IS18WWC1W-K

Toggles OLED Rocker DISTINCTIVE CHARACTERISTICS Rockers • Organic LED technology in display rocker • Multi-function programmable device: select with rocker, push for activation • Broad display aids in navigation, both forward and reverse and up and down, in structured menus • Wide viewing angle of 180° and large 0.92” display with exceptional contrast • Conforms to IP64 of IEC 60529 Standards on panel surface; dust tight construction of switch prevents entry of dust and improves contact reliability • Commands and data supplied via serial communications protocol (SPI) • Long life OLED with 52,000 hours at 30% illumination E • High reliability and long mechanical and electrical life of one million actuations minimum Keylocks • Stylish black housing design with matte finish complements any application Programmable Illuminated PB Pushbuttons • Replaces multiple switches and displays with one device in a small package Rotaries Monochrome OLED featuring sharp contrast and high resolution with 96 x 64 pixels Slides Panel mount with easy, snap-in installation Tactiles Short 14.6mm (.575”) behind-panel height for compact spaces Touch Tilt Actual Size Description Accessories Part Number Indicators SWITCH PART NUMBER & DESCRIPTION OLED Rocker Switch: SP3T Switch Rocker (ON) (ON) (ON) Pushbutton Normally OFF Supplement IS18WWC1W www.nkkswitches.com E15 03/16/20 Toggles OLED Rocker SWITCH SPECIFICATIONS Circuit Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Contact Position E Contact Resistance 200 milliohms maximum Insulation Resistance 500 megohms minimum @ 250V DC Dielectric Strength 250V AC for 1 minute minimum Electrostatic Resisting Pressure 15kV minimum Mechanical Endurance 1,000,000 operations minimum Electrical Endurance 1,000,000 operations minimum Operating Force 5± 2 Newtons at center of cap; 3.7± 1.7 Newtons at top and bottom Total Travel 1.3± 0.5mm (.051”± .020") at center of cap; 1.8± 0.6mm (.071”±.024") at top and bottom OLED SPECIFICATIONS Characteristics of Display Display Device Single color OLED display Display Mode Passive matrix Pixel Format 96 x 64 pixels (horizontal x vertical) Pixel Size 0.16mm x 0.177mm (horizontal x vertical) Interface Serial (SPI) interface Color White/Black (normally White) Splash & Dust Proof Conforms to IP64 of IEC60529 standards on panel surface Operating Temperature Range –20°C ~ +70°C (–4°F ~ +158°F) Storage Temperature Range –25°C ~ +80°C (–13°F ~ +176°F) Operating Life Time (Display) 52,000 hours (30% brightness); 15,600 hours (100% brightness) Absolute Maximum Ratings (Temperature at 25°C) Symbols Recommended Operating Conditions Ratings Items Symbols Minimum Typical Maximum VDDA 2.7V 2.8V 3.6V Supply Voltage for Drive VAH 14.5V 15.0V 15.5V Input High Level Voltage VI H 0.75 x VDDA –– VDDA Input Low Level Voltage VI L 0.0 –– 0.25V x VDDA VI H 0.80 x VDDA –– VDDA VI L 0.0 –– 0.20V x VDDA Supply Voltage for Logic/Interface VDDA –0.3V to +3.6V Supply Voltage for Logic/Interface Supply Voltage for Drive VAH –0.3V to +18.0V Input Voltage Vin –0.3V to VDDA +0.3V Tilt Touch Indicators Accessories Down (ON) 11-12 3VA maximum @ 24V DC maximum (Applicable Range 10mA ~ 125mA @ 0.1V ~ 24V DC) Input High Level Voltage (XRES only) Input Low Level Voltage (XRES only) Current Consumption (Temperature