HV06W4J0165T5E

High Voltage Thick Film Chip Resistors DATA SHEET Product Name High Voltage Thick Film Chip Resistors Part Name HV Series Uniroyal Electronics Global Co., Ltd. 88#, Longteng Road, Economic & Technical Development Zone, Kunshan, Jiangsu, China Tel Email Manufacture Plant +86 512 5763 1411 / 22 /33 marketing@uni-royal.cn Uniroyal Electronics Industry Co., Ltd. Aeon Technology Corporation Royal Electronic Factory (Thailand) Co., Ltd. Royal Technology (Thailand) Co., Ltd. Feb. 12, 2019 V2 www. uni-royal.cn P1/5 High Voltage Thick Film Chip Resistors 1 Scope 1.1 1.2 1.3 1.4 This datasheet is the characteristics of High Voltage Thick Film Chip Resistors manufactured by UNI-ROYAL. The performance in Max. Working Voltage is superior to the general thick film chip resistors. Suitable for reflow & wave soldering Applications: AV adapters, LCD backlight, Camera flash, etc. 2 Part No. System Part No. includes 14 codes shown as below: 2.1 1st~4th codes: Part name. E.g.: HV03, HV05, HV06, HV07, HV10, HV12 2.2 5th~6th codes: Power rating. E.g.: W=Normal Size “1~G” = “1~16” Wattage 1/32 3/4 1/2 1/3 1/4 1/8 1/10 1/16 1/20 1 Normal Size WH 07 W2 W3 W4 W8 WA WG WM 1W If power rating is equal or lower than 1 watt, 5th code would be “W” and 6th code would be a number or letter. E.g.: WA=1/10W W4=1/4W 2.3 7th code: Tolerance. E.g.: D=±0.5% F=±1% G=±2% J=±5% K= ±10% 2.4 8th~11th codes: Resistance value. 2.4.1 If value belongs to standard value of E-24 series, the 8th code is zero, 9th~10th codes are the significant figures of resistance value, and the 11th code is the power of ten. 2.4.2 If value belongs to standard value of E-96 series, the 8th~10th codes are the significant figures of resistance value, and the 11th code is the power of ten. 2.4.3 11th codes listed as following: 0=100 1=101 2=102 3=103 4=104 5=105 6=106 J=10-1 K=10-2 L=10-3 M=10-4 th th 2.5 12 ~14 codes. 2.5.1 12th code: Packaging Type. E.g.: B = Bulk / Box T=Tape/Reel 2.5.2 13th code: Standard Packing Quantity. 4=4,000pcs 5=5,000pcs C=10,000pcs D=20,000pcs E=15,000pcs Chip Product: BD=B/B-20000pcs TC=T/R-10000pcs 2.5.3 14th code: Special features. E = Environmental Protection, Lead Free, or Standard type. 3 Ordering Procedure (Example: HV06 1/4W ±1% 100KΩ T/R-5000) H V 0 6 Product Type: Fill-in 4 digits with the chip resistor type as follows: HV03 HV05 HV06 HV07 HV10 HV12 W 4 F 1 Wattage: WA=1/10W W8=1/8W W4=1/4W W2=1/2W 1W=1W 07=3/4W 0 0 3 T Resistance Value: 5% (E-24 series): 1st code is zero, 2nd~3rd codes are the significant figures of resistance value, and the rest code is the power of ten. 1% (E-96 series): 1st~3rd codes are the significant figures of resistance value and the rest code is the power of ten. 5 E Packing quantity: 1=1 Kpcs. 2=2 Kpcs. 3=3 Kpcs. 4=4 Kpcs. 5=5 Kpcs. C=10 Kpcs. D=20 Kpcs. J=10-1; K=10-2; L=10-3 Tolerance: F=±1% J=±5% Feb. 12, 2019 V2 www. uni-royal.cn Packing Type: T=Tape/Reel Special Feature: E= Lead-Free P2/5 High Voltage Thick Film Chip Resistors 4 Marking 4.1 ±5% tolerance products (E-24 series): 3 codes. 1st~2nd codes are the significant figures of resistance value, and the rest code is the power of ten. 104 → 100KΩ 4.2 ±1% tolerance products (E-96 series): 4 codes. 