MAX6369–MAX6374
Pin-Selectable Watchdog Timers
General Description
Benefits and Features
The MAX6369–MAX6374 are pin-selectable watchdog
timers that supervise microprocessor (μP) activity and
signal when a system is operating improperly. During
normal operation, the microprocessor should repeatedly
toggle the watchdog input (WDI) before the selected
watchdog timeout period elapses to demonstrate that
the system is processing code properly. If the μP does
not provide a valid watchdog input transition before the
timeout period expires, the supervisor asserts a watchdog
(WDO) output to signal that the system is not executing
the desired instructions within the expected time frame.
The watchdog output pulse can be used to reset the μP or
interrupt the system to warn of processing errors.
●● Precision Watchdog Timer for Critical μP Applications
●● Pin-Selectable Watchdog Timeout Periods
●● Pin-Selectable Watchdog Startup Delay Periods
●● Ability to Change Watchdog Timing Characteristics
Without Power Cycling
●● Open-Drain or Push-Pull Pulsed Active-Low
Watchdog Output
●● Watchdog Timer Disable Feature
●● +2.5V to +5.5V Operating Voltage
●● 8μA Low Supply Current
●● No External Components Required
The MAX6369–MAX6374 are flexible watchdog timer
supervisors that can increase system reliability through
notification of code execution errors. The family offers
several pin-selectable watchdog timing options to match
a wide range of system timing applications:
●● Miniature 8-Pin SOT23 Package
●● AEC-Q100 Qualified (MAX6369KA/V+ and
MAX6374KA/V+ Only)
Applications
●● Watchdog startup delay: provides an initial delay
before the watchdog timer is started.
●●
●●
●●
●●
●●
●●
●● Watchdog timeout period: normal operating watchdog
timeout period after the initial startup delay.
●● Watchdog output/timing options: open drain (100ms)
or push-pull (1ms).
Embedded Control Systems
Industrial Controllers
Critical μP and Microcontroller (μC) Monitoring
Automotive
Telecommunications
Networking
The MAX6369–MAX6374 operate over a +2.5V to +5.5V
supply range and are available in miniature 8-pin SOT23
packages.
Functional Diagram
VCC
WDI
MAX6369–MAX6374
TRANSITION
DETECTOR
SET 2
SET 1
SET 0
CONTROL
LOGIC
ENABLE
CLEAR
SET WATCHDOG TIMEOUT
SET STARTUP DELAY
WATCHDOG
TIMER CIRCUITRY
GND
19-1676; Rev 8; 7/17
EN
OUT
OUTPUT
WDO
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
Absolute Maximum Ratings
Terminal Voltage (with respect to GND)
VCC. .....................................................................-0.3V to +6V
WDI.......................................................................-0.3V to +6V
WDO (Open Drain: MAX6369/71/73)...................-0.3V to +6V
WDO (Push-Pull: MAX6370/72/74........ -0.3V to (VCC + 0.3V)
SET0, SET1, SET2............................... -0.3V to (VCC + 0.3V)
Maximum Current, Any Pin (input/output)...........................20mA
Continuous Power Dissipation (TA = +70°C)
8-Pin SOT23 (derate 8.75mW/°C above +70°C).........700mW
Operating Temperature Range.......................... -40°C to +125°C
Storage Temperature Range............................. -65°C to +150°C
Junction Temperature.......................................................+150°C