at 25°C, VDDA = 2.8V, VAH = 15.0V) Items Supplement Bottom Normal OFF Electrical Capacity (Resistive Load) Items Tactiles Single Pole Three Throw (Momentary) Top Center Normal Down Normal Down OFF (ON) 9-12 OFF (ON) 10-12 Optical Characteristics Symbols Min Typical Max –– 8.3mA All-Pixels-On Mode *Drive System Power Current I H1 All-Pixels-On Mode *Logic/IF System Power Current I DD1 Sleep Mode **Drive System Power Current I H2 –– –– 10μA Sleep Mode **Logic/IF System Power Current I DD2 –– –– 10μA 6.9mA Items Brightness –– 0.3mA 0.36mA Chromaticity Contrast * All pixels shall be turned on with the maximum level gray scale ** All pixels shall be turned off (while chip is operating) E16 (Temperature at 25°C, Initial Value: depends on initial setting) Minimum Typical 75 cd/m 100 cd/m 2 Maximum 2 125 cd/m2 (x) ***2 0.310 ***2 (y) ***2 0.330 ***2 100 –– –– *** Chromaticity range is the area of the ellipse. (See Chromaticity Diagram next page.) The ellipse passes through points A, B, C and D and designates the center of each side of the quadrangle. www.nkkswitches.com 0.39 0.3105 D 0.3193 0.3088 TIMING SPECIFICATIONS AC Characteristics (Temperature at –20°C ~ +70°C), VDDA = 2.8V, VAH = 16V Symbols Minimum Typical Maximum Items Clock Cycle Time t c yc le 100ns –– –– A0 Setup Time t SWDS 65ns –– –– A0 Hold Time t SWDH 35ns –– –– XCS Setup Time t CWS 65ns –– –– XCS Hold Time t CWH 35ns –– –– High Level XCS Pulse Width t CSBH *30ns –– –– Rockers 0.3552 0.2561 D C 0.25 0.27 0.29 0.31 0.33 Chromaticity X 0.35 Pushbuttons 0.3007 0.37 A0 tSWDS t SWDH t C WS t CWH XCS E tCSBH tR Write Data Setup Time t WDTS 10ns –– –– Write Data Hold Time t WDTH 30ns –– –– SCL Low Time t SCLL 45ns –– –– SCL High Time t SCLH 45ns –– –– SCL Rise Time tr –– –– 15ns SCL Fall Time tf –– –– 15ns t SC L H t c yc le SCL tF t SC L L t WDTS SI t WDTH D7 * Requires more than 100ns after resetting software D6 D5 D4 D3 D2 D1 D0 Black & White OLED Panel 96 x 64 SEG1 . . . SEG96 COM1 . . . COM64 BLOCK DIAGRAM & PIN CONFIGURATIONS Segment Driver VDDA 1 VAH 8 XRES 2 SCL XCS SI A0 5 3 6 4 Common Driver OLED Driver with Controller Light Decoder Display Control & Screen Saver Graphic Display Data RAM 128 x 64 x 1 Bit I/F Circuit Block Programmable Illuminated PB B C A B Keylocks 0.3535 Rotaries Chromaticity Y 0.3639 Oscillator Timing Control Tactiles Chromaticity X A Chromaticity Y Point 0.38 0.37 0.36 0.35 0.34 0.33 0.32 0.31 0.30 0.29 0.28 0.27 0.26 0.25 Slides Chromaticity Diagram Toggles OLED Rocker Register 5 6 SCL SI VSS VAH SW1 SW2 SW3 SW_COM 7 8 9 10 11 12 A0 Logic Type Power Source Reset Chip Select Touch VDDA XRES XCS Function Terminal to initialize IC built-in logic; initializes with low level Slave select for SPI. This line is active low. Address Terminal to input control signals of command/parameter Set low at time of command input and high level at the time of parameter input. Serial Clock Serial Data Input Ground Drive Type Power Source Switch Terminal 1 Switch Terminal 2 Switch Terminal 3 Switch Common Terminal Read command/parameter at time of SCL signal standing up Terminal to input command/parameter by SPI Indicators 1 2 3 4 Name Accessories Symbol N/O N/O N/O www.nkkswitches.com Supplement Pin No. 9 SW1 10 SW2 11 SW3 SW_COM 12 IS18WWC1W Tilt VSS 7 E17 Toggles OLED