0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
SY88289CLMG

SY88289CLMG

  • 厂商:

    ACTEL(微芯科技)

  • 封装:

    VFQFN16_4X4MM_EP

  • 描述:

    IC POST AMP 3.3V 3.2GBPS 16-MLF

  • 数据手册
  • 价格&库存
SY88289CLMG 数据手册
SY88289CL 3.3V, 3.2Gbps CML Limiting Post Amplifier with High-Gain TTL Loss-of-Signal General Description Features The SY88289CL low-power, high-sensitivity, limiting post amplifier is designed for use in fiber-optic receivers. The device connects to typical transimpedance amplifiers (TIAs). The linear signal output from TIAs can contain significant amounts of noise and may vary in amplitude over time. The SY88289CL quantizes these signals and outputs CML-level waveforms. The SY88289CL operates from a single +3.3V power o o supply, over temperatures ranging from –40 C to +85 C. With its wide bandwidth and high gain, signals with data rates up to 3.2Gbps and as small as 5mVPP can be amplified to drive devices with CML inputs or ACcoupled CML/PECL inputs. The SY88289CL generates a high-gain loss-of-signal (LOS) open-collector TTL output. This function has a high-gain input stage for increased LOS sensitivity. A programmable loss-of-signal level-set pin (LOSLVL) sets the sensitivity of the input amplitude detection. LOS asserts high if the input amplitude falls below the threshold sets by LOSLVL and de-asserts low otherwise. The enable bar input (/EN) de-asserts the true output signal without removing the input signal. The LOS output can be fed back to the /EN input to maintain output stability under a loss-of-signal condition. Typically, 3.5dB LOS hysteresis is provided to prevent chattering. All support documentation can be found on Micrel’s web site at: www.micrel.com. • • • • • • • • • Single 3.3V power supply 125Mbps to 3.2Gbps operation Low-noise CML data outputs High-gain LOS Chatter-free open-collector TTL Loss-of-Signal (LOS) output with an internal 4.75kΩ pull -up resistor TTL /EN input Programmable LOS level set (LOSLVL) Ideal for multi-rate applications Available in a tiny (3mm x 3mm) 16-pin QFN package Applications • • • • • • APON, BPON, EPON, GEPON and GPON Gigabit Ethernet 1X and 2X Fibre Channel SONET/SDH : OC 3/12/24/48 – STM 1/4/8/16 High-gain line driver and line receiver Low-gain TIA interface Markets • • • • FTTP/FTTH Optical transceivers Datacom/Telecom Long reach FOM Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com February 2007 M9999-021207-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88289CL Typical Application Ordering Information Part Number Package Type Operating Range Package Marking Lead Finish QFN-16 Industrial 289C with Pb-Free bar line indicator NiPdAu Pb-Free QFN-16 Industrial 289C with Pb-Free bar line indicator NiPdAu Pb-Free SY88289CLMG (1) SY88289CLMGTR Note: 1. Tape and Reel. Pin Configuration 16-Pin QFN February 2007 2 M9999-021207-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88289CL Pin Description Pin Number Pin Name Type Pin Function 1, 12 VCC Power Supply 2 DIN Data Input True data input. 3 /DIN Data Input Complementary data input. 4, 9 GND Ground 5 VREF 6 LOSLVL Positive power supply. Device ground. Reference voltage: Placing a capacitor here to VCC helps stabilize LOSLVL. Input Loss-of-signal Level Set: a resistor from this pin to VCC sets the threshold for the data input amplitude at which LOS will be asserted. 7, 14, 15, 16 N/C 8 LOS Open-collector TTL output w/internal 4.75kΩ pull-up resistor 10 /DOUT CML Output Complementary data output. 11 DOUT CML Output True data output. 13 /EN TTL Input: Default is HIGH. February 2007 No connect. Loss-of-signal: asserts high when the data input amplitude falls below the threshold sets by LOSLVL. /Enable: This input enables the outputs when it is LOW. Note that this input is internally connected to a 25kΩ pull-up resistor and will default to a logic HIGH state if left open. 3 M9999-021207-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88289CL Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VCC) .................................... 