CM50TF-12H

CM50TF-12H Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Six-IGBT IGBTMOD™ H-Series Module 50 Amperes/600 Volts A B C BuP EuP BvP EvP BwP EwP P J N u v w E N D BuN EuN BvN EvN BwN EwN S - DIA. (2 TYP.) M R F R L .250 TAB F R L K Q .110 TAB G P H R P (BuP)* GuP EuP u (BvP) GvP EvP v (BwP) GwP EwP w Description: Powerex IGBTMOD™ Modules are designed for use in switching applications. Each module consists of six IGBT Transistors in a three phase bridge configuration, with each transistor having a reverseconnected super-fast recovery free-wheel diode. All components and interconnects are isolated from the heat sinking baseplate, offering simplified system assembly and thermal management. Features: □ Low Drive Power □ Low VCE(sat) □ Discrete Super-Fast Recovery (70ns) Free-Wheel Diode □ High Frequency Operation (20-25kHz) □ Isolated Baseplate for Easy Heat Sinking Applications: □ AC Motor Control □ Motion/Servo Control □ UPS □ Welding Power Supplies □ Laser Power Supplies Ordering Information: Example: Select the complete part module number you desire from the table below -i.e. CM50TF-12H is a 600V (VCES), 50 Ampere SixIGBT IGBTMOD™ Power Module. Type CM Current Rating Amperes 50 VCES Volts (x 50) 12 (BuN) GuN EuN N (BvN) GvN EvN (BwN) GwN EwN * Parentheses indicate module marking Outline Drawing and Circuit Diagram Dimensions A B C D E F G H J Inches 5.00 4.33± 0.01 3.86 2.20 1.57 1.12 1.04 1.01 0.98 Millimeters 127.0 110.0± 0.3 98.0 56.0 40.0 28.5 26.5 25.6 25.0 Dimensions K L M N P Q R S Inches 0.85 0.83 0.75 0.71 0.69 0.65 0.30 0.22 Dia. Millimeters 21.5 21.0 19.0 18.0 17.5 16.5 7.5 Dia. 5.5 307 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CM50TF-12H Six-IGBT IGBTMOD™ H-Series Module 50 Amperes/600 Volts Absolute Maximum Ratings, Tj = 25 °C unless otherwise specified Ratings Junction Temperature Storage Temperature Collector-Emitter Voltage (G-E SHORT) Gate-Emitter Voltage Collector Current Peak Collector Current Diode Forward Current Diode Forward Surge Current Power Dissipation Max. Mounting Torque M5 Mounting Screws Module Weight (Typical) V Isolation * Pulse width and repetition rate should be such that device junction temperature does not exceed the device rating. Symbol Tj Tstg VCES VGES IC ICM IF IFM Pd – – VRMS CM50TF-12H –40 to 150 –40 to 125 600 ± 20 50 100* 50 100* 250 17 390 2500 Units °C °C Volts Volts Amperes Amperes Amperes Amperes Watts in-lb Grams Volts Static Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Collector-Cutoff Current Gate Leakage Current Gate-Emitter Threshold Voltage Collector-Emitter Saturation Voltage Symbol ICES IGES VGE(th) VCE(sat) QG VFM Test Conditions VCE = VCES, VGE = 0V VGE = VGES, VCE = 0V IC = 5mA, VCE = 10V IC = 50A, VGE = 15V IC = 50A, VGE = 15V, Tj = 150°C Total Gate Charge Diode Forward Voltage VCC = 300V, IC = 50A, VGS = 15V IE = 50A, VGS = 0V Min. – – 4.5 – – – – Typ. – – 6.0 2.1 2.15 150 – Max. 1.0 0.5 7.5 2.8** – – 2.8 Units mA µA Volts Volts Volts nC Volts ** Pulse width and repetition rate should be such that device junction temperature rise is negligible. Dynamic Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Input Capacitance Output Capacitance Reverse Transfer