1st~3rd codes are the significant figures of resistance value, and the rest code is the power of ten. Letter "R" in mark means decimal point. 1003 → 100KΩ 5 Dimension Dimension(mm) Type L HV03(0603) HV05(0805) 1.60±0.10 2.00±0.15 W 0.80±0.10 H A B 0.45±0.10 0.30±0.20 0.30±0.20 +0.15 -0.10 0.55±0.10 0.40±0.20 0.40±0.20 +0.15 -0.10 1.25 HV06(1206) 3.10±0.15 1.55 0.55±0.10 0.45±0.20 0.45±0.20 HV07(1210) 3.10±0.10 2.60±0.20 0.55±0.10 0.50±0.25 0.50±0.20 HV10(2010) 5.00±0.10 2.50±0.20 0.55±0.10 0.60±0.25 0.50±0.20 HV12(2512) 6.35±0.10 3.20±0.20 0.55±0.10 0.60±0.25 0.50±0.20 6 7 Ratings Type Power Rating at 70℃ Max. Working Voltage Max. Overload Voltage Dielectric withstanding Voltage Resistance Range Operating Temperature HV03 1/10W 200V 400V 300V 36KΩ~10MΩ -55℃~155℃ HV05 1/8W 400V 800V 500V 100KΩ~10MΩ -55℃~155℃ HV06 1/4W 500V 1000V 500V 100KΩ~10MΩ -55℃~155℃ HV07 1/2W 800V 1500V 500V 50KΩ~10MΩ -55℃~155℃ HV10 3/4W 2000V 3000V 500V 50KΩ~10MΩ -55℃~155℃ HV12 1W 3000V 4000V 500V 39KΩ~10MΩ -55℃~155℃ Soldering pad size recommended Type HV03 HV05 HV06 HV07 HV10 HV12 A 0.8±0.05 1.0±0.1 2.2±0.1 2.1±0.1 3.6±0.1 5.0±0.1 Dimension(mm) B C 0.65±0.05 0.8±0.05 1.0±0.1 1.3±0.1 1.1±0.1 1.6±0.1 1.1±0.1 2.6±0.1 1.3±0.1 2.6±0.1 1.6±0.1 3.3±0.1 D 2.1±0.05 3.0±0.1 4.4±0.1 4.4±0.1 6.2±0.1 8.2±0.1 8 Derating Curve Power rating will change based on continuous load at ambient temperature from -55 to 155℃. It is constant between -55 to 70℃, and derate to zero when temperature rise from 70 to 155℃. Voltage rating: Resistors shall have a rated direct-current (DC) continuous working voltage or an approximate sine-wave root-mean-square (RMS) alternating-current (AC) continuous working voltage at commercial-line frequency and waveform corresponding to the power rating, as determined from the following formula: RCWV = √𝑃 × R Remark: RCWV: Rating Continuous Working Voltage (Volt.) P: power rating (Watt) R: nominal resistance (Ω) In no case, the rated DC or RMS AC continuous working voltage must be greater than the applicable maximum value. The overload voltage is 2.5 times RCWV or Max. Overload voltage whichever is lower. Feb. 12, 2019 V2 www. uni-royal.cn P3/5 High Voltage Thick Film Chip Resistors 9 Structure 10 Performance Specification Characteristic Test Methods (GB/T5729&JIS-C-5201&IEC60115-1) Limits 4.8 Natural resistance changes per temp. Degree centigrade Temperature Coefficient Short-time overload Terminal bending Dielectric withstanding voltage Soldering heat Insulation resistance Solderability Rapid change of temperature R2−R1 ±(2.0%+0.1Ω) ±(1.0%+0.05Ω) No evidence of flashover mechanical damage, arcing or insulation breaks down. ±(1.0%+0.05Ω) ≧1000MΩ ±5%：±(1.0%+0.05Ω) ±1%：±(0.5%+0.05Ω) Load life in humidity ±(3.0%+0.1Ω) Load life ±(3.0%+0.1Ω) Feb. 12, 2019 V2 4.7 Resistors shall be clamped in the trough of a 90℃metallic vblock and shall be tested at ac potential respectively specified in the given list of each product type for 60-70 seconds. 4.18 Dip the resistor into a solder bath having a temperature of 260℃±5℃ and hold it for 10±1 seconds. 