2SP0325T2A1-CM2500DY-24S 数据手册
2SP0325x2Ax-CM2500DY-24S
2SP0325x2Ax-CM2500DY-24S
Preliminary Data Sheet
Compact, high-performance, plug-and-play dual-channel IGBT driver based on
SCALE™-2 technology for Mitsubishi’s New Mega Power Dual IGBT modules.
Abstract
The SCALE™-2 plug-and-play driver 2SP0325x2Ax-CM2500DY-24S is a compact dual-channel intelligent gate
driver designed for Mitsubishi’s New Mega Power Dual (New MPD) IGBT modules CM2500DY-24S 300G and
CM2500DY-24S 302G. The driver features an electrical interface (2SP0325T) or a fiber-optic interface
(2SP0325V) with a built-in DC/DC power supply.
For drivers adapted to other types of high-power and high-voltage IGBT modules, refer to
www.IGBT-Driver.com/go/plug-and-play
Features
Applications
> Plug-and-play solution
> For 2-level, 3-level and multilevel topologies
> Built-in DC/DC power supply
> 20-pin flat cable interface (2SP0325T)
> Fiber-optic links (2SP0325V)
> Duty cycle 0... 100%
> Dynamic Advanced Active Clamping DA C
> IGBT short-circuit protection
> Monitoring of supply voltage
> Safe isolation to EN 50178
> UL compliant
> Lead free
> Extremely reliable; long service life
> Shortens application development time
> Suitable for CM2500DY-24S 300G
> Wind power converters
> AC motor control
> Power supply
> Medium voltage drives
> And many others
2
and CM2500DY-24S 302G
www.IGBT-Driver.com
Page 1
2SP0325x2Ax-CM2500DY-24S
Preliminary Data Sheet
Safety Notice!
The data contained in this data sheet is intended exclusively for technically trained staff. Handling all highvoltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory!
Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive
devices according to international standard IEC 60747-1, Chapter IX or European standard EN 100015 (i.e. the
workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged.
Important Product Documentation
This data sheet contains only product-specific data. For a detailed description, must-read application notes and
common data that apply to the whole series, please refer to “Description & Application Manual for 2SP0325T
SCALE-2 IGBT Drivers” (electrical interface) or “Description & Application Manual for 2SP0325V SCALE-2 IGBT
Drivers” (fiber-optic interface) on www.IGBT-Driver.com/go/2SP0325.
When applying SCALE-2 plug-and-play drivers, please note that these drivers are specifically adapted to a
particular type of IGBT module. Therefore, the type designation of SCALE-2 plug-and-play drivers also includes
the type designation of the corresponding IGBT module. These drivers are not valid for IGBT modules other
than those specified. Incorrect use may result in failure.
Mechanical Dimensions
Dimensions: See the relevant “Description and Application Manual”
Mounting principle: Connected to IGBT module with screws
Fiber-Optic Interfaces
Interface
Remarks
Drive signal input
Status output
2SP0325V, fiber-optic receiver (Notes 21, 22)
2SP0325V, fiber-optic transmitter (Notes 21, 23)
www.IGBT-Driver.com
Part type #
HFBR-2522ETZ
HFBR-1522ETZ
Page 2
2SP0325x2Ax-CM2500DY-24S
Preliminary Data Sheet
Absolute Maximum Ratings
Parameter
Remarks
Min
Supply voltage V DC
Supply voltage V CC
Logic input and output voltages
SO x current
Gate peak current I out
Average supply current I DC
Average supply current I DC
Output power per gate
Switching frequency F
Test voltage (50Hz/1min.)