0V to +4.0V Input Voltage (DIN, /DIN) ................................... 0 to VCC Output Current (IOUT) Continuous……………………………………±25mA /EN Voltage ........................................................ 0 to VCC VREF Current……………………………-800uA to +500uA LOSLVL Voltage .............................................. VREF to VCC Lead Temperature (soldering, 20sec.) .................. 260°C Storage Temperature (Ts) .....................-65°C to +150°C Supply Voltage (VCC).............................. +3.0V to +3.6V Ambient Temperature (TA) ....................–40°C to +85°C Junction Temperature (TJ) ..................–40°C to +125°C Junction Thermal Resistance QFN (θJA) Still-air ..................................................... 61°C/W QFN (ΨJB) o Junction-to-board .....................................38 C/W DC Electrical Characteristics VCC = 3.0V to 3.6V; RL = 50Ω to V CC; TA = –40°C to +85°C. Symbol Parameter Condition ICC Power Supply Current No output load LOSLVL LOSLVL Voltage VOH CML Output HIGH Voltage VOL CML Output LOW Voltage VOFFSET Differential Output Offset VREF Reference Voltage VIHCMR Input Common Mode Range Min Typ Max Units 42 62 mA VCC V VCC-0.020 VCC-0.005 VCC V VCC-0.475 VCC-0.400 VCC-0.350 V ±80 mV VREF VCC = 3.3V VCC-1.28 GND+2.0 V VCC V Max Units TTL DC Electrical Characteristics VCC = 3.0V to 3.6V; RL = 50Ω to V CC; TA = –40°C to +85°C. Symbol Parameter VIH /EN Input HIGH Voltage VIL /EN Input LOW Voltage IIH /EN Input HIGH Current IIL /EN Input LOW Current VOH LOS Output High Level VOL LOS Output LOW Level Condition Min Typ 2.0 0.8 V VIN = 2.7V 20 µA VIN = VCC 100 µA VIN = 0.5V Vout ≥ 3.3V, IOH (MAX) < 160 uA -300 uA 2.4 V Vout < 3.3V, IOH (MAX) < 160 uA 2.0 V Sinking 2mA 0.5 V Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the device’s most negative potential (GND) on the PCB. ΨJB uses 4-layer (θJA) in still-air-number, unless otherwise stated. February 2007 4 M9999-021207-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88289CL AC Electrical Characteristics VCC = 3.0V to 3.6V; RL = 50Ω to V CC; TA = –40°C to +85°C. Symbol Parameter Condition tr , tf Output Rise/Fall Time (20% to 80%) tJITTER Min Typ Max Note 4 60 120 Deterministic Note 5 15 psPP Random Note 6 5 psRMS VID Differential Input Voltage Swing Figure 1 VOD Differential Output Voltage Swing VID > 12mVPP, Figure 1 TOFF LOS Release Time TON LOS Assert Time LOSAL Low LOS Assert Level RLOSLVL = 15kΩ, Note 8 3 mVPP LOSDL Low LOS De-assert Level RLOSLVL = 15kΩ, Note 8 4.5 mVPP HYSL Low LOS Hysteresis RLOSLVL = 15kΩ, Note 7 3.5 dB LOSAM Medium LOS Assert Level RLOSLVL = 5kΩ, Note 8 5 mVPP 5 700 2 Units ps 1800 mVPP 800 950 mVPP 2 10 μs 2 10 μs LOSDM Medium LOS De-assert Level RLOSLVL = 5kΩ, Note 8 7.5 11 mVPP HYSM Medium LOS Hysteresis RLOSLVL = 5kΩ, Note 7 2 3.5 4.5 dB LOSAH High LOS Assert Level RLOSLVL = 100Ω, Note 8 8 12 LOSDH High LOS De-assert Level RLOSLVL = 100Ω, Note 8 18 23 mVPP HYSH High LOS Hysteresis RLOSLVL = 100Ω, Note 7 2 3.5 4.5 dB B-3dB 3dB Bandwidth AV(Diff) Differential Voltage Gain S21 Single-ended Small-Signal Gain mVPP 2 GHz 32 38 dB 26 32 dB Notes: 4. Amplifier in limiting mode. Input is a 200MHz square wave. 5. Deterministic jitter measured using 3.2Gbps K28.5 pattern, VID = 10mVPP. 6. Random jitter measured using 3.2Gbps K28.7 pattern, VID = 10mVPP. 7. This specification defines electrical hysteresis as 20log (LOS De-assert/LOS Assert). The ratio between optical hysteresis and electrical hysteresis is found to vary between 1.5 and 2, depending upon the level of received optical power and ROSA characteristics. Based upon that ratio, the optical hysteresis corresponding to the electrical hysteresis range 2dB-4.5dB, as shown in the AC characteristics table, will be 1dB-3dB. 8. See “Typical Operating Characteristics” for a graph showing how to choose a particular RLOSLVL for a particular LOS assert and its associated de-assert amplitude. February 2007 5 M9999-021207-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88289CL Typical Operating Characteristics February 2007 6 M9999-021207-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88289CL Functional Block Diagram Detailed Description Loss-of-signal The SY88289CL generates a chatter-free LOS opencollector TTL output with an internal 4.75k Ω pull -up resistor, as shown in Figure 4. LOS is used to determine that the input amplitude is large enough to be considered a valid input. LOS asserts high if the input amplitude falls below the threshold sets by LOSLVL and de-asserts low otherwise. LOS can be fed back to the enable bar (/EN) input to maintain output stability under a loss of signal condition. /EN deasserts the true output signal without removing the input signals. Typically, 3.5dB LOS hysteresis is provided to prevent chattering. Loss-of-signal Level Set A programmable LOS level-set pin (LOSLVL) sets the threshold of the input amplitude detection. Connecting an external resistor between VCC and LOSLVL sets the voltage at LOSLVL. This voltage ranges from VCC to VREF. The external resistor creates a voltage divider between VCC and VREF, as shown in Figure 5. Hysteresis The SY88289CL typically provides 3.5dB LOS electrical hysteresis. By definition, a power ratio measured in dB is 10log (power ratio). Power is 2 calculated as V IN/R for an electrical signal. Hence, the same ratio can be stated as 20log (voltage ratio). While in linear mode, the electrical voltage input changes linearly with the optical power and therefore, the ratios change linearly. Thus, the optical hysteresis in dB is half the electrical hysteresis in dB given in the data sheet. Since the SY88289CL is an electrical device, this data sheet refers to hysteresis in electrical terms. With 3.5dB LOS hysteresis, a voltage factor of 1.5 is required to assert or de-assert LOS. The SY88289CL high-sensitivity limiting post amplifier operates from a single +3.3V power supply, over o o temperatures from –40 C to +85 C. Signals with data rates up to 3.2Gbps and as small as 5mVPP can be amplified. Figure 1 shows the allowed input voltage swing. The SY88289CL generates a LOS output. LOSLVL sets the sensitivity of the input amplitude detection. Input Amplifier/Buffer Figure 2 shows a simplified schematic of the SY88289CL’s input stage. The high-sensitivity of the input amplifier allows signals as small as 5mVPP to be detected and amplified. The input amplifier also allows input signals as large as 1800mVPP. Input signals are linearly amplified with a typical 38dB differential voltage gain. Since it is a limiting amplifier, the SY88289CL outputs typically 800mVPP voltage-limited waveforms for input signals that are greater than 12mVPP. Applications requiring the SY88289CL to operate with high-gain should have the upstream TIA placed as close as possible to the SY88289CL’s input pins to ensure the best performance of the device. Output Buffer The SY88289CL’s CML output buffer is designed to drive 50Ω lines. The output buffer requires appropriate termination for proper operation. An external Ω 50 resistor to VCC for each output pin provides this. Figure 3 shows a simplified schematic of the output stage. February 2007 7 M9999-021207-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88289CL Figure 1. VIS and VID Definition February 2007 Figure 2. Input Structure Figure 3. Output Structure Figure 4. Input Structure Figure 5. LOSLVL Setting Circuit 8 M9999-021207-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88289CL Package Information 16-Pin (3mm x 3mm) QFN February 2007 9 M9999-021207-B hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY88289CL PCB Thermal Consideration for 16-Pin QFN Package Package Notes: 1. Package meets Level 2 qualification. 2. All parts are dry-packaged before shipment. 3. Exposed pad must be soldered to a ground for proper thermal management. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. February 2007 10 M9999-021207-B hbwhelp@micrel.com or (408) 955-1690
SY88289CLMG 价格&库存

很抱歉,暂时无法提供与“SY88289CLMG”相匹配的价格&库存,您可以联系我们找货

免费人工找货