STP130N10F3

STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 N-channel 100 V, 7.8 mΩ typ., 120 A STripFET™III Power MOSFET in TO-220FP, I²PAKFP, H²PAK-2 and TO-220 packages Datasheet — production data Features Order codes VDSS STH130N10F3-2 ID 9.6 mΩ 46 A 3 STF130N10F3 STFI130N10F3 RDS(on) max. 100 V STP130N10F3 ■ Ultra low on-resistance ■ 100% avalanche tested 1 2 1 TO-220FP 2 3 I²PAKFP 9.3 mΩ 120 A 9.6 mΩ TAB TAB 2 3 3 1 1 2 TO-220 H²PAK-2 Applications ■ High current switching applications Figure 1. Description Internal schematic diagram $4!" These devices are N-channel enhancement mode Power MOSFETs produced using STMicroelectronics’ STripFET™ III technology, which is specifically designed to minimize onresistance and gate charge to provide superior switching performance. $4!" ' ' 3 4/ 4/ &0AND) 0!+&0 3 (£0!+  !-V Table 1. Device summary Order codes Marking Package Packaging TO-220FP Tube I²PAKFP Tube STH130N10F3-2 H²PAK-2 Tape and reel STP130N10F3 TO-220 Tube STF130N10F3 STFI130N10F3 130N10F3 November 2012 This is information on a product in full production. Doc ID 018492 Rev 3 1/23 www.st.com 23 Contents STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) ........................... 6 3 Test circuits 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 2/23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Doc ID 018492 Rev 3 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter TO-220FP I²PAKFP Unit H²PAK-2 TO-220 VDS Drain-source voltage 100 V VGS Gate-source voltage ± 20 V ID (1) Drain current (continuous) at TC = 25°C 46 120 A ID (1) Drain current (continuous) at TC=100°C 29 78 A IDM (2) Drain current (pulsed) 184 450 A PTOT Total dissipation at TC = 25°C 35 250 W dv/dt Peak diode recovery voltage slope VISO Insulation withstand voltage (RMS) from all three leads to external heat sink (t = 1 s; TC = 25 °C) 22 V/ns 2500 V EAS (3) Single pulse avalanche energy 125 mJ Tj Operating junction temperature storage temperature - 55 to 175 °C Tstg 1. Current limited by package. 2. Pulse width limited by safe operating area. 3. Starting Tj = 25 °C, ID = 50 A, VDD = 50 V for TO-220 and H2PAK-2; Starting Tj = 25 °C, ID = 29 A, VDD = 60 V for I2PAKFP and TO-220FP. Table 3. Thermal data Value Symbol Parameter TO-220FP I²PAKFP Rthj-case Thermal resistance junction-case Rthj-a Thermal resistance junction-ambient Rthj-pcb(1) Thermal resistance junction-pcb 4.3 Unit H²PAK-2 TO-220 0.6 62.5 35 0.6 °C/W 62.5 °C/W °C/W 1. When mounted on FR-4 board, on 1inch², 2oz Cu. Doc ID 018492 Rev 3 3/23 Electrical characteristics 2 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Electrical characteristics (TCASE = 25 °C unless otherwise specified) Table 4. Symbol On/off states Parameter Test conditions Min. Typ. 100 - Unit Drain-source breakdown voltage VGS= 0, ID = 250 µA IDSS Zero gate voltage drain current VGS = 0, VDS= 100 V TC=25°C TC=125°C - 10 100 µA µA IGSS Gate body leakage current VDS = 0, VGS = ±20 V - ±200 nA - 4 V 8 9.6 V(BR)DSS VGS(th) Gate threshold voltage VDS= VGS, ID = 250 µA 2 VGS= 10 V, ID= 23A TO-220FP and I²PAKFP RDS(on) Table 5. Symbol Static drain-source onresistance Parameter Test conditions VGS = 0, VDS = 25 V, f = 1 MHz Qg Qgs Qgd Total gate charge Gate-source charge Gate-drain charge VDD = 50 V, ID = 120 A, VGS = 10 V (see Figure 20) td(on) tr td(off) tf 7.8 8 9.3 9.6 Typ. Max. Unit - pF pF pF - 57 22 17 - nC nC nC Min. Typ. Max. Unit - 17 38 52 7.2 - ns ns ns ns Dynamic Input capacitance Output capacitance Reverse transfer capacitance Symbol V mΩ VGS= 10 V, ID= 60 A H²PAK TO-220 Ciss Coss Crss Table 6. 4/23 Max. Min. - 3305 373 23 Switching times Parameter Turn-on delay time Rise time Turn-off delay time Fall time Test conditions VDD = 50 V, ID = 60 A RG = 4.7 Ω VGS = 10 V (see Figure 19, Figure 24) Doc ID 018492 Rev 3 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Table 7. Symbol ISD ISDM(1) ISD ISDM(2) Electrical characteristics Source drain diode Parameter Test conditions Min. Typ. Max. Unit Source-drain current Source-drain current (pulsed) For TO-220FP and I²PAKFP - 46 184 A A Source-drain current Source-drain current (pulsed) For TO-220, H²PAK-2 - 120 450 A A - 1.5 V ISD=120 A, VGS=0; for TO-220, H²PAK-2 VSD(3) trr Qrr IRRM Forward on voltage Reverse recovery time Reverse recovery charge Reverse recovery current ISD=46 A, VGS=0; for TO-220FP and I²PAKFP ISD=120 A, di/dt = 100 A/µs, VDD=80 V, Tj=150 °C (see Figure 21) - 68 182 5.4 ns nC A 1. Pulse width limited by safe operating area 2. Pulse width limited by safe operating area 3. Pulsed: pulse duration = 300 µs, duty cycle 1.5% Doc ID 018492 Rev 3 5/23 Electrical characteristics STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 2.1 Electrical characteristics (curves) Figure 2. Safe operating area for TO-220FP and I²PAKFP Figure 3. Thermal impedance for TO-220FP and I²PAKFP Figure 5. Thermal impedance for H²PAK-2 and TO-220 AM11305v1 ID (A) ea ar 100 Tj=175°C Tc=25°C Single pulse is n) is DS(o th in ax R it on y m a er d b Op ite m i L 10 100µs 1ms 1 10ms 0.1 0.1 10 1 Figure 4. VDS(V) Safe operating area for H²PAK-2 and TO-220 AM11304v1 ID (A) 280TOEG K ea ar 100 Tj=175°C Tc=25°C Single pulse is n) 0.2 (o is DS th in ax R ion y m t a er d b Op ite Lim 10 δ=0.5 -1 0.1 10 0.05 100µs 0.02 0.01 -2 1ms 1 Zth=k Rthj-c δ=tp/τ 10 10ms Single pulse tp τ -3 0.1 0.1 Figure 6. 10 1 10 -6 10 VDS(V) Output characteristics Figure 7. AM11306v1 ID (A) VGS=10V 250 -5 10 -4 10 -3 10 -1 -2 10 10 0 10 tp (s) Transfer characteristics AM11307v1 ID (A) VDS=6V 250 7V 200 200 150 150 100 100 6V 50 50 0 0 6/23 1 2 3 4 5 6 7 8 VDS(V) 0 0 Doc ID 018492 Rev 3 2 4 6 8 VGS(V) STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Figure 8. Static drain-source on-resistance for TO-220FP and I²PAKFP AM11310v1 RDS(on) (mΩ) VGS=10V Figure 9. Electrical characteristics Static drain-source on-resistance for H²PAK-2 AM11309v1 RDS(on) (mΩ) VGS=10V 10.0 9.5 9.5 9.0 9.0 8.5 8.5 8.0 8.0 7.5 7.5 7.0 7.0 6.5 5 10 15 20 25 30 35 40 45 ID(A) Figure 10. Static drain-source on-resistance for TO-220 AM11308v1 