VDC to GND (Note 1)
VCC to GND (Note 1)
To GND
Fault condition, total current
Note 2
2SP0325T (Note 24)
2SP0325V (Note 24)
Note 3
0
16
V
0
16
V
-0.5 VCC+0.5 V
20
mA
-25
+25
A
430
mA
550
mA
2
W
5
kHz
3800 V AC(eff)
DC-link voltage
|dv/dt|
Operating voltage
Operating temperature
Storage temperature
Primary to secondary (Note 19)
Secondary to secondary (Note 19)
Switching operation (Note 4)
Off state (Note 29)
Rate of change of input to output voltage (Note 20)
Primary/secondary, secondary/secondary
Max
Unit
-40
-40
3800 V AC(eff)
800
V
990
V
50 N9NjV
1200 V peak
+85
°C
+90
°C
Recommended Operating Conditions
Power Supply
Remarks
Min
Typ
Max
Unit
Supply voltage V DC
Supply voltage V CC
Resistance from TB to GND
To GND (Note 1)
To GND (Note 1)
2SP0325T, blocking time0, ext. value
14.5
14.5
128
15
15
15.5
15.5
V
V
Nƻ
www.IGBT-Driver.com
Page 3
2SP0325x2Ax-CM2500DY-24S
Preliminary Data Sheet
Electrical Characteristics
All data refer to +25°C and V CC = V DC = 15V unless otherwise specified
Power Supply
Remarks
Supply current I DC
2SP0325T, without load
2SP0325V, without load
Internal DC/DC converter
Without load
Primary side to secondary side, total, per channel
2SP0325T
2SP0325V
32
145
85
23
mA
mA
%
mA
22
12
pF
pF
Power Supply Monitoring
Remarks
Min
Typ
Max
Unit
Supply threshold V CC
11.9
11.3
0.35
12.1
11.5
0.35
5
4.7
0.15
12.6
12.0
13.3
12.7
12.6
12.0
13.1
12.5
5.15
4.85
5.3
5
Monitoring hysteresis
Primary side, clear fault
Primary side, set fault (Note 5)
Primary side, set/clear fault
Secondary side, clear fault
Secondary side, set fault (Note 26)
Secondary side, set/clear fault
Secondary side, clear fault
Secondary side, set fault (Note 26)
Secondary side, set/clear fault
V
V
V
V
V
V
V
V
V
Logic Inputs and Outputs
Remarks
Min
Typ
Max
Unit
Input impedance
Turn-on threshold
Turn-off threshold
SOx output voltage
2SP0325T, V(INx) = 15V (Note 6)
2SP0325T, V(INx) (Note 7)
2SP0325T, V(INx) (Note 7)
Fault condition, I(SOx) 600V (Note 8)
After the response time (Note 9)
2SP0325T, after fault (Note 10)
Efficiency dž
Supply current I CC
Coupling capacitance C io
Monitoring hysteresis
Supply threshold V isox -V eex
Monitoring hysteresis
Supply threshold V eex -V COMx
Delay in IGBT turn-off T cshd
Blocking time
www.IGBT-Driver.com
Min
Typ
Typ
Max
Unit
10.2
V
7.2
0.1
90
NjV
NjV
ms
Page 4
2SP0325x2Ax-CM2500DY-24S
Preliminary Data Sheet
Timing Characteristics
Remarks
Min
Turn-on delay T d(on)
Turn-off delay T d(off)
Jitter of turn-on delay
Jitter of turn-off delay
Turn-on delay T d(on)
Turn-off delay T d(off)
2SP0325T
2SP0325T
2SP0325T
2SP0325T
2SP0325V
2SP0325V
Output rise time T r(out)
Output fall time T f(out)
G x to E x (Note 13)
G x to E x (Note 13)
Dead time between outputs
Jitter of dead time
2SP0325T, half-bridge mode (Note 30)
2SP0325T, half-bridge mode
Transmission delay of fault state
Transmission delay of fault state
Delay to clear fault state
(Note
(Note
(Note
(Note
(Note
(Note
11)
11)
28)
28)
12)
12)
Typ
Max
Unit
80
65
±2
±2
120
100
ns
ns
ns
ns
ns
ns
25
17
ns
ns
3
±100
NjV
ns
2SP0325T (Note 14)
2SP0325V (Note 25)
2SP0325V (Note 15)
450
90
8
ns
ns
NjV
Acknowledge delay time T d(ack)
Acknowledge pulse width T (ack,on)
Acknowledge pulse width T (ack,off)
2SP0325V (Note 16)
2SP0325V (at turn-on, on host side)
2SP0325V (at turn-off, on host side)
400
400
200
600
750
1050
1150
ns
ns
ns
Outputs
Remarks
Min
Typ
Max
Unit
Turn-on gate resistor R g(on)
Turn-off gate resistor R g(off)
Gate voltage at turn-on
Gate-voltage at turn-off
Note 17
Note 17
2SP0325T/2SP0325V
F = 0kHz
F = 5kHz
Gate resistance to COMx
0.5
2
15
ƻ
ƻ
V
-10.2/-9.9
-9.7/-9.3
4.7
V
V
Nƻ
dv/dt Feedback
Remarks
dv/dt feedback
Note 18
Electrical Isolation
Remarks
Test voltage (50Hz/1s)
Primary to secondary side (Note 19)
3800
3850
3900
V eff
Secondary to secondary side (Note 19)
3800
3850
3900
V eff
Partial discharge extinction volt.