VCC Rise or Fall Rate....................................................0.05V/μs
Lead Temperature (soldering, 10s).................................. +300°C
Soldering Temperature (reflow)
Lead(Pb)-free...................................................................+260°C
Containing Lead (Pb).......................................................+240°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(VCC = +2.5V to +5.5V, SET_ = VCC or GND, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C and
VCC = +3V.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
Operating Voltage Range
VCC
Supply Current
ICC
No load
Input High Voltage
VIH
WDI, SET0, SET1, SET2
Input Low Voltage
VIL
Logic Input Current (Note 2)
VOL
WDO Leakage Current
ILKG
www.maximintegrated.com
VOH
TYP
2.5
WDI, SET0,
SET1, SET2
MAX
UNITS
5.5
V
TA = -40°C to +85°C
8
20
TA = -40°C to +125°C
10
22
0.8 x VCC
µA
V
VCC ≥ 3.3V,
TA = -40°C to +85°C
0.8
VCC ≥ 3.3V,
TA = -40°C to +125°C
0.6
VCC ≥ 2.5V,
TA = -40°C to +85°C
0.6
VCC ≥ 2.5V,
TA = -40°C to +125°C
0.4
V
VWDI or VSET_ = 0V or VCC
WDO Output Low
Voltage
WDO Output High
Voltage
MIN
±10
nA
ISINK = 1.2mA, VCC > 2.7V, watchdog
output asserted
0
0.3
V
ISINK = 6mA, VCC > 4.5V, watchdog output
asserted
0.4
V
1
µA
VWDO = 0 to +5.5V, output deasserted,
MAX6369/MAX6371/MAX6373
ISOURCE = 500µA, VCC > 2.7V,
watchdog output deasserted
0.8 x VCC
ISOURCE = 800µA, VCC > 4.5V,
watchdog output deasserted
VCC - 1.5
V
Maxim Integrated │ 2
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
Electrical Characteristics (continued)
(VCC = +2.5V to +5.5V, SET_ = VCC or GND, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C and
VCC = +3V.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
MAX6369/MAX6370
Startup Delay Period
Watchdog Timeout
Period
tDELAY
tWD
VSET2 = 0V, VSET1 = 0V, VSET0 = 0V
1
3
VSET2 = 0V, VSET1 = 0,V SET0 = VCC
10
30
VSET2 = 0V, SET1 = VCC, VSET0 = 0V
30
90
VSET2 = 0V, SET1 = VCC, SET0 = VCC
SET2 = VCC, VSET1 = 0V, VSET0 = 0V
Watchdog Disabled
100
300
SET2 = VCC, VSET1 = 0V, SET0 = VCC
1
3
SET2 = VCC, SET1 = VCC, VSET0 = 0V
10
30
SET2 = VCC, SET1 = VCC, SET0 = VCC
60
180
VSET2 = 0V, VSET1 = 0V, VSET0 = 0V
1
3
VSET2 = 0V, VSET1 = 0V, SET0 = VCC
10
30
VSET2 = 0V, SET1 = VCC, VSET0 = 0V
30
90
VSET2 = 0V, SET1 = VCC, SET0 = VCC
SET2 = VCC, VSET1 = 0V, VSET0 = 0V
ms
ms
s
ms
Watchdog Disabled
100
300
SET2 = VCC, VSET1 = 0V, SET0 = VCC
1
3
SET2 = VCC, SET1 = VCC, VSET0 = 0V
10
30
SET2 = VCC, SET1 = VCC, SET0 = VCC
60
180
ms
s
MAX6371/MAX6372
Startup Delay Period
Watchdog Time-Out
Period
tDELAY
tWD
VSET2 = 0V, SET1 = VCC, SET0 = VCC
Watchdog Disabled
All other SET_ conditions
60
180
VSET2 = 0V, VSET1 = 0V, VSET0 = 0V
1
3
VSET2 = 0V, VSET1 = 0V, SET0 = VCC
3
9
VSET2 = 0V, SET1 = VCC, VSET0 = 0V
10
30
VSET2 = 0V, SET1 = VCC, SET0 = VCC
s
ms
Watchdog Disabled
SET2 = VCC, VSET1 = 0V, VSET0 = 0V
100
300
SET2 = VCC, VSET1 = 0V, SET0 = VCC
300
900
SET2 = VCC, SET1 = VCC, VSET0 = 0V
3
9
SET2 = VCC, SET1 = VCC, SET0 = VCC
60
180
VSET2 = 0V, VSET1 = 0V, VSET0 = 0V
3
9
VSET2 = 0V, VSET1 = 0V, SET0 = VCC
3
9
VSET2 = 0V, SET1 = VCC, VSET0 = 0V
60
180
ms
s
MAX6373/MAX6374
Startup Delay Period