RDS(on) (mΩ) 6.5 0 20 40 60 80 100 120 ID(A) Figure 11. Normalized BVDSS vs temperature AM11318v1 BVDSS (norm) VGS=10V ID=250µA 10.0 1.10 9.5 9.0 1.05 8.5 1.00 8.0 7.5 0.95 7.0 6.5 0 20 40 60 80 100 120 ID(A) 0.90 -75 25 -25 75 125 175 TJ(°C) Figure 12. Gate charge vs gate-source voltage Figure 13. Capacitance variations AM11311v1 VGS (V) AM11312v1 C (pF) VDD=50V ID=120A 12 f = 1 MHz 10000 10 Ciss 8 1000 6 Coss 4 100 Crss 2 10 0 0 10 20 30 40 50 60 70 Qg(nC) Doc ID 018492 Rev 3 0.1 1 10 100 VDS(V) 7/23 Electrical characteristics STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Figure 14. Normalized gate threshold voltage vs temperature AM11313v1 VGS(th) (norm) Figure 15. Normalized on-resistance vs temperature for TO-220FP and I²PAKFP AM11315v1 RDS(on) (norm) VGS=10V ID=23A ID=250µA 1.2 2.1 1.0 1.7 0.8 1.3 0.6 0.9 0.4 0.2 -75 -25 25 75 125 TJ(°C) 175 Figure 16. Normalized on resistance vs temperature for H²PAK-2 and TO-220 AM11314v1 RDS(on) (norm) VGS=10V ID=60A 0.5 -75 -25 25 75 125 175 TJ(°C) Figure 17. Source-drain diode forward characteristics for TO-220FP and I²PAKFP AM11317v1 VSD (V) 1.0 2.1 TJ=-55°C 0.9 1.7 0.8 TJ=25°C 0.7 1.3 0.6 0.9 0.5 0.5 -75 8/23 TJ=175°C 0.4 -25 25 75 125 175 TJ(°C) Doc ID 018492 Rev 3 0 5 10 15 20 25 30 35 40 45 ISD(A) STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Electrical characteristics Figure 18. Source-drain diode forward characteristics for H²PAK-2 and TO-220 AM11316v1 VSD (V) 1.0 TJ=-55°C 0.9 TJ=25°C 0.8 0.7 TJ=175°C 0.6 0.5 0.4 0 20 40 60 80 100 120 ISD(A) Doc ID 018492 Rev 3 9/23 Test circuits 3 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Test circuits Figure 19. Switching times test circuit for resistive load Figure 20. Gate charge test circuit VDD 12V 47kΩ 1kΩ 100nF 3.3 μF 2200 RL μF VGS IG=CONST VDD 100Ω Vi=20V=VGMAX VD RG 2200 μF D.U.T. D.U.T. VG 2.7kΩ PW 47kΩ 1kΩ PW AM01468v1 AM01469v1 Figure 21. Test circuit for inductive load Figure 22. Unclamped inductive load test switching and diode recovery times circuit A A D.U.T. FAST DIODE B B L A D G VD L=100μH S 3.3 μF B 25 Ω 1000 μF D VDD 2200 μF 3.3 μF VDD ID G RG S Vi D.U.T. Pw AM01470v1 Figure 23. Unclamped inductive waveform AM01471v1 Figure 24. Switching time waveform ton V(BR)DSS tdon VD toff tr tdoff tf 90% 90% IDM 10% ID VDD 10% 0 VDD VDS 90% VGS AM01472v1 10/23 0 Doc ID 018492 Rev 3 10% AM01473v1 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 4 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Doc ID 018492 Rev 3 11/23 Package mechanical data Table 8. STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 TO-220FP mechanical data mm Dim. Min. Max. A 4.4 4.6 B 2.5 2.7 D 2.5 2.75 E 0.45 0.7 F 0.75 1 F1 1.15 1.70 F2 1.15 1.70 G 4.95 5.2 G1 2.4 2.7 H 10 10.4 L2 12/23 Typ. 16 L3 28.6 30.6 L4 9.8 10.6 L5 2.9 3.6 L6 15.9 16.4 L7 9 9.3 Dia 3 3.2 Doc ID 018492 Rev 3 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Package mechanical data Figure 25. TO-220FP drawing 7012510_Rev_K_B Doc ID 018492 Rev 3 13/23 Package mechanical data Table 9. STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 I2PAKFP (TO-281) mechanical data mm Dim. Min. Typ. Max. A 4.40 4.60 B 2.50 2.70 D 2.50 2.75 D1 0.65 0.85 E 0.45 0.70 F 0.75 1.00 F1 1.20 G 4.95 H 10.00 10.40 L1 21.00 23.00 L2 13.20 14.10 L3 10.55 10.85 L4 2.70 3.20 L5 0.85 1.25 L6 7.30 7.50 - 5.20 Figure 26. I2PAKFP (TO-281) drawing REV! 14/23 Doc ID 018492 Rev 3 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Table 10. Package mechanical data H²PAK-2 mechanical data mm Dim. Min. Typ. Max. A 4.30 4.80 A1 0.03 0.20 C 1.17 1.37 e 4.98 5.18 E 0.50 0.90 F 0.78 0.85 H 10.00 10.40 H1 7.40 7.80 - L 15.30 15.80 L1 1.27 1.40 L2 4.93 5.23 L3 6.85 7.25 L4 1.5 1.7 M 2.6 2.9 R 0.20 0.60 V 0° 8° Doc ID 018492 Rev 3 15/23 Package mechanical data STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Figure 27. H²PAK-2 drawing 8159712_C 16/23 Doc ID 018492 Rev 3 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Package mechanical data Figure 28. H²PAK-2 recommended footprint (dimensions are in millimeters) 8159712_C Doc ID 018492 Rev 3 17/23 Package mechanical data Table 11. STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 TO-220 type A mechanical data mm Dim. Min. Max. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 D1 18/23 Typ. 1.27 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 1.23 1.32 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 ∅P 3.75 3.85 Q 2.65 2.95 Doc ID 018492 Rev 3 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Package mechanical data Figure 29. TO-220 type A drawing 0015988_typeA_Rev_S Doc ID 018492 Rev 3 19/23 Package mechanical data 5 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Package mechanical data Table 12. H²PAK-2 tape and reel mechanical data Tape Reel mm mm Dim. 20/23 Dim. Min. Max. Min. A0 10.5 10.7 A B0 15.7 15.9 B 1.5 D 1.5 1.6 C 12.8 D1 1.59 1.61 D 20.2 E 1.65 1.85 G 24.4 F 11.4 11.6 N 100 K0 4.8 5.0 T P0 3.9 4.1 P1 11.9 12.1 Base qty 1000 P2 1.9 2.1 Bulk qty 1000 R 50 T 0.25 0.35 W 23.7 24.3 Doc ID 018492 Rev 3 Max. 330 13.2 26.4 30.4 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Package mechanical data Figure 30. Tape 10 pitches cumulative tolerance on tape +/- 0.2 mm T P0 Top cover tape P2 D E F W K0 B0 A0 P1 D1 User direction of feed R Bending radius User direction of feed AM08852v2 Figure 31. Reel T REEL DIMENSIONS 40mm min. Access hole At sl ot location B D C N A Full radius Tape slot in core for tape start 25 mm min. width G measured at hub AM08851v2 Doc ID 018492 Rev 3 21/23 Revision history 6 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Revision history Table 13. Document revision history Date Revision 24-Feb-2011 1 First version. 07-May-2012 2 Added Section 2.1: Electrical characteristics (curves). Minor text changes. 3 Added new device in I2PAKFP and updated the document accordingly. Updated Section 4: Package mechanical data. 07-Nov-2012 22/23 Changes Doc ID 018492 Rev 3 STF130N10F3, STFI130N10F3, STH130N10F3-2, STP130N10F3 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 018492 Rev 3 23/23