74LVC2G17GV

74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input Rev. 04 — 9 October 2006 Product data sheet 1. General description The 74LVC2G17 is a high-performance, low-power, low-voltage, Si-gate CMOS device and superior to most advanced CMOS compatible TTL families. Inputs can be driven from either 3.3 V or 5 V devices. This feature allows the use of these devices as translators in a mixed 3.3 V and 5 V environment. This device is fully specified for partial power-down applications using IOFF. The IOFF circuitry disables the output, preventing the damaging backflow current through the device when it is powered down. The 74LVC2G17 provides two non-inverting buffers with Schmitt trigger action. It is capable of transforming slowly changing input signals into sharply defined, jitter-free output signals. 2. Features I I I I Wide supply voltage range from 1.65 V to 5.5 V 5 V tolerant input/output for interfacing with 5 V logic High noise immunity Complies with JEDEC standard: N JESD8-7 (1.65 V to 1.95 V) N JESD8-5 (2.3 V to 2.7 V) N JESD-8B/JESD36 (2.7 V to 3.6 V) ESD protection: N HBM JESD22-A114-D exceeds 2000 V N MM JESD22-A115-A exceeds 200 V ±24 mA output drive (VCC = 3.0 V) CMOS low-power consumption Latch-up performance exceeds 250 mA Direct interface with TTL levels Multiple package options Specified from −40 °C to +85 °C and −40 °C to +125 °C I I I I I I I 3. Applications I Wave and pulse shapers for highly noisy environments NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input 4. Ordering information Table 1. Ordering information Package Temperature range 74LVC2G17GW 74LVC2G17GV 74LVC2G17GM 74LVC2G17GF −40 °C to +125 °C −40 °C to +125 °C −40 °C to +125 °C −40 °C to +125 °C Name SC-88 SC-74 XSON6 XSON6 Description plastic surface-mounted package; 6 leads plastic extremely thin small outline package; no leads; 6 terminals; body 1 × 1.45 × 0.5 mm plastic extremely thin small outline package; no leads; 6 terminals; body 1 × 1 × 0.5 mm Version SOT363 SOT886 SOT891 Type number plastic surface-mounted package (TSOP6); 6 leads SOT457 5. Marking Table 2. Marking codes Marking code VV VV VV VV Type number 74LVC2G17GW 74LVC2G17GV 74LVC2G17GM 74LVC2G17GF 6. Functional diagram 1 1A 1Y 6 1 6 3 2A 2Y 4 3 4 mnb066 mnb067 Fig 1. Logic symbol Fig 2. IEC logic symbol 1A 1Y 2A 2Y mnb068 Fig 3. Logic diagram 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 2 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input 7. Pinning information 7.1 Pinning 74LVC2G17 74LVC2G17 1A GND 1 2 6 5 1Y GND VCC 2A 2A 3 001aaf078 1A 1 6 1Y 1A GND 74LVC2G17 1 2 3 6 5 4 1Y VCC 2Y 2 5 VCC 3 4 2Y 2A 4 2Y 001aaf079 001aaf080 Transparent top view Transparent top view Fig 4. Pin configuration SOT363 and SOT457 Fig 5. Pin configuration SOT886 Fig 6. Pin configuration SOT891 7.2 Pin description Table 3. Symbol 1A GND 2A 2Y VCC 1Y Pin description Pin 1 2 3 4 5 6 Description data input ground (0 V) data input data output supply voltage data input 8. Functional description Table 4. Input nA L H [1] H = HIGH voltage level; L = LOW voltage level. Function table[1] Output nY L H 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 3 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input 9. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol VCC IIK VI IOK VO IO ICC IGND Tstg Ptot [1] [2] [3] Parameter supply voltage input clamping current input voltage output clamping current output voltage output current supply current ground current storage temperature total power dissipation Conditions VI < 0 V [1] Min −0.5 −0.5 [1][2] [1][2] Max +6.5 −50 +6.5 −50 VCC + 0.5 +6.5 ±50 100 −100 +150 300 Unit V mA V mA V V mA mA mA °C mW VO < 0 V Active mode Power-down mode VO = 0 V to VCC −0.5 −0.5 −65 Tamb = −40 °C to +125 °C [3] - The input and output voltage ratings may be exceeded if the input and output current ratings are observed. When VCC = 0 V (Power-down mode), the output voltage can be 5.5 V in normal operation. For SC-88 and SC-74 packages: above 87.5 °C the value of Ptot derates linearly with 4.0 mW/K. For XSON6 packages: above 45 °C the value of Ptot derates linearly with 2.4 mW/K. 10. Recommended operating conditions Table 6. Symbol VCC VI VO Tamb Recommended operating conditions Parameter supply voltage input voltage output voltage ambient temperature Conditions Min 1.65 0 0 −40 Typ Max 5.5 5.5 VCC +125 Unit V V V °C 11. Static characteristics Table 7. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Tamb = −40 °C to +85 VOL °C[1] VI = VIH or VIL IO = 100 µA; VCC = 1.65 V to 5.5 V IO = 4 mA; VCC = 1.65 V IO = 8 mA; VCC = 2.3 V IO = 12 mA; VCC = 2.7 V IO = 24 mA; VCC = 3.0 V IO = 32 mA; VCC = 4.5 V 0.1 0.45 0.3 0.4 0.55 0.55 V V V V V V LOW-level output voltage Conditions Min Typ Max Unit 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 4 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter VOH HIGH-level output voltage Conditions VI = VIH or VIL IO = −100 µA; VCC = 1.65 V to 5.5 V IO = −4 mA; VCC = 1.65 V IO = −8 mA; VCC = 2.3 V IO = −12 mA; VCC = 2.7 V IO = −24 mA; VCC = 3.0 V IO = −32 mA; VCC = 4.5 V II IOFF ICC ∆ICC CI VOL input leakage current power-off leakage current supply current additional supply current input capacitance LOW-level output voltage VI = VIH or VIL IO = 100 µA; VCC = 1.65 V to 5.5 V IO = 4 mA; VCC = 1.65 V IO = 8 mA; VCC = 2.3 V IO = 12 mA; VCC = 2.7 V IO = 24 mA; VCC = 3.0 V IO = 32 mA; VCC = 4.5 V VOH HIGH-level output voltage VI = VIH or VIL IO = −100 µA; VCC = 1.65 V to 5.5 V IO = −4 mA; VCC = 1.65 V IO = −8 mA; VCC = 2.3 V IO = −12 mA; VCC = 2.7 V IO = −24 mA; VCC = 3.0 V IO = −32 mA; VCC = 4.5 V II IOFF ICC ∆ICC input leakage current power-off leakage current supply current additional supply current VI = 5.5 V or GND; VCC = 5.5 V VI or VO = 5.5 V; VCC = 0 V VI = VCC or GND; IO = 0 A; VCC = 5.5 V VI = VCC − 0.6 V; IO = 0 A; VCC = 2.3 V to 5.5 V VCC − 0.1 0.95 1.7 1.9 2.0 3.4 ±0.1 ±20 ±20 40 5 V V V V V V µA µA µA mA 0.1 0.70 0.45 0.60 0.80 0.80 V V V V V V VI = 5.5 V or GND; VCC = 5.5 V VI or VO = 5.5 V; VCC = 0 V VI = VCC or GND; IO = 0 A; VCC = 5.5 V VI = VCC − 0.6 V; IO = 0 A; VCC = 2.3 V to 5.5 V VCC − 0.1 1.2 1.9 2.2 2.3 3.8 ±0.1 ±0.1 0.1 5 3.5 ±5 ±10 10 500 V V V V V V µA µA µA µA pF Min Typ Max Unit Tamb = −40 °C to +125 °C [1] All typical values are measured at VCC = 3.3 V and Tamb = 25 °C. 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 5 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input 12. Dynamic characteristics Table 8. Dynamic characteristics Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8. Symbol Parameter tpd Conditions Min propagation delay nA to nY; see Figure 7 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V CPD power dissipation capacitance per buffer; VCC = 3.3 V; VI = GND to VCC [3] [2] −40 °C to +85 °C Typ[1] 5.6 3.7 3.8 3.6 2.7 16.3 Max 10.5 6.5 6.5 5.7 4.3 - −40 °C to +125 °C Min 1.5 1.0 1.0 1.0 1.0 Max 13.1 8.5 8.5 7.1 5.4 - Unit 1.5 1.0 1.0 1.0 1.0 - ns ns ns ns ns pF [1] [2] [3] Typical values are measured at Tamb = 25 °C and VCC = 1.8 V, 2.5 V, 2.7 V, 3.3 V and 5.0 V respectively. tpd is the same as tPLH and tPHL. CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi × N + ∑(CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in V; N = number of inputs switching; ∑(CL × VCC2 × fo) = sum of outputs. 13. Waveforms VI nA input GND tPLH VOH nY output VOL mnb072 VM VM tPHL VM VM Measurement points are given in Table 9. VOL and VOH are typical output voltage drop that occur with the output load. Fig 7. The input (nA) to output (nY) propagation delays and the output transition times 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 6 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input Table 9. VCC Measurement points Input VM 0.5 × VCC 0.5 × VCC 1.5 V 1.5 V 0.5 × VCC Output VM 0.5 × VCC 0.5 × VCC 1.5 V 1.5 V 0.5 × VCC Supply voltage 1.65 V to 1.95 V 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V VEXT VCC PULSE GENERATOR VI DUT RT CL RL RL VO mna616 Measurement points are given in Table 10. Definitions for test circuit: RL = Load resistance. CL = Load capacitance including jig and probe capacitance. RT = Termination resistance should be equal to output impedance Zo of the pulse generator. VEXT = External voltage for measuring switching times. Fig 8. Load circuitry for switching times Table 10. VCC 1.65 V to 1.95 V 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V Test data Input VI VCC VCC 2.7 V 2.7 V VCC tr, tf ≤ 2.0 ns ≤ 2.0 ns ≤ 2.5 ns ≤ 2.5 ns ≤ 2.5 ns Load CL 30 pF 30 pF 50 pF 50 pF 50 pF RL 1 kΩ 500 Ω 500 Ω 500 Ω 500 Ω VEXT tPLH, tPHL open open open open open Supply voltage 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 7 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input 14. Transfer characteristics Table 11. Transfer characteristics At recommended operating conditions. Voltages are referenced to GND (ground = 0 V). Symbol Parameter VT+ positive-going threshold voltage Conditions see Figure 9 and Figure 10 VCC = 1.8 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V VCC = 5.5 V VT− negative-going threshold voltage see Figure 9 and Figure 10 VCC = 1.8 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V VCC = 5.5 V VH hysteresis voltage (VT+ − VT−); see Figure 9, Figure 10 and Figure 11 VCC = 1.8 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V VCC = 5.5 V [1] All typical values are measured at Tamb = 25 °C. −40 °C to +85 °C Min 0.70 1.00 1.30 1.90 2.20 0.25 0.40 0.60 1.00 1.20 Typ[1] 1.10 1.40 1.76 2.47 2.91 0.61 0.80 1.04 1.55 1.86 Max 1.50 1.80 2.20 3.10 3.60 0.90 1.15 1.50 2.00 2.30 −40 °C to +125 °C Unit Min 0.70 1.00 1.30 1.90 2.20 0.25 0.40 0.60 1.00 1.20 Max 1.70 2.00 2.40 3.30 3.80 1.10 1.35 1.70 2.20 2.50 V V V V V V V V V V 0.15 0.25 0.40 0.60 0.70 0.49 0.60 0.73 0.92 1.02 1.00 1.10 1.20 1.50 1.70 0.15 0.25 0.40 0.60 0.70 1.20 1.30 1.40 1.70 1.90 V V V V V 15. Waveforms transfer characteristics VO VI VT+ VT− VH VO VI VT+ mnb154 VH VT− mnb155 VT+ and VT− limits at 70 % and 20 %. Fig 9. Transfer characteristic Fig 10. Definition of VT+, VT− and VH 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 8 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input 14 ICC (mA) 12 10 8 6 4 2 0 0 0.5 1 1.5 mnb071 2 VI (V) VCC = 3.0 V. Fig 11. Typical transfer characteristic 50 ICC (mA) (1) mnb156 40 30 20 (2) 10 0 2 3 4 5 VCC (V) 6 (1) Positive-going edge (2) Negative-going edge Linear change of VI between 0.8 V to 2.0 V. All values given are typical unless otherwise specified. Fig 12. Average ICC as a function of VCC 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 9 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input 16. Package outline Plastic surface-mounted package; 6 leads SOT363 D B E A X y HE vMA 6 5 4 Q pin 1 index A A1 1 e1 e 2 bp 3 wM B detail X Lp c 0 1 scale 2 mm DIMENSIONS (mm are the original dimensions) UNIT mm A 1.1 0.8 A1 max 0.1 bp 0.30 0.20 c 0.25 0.10 D 2.2 1.8 E 1.35 1.15 e 1.3 e1 0.65 HE 2.2 2.0 Lp 0.45 0.15 Q 0.25 0.15 v 0.2 w 0.2 y 0.1 OUTLINE VERSION SOT363 REFERENCES IEC JEDEC JEITA SC-88 EUROPEAN PROJECTION ISSUE DATE 04-11-08 06-03-16 Fig 13. Package outline SOT363 (SC-88) 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 10 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input Plastic surface-mounted package (TSOP6); 6 leads SOT457 D B E A X y HE vMA 6 5 4 Q pin 1 index A A1 c 1 2 3 Lp e bp wM B detail X 0 1 scale 2 mm DIMENSIONS (mm are the original dimensions) UNIT mm A 1.1 0.9 A1 0.1 0.013 bp 0.40 0.25 c 0.26 0.10 D 3.1 2.7 E 1.7 1.3 e 0.95 HE 3.0 2.5 Lp 0.6 0.2 Q 0.33 0.23 v 0.2 w 0.2 y 0.1 OUTLINE VERSION SOT457 REFERENCES IEC JEDEC JEITA SC-74 EUROPEAN PROJECTION ISSUE DATE 05-11-07 06-03-16 Fig 14. Package outline SOT457 (SC-74) 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 11 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm SOT886 b 1 2 3 4× L1 L (2) e 6 e1 5 e1 4 6× (2) A A1 D E terminal 1 index area 0 DIMENSIONS (mm are the original dimensions) UNIT mm A (1) max 0.5 A1 max 0.04 b 0.25 0.17 D 1.5 1.4 E 1.05 0.95 e 0.6 e1 0.5 L 0.35 0.27 L1 0.40 0.32 1 scale 2 mm Notes 1. Including plating thickness. 2. Can be visible in some manufacturing processes. OUTLINE VERSION SOT886 REFERENCES IEC JEDEC MO-252 JEITA EUROPEAN PROJECTION ISSUE DATE 04-07-15 04-07-22 Fig 15. Package outline SOT886 (XSON6) 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 12 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1 x 0.5 mm SOT891 1 2 b 3 L1 e L 6 e1 5 e1 4 A A1 D E terminal 1 index area 0 1 scale 2 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max 0.5 A1 max 0.04 b 0.20 0.12 D 1.05 0.95 E 1.05 0.95 e 0.55 e1 0.35 L 0.35 0.27 L1 0.40 0.32 OUTLINE VERSION SOT891 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 05-03-11 05-04-06 Fig 16. Package outline SOT891 (XSON6) 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 13 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input 17. Abbreviations Table 12. Acronym CMOS DUT ESD HBM MM TTL Abbreviations Description Complementary Metal Oxide Semiconductor Device Under Test ElectroStatic Discharge Human Body Model Machine Model Transistor-Transistor Logic 18. Revision history Table 13. Revision history Release date 20061009 Data sheet status Product data sheet Change notice Supersedes 74LVC2G17_3 Document ID 74LVC2G17_4 Modifications: • • • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. Legal texts have been adapted to the new company name where appropriate. Added type number 74LVC2G17GF (SOT891 package). Product data sheet Product specification Product specification 74LVC2G17_2 74LVC2G17_1 - 74LVC2G17_3 74LVC2G17_2 74LVC2G17_1 20050926 20040908 20030813 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 14 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input 19. Legal information 19.1 Data sheet status Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet [1] [2] [3] Product status[3] Development Qualification Production Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification. Please consult the most recently issued document before initiating or completing a design. The term ‘short data sheet’ is explained in section “Definitions”. The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 19.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 19.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or 19.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 20. Contact information For additional information, please visit: http://www.nxp.com For sales office addresses, send an email to: salesaddresses@nxp.com 74LVC2G17_4 © NXP B.V. 2006. All rights reserved. Product data sheet Rev. 04 — 9 October 2006 15 of 16 NXP Semiconductors 74LVC2G17 Dual non-inverting Schmitt trigger with 5 V tolerant input 21. Contents 1 2 3 4 5 6 7 7.1 7.2 8 9 10 11 12 13 14 15 16 17 18 19 19.1 19.2 19.3 19.4 20 21 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 4 Dynamic characteristics . . . . . . . . . . . . . . . . . . 6 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Transfer characteristics. . . . . . . . . . . . . . . . . . . 8 Waveforms transfer characteristics . . . . . . . . . 8 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 10 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 14 Legal information. . . . . . . . . . . . . . . . . . . . . . . 15 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 15 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Contact information. . . . . . . . . . . . . . . . . . . . . 15 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2006. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 9 October 2006 Document identifier: 74LVC2G17_4