Capacitance Resistive Load Switching Times Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time Symbol Cies Coes Cres td(on) tr td(off) tf trr Qrr IE = 50A, diE/dt = –100A/µs IE = 50A, diE/dt = –100A/µs VCC = 300V, IC = 50A, VGE1 = VGE2 = 15V, RG = 13Ω VGE = 0V, VCE = 10V, f = 1MHz Test Conditions Min. – – – – – – – – – Typ. – – – – – – – – 0.14 Max. 5 1.8 1 200 300 200 300 110 – Units nF nF nF ns ns ns ns ns Diode Reverse Recovery Time Diode Reverse Recovery Charge µC Thermal and Mechanical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Thermal Resistance, Junction to Case Thermal Resistance, Junction to Case Contact Thermal Resistance Symbol Rth(j-c) Rth(j-c) Rth(c-f) Test Conditions Per IGBT Per FWDi Per Module, Thermal Grease Applied Min. – – – Typ. – – – Max. 0.50 1.00 0.042 Units °C/W °C/W °C/W 308 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CM50TF-12H Six-IGBT IGBTMOD™ H-Series Module 50 Amperes/600 Volts OUTPUT CHARACTERISTICS (TYPICAL) TRANSFER CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) 100 Tj = 25oC COLLECTOR CURRENT, IC, (AMPERES) COLLECTOR CURRENT, IC, (AMPERES) 100 COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 5 VCE = 10V Tj = 25°C Tj = 125°C VGE = 15V Tj = 25°C Tj = 125°C VGE = 20V 15 12 75 11 75 4 3 50 10 50 2 25 7 9 8 25 1 0 0 2 4 6 8 10 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) 0 0 4 8 12 16 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) 0 0 25 50 75 100 COLLECTOR-CURRENT, IC, (AMPERES) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) CAPACITANCE VS. VCE (TYPICAL) 10 COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 102 Tj = 25°C EMITTER CURRENT, IE, (AMPERES) 101 Tj = 25°C CAPACITANCE, Cies, Coes, Cres, (nF) 8 Cies IC = 100A 6 IC = 50A 101 100 Coes 4 2 IC = 20A VGE = 0V f = 1MHz Cres 0 0 4 8 12 16 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) 100 0 0.8 1.6 2.4 3.2 4.0 EMITTER-COLLECTOR VOLTAGE, VEC, (VOLTS) 10-1 10-1 100 101 102 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) HALF-BRIDGE SWITCHING CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CURRENT, Irr, (AMPERES) GATE CHARGE, VGE 103 REVERSE RECOVERY TIME, t rr, (ns) 103 tf 101 20 GATE-EMITTER VOLTAGE, VGE, (VOLTS) 16 SWITCHING TIME, (ns) td(off) Irr VCC = 200V 12 102 td(on) 102 t rr 100 VCC = 300V 8 tr VCC = 300V VGE = ±15V RG = 13Ω Tj = 125°C di/dt = -100A/µsec Tj = 25°C 4 101 100 101 COLLECTOR CURRENT, IC, (AMPERES) 102 101 100 101 EMITTER CURRENT, IE, (AMPERES) 10-1 102 0 0 50 100 150 200 250 GATE CHARGE, QG, (nC) 309 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CM50TF-12H Six-IGBT IGBTMOD™ H-Series Module 50 Amperes/600 Volts NORMALIZED TRANSIENT THERMAL IMPEDANCE, Z th(j-c) Zth = Rth • (NORMALIZED VALUE) NORMALIZED TRANSIENT THERMAL IMPEDANCE, Z th(j-c) Zth = Rth • (NORMALIZED VALUE) 10-3 101 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) 10-2 10-1 100 101 10-3 101 TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) 10-2 10-1 100 101 100 Single Pulse TC = 25°C Per Unit Base = R th(j-c) = 0.5°C/W 100 Single Pulse TC = 25°C Per Unit Base = R th(j-c) = 1.0°C/W 10-1 10-1 10-1 10-1 10-2 10-2 10-2 10-2 10-3 10-5 TIME, (s) 10-4 10-3 10-3 10-3 10-5 TIME, (s) 10-4 10-3 10-3 310