APT5015SVFR

APT5015BVFR APT5015SVFR 500V BVFR 32A 0.150Ω D3PAK POWER MOS V ® FREDFET TO-247 Power MOS V® is a new generation of high voltage N-Channel enhancement mode power MOSFETs. This new technology minimizes the JFET effect, increases packing density and reduces the on-resistance. Power MOS V® also achieves faster switching speeds through optimized gate layout. • Faster Switching • Lower Leakage • Avalanche Energy Rated • TO-247 or Surface Mount D3PAK Package SVFR D G S • Fast Recovery Body Diode MAXIMUM RATINGS Symbol VDSS ID IDM VGS VGSM PD TJ,TSTG TL IAR EAR EAS Parameter Drain-Source Voltage Continuous Drain Current @ TC = 25°C Pulsed Drain Current 1 All Ratings: TC = 25°C unless otherwise specified. APT5015BVFR_SVFR UNIT Volts Amps 500 32 128 ±30 ±40 370 2.96 -55 to 150 300 30 30 4 Gate-Source Voltage Continuous Gate-Source Voltage Transient Total Power Dissipation @ TC = 25°C Linear Derating Factor Operating and Storage Junction Temperature Range Lead Temperature: 0.063" from Case for 10 Sec. Avalanche Current 1 Volts Watts W/°C °C Amps mJ (Repetitive and Non-Repetitive) 1 Repetitive Avalanche Energy Single Pulse Avalanche Energy 1300 STATIC ELECTRICAL CHARACTERISTICS Symbol BVDSS ID(on) RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) On State Drain Current 2 MIN TYP MAX UNIT Volts Amps 500 32 0.15 250 1000 ±100 2 4 (VDS > ID(on) x R DS(on) Max, VGS = 10V) 2 Drain-Source On-State Resistance (VGS = 10V, 0.5 ID[Cont.]) Ohms µA 1-2005 050-5627 Rev A Zero Gate Voltage Drain Current (VDS = VDSS, VGS = 0V) Zero Gate Voltage Drain Current (VDS = 0.8 VDSS, VGS = 0V, TC = 125°C) Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Gate Threshold Voltage (VDS = VGS, ID = 1.0mA) APT Website - http://www.advancedpower.com nA Volts CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. DYNAMIC CHARACTERISTICS Symbol Ciss Coss Crss Qg Qgs Qgd t d(on) tr t d(off) tf Characteristic Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge 3 APT5015BVFR_SVFR Test Conditions VGS = 0V VDS = 25V f = 1 MHz VGS = 10V VDD = 0.5 VDSS ID = ID [Cont.] @ 25°C VGS = 15V VDD = 0.5 VDSS ID = ID [Cont.] @ 25°C RG = 1.6Ω MIN TYP MAX UNIT pF 4400 600 230 200 30 80 12 14 55 11 5280 840 350 300 45 120 25 30 80 20 ns nC Gate-Source Charge Gate-Drain ("Miller") Charge Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS Symbol IS ISM VSD dv/ dt Characteristic / Test Conditions Continuous Source Current (Body Diode) Pulsed Source Current Diode Forward Voltage Peak Diode Recovery 1 2 dt MIN TYP MAX UNIT Amps Volts V/ns ns µC Amps 32 128 1.3 15 Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C (Body Diode) (VGS = 0V, IS = -ID [Cont.]) 5 d v/ t rr Q rr IRRM Reverse Recovery Time (IS = -ID [Cont.], di/dt = 100A/µs) Reverse Recovery Charge (IS = -ID [Cont.], di/dt = 100A/µs) Peak Recovery Current (IS = -ID [Cont.], di/dt = 100A/µs) 250 525 1.6 6.0 13 21 THERMAL CHARACTERISTICS Symbol RθJC RθJA Characteristic Junction to Case Junction to Ambient MIN TYP MAX UNIT °C/W 0.34 40 1 Repetitive Rating: Pulse width limited by maximum junction temperature. 2 Pulse Test: Pulse width < 380 µS, Duty Cycle < 2% 3 See MIL-STD-750 Method 3471 4 Starting T = +25°C, L = 2.54mH, R = 25Ω, Peak I = 32A j G L 5 I - -I [Cont.], di/ = 100A/µs, V S D DD - VDSS, Tj - 150°C, RG = 2.0Ω, dt VR = 200V. APT Reserves the right to change, without notice, the specifications and information contained herein. 0.4 Z JC, THERMAL IMPEDANCE (°C/W) θ D=0.5 0.1 0.05 0.2 0.1 0.05 PDM 1-2005 0.01 0.005 0.02 0.01 SINGLE PULSE Note: t1 t2 Duty Factor D = t1/t2 Peak TJ = PDM x ZθJC + TC 050-5627 Rev A 0.001 10-5 10-3 10-2 10-1 1.0 10 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 10-4 APT5015BVFR_SVFR 60 ID, DRAIN CURRENT (AMPERES) VGS=6V, 7V, 8V, 10V & 15V ID, DRAIN CURRENT (AMPERES) 60 50 40 30 20 10 0 VGS=15V VGS=7V, 8V & 10V 6V 50 5.5V 40 30 5V 20 10 0 4.5V 4V 5.5V 5V 4.5V 4V 0 50 100 150 200 250 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) FIGURE 2, TYPICAL OUTPUT CHARACTERISTICS 60 ID, DRAIN CURRENT (AMPERES) RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE 0 2 4 6 8 10 12 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) FIGURE 3, TYPICAL OUTPUT CHARACTERISTICS 1.5 V GS TJ = -55°C VDS> ID (ON) x RDS (ON)MAX. 250µSEC. PULSE TEST @