MASWSS0204TR-3000

MASWSS0204 GaAs SPDT 2.7 V High Power Switch DC - 3.0 GHz Features • • • • • • • • • Low Voltage Operation: 2.7 V High IP3: +56 dBm Low Insertion Loss: 0.30 dB at 1 GHz High Isolation: 25 dB at 1 GHz 0.5 micron GaAs PHEMT Process Lead-Free SC70 Package Halogen-Free “Green” Mold Compound 260°C Reflow Compatible RoHS* Compliant Version of MASWSS0117 Rev. V2 Functional Block Diagram Description M/A-COM’s MASWSS0204 is a GaAs PHEMT MMIC single pole double throw (SPDT) high power switch in a low cost SC70 six lead package. The MASWSS0204 is ideally suited for applications where high power, low control voltage, low insertion loss, high isolation, small size and low cost are required. Typical applications are for CDMA handset systems that connect separate transceiver and/or GPS functions to a common antenna, as well as other related handset and general purpose applications. The MASWSS0204 can be used in all systems operating up to 3 GHz requiring high power at low control voltage. The MASWSS0204 is fabricated using a 0.5 micron gate length GaAs PHEMT process. The process features full passivation for performance and reliability. Pin Configuration Pin No. 1 2 3 4 5 6 Pin Name V2 RFC V1 RF1 GND RF2 Description Vcontrol 2 RF Common Vcontrol 1 RF Port 1 RF Ground RF Port 2 MASWSS0204 orientation in tape Ordering Information 1,2 Part Number MASWSS0204 MASWSS0204TR-3000 MASWSS0204SMB Package Bulk Packaging 3000 piece reel Sample Test Board Note: Device supplied on tape and reel is the reverse orientation of that shown in Application Note M513. 1. Reference Application Note M513 for reel size information. 2. All sample boards include 5 loose parts. * Restrictions on Hazardous Substances, European Union Directive 2002/95/EC. 1 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASWSS0204 GaAs SPDT 2.7 V High Power Switch DC - 3.0 GHz Electrical Specifications: TA = 25°C, Vc = 0 V/2.7 V, Z0 = 50 Ω 3 Parameter Insertion Loss4 Test Conditions DC – 1 GHz 1 – 2 GHz 2 - 3 GHz DC – 1 GHz 1 – 2 GHz 2 - 3 GHz DC – 3 GHz 825 MHz Two Tone, +24 dBm Total Pin, 5 MHz Spacing For Cell Band: Two-tone signal input: Tx1 = +22 dBm @ 820 MHz, Tx2 = +22 dBm @ 821 MHz, RX interfere = -23 dBm @ 869 MHz. For PCS Band: Two-tone signal input: Tx1 = +18 dBm @ 1880 MHz, Tx2 = +18 dBm @ 1881 MHz, RX interfere = -23 dBm @ 1960 MHz. P0.1dB Trise, Tfall Ton, Toff Transients Control Current 1 GHz 10% to 90% RF, 90% to 10% RF 50% control to 90% RF, 50% control to 10% RF In Band VC = 2.7 V Units dB dB dB dB dB dB dB dBm Min. — — — 23 — — — — — Typ. 0.30 0.35 0.35 25 19 15 20 56 Max. 0.65 — — — — — — — Rev. V2 Isolation Return Loss IP3 dBm -99 — Cross Modulation dBm dBm ns ns mV µA — — — — — — -94 38 70 100 25 5 — — — — — 20 3. For positive voltage control, external DC blocking capacitors are required on all RF ports. 4. Insertion loss can be optimized by varying the DC blocking capacitor value, e.g. 1000 pF for 100 MHz - 1 GHz, 39 pF for 0.5 - 3 GHz. Absolute Maximum Ratings 5,6 Parameter Input Power (0.5 - 3 GHz, 3 V Control) Operating Voltage Operating Temperature Storage Temperature Absolute Maximum +38 dBm +8.5 volts -40°C to +85°C -65°C to +150°C Truth Table 7,8,9 V1 1 0 V2 0 1 ANT– RF1 On Off ANT - RF2 Off On 5. Exceeding any one or combination of these limits may cause permanent damage to this device. 6. M/A-COM does not recommend sustained operation near these survivability limits. 7. For positive voltage control, external DC blocking capacitors are required on all RF ports. 8. Differential voltage, V(state 1) - V(state 0), must be +2.7 V minimum, but must not exceed 8.5 V. 9. 0 = -5 V to +2.3 V, 1 = -2.3 V to +5 V. 2 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASWSS0204 GaAs SPDT 2.7 V High Power Switch DC - 3.0 GHz Typical Performance Curves, 39 pF Insertion Loss 0.6 +25°C +85°C -40°C Rev. V2 Lead-Free SC70 Plastic Package† 0.5 0.4 0.3 0.2 0.1 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Frequency (GHz) Isolation 40 † 30 +25°C +85°C -40°C Reference Application Note M538 for lead-free solder reflow recommendations. Meets JEDEC moisture sensitivity level 1 requirements. Plating is 100% matte tin over copper. 20 Qualification 10 Qualified to M/A-COM specification REL-201, Process Flow –2. 1.0 1.5 2.0 2.5 3.0 0 0.5 Handling Procedures Please observe the following precautions to avoid damage: Frequency (GHz) Return Loss 0 5 10 15 20 25 30 35 0.0 +25°C +85°C -40°C Static Sensitivity Gallium Arsenide Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these devices. 1.0 2.0 3.0 4.0 5.0 6.0 Frequency (GHz) 3 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice.