ALM-80210-BLKG

ALM-80210 0.25W Analog Variable Gain Amplifier Data Sheet Description Features Avago Technologies ALM-80210 is a 0.25W Analog Controlled Variable Gain Amplifier which operates from 1.6GHz to 2.7GHz. The device provides an exceptionally high OIP3 level of 39.5dBm, which is maintained over a wide attenuation range. The device features wide gain control range, low current, excellent input and output return loss. • Halogen free The ALM-80210 is housed in a miniature 5.0X5.0X1.1 mm3, 10-lead multiple-chips-on-board (MCOB) module package. This part is suitable for the AGC/Temperature compensation circuits application in wireless infrastructure such as Cellular/PCS/W-CDMA/WLLand and new generation wireless technologies systems. Pin connections and Package Marking • Wide Gain Control Range • High OIP3 across attenuation range Specifications At 1.9GHz, Vdd = 5V, Itotal = 112mA (typ), Vbias = 4V, Vctrl = 5V @ 25°C • OIP3 = 40.5dBm • Noise Figure = 5.2dB • Gain = 9.8dB • P1dB = 23.2dBm • IRL = 13.6dB, ORL = 12.1dB • Dynamic Range = 35dB Application 80210 WWYY XXXX • CDMA, W-CDMA, WiMAX, LTE and other applications in the 1.6GHz to 2.7GHz range. • Transmitter and Receiver Gain Control Attention: Observe precautions for handling electrostatic sensitive devices. ESD Machine Model = 90 V ESD Human Body Model = 650 V Refer to Avago Application Note A004R: Electrostatic Discharge, Damage and Control. 10 Not used 9 EXT Lout 8 GND 7 Vctrl • Temperature Compensation Circuitry 6 RFout Vdd RFin 1 C Not used 2 Vbias 3 GND 4 GND 5 C Note : Top View : Package marking provides orienation and identification “80210” = Device Code “WWYY“ = Workweek and Year Code  “XXXX” = Assembly Lot number L C RFin C C C Vctrl RFout Vbias Figure 1. Simplified Schematic diagram ALM-80210 Absolute Maximum Rating (1) TC = 25°C Thermal Resistance (2,3) Symbol Parameter Units Absolute Maximum Id,max Drain Current mA 140 Vd.,max Drain Voltage, RF output to ground V 5.5 Vctrl_max Control Voltage V 7 Vbias_max Biasing Voltage V 15 Pd Power Dissipation mW 770 Pin CW RF Input Power (4) dBm 25 Tj Junction Temperature °C 150 TSTG Storage Temperature °C -65 to 150 (Vd = 5.0V) θjc = 70°C/W Notes: 1. Operation of this device in excess of any of these limits may cause permanent damage 2. Derate 14.3mW/°C for TL > 97°C 3. Thermal resistance measured using 150°C Infra-Red Microscopy Technique. 4. Max rating for Pin is under maximum attenuation condition i.e. Vctrl = 1V. ALM-80210 Electrical Specification (1) TC = 25°C, Zo = 50Ω, Vdd = 5.0V, Vbias = 4V, Vctrl = 5V unless noted Symbol Parameter and Test Condition Frequency Units Min. Typ. Max. stdev(4) Idd Operating Amplifier Current Range N/A mA 89 112 134 0.002 NF Noise Figure at minimal Attenuation 1.9GHz 2.1GHz 2.5GHz dB 5.2 5.4 5.7 5.9 0.088 Gain Gain at minimal Attenuation 1.9GHz 2.1GHz 2.5GHz dB 8.2 9.8 9.7 9.5 11.2 0.148 OIP3(2) Output Third Order Intercept Point 1.9GHz 2.1GHz 2.5GHz dBm 36 40.5 39.5 39.8 0.616 P1dB Output Power at 1dB Gain Compression 1.9GHz 2.1GHz 2.5GHz dBm 22 23.5 23..5 23.3 0.112 IRL Input Return Loss 1.9GHz 2.1GHz 2.5GHz dB 13.6 14.9 18.5 NA ORL Output Return Loss 1.9GHz 2.1GHz 2.5GHz dB 12.1 14.3 14.8 NA ISO Isolation 1.9GHz 2.1GHz 2.5GHz dB 28.6 27.7 26.7 NA Vbias Attenuator Bias Voltage N/A V 2.7 4 5 N/A Vctrl Gain Variation Control Voltage N/A V 1 – 5 NA ∆ Gain Gain Variation Range (from Vctrl=1V to 5V) 1.9GHz 2.1GHz 2.5GHz dB 35.0 35.1 34.3 NA Note : 1. Measurements obtained from a test circuit described in Figure 53. 