tDELAY
SET2 = 0V, SET1 = VCC, SET0 = VCC
SET2 = VCC, VSET1 = 0V, VSET0 = 0V
www.maximintegrated.com
s
Watchdog Disabled
200
600
SET2 = VCC, VSET1 = 0V, SET0 = VCC
First Edge (Note 3)
SET2 = VCC, SET1 = VCC, VSET0 = 0V
First Edge (Note 3)
SET2 = VCC, SET1 = VCC, SET0 = VCC
ms
60
180
µs
s
Maxim Integrated │ 3
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
Electrical Characteristics (continued)
(VCC = +2.5V to +5.5V, SET_ = VCC or GND, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C and
VCC = +3V.) (Note 1)
PARAMETER
SYMBOL
Watchdog Timeout
Period
tWD
Watchdog Input Pulse Width
(Note 2)
tWDI
Watchdog Output Pulse Width
tWDO
Internal Setup Time
(Note 4)
tSETUP
MAX
UNITS
VSET2 = 0V, VSET1 = 0V, VSET0 = 0V
CONDITIONS
MIN
3
TYP
9
ms
VSET2 = 0V, VSET1 = 0V, SET0 = VCC
3
9
VSET2 = 0V, SET1 = VCC, VSET0 = 0V
1
3
VSET2 = 0V, SET1 = VCC, SET0 = VCC
Watchdog Disabled
s
SET2 = VCC, VSET1 = 0V, VSET0 = 0V
30
90
SET2 = VCC, VSET1 = 0V, SET0 = VCC
1
3
µs
SET2 = VCC, SET1 = VCC, VSET0 = 0V
10
30
SET2 = VCC, SET1 = VCC, SET0 = VCC
10
30
After WDO deasserted
100
MAX6369/MAX6371/MAX6373
100
300
ms
MAX6370/MAX6372/MAX6374
1
3
ms
300
µs
s
ns
After WDO deasserted
Note 1: Production tested at TA = +25°C. Guaranteed by design over temperature limits.
Note 2: Guaranteed by design.
Note 3: In this setting the watchdog timer is inactive and startup delay ends when WDI sees its first level transition. See the
Selecting Device Timing section for more information.
Note 4: After power-up, or a setting change, there is an internal setup time during which WDI is ignored.
Typical Operating Characteristics
(Circuit of Functional Diagram, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT
vs. TEMPERATURE
SUPPLY CURRENT (µA)
12
VCC = +5.5V
10
8
VCC = +2.5V
6
4
-40
-15
10
35
TEMPERATURE (°C)
www.maximintegrated.com
60
85
1.003
MAX6369/74-02
MAX6369/74-01
14
NORMALIZED WATCHDOG TIMEOUT PERIOD
WATCHDOG TIMEOUT PERIOD
vs. TEMPERATURE
1.002
1.001
1.000
0.999
0.998
0.997
-40
-15
10
35
60
85
TEMPERATURE (°C)
Maxim Integrated │ 4
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
Pin Configuration
TOP VIEW
WDI 1
GND 2
N.C.
3
SET0 4
MAX6369
MAX6370
MAX6371
MAX6372
MAX6373
MAX6374
8
VCC
7
WDO
6
SET2
5
SET1
SOT23
Pin Description
PIN
NAME
FUNCTION
1
WDI
Watchdog Input. If WDI remains either high or low for the duration of the watchdog timeout period (tWD),
WDO triggers a pulse. The internal watchdog timer clears whenever a WDO is asserted or whenever
WDI sees a rising or falling edge.
2
GND
Ground
3
N.C.
Not Connected. Do not make any connection to this pin.
4
SET0
Set Zero. Logic input for selecting startup delay and watchdog timeout periods. See Table 1 for timing details.
5
SET1
Set One. Logic input for selecting startup delay and watchdog timeout periods. See Table 1 for timing details.
6
SET2
Set Two. Logic input for selecting startup delay and watchdog timeout periods. See Table 1 for timing details.
7
WDO
Watchdog Output. Pulses low for the watchdog output pulse width, tWDO, when the internal watchdog
times out. The MAX6369/MAX6371/MAX6373 have open-drain outputs and require a pull-up resistor.
The MAX6370/MAX6372/MAX6374 outputs are push-pull.
