VXM9-9014-64M0000000

VXM9 2.0 x 1.6mm Crystal Helping Customers Innovate, Improve & Grow Table 1. Electrical Performance Parameter Nominal Frequency Symbol Min. Typ FNOM 16.000 Mode Units 60.000 MHz Fundamental, AT - Cut Operating Temperature Range Stability Over TOP TOP 1 0/70, -10/70, -20/70, -40/85 FSTAB Frequency Tolerance2 FTOL Load Capacitance CL Shunt Capacitance Co Drive Level Max VT-804 ±10 ±10 6 10 Aging / 1st year (at 25 °C) FAGE °C ±100 ppm ±20 ppm 32 pF 5 pF 100 uW ±5 ppm 500 Description Insulation Resistance Storage Temperature TSTO -40 MOhm 90 °C Equivalent Series Resistance Crystal Frequency 16.000MHz-20.000MHz 20.001MHz-30.000MHz Features 30.001MHz-60.000MHz ESR Ohm 200 100 Applications 80 Notes: 1. Referenced to the Frequency at 25 °C. 2. Frequency measured at 25 °C ± 3 °C. Product is compliant to RoHS directive and fully compatible with lead free assembly. Package Drawing XX.X YMC Part Marking: XX.X = Frequency Y = Year M = Month A = January B = February C = March D = April E = May F = June G = July H = August I = September J = October K = November L = December C = Manufacuting Location Block Diagram Table 2. Pinout All Dimensions in mm Page1 Pin Function 1 Crystal 2 Connected to cover (Connect to GND 3 Crystal 4 Connected to cover (Connect to GND) Table 3. Environmental Compliance Parameter Conditions Mechanical Shock MIL-STD-883, Method 2002, Condition B Mechanical Vibration MIL-STD-883, Method 2007, Condition A Temperature Cycle MIL-STD-883, Method 1010, Condition B Solderability MIL-STD-202-210, Condition B Gross and Fine Leak MIL-STD-883, Method 1014 Altitude MIL-STD-883, Method 1001, Condition B Moisture Sensitivity Level MSL 1 Contact Pads Gold (0.2 um min) over Nickel Weight 7 mg Reliability & IR Compliance Table 4: Reflow Profile Parameter Symbol Value PreHeat Time Ts-min Ts-max tS 60 sec Min, 260 sec Max 150°C 200°C Ramp Up RUP 3 °C/sec Max Time Above 217 °C tL 60 sec Min, 150 sec Max Time To Peak Temperature TAMB-P 480 sec Max Time at 260 °C tP 30 sec Max Ramp Down RDN 6 °C/sec Max Pads are Au over Ni and compatible with either SnPb or Pb free attachment. MSL: 1 Page2 Tape & Reel Table 5. Tape and Reel Dimensions (mm) Tape Reel A B C D E F G H J K L M A B C D E W T 2.25 1.85 8.0 3.5 1.75 4.0 4.0 2.0 0.5 1.55 0.25 0.65 180 60 21.0 13.0 2.0 9.0 2.0 Ordering Information VXM9 - XXX - XX- xxMxxxxxxxXX Product 2.0 x 1.6mm, Crystal Packaging TR: Tape and Reel blank: Cut Tape / non Tape and Reel quantities _SNPB: Tin lead solder dipped Mode 1: Fundamental Frequency in MHz Temp Stability C: ±10ppm D: ±15ppm E: ±20ppm F: ±25ppm G: ±30ppm H: ±35ppm I: ±40ppm J: ±45ppm K: ±50ppm S: ±100ppm Load Capacitance 0: Series Resonance 06-32pF *Note: not all combination of options are available. Other specifications may be available upon request. Example: VXM9-1EE-12-25M0000000TR VXM9-1EE-12-25M0000000 VXM9-1EE-12-25M0000000_SNPB Operating Temperature E: -40 to 85 °C J: -20 to 70 °C W: -10 to 70 °C T: 0 to 70 °C Tape and Reel Cut Tape Tin lead solder dipped Page3 Revision History Revision Date Approved August 29, 2016 RC Initial datasheet for factory approval and release to customer. Description August 10, 2018 FB Update logo and contact information, add “SNPBDIP” ordering option June 07, 2019 FB Update logo and contact information, add Table 2 Environmental compliance, change “SNPBDIP” to “SNPB” For Additional Information, Please Contact FB Add tape and reel ordering option April 30, 2020 Previous Ordering Information for Reference Only Do Not Use to Build a New Part Number VXM9-1G2-10M000 Package VXM9 : 2.0x1.6x0.55 Frequency Mode 1 : Fundamental Load Capacitance 0: Series Resonator 1: 16 pf 2: 20 pf 3: 32 pf 4: 18 pf 5: 10 pF 6: 30 pf Stability A: ±100 ppm over -20o to 70oC B: ±50 ppm over -20o to 70oC C: ±100 ppm over -40o to 85oC D: ±50 ppm over -40o to 85oC F: ±30 ppm over -20o to 70oC A: ±10 ppm over -10o to 60oC A: ±15 ppm over -30o to 85oC The ordering codes for the VXM9 were changed in 2016. If you had ordered a specific code based off this ordering method, it is still available for purchase under the old code however no new part numbers will be created using this system. Due to the change in the 8th character from numeric to alphabetic, there is no opportunity for overlap between the two ordering methods. Contact Information USA: 100 Watts Street Mt Holly Springs, PA 17065 Tel: 1.717.486.3411 Fax: 1.717.486.5920 Europe: For Additional Information, Please Contact Landstrasse 74924 Neckarbischofsheim Germany Tel: +49 (0) 7268.801.0 Fax: +49 (0) 7268.801.281 Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your reasonability to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATION OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION INCLUDING, BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly, or otherwise, under any Microchip intellectual property rights unless otherwise stated. Trademarks The Microchip and Vectron names and logos are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. Page4