VXM7-9039-25M0000000

VXM7 3.2 x 2.5mm Crystal Standard Crystal Datasheet Helping Customers Innovate, Improve & Grow Table 1. Electrical Performance Parameter Nominal Frequency1 Symbol Min. FNOM 12.000 Mode Typ Max Units 60.000 MHz Fundamental, AT - Cut Operating Temperature Range, ordering option 2 OP Stability Over T , ordering option 2,3 TOP FSTAB Frequency Tolerance FTOL Load Capacitance, ordering option CL VT-804 Shunt Capacitance 0/70, -10/70, -20/70, -40/85 ±10 ±10 6 Co Drive Level Aging / 1st year (at 25 °C) Insulation Resistance Storage Temperature 10 FAGE Description500 TSTO °C ±100 ppm ±20 ppm 32 pF 5 pF 100 uW ±5 ppm MOhm -40 90 °C Equivalent Series Resistance Crystal Frequency ESR Ohm 12.000MHz-14.000MHz 100 14.001MHz-19.000MHz 80 Applications 19.001MHz-30.000MHz 60 30.001MHz-60.000MHz 40 Notes: Features 1. Higher frequency 3rd OT crystals can be supplied, such as 114M285 and 125M000. Please contact factory with requirements. 2. Referenced to the Frequency at 25 °C. 3. Frequency measured at 25 °C ± 3 °C. Product is compliant to RoHS directive and fully compatible with lead free assembly. Package Drawing XXXX XX XX YWW YWW Yww Yw wW Block Diagram Marking Option 1 XXMXXX YYWW C where XXMXX = Frequency YY = Year WW=Week C = Manufacturing Location Marking Option 2 VXXYM where V=Vectron XX = Frequency Y = Year M =Month A = January L = December Table 2. Pinout Botttom View All Dimensions in mm Page1 Pin Function 1 Crystal 2 Connected to cover (Connect to GND 3 Crystal 4 Connected to cover (Connect to GND) Table 3. Environmental Compliance Parameter Conditions Mechanical Shock MIL-STD-883, Method 2002, Condition B Mechanical Vibration MIL-STD-883, Method 2007, Condition A Temperature Cycle MIL-STD-883, Method 1010, Condition B Solderability MIL-STD-202-210, Condition B Gross and Fine Leak MIL-STD-883, Method 1014 Altitude MIL-STD-883, Method 1001, Condition B Moisture Sensitivity Level MSL 1 Contact Pads Gold (0.2 um min) over Nickel Weight 20 mg Reliability & IR Compliance Table 4: Reflow Profile Parameter Symbol Value PreHeat Time Ts-min Ts-max tS 60 sec Min, 260 sec Max 150°C 200°C Ramp Up RUP 3 °C/sec Max Time Above 217 °C tL 60 sec Min, 150 sec Max Time To Peak Temperature TAMB-P 480 sec Max Time at 260 °C tP 30 sec Max Ramp Down RDN 6 °C/sec Max Pads are Au over Ni and compatible with either SnPb or Pb free attachment. MSL: 1 Page2 Tape & Reel Table 5. Tape and Reel Dimensions (mm) Tape Reel A B C D E F G H J K L M A B C D E W T 3.6 2.9 8.0 3.5 1.75 4.0 4.0 2.0 0.5 1.55 0.25 1.0 180 60 21.0 13.0 2.0 9.0 2.0 3K pieces per reel Ordering Information VXM7 - XXX - XX- xxMxxxxxxxXX Product 3.2 x 2.5mm, Crystal Packaging TR: Tape and Reel blank: Cut Tape / non Tape and Reel quantities _SNPB: Tin lead solder dipped Mode 1: Fundamental Frequency in MHz Temp Stability C: ±10ppm D: ±15ppm E: ±20ppm F: ±25ppm G: ±30ppm H: ±35ppm I: ±40ppm J: ±45ppm *Note: not all combination of options are available. K: ±50ppm Other specifications may be available upon request. S: ±100ppm Example: VXM7-1EE-12-25M0000000TR VXM7-1EE-12-25M0000000 VXM7-1EE-12-25M0000000_SNPB Page3 Load Capacitance 0: Series Resonance 06-32pF Operating Temperature E: -40 to 85 °C H: -30 to 85 °C J: -20 to 70 °C W: -10 to 70 °C T: 0 to 70 °C Tape and Reel Cut Tape Tin lead solder dipped Revision History Revision Date Approved Description December 5, 2016 RC Updated ESR Table August 29, 2016 RC Initial datasheet for factory approval and release to customer. September 18, 2018 FB Update logo and contact information, add 1K reel pieces per reel and “SNPBDIP” ordering option June 7, 2019 FB Update logo and contact information, add Table 2 Environmental compliance, change “SNPBDIP” to “SNPB” April 30, 2020 FB Add tape and reel ordering option Previous Ordering Information for Reference Only Do Not Use to Build a New Part Number The ordering codes for the VXM7 were changed in 2016. If you had ordered a specific code based off this ordering method, it is still available for purchase under the old code however no new part numbers will be created using this system. Due to the change in the 8th character from numeric to alphabetic, there is no opportunity for overlap between the two ordering methods. Page4 Contact Information USA: 100 Watts Street Mt Holly Springs, PA 17065 Tel: 1.717.486.3411 Fax: 1.717.486.5920 Europe: For Additional Information, Please Contact Landstrasse 74924 Neckarbischofsheim Germany Tel: +49 (0) 7268.801.0 Fax: +49 (0) 7268.801.281 Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your reasonability to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATION OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION INCLUDING, BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly, or otherwise, under any Microchip intellectual property rights unless otherwise stated. Trademarks The Microchip and Vectron names and logos are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. Page5