8
VCC
Supply Voltage (+2.5V to +5.5V)
www.maximintegrated.com
Maxim Integrated │ 5
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
Detailed Description
The MAX6369–MAX6374 are flexible watchdog circuits
for monitoring μP activity. During normal operation, the
internal timer is cleared each time the μP toggles the
WDI with a valid logic transition (low to high or high to
low) within the selected timeout period (tWD). The WDO
remains high as long as the input is strobed within the
selected timeout period. If the input is not strobed before
the timeout period expires, the watchdog output is asserted
low for the watchdog output pulse width (tWDO). The
device type and the state of the three logic control pins
(SET0, SET1, and SET2) determine watchdog timing
characteristics. The three basic timing variations for the
watchdog startup delay and the normal watchdog timeout
period are summarized below (see Table 1 for the timeout
characteristics for all devices in the family):
●● Watchdog Startup Delay:
Provides an initial delay before the watchdog timer is
started.
Allows time for the μP system to power up and initialize
before assuming responsibility for normal watchdog
timer updates.
Includes several fixed or pin-selectable startup delay
options from 200μs to 60s, and an option to wait for
the first watchdog input transition before starting the
watchdog timer.
Table 1. Minimum Timeout Settings
LOGIC INPUTS
MAX6369/MAX6370
MAX6371/MAX6372
SET2
SET1
tDELAY, tWD
tDELAY = 60s, tWD
tDELAY
tWD
0
0
0
1ms
1ms
3ms
3ms
0
0
1
10ms
3ms
3s
3s
0
1
0
30ms
10ms
60s
1s
0
1
1
Disabled
Disabled
Disabled
Disabled
1
0
0
100ms
100ms
200µs
30µs
1
0
1
1s
300ms
First Edge
1s
1
1
0
10s
3s
First Edge
10s
1
1
1
60s
60s
60s
10s
SET0
www.maximintegrated.com
MAX6373/MAX6374
Maxim Integrated │ 6
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
●● Watchdog Timeout Period:
Normal operating watchdog timeout period after the
initial startup delay.
A watchdog output pulse is asserted if a valid watchdog input transition is not received before the timeout
period elapses.
Eight pin-selectable timeout period options for each
device, from 30μs to 60s.
Pin-selectable watchdog timer disable feature.
●● Watchdog Output/Timing Options:
Open drain, active low with 100ms minimum watchdog
output pulse (MAX6369/MAX6371/MAX6373).
Push-pull, active low with 1ms minimum watchdog
output pulse (MAX6370/MAX6372/MAX6374).
Each device has a watchdog startup delay that is initiated
when the supervisor is first powered or after the user
modifies any of the logic control set inputs. The watchdog timer does not begin to count down until the
completion of the startup delay period, and no watchdog
output pulses are asserted during the startup delay. When
the startup delay expires, the watchdog begins counting its
normal watchdog timeout period and waiting for WDI transitions.
The startup delay allows time for the μP system to power
up and fully initialize before assuming responsibility for the
normal watchdog timer updates. Startup delay periods vary
between the different devices and may be altered by the
logic control set pins. To ensure that the system generates
VCC
tSETUP
tDELAY
no undesired watchdog outputs, the routine watchdog input
transitions should begin before the selected minimum startup
delay period has expired.
The normal watchdog timeout period countdown is initiated
when the startup delay is complete. If a valid logic transition
is not recognized at WDI before the watchdog timeout
period has expired, the supervisor asserts a watchdog
output. Watchdog timeout periods vary between the different
devices and may be altered by the logic control set pins.
To ensure that the system generates no undesired watchdog outputs, the watchdog input transitions should occur
before the selected minimum watchdog timeout period
has expired.
The startup delay and the watchdog timeout period are
determined by the states of the SET0, SET1, and SET2
pins, and by the particular device within the family. For
the MAX6369 and MAX6370, the startup delay is equal
to the watchdog timeout period. The startup and watchdog timeout periods are pin selectable from 1ms to 60s
(minimum).
For the MAX6371 and MAX6372, the startup delay is fixed
at 60s and the watchdog timeout period is pin selectable
from 1ms to 60s (minimum).
The MAX6373/MAX6374 provide two timing variations
for the startup delay and normal watchdog timeout. Five
of the pin-selectable modes provide startup delays from
200μs to 60s minimum, and watchdog timeout delays
from 3ms to 10s minimum. Two of the selectable modes
tWD
tWD
tWD
WDI
A
A
B
C
D
E F
WDO
G
E
tWDO
A TRANSITIONS ON WDI IGNORED DURING SETUP DELAY.