Rocker TYPICAL SWITCH DIMENSIONS (21.8) .858 Pushbuttons (38.8) 1.528 (13.22) .520 (15.3) .602 (50.7) 1.996 E NKK P/N This Side (30.6) 1.205 (46.7) 1.839 (35.1) 1.382 (2.0) .079 (37.9) 1.492 Keylocks Programmable Illuminated PB (35.4) 1.394 (19.16) .754 Rockers See Pixel Detail (0.8) .031 (5.6) .220 (14.6) .575 (34.9) 1.374 12 11 10 (0.04) Typ .0016 Rotaries (0.16) Typ .0063 Panel Thickness Range Slides (0.177) Typ .0070 (0.03) Typ .0012 3 2 1 Terminal Connector Detail Tactiles Pixel Detail (48.6) 1.913 .039 ~ .157" (1.0mm ~ 4.0mm) (35.4) 1.394 Tilt STATE TRANSITION State 0 Power OFF (VAH, VDDA OFF) 2 : Power OFF 8 : Initialization Touch 7 : Power OFF 6 : VAH ON State 0 1 : Power ON, Initialization State 1 Display OFF (Sleep Mode) 5 : VAH OFF Initialization Setting 3 : Display ON 9 : Changing the Display VDDA 4 : Display OFF State Number E18 State 9 : Changing the Display Display Sleep VAH 9 : Changing the Display VDDA Power ON State 1 ( State 3) State 2 Power OFF 2.5V State 2 Display ON XRES Supplement Accessories Indicators State 3 Power Saver Mode Power ON/OFF Sequence Changing the Display 0 Power OFF OFF –– OFF OFF Disable 1 Display OFF OFF ON ON ON Enable 2 Display ON ON OFF ON ON Enable 3 Power Saver OFF ON OFF ON Enable 2.5V 0V Reset low pulse width Trw (minimum 1µs) “L” www.nkkswitches.com Waiting time for oscillation stability (about 1.1ms) (VDDA x 0.8)V Completion time of reset Tr (minimum 0.1µs) Waiting time to stabilize VAH Level VAH voltage: 1s (reference) Minimum 0µs 0µs min “L” A0 “L” SCL/SI Reset low pulse width Trw (minimum 1µs) (VDDA x 0.2)V Minimum 0µs Waiting time to stabilize VAH voltage: 1ms (reference) VAH 0V XCS State 0 “Hi-z” 0µs min “H” or “L” “H” or “L” “H” or “L” Toggles OLED Rocker STATE TRANSITION (CONTINUED) 5 VAH OFF 6 VAH ON 7 Power OFF Display ON OFF Minimum 10ms ON Wait until VAH becomes stable Standby OFF Refer to "Power ON/OFF Sequence" Initialization Minimum 0µs Waiting time to stabilize VAH voltage: 1ms (Reference) Minimum 0µs VAH Refer to "Initialization Setting" Image 9 2.8V Minimum 0µs 15V 0V E 96 x 64 Image Data Sending Display Rewriting Change Display Dimmer/Screen Saver/Indication Settings 180° Reversal Keylocks 8 Rockers Display OFF VDDA INITIALIZITION SETTING Command Name Command Parameter Remarks Address (1 or 2Byte) Software Reset 01 Dot Matrix Display ON/OFF 02 00 Read/Write Operation Wetting 07 Display Direction Set Command Command Name Command Parameter Remarks Address (1 or 2Byte) 38 00 Note 1 Note 1 Y Axis Reading Start Address 39 00 Note 1 00 Note 1 Reserved 9 48 03 Note 2 09 00 Note 1 Reserved 1 10 03 Note 2 Screen Saver Event Timer Setting Command C3 00 Note 1 Reserved 2 12 63 Note 2 C4 00 Note 1 Reserved 3 13 00 Note 2 Screen Saver Event Timer Setting Command Dot Matrix Display Standby ON/OFF 14 00 One Time, Repeat or Direction Setting for Screen Saver CC 00 Note 1 Reserved 4 16 00 Note 2 Start/Stop Setting for Screen Saver CD 00 Note 1 Reserved 5 17 00 Notes 1 & 2 System Clock Division Ratio Setting D0 80 Note 2 Reserved 6 18 09 Note 2 Reserved 7 1A 04 Notes 1 & 2 Setting the STBY Pin D2 00 Notes 1 & 2 Reserved 8 1C 00 Notes 1 & 2 DACA Setting D4 00 Note 2 Graphic Memory Writing Direction 1D 00 Note 1 DACB Setting D5 00 Note 2 Setting Column Output Range 30 005F Note 1 DACC Setting