Circuit (a) Test Circuit (b) VIN ID 0 0V OUT IN −2.5 V 90% −2.5 V RG 10 μs 10% VDD (c) VOUT VDD = − 10 V RG = 4.7 Ω D.U. ≤ 1% VIN: tr, tf < 5 ns Common Source Ta = 25°C VDS (ON) VDD 90% 10% tr ton tf toff Notice on Usage Vth can be expressed as the voltage between gate and source when the low operating current value is ID = -1 mA for this product. For normal switching operation, VGS (on) requires a higher voltage than Vth and VGS (off) requires a lower voltage than Vth. (The relationship can be established as follows: VGS (off) < Vth < VGS (on).) Take this into consideration when using the device. 2 2014-03-01 SSM6J409TU ID – VDS VGS = -4.5 V ID – VGS -100 -2.5 V Common Source VDS = -3 V -1.8 V -10 (A) -16 -1 ID -1.5 V -12 Drain current Drain current ID (A) -20 -8 -4 -0.1 Ta = 100 °C −25 °C -0.01 25 °C -0.001 0 Common Source Ta = 25 °C 0 -0.2 -0.6 -0.4 Drain–source voltage -0.8 VDS -0.0001 0 -1 -0.5 (V) Gate–source voltage RDS (ON) – VGS Common Source 80 60 40 25 °C Ta = 100 °C 20 0 −25 °C 0 -2 -4 Gate–source voltage -6 VGS Common Source 80 60 40 25 °C Ta = 100 °C 20 −25 °C 0 -2 (V) Drain–source ON-resistance RDS (ON) (mΩ) Drain–source ON-resistance RDS (ON) (mΩ) Ta = 25 °C 60 VGS = -1.5 V -1.8 V -2.5 V -4.5 V 0 -5 -10 Drain current -15 ID -6 VGS -8 (V) RDS (ON) – Ta 60 Common Source 0 -4 Gate–source voltage RDS (ON) – ID 20 (V) ID = -3.0A 100 0 -8 80 40 VGS -2.0 RDS (ON) – VGS ID = -0.8 A 100 -1.5 120 Drain–source ON-resistance RDS (ON) (mΩ) Drain–source ON-resistance RDS (ON) (mΩ) 120 -1.0 Common Source 50 40 (A) -1.5 A / -1.8 V -2.0 A / -2.5 V 30 20 -3.0 A / -4.5 V 10 0 −50 -20 ID = -0.8 A / VGS = -1.5 V 0 50 100 Ambient temperature Ta 3 150 (°C) 2014-03-01 SSM6J409TU Vth – Ta ID = -1 mA -0.8 (S) VDS = -3 V 50 10 Forward transfer admittance Gate threshold voltage Vth (V) Common Source ⎪Yfs⎪ |Yfs| – ID -1.0 -0.6 -0.4 -0.2 0 −50 50 0 100 Ambient temperature Ta 150 Common Source VDS = -3 V Ta = 25 °C 3 1 0.3 0.1 0.03 0.01 -0.001 -0.01 Drain current (°C) C – VDS 5000 -1 -0.1 -10 ID -100 (A) Dynamic Input Characteristic -8 VGS 1000 Ciss 500 Gate–source voltage Capacitance C (pF) (V) 3000 300 Coss 100 Crss 50 Common Source 30 Ta = 25 °C f = 1 MHz VGS = 0 V 10 -0.1 -1 -10 Drain–source voltage VDD = -10 V VDD = -16 V -4 -2 Common Source ID = -9.5 A Ta = 25 °C 0 -100 VDS -6 0 10 Total Gate Charge (V) t – ID 1000 (A) Drain reverse current Switching time ton 1 -0.01 tr Common Source -0.1 Drain current (nC) Common Source VDD = -10 V VGS = 0 to -2.5 V Ta = 25 °C RG = 4.7 Ω -1 -10 ID D IDR Ta = 25 °C 10 IDR 100 t (ns) tf - Qg 30 IDR – VDS 100 toff VGS = 0 V 10 20 G S 1 0. 1 25 °C 0.01 100 °C 0.001 0 0.2 −25 °C 0.4 0.6 Drain–source voltage (A) 4 0.8 VDS 1.0 1.2 (V) 2014-03-01 SSM6J409TU – tw PD – Ta 600 Drain power dissipation PD (W) Transient thermal impedance Rth (°C/W) rth 100 10 Single pulse Mounted on FR4 Board (25.4mm × 25.4mm × 1.6mm , 2 Cu Pad : 645 mm ) 1 0.001 0.01 0.1 1 Pulse width 10 tw 100 2.5 2 (s) 10s 1.5 DC 1 0.5 0 -40 1000 Mounted on FR4 Board (25.4mm × 25.4mm × 1.6mm , 2 Cu Pad : 645 mm ) -20 0 20 40 60 80 Ambient temperature 5 100 120 140 Ta (°C) 160 2014-03-01 SSM6J409TU RESTRICTIONS ON PRODUCT USE • Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. • This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. • Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. • PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT ("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales representative. • Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. • Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. • ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. • Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. • Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS. 6 2014-03-01