B TRANSITION(S) ON WDI IGNORED DURING STARTUP DELAY PERIOD.
C WATCHDOG TIMER STARTS AFTER STARTUP DELAY AND WDO IS DEASSERTED.
D TRANSITION OCCURS BEFORE WATCHDOG TIMEOUT PERIOD. WATCHDOG
TIMER CLEARS AND STARTS TIMER AGAIN.
E WATCHDOG TIMES OUT, WDO ASSERTS.
F TRANSITIONS ON WDI IGNORED WHEN WDO ASSERTED.
G WATCHDOG TIMER STARTS AFTER WDO DEASSERTS.
Figure 1. Watchdog Timing
www.maximintegrated.com
Maxim Integrated │ 7
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
do not initiate the watchdog timer until the device receives
its first valid watchdog input transition (there is no fixed
period by which the first input must be received). These
two extended startup delay modes are useful for applications
requiring more than 60s for system initialization.
All the MAX6369–MAX6374 devices may be disabled with
the proper logic control pin setting (Table 1).
Applications Information
Input Signal Considerations
Watchdog timing is measured from the last WDI rising
or falling edge associated with a pulse of at least 100ns
in width. WDI transitions are ignored when WDO is
asserted, and during the startup delay period (Figure 1).
Watchdog input transitions are also ignored for a setup
period, tSETUP, of up to 300μs after power-up or a setting
change (Figure 2).
Selecting Device Timing
SET2, SET1, and SET0 program the startup delay and
watchdog timeout periods (Table 1). Timeout settings
can be hard wired, or they can be controlled with logic
gates and modified during operation. To ensure smooth
transitions, the system should strobe WDI immediately
before the timing settings are changed. This minimizes
the risk of initializing a setting change too late in the timer
countdown period and generating undesired watchdog
outputs. After changing the timing settings, two outcomes
are possible based on WDO. If the change is made while
WDO is asserted, the previous setting is allowed to finish, the
characteristics of the new setting are assumed, and the
new startup phase is entered after a 300μs setup time
(tSETUP) elapses. If the change is made while WDO is not
asserted, the new setting is initiated immediately, and the
new startup phase is entered after the 300μs setup time
elapses.
Selecting 011 (SET2 = 0, SET1 = 1, SET0 = 1) disables
the watchdog timer function on all devices in the family.
Operation can be reenabled without powering down by
changing the set inputs to the new desired setting. The
device assumes the new selected timing characteristics
and enter the startup phase after the 300μs setup time
elapses (Figure 2). WDO is high when the watchdog timer
is disabled.
The MAX6373/MAX6374 offer a first-edge feature. In firstedge mode (settings 101 or 110, Table 1), the internal timer
does not control the startup delay period. Instead, startup
terminates when WDI sees a transition. If changing to firstedge mode while the device is operating, disable mode
must be entered first. It is then safe to select first-edge
mode. Entering disable mode first ensures the output is
unasserted when selecting first-edge mode and removes
the danger of WDI being masked out.
Output
The MAX6369/MAX6371/MAX6373 have an active-low,
open-drain output that provides a watchdog output pulse
of 100ms. This output structure sinks current when WDO
is asserted. Connect a pullup resistor from WDO to any
supply voltage up to +5.5V.
Select a resistor value large enough to register a logic
low (see Electrical Characteristics), and small enough
to register a logic high while supplying all input current
and leakage paths connected to the WDO line. A 10kΩ
pullup is sufficient in most applications. The MAX6370/
MAX6372/MAX6374 have push-pull outputs that provide
an active-low watchdog output pulse of 1ms. When WDO
deasserts, timing begins again at the beginning of the
watchdog timeout period (Figure 1).
tWD
WDI
*
WDO
*
*
*
*
tWD
tWD
SET_
*IGNORED EDGE
tSETUP
tDELAY
tWD
tSETUP
tDELAY
tWD
Figure 2. Setting Change Timing
www.maximintegrated.com
Maxim Integrated │ 8
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
Usage in Noisy Environments
If using the watchdog timer in an electrically noisy environment, a bypass capacitor of 0.1μF should be connected between VCC and GND as close to the device as
possible, and no further away than 0.2 inches.