4.6 The measuring voltage shall be ,measured with a direct voltage of (100±15)V or a voltage equal to the dielectric withstanding voltage., and apply for 1min. Wave solder: Test temperature of solder: 245℃±3℃ dipping time in solder: 2-3 seconds. Reflow: Coverage must be over 95%. ±(3.0%+0.1Ω) Leaching ×106 (PPM/℃) R 1 : Resistance Value at room temperature t 1 R 2 : Resistance at test temperature (Upper limit temperature or Lower limit temperature) t 1: Room temperature +25°C or specified t 2: Upper limit or Lower limit temperature 4.13 Permanent resistance change after the application of 2.5 times RCWV for 5 seconds. 4.33 Twist of test board: Y/X = 3/90 mm for 60 Seconds ±100PPM/℃ Humidity ( steady state ) Low Temperature Storage High Temperature Exposure 𝑅1(𝑡2−𝑡1) 4.19 30 min at lower limit temperature and 30 min at upper limit temperature 100 cycles. 4.24Temporary resistance change after 240 hours exposure in a humidity test chamber controlled at 40±2℃ and 90-95% relative humidity 7.9 Resistance change after 1,000 hours (1.5 hours “ON”,0.5 hour “OFF”) at RCWV in a humidity chamber controlled at 40 ℃±2℃ and 90 to 95% relative humidity. 4.25.1 Permanent resistance change after 1,000 hours operating at RCWV with duty cycle 1.5 hours “ON”, 0.5 hour “OFF” at 70 ℃±2℃ ambient. ±(3.0%+0.1Ω) 4.23.4 Lower limit temperature，for 2H. ±(3.0%+0.1Ω) 4.23.2 Upper limit temperature ，for 16H. No visible damage J-STD-002 Test D Samples completely immersed for 30 sec in solder bath at 260℃ www. uni-royal.cn P4/5 High Voltage Thick Film Chip Resistors 11. Packing 11.1Dimension of Paper Taping: (Unit: mm) Type A ±0.2 B ±0.2 C ±0.05 HV03 HV05 HV06 HV07 1.10 1.65 2.00 2.80 1.90 2.40 3.60 3.50 2.00 2.00 2.00 2.00 ΦD +0.1 −0 1.50 1.50 1.50 1.50 E ±0.1 F ±0.05 G ±0.1 W ±0.2 T ±0.1 1.75 1.75 1.75 1.75 3.50 3.50 3.50 3.50 4.00 4.00 4.00 4.00 8.00 8.00 8.00 8.00 0.67 0.81 0.81 0.75 11.2 Dimension of plastic taping (Unit: mm) Type HV10 HV12 A ±0.2 B±0.2 C ±0.05 ΦD +0.1 E±0.1 F ±0.05 G ±0.1 W ±0.2 T ±0.1 ΦD1 +0.25 −0 −0 2.90 5.60 2.00 1.50 1.50 1.75 5.50 4.00 12.00 1.00 3.50 6.70 2.00 1.50 1.50 1.75 5.50 4.00 12.00 1.00 11.3 Dimension of Reel：(Unit: mm) Type Taping Qty/Reel A ±0.5 B ±0.5 C ±0.5 D ±1 M ±2 W ±1 HV03 Paper 5,000pcs 2.0 13.0 21.0 60.0 178.0 10.0 HV05 Paper 5,000pcs 2.0 13.0 21.0 60.0 178.0 10.0 HV06 Paper 5,000pcs 2.0 13.0 21.0 60.0 178.0 10.0 HV07 Paper 5,000pcs 2.0 13.0 21.0 60.0 178.0 10.0 HV10 Embossed 4,000pcs 2.0 13.0 21.0 60.0 178.0 13.8 HV12 Embossed 4,000pcs 2.0 13.0 21.0 60.0 178.0 13.8 12 Note 12.2 UNI-ROYAL recommend products store in warehouse with temperature between 15 to 35℃ under humidity between 25 to 75%RH. Even under storage conditions recommended above, solder ability of products will be degraded stored over 1 year old. 12.3 Cartons must be placed in correct direction which indicated on carton, otherwise the reel or wire will be deformed. 12.4 Storage conditions as below are inappropriate: a. Stored in high electrostatic environment b. Stored in direct sunshine, rain, snow or condensation. c. Exposed to sea wind or corrosive gases, such as Cl 2 , H 2 S, NH 3 , SO 2 , NO 2 , etc. 13 Record Version Description Page Date Amended by Checked by 1 First version 1~6 Mar.20, 2018 Haiyan Chen Nana Chen 2 Modify characteristic 4~5 Feb.12, 2019 Haiyan Chen Yuhua Xu © Uniroyal Electronics Global Co., Ltd. All rights reserved. Specification herein will be changed at any time without prior notice. Feb. 12, 2019 V2 www. uni-royal.cn P5/5