D6 00 Note 2 Setting Row Output Range 32 003F Note 1 DACD Setting D7 00 Note 2 X Axis Reading/Writing Start Point 34 00 Note 1 Reserved 10 D9 00 Notes 1 & 2 X Axis Reading/Writing End Point 35 0B Note 1 Dimmer Setting DB 0F Note 1 Y Axis Reading/WritingStart Point 36 00 Note 1 Reserved 11 DD 88 Note 2 Y Axis Reading/Writing End Point 37 3F Note 1 Image Writing 08 Image data 2. Do not change setting value Supplement X Axis Reading Start Address Notes: 1. Same as default value Pushbuttons 4 Refer to "Display ON/OFF Sequence" Programmable Illuminated PB Display ON State 2 Display State 1 VAH OFF State 3 VAH ON State 1 Display State 2 OFF ON Notes: 1. Same as default value 2. Do not change setting value www.nkkswitches.com Rotaries 3 Refer to "Initialization Setting" Refer to "Power ON/OFF Sequence" Slides Power OFF Display ON/OFF Sequence Tactiles 2 Refer to "Power ON/OFF Sequence" Tilt Power ON Touch 1 Reference or Setting Procedure Indicators Transition Accessories State Transition E19 Toggles OLED Rocker ACCESSORIES (500.0) +50.0 – 0.0 19.685 PRECAUTIONS FOR HANDLING & STORAGE OF OLED ROCKERS E Handling ATTENTION ELECTROSTATIC SENSITIVE DEVICES 1. OLED devices are electrostatic sensitive. 2. Signal input under conditions not recommended may cause damage to the OLED unit or deterioration of the display. Follow directions regarding supply sequences of power and signal voltages. Keylocks Programmable Illuminated PB Pushbuttons Rockers AT715 Cable for Connection 3. If the OLED panel is broken, avoid touching the contents. Wash off in case of contact to the skin or clothing. Rotaries 4. Limit operating force to 100.0N maximum, as excessive pressure may damage the display. 5. Under certain actuation conditions, one side of the rocker and the center switch can both send actuation signals. Slides 6. Pixels acquire diminished brightness over time and use, and those most frequently habituated have greater reduction of brightness than those less used. To minimize this difference, operate OLED unit so that all pixels are used as consistently as possible. 7. Clean actuator surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. Tactiles Storage 1. Store in original container and away from direct sunlight. 2. Keep away from static electricity. Tilt 3. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination. Incorrect Correct Gasket position must be even with no gaps beneath bezel Gasket secure and flush against bezel Panel Mounting Touch • Before snapping a switch into the panel, align the gasket evenly under the bezel of the switch. Indicators • When mounting into a panel, apply equal pressure to sides of bezel and insert parallel to the panel. • After mounting, be sure there are no gaps between switch and panel. Lightly push into panel. • After installing into panel, do not apply excessive force. Accessories • After panel installation and wiring is completed, do not apply force horizontally or vertically from behind panel. • Behind the panel, cut area should be squared. If front of panel is painted, do not allow any paint to collect in corners of cutout to prevent level mounting. Supplement • Avoid reinstalling a switch once it has been mounted into panel. This may cause deterioration of panel sealability. E20 www.nkkswitches.com Clean Edges