Watchdog Software
Considerations
To help the watchdog timer monitor software execution
more closely, set and reset the watchdog input at different
points in the program, rather than pulsing the watchdog
input high-low-high or low-high-low. This technique avoids
a stuck loop, in which the watchdog timer would continue
to be reset inside the loop, keeping the watchdog from
timing out. Figure 3 shows an example of a flow diagram
where the I/O driving the watchdog input is set high at
the beginning of the program, set low at the end of every
subroutine or loop, then set high again when the program
returns to the beginning. If the program should hang in
any subroutine, the problem would be quickly corrected,
since the I/O is continually set low and the watchdog timer
is allowed to time out, causing WDO to pulse.
www.maximintegrated.com
START
SET WDI
HIGH
PROGRAM
CODE
SUBROUTINE OR
PROGRAM LOOP
POSSIBLE
INFINITE LOOP PATH
SET WDI LOW
RETURN
Figure 3. Watchdog Flow Diagram
Maxim Integrated │ 9
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
Selector Guide
PART
OUTPUT
WDO PULSE
WIDTH (ms)
MAX6369
Open Drain
100
Selectable: 1ms to 60s
Selectable: 1ms to 60s
MAX6370
Push-Pull
1
MAX6371
Open Drain
MAX6372
Push-Pull
MAX6373
Open Drain
MAX6374
Push-Pull
MINIMUM STARTUP DELAY
Selectable: 1ms to 60s
Selectable: 1ms to 60s
100
60s
Selectable: 1ms to 60s
1
60s
Selectable: 1ms to 60s
100
Selectable: 200µs to 60s or first edge
Selectable: 30µs to 10s
1
Selectable: 200µs to 60s or first edge
Selectable: 30µs to 10s
Ordering Information
TEMP
RANGE
PART
Package Information
PINPACKAGE
TOP
MARK
AADC
MAX6369KA+T
-40°C to +125°C
8 SOT23
MAX6369KA-T
-40°C to +125°C
8 SOT23
AADC
MAX6369KA/V+T
-40°C to +125°C
8 SOT23
AEQV
MAX6370KA+T
-40°C to +125°C
8 SOT23
AADD
MAX6371KA+T
-40°C to +125°C
8 SOT23
AADE
MAX6372KA+T
-40°C to +125°C
8 SOT23
AADF
MAX6373KA+T
-40°C to +125°C
8 SOT23
AADG
MAX6373KA-T
-40°C to +125°C
8 SOT23
AADG
MAX6374KA+T
-40°C to +125°C
8 SOT23
AADH
MAX6374KA/V+T
-40°C to +125°C
8 SOT23
AADH
Note: All devices are available in tape-and-reel only. Required
order increment is 2,500 pieces.
/V denotes an automotive qualified part.
Devices are available in both leaded and lead(Pb)-free
packaging.
+Denotes Lead(Pb)-free packages and - denotes leaded
packages.
www.maximintegrated.com
MINIMUM WATCHDOG TIMEOUT
For the latest package outline information and land patterns
(footprints), go to www.maximintegrated.com/packages. Note
that a “+”, “#”, or “-” in the package code indicates RoHS status
only. Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
8 SOT23
K8SN+1,
K8SN-1
21-0078
90-0176
Chip Information
TRANSISTOR COUNT: 1500
PROCESS: BiCMOS
Maxim Integrated │ 10
MAX6369–MAX6374
Pin-Selectable Watchdog Timers
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
CHANGED
0
4/00
Initial release
—
1
7/00
Removed future product asterisk for MAX6370.
1
2
2/03
Corrected limits in Electrical Characteristics.
4
3
12/05
Added lead-free information to Ordering Information.
1
4
6/10
Revised the Ordering Information, Absolute Maximum Ratings, Electrical
Characteristics, and the Selecting Device Timing section.
5
1/11
Updated the top mark information in the Ordering Information section.
1
6
3/15
Deleted minimum value for Internal Setup Time in Electrical Characteristics and
changed units from ms to µs
4
7
8
1/16
7/17
Added lead-free part numbers and package codes
Added AEC-Q100 Qualified statement to Benefits and Features section
DESCRIPTION
1, 2, 8
9, 1
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2017 Maxim Integrated Products, Inc. │ 11
工商网监
湘ICP备2023018690号