Creepage distance
Clearance distance
www.IGBT-Driver.com
Implementation
Yes
Min
Typ
Max
Unit
Primary to secondary side (Note 27)
1220
V peak
Secondary to secondary side (Note 27)
1200
V peak
Primary to secondary side
12.5
mm
Secondary to secondary side
6.5
mm
Primary to secondary side
12.5
mm
Secondary to secondary side
6.5
mm
Page 5
2SP0325x2Ax-CM2500DY-24S
Preliminary Data Sheet
Footnotes to the Key Data
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
19)
20)
Both supply voltages V DC and V CC should be applied in parallel.
The gate current is limited by the gate resistors located on the driver and the internal gate resistance
of the IGBT module.
If the specified value is exceeded, this indicates a driver overload. It should be noted that the driver is
not protected against overload.
This limit is due to active clamping. Refer to “Description & Application Manual for 2SP0325T SCALE-2
IGBT Drivers” (electrical interface) or “Description & Application Manual for 2SP0325V SCALE-2 IGBT
Drivers” (fiber-optic interface).
Undervoltage monitoring of the primary-side supply voltage (VCC to GND). If the voltage drops below
this limit, a fault is transmitted to the corresponding output(s) (2SP0325T and 2SP0325V) and the
IGBTs are switched off (only 2SP0325T).
The input impedance can be modified (customer-specific solution).
Turn-on and turn-off threshold values can be modified (customer-specific solution).
The pulse width resulting from the direct output of the gate drive unit for half-bridge short circuits
(excluding the delay of the gate resistors) is the sum of the response time plus the delay to IGBT
turn-off. The short-circuit time may vary depending on the exact short-circuit conditions. Note that
Mitsubishi’s short-circuit SOA CMH-10030 does not allow short-circuit inductances smaller than 10uH
for external short circuits with CM2500DY-24S 300G, and that Mitsubishi’s short-circuit SOA
CMH-10031 does not allow short-circuit inductances smaller than 5uH for external short circuits with
CM2500DY-24S 302G.
The turn-off event of the IGBT is delayed by the specified time after the response time.
Factory set value. The blocking time can be reduced with an external resistor. Refer to “Description &
Application Manual for 2SP0325T SCALE-2 IGBT Drivers”.
Measured from the transition of the turn-on or turn-off command at the driver input to direct output
of the gate drive unit (excluding the delay of the gate resistors).
Including the delay of the external fiber-optic links. Measured from the transition of the turn-on or
turn-off command at the optical transmitter on the host controller side to the direct output of the gate
drive unit (excluding the delay of the gate resistors).
Output rise and fall times are measured between 10% and 90% of the nominal output swing with an
RXWSXWORDGRIƻULVHWLPHƻIDOOWLPHDQGQ)7KHYDOXHVDUHJLYHQIRUWKHGULYHUVLGHRIWKH
gate resistors.
Transmission delay of the fault state from the secondary side to the primary status outputs.
Measured on the host side. The fault status on the secondary side is automatically reset after the
specified time.
Including the delay of the external fiber-optic links. Measured from the transition of the turn-on or
turn-off command at the optical transmitter on the host controller side to the transition of the
acknowledge signal at the optical receiver on the host controller side.
The gate resistors can be leaded or surface mounted. CONCEPT reserves the right to determine which
type will be used. Typically, higher quantities will be produced with SMD resistors and small quantities
with leaded resistors.
With “Yes”, a dv/dt feedback reduces the rate of rise of the collector-emitter voltage of the IGBTs at
turn-off. For more information, refer to the “Description & Application Manual for 2SP0325T SCALE-2
IGBT Drivers” (electrical interface), or the “Description & Application Manual for 2SP0325V SCALE-2
IGBT Drivers” (fiber-optic interface). With “No”, no dv/dt feedback is implemented.
HiPot testing (= dielectric testing) must generally be restricted to suitable components. This gate
driver is suited for HiPot testing. Nevertheless, it is strongly recommended to limit the testing time to
1s slots as stipulated by EN 50178. Excessive HiPot testing at voltages much higher than 850V AC(eff)
may lead to insulation degradation. No degradation has been observed over 1min. testing at
3800V AC(eff) . Every production sample shipped to customers has undergone 100% testing at the given
value or higher (