2. OIP3 test condition: F1 – F2 = 10MHz, with input power of -10dBm per tone measured at worst case side band. 3. Standard deviation data are based on at least 1000 pieces samples size taken from 2 wafer lots. Future wafers allocated to this product may have nominal values anywhere between the upper and lower specification limits. 2 ALM-80210 Product Consistency Distribution at 1900MHz TC = 25°C, Vdd = 5.0V, Vbias = 4.0V LSL USL USL CPK=3.1 .09 .10 .11 .12 CPK=2.2 4.8 4.9 .13 Figure 2. Itotal at 1900MHz 5.0 5.1 5.2 5.3 5.4 Figure 3. NF at 1900MHz LSL USL LSL CPK=3.2 9 10 CPK=2.7 11 Figure 4. Gain at 1900MHz Figure 6. P1dB at 1900MHz 3 37 38 39 40 41 42 43 44 45 46 47 48 49 Note : 1. Statistics distribution determined from a sample size of 1000 parts taken from 2 different wafers. 2. Future wafers allocation to this product may have typical values anywhere between the minimum and maximum specification limits. 3. Measurements are made on production testboard, which represents a trade-off between optimal OIP3, P1dB and NF. Circuit losses have been de-embedded from actual measurements. CPK=4.9 23 36 Figure 5. OIP3 at 1900MHz LSL 22 5.5 5.6 5.7 5.8 5.9 24 25 ALM-80210 Application Circuit Data for 1900MHz TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 44 42 P1dB (dBm) OIP3 (dBm) 40 38 36 34 85°C 25°C -40°C 32 30 1 1.5 2 2.5 3 Vctrl (V) 3.5 4 4.5 5 Figure 7. OIP3 vs Control Voltage and Temperature at 1900MHz 10 5 -5 IRL (dB) Gain (dB) 0 -10 -15 85°C 25°C -40°C -20 -25 1.5 2.0 2.5 3.0 3.5 Vctrl (V) 4.0 4.5 5.0 Figure 9. Gain vs Control Voltage and Temperature at 1900MHz -9 -10 Isolation (dB) ORL (dB) -11 -12 -13 -14 85°C 25°C -40°C -15 -16 1 1.5 2 2.5 3 3.5 Vctrl (V) 4 Figure 11. ORL vs Control Voltage and Temperature at 1900MHz 4 1 1.5 2 2.5 3 3.5 Vctrl (V) 4 4.5 5 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 85°C 25°C -40°C 1 1.5 2 2.5 3 Vctrl (V) 3.5 4 4.5 5 Figure 10. IRL vs Control Voltage and Temperature at 1900MHz -8 -17 85°C 25°C -40°C Figure 8. P1dB vs Control Voltage and Temperature at 1900MHz 15 -30 1.0 25.0 24.0 23.0 22.0 21.0 20.0 19.0 18.0 17.0 16.0 15.0 4.5 5 -20 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 85°C 25°C -40°C 1 1.5 2 2.5 3 3.5 Vctrl (V) 4 4.5 Figure 12. Isolation vs Control Voltage and Temperature at 1900MHz 5 ALM-80210 Application Circuit Data for 1900MHz (cont'd) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 44 85°C 25°C -40°C 42 P1dB (dBm) OIP3 (dBm) 40 38 36 34 32 30 0 10 20 Attenuation(dB) 30 40 Figure 13. OIP3 vs Attenuation and Temperature at 1900MHz -9 -10 -12 IRL (dB) ORL (dB) -11 -13 -14 85°C 25°C -40°C -16 -17 0 10 20 Attenuation (dB) 30 40 10 20 Attenuation (dB) 30 40 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 -22 85°C 25°C -40°C 0 10 20 Attenuation (dB) 30 40 48 85°C 25°C -40°C 85°C 25°C -40°C 46 44 42 40 38 0 10 20 Attenuation (dB) 30 Figure 17. Isolation vs Attenuation and Temperature at 1900MHz 5 0 Figure 16. IRL vs Attenuation and Temperature at 1900MHz OIP3 (dBm) Isolation (dB) Figure 15. ORL vs Attenuation and Temperature at 1900MHz -20 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 85°C 25°C -40°C Figure 14. P1dB vs Attenuation and Temperature at 1900MHz -8 -15 26 25 24 23 22 21 20 19 18 17 16 15 40 36 1600 1700 1800 1900 2000 Frequency (MHz) 2100 Figure 18. OIP3 vs Frequency and Temperature at Vctrl = 5V 2200 ALM-80210 Application Circuit Data for 1900MHz (cont'd) 24.6 24.4 24.2 24.0 23.8 23.6 23.4 23.2 23.0 22.8 22.6 1600 13 85°C 25°C -40°C 11 10 9 8 1700 1800 1900 2000 Frequency (MHz) 2100 7 1600 2200 Figure 19. P1dB vs Frequency and Temperature at Vctrl = 5V 1700 1800 1900 2000 Frequency (MHz) 2100 2200 Figure 20. Gain vs Frequency and Temperature at Vctrl = 5V -8 -6 85°C 25°C -40°C -9 -10 85°C 25°C -40°C -8 -10 -11 ORL (dB) IRL (dB) 85°C 25°C -40°C 12 Gain (dB) P1dB (dBm) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V -12 -13 -12 -14 -14 -16 -15 -16 1600 1700 1800 1900 2000 Frequency (MHz) 2100 85°C 25°C -40°C 1700 1800 1900 2000 Frequency (MHz) 2100 Figure 23. Isolation Frequency and Temperature at Vctrl = 5V 6 1700 1800 1900 2000 Frequency (MHz) 2100 2200 Figure 22. ORL vs. Frequency and Temperature at Vctrl = 5V Gain (dB) Isolation (dB) Figure 21. IRL vs Frequency and Temperature at Vctrl = 5V -26 -26.5 -27 -27.5 -28 -28.5 -29 -29.5 -30 -30.5 -31 1600 -18 1600 2200 2200 20 15 10 5 0 -5 -10 -15 -20 -25 -30 1600 Vctrl=5V Vctrl=4V Vctrl=3V Vctrl=1.5V Vctrl=2V Vctrl=1V 1700 1800 1900 2000 Frequency (MHz) Figure 24. Gain vs Frequency and Control Voltage 2100 2200 ALM-80210 Application Circuit Data for 1900MHz (cont'd) 7 120 6.5 115 6 110 5.5 105 Idd (mA) NF (dB) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 5 4.5 4 3 1600 1700 1800 1900 2000 Frequency (MHz) 2100 95 85 80 2200 Figure 25. Noise Figure vs Frequency and Temperature at Vctrl = 5V 1 1.5 2 2.5 3 3.5 Vctrl (V) 4 14 12 Ictrl (mA) 2 1.5 1 10 8 6 4 0.5 1 1.5 2 2.5 3 Vctrl (V) 3.5 4 4.5 5 20 Phase (Degree) 0 -20 -40 -60 -80 85°C 25°C -40°C -100 0 10 20 Attenuation (dB) 30 Figure 29. Phase vs Attenuation and Temperature at 1900MHz (without external L1 as shown in Figure 54) 0 1 1.5 2 2.5 3 Vctrl (V) 3.5 4 Figure 28. Current (Ictrl) vs Control Voltage and Temperature 40 7 85°C 25°C -40°C 2 Figure 27. Current (Ibias) vs Control Voltage and Temperature -120 5 16 85°C 25°C -40°C 2.5 0 4.5 Figure 26. Current (Idd) vs Control Voltage and Temperature 3 Ibias (mA) 100 90 85°C 25°C -40°C 3.5 85°C 25°C -40°C 40 4.5 5 ALM-80210 Application Circuit Data for 2500MHz TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 46 44 40 P1dB (dBm) OIP3 (dBm) 42 38 36 34 85°C 25°C -40°C 32 30 28 1 1.5 2 2.5 3 Vctrl (V) 3.5 4 4.5 5 Figure 30. OIP3 vs Control Voltage and Temperature at 2500MHz 10 5 -5 IRL (dB) Gain (dB) 0 -10 -15 85°C 25°C -40°C -25 -30 1 1.5 2 2.5 3 Vctrl (V) 3.5 4 4.5 5 1.5 2 2.5 3 3.5 Vctrl (V) 4 4.5 5 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 85°C 25°C -40°C 1 1.5 2 2.5 3 3.5 Vctrl (V) 4 4.5 5 -20 85°C 25°C -40°C -25 -30 -35 -40 -45 -50 85°C 25°C -40°C -55 -60 1 1.5 2 2.5 3 Vctrl (V) 3.5 4 Figure 34. ORL vs Control Voltage and Temperature at 2500MHz 8 1 Figure 33. IRL vs Control Voltage and Temperature at 2500MHz Isolation (dB) ORL (dB) Figure 32. Gain vs Control Voltage and Temperature at 2500MHz -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 85°C 25°C -40°C Figure 31. P1dB vs Control Voltage and Temperature at 2500MHz 15 -20 25 24 23 22 21 20 19 18 17 16 15 4.5 5 -65 1 1.5 2 2.5 3 3.5 Vctrl (V) 4 4.5 Figure 35. Isolation vs Control Voltage and Temperature at 2500MHz 5 ALM-80210 Application Circuit Data for 2500MHz (cont'd) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 46 85°C 25°C -40°C 44 40 P1dB (dBm) OIP3 (dBm) 42 38 36 34 32 30 28 0 10 20 Attenuation (dB) 30 40 -8 -9 -10 -11 -12 -13 -14 -15 -16 -17 -18 85°C 25°C -40°C 0 10 20 Attenuation (dB) 30 40 Figure 38. ORL vs Attenuation and Temperature at 2500MHz -30 20 Attenuation (dB) 30 40 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 85°C 25°C -40°C 0 10 20 Attenuation (dB) 30 40 85°C 25°C -40°C 46 -35 OIP3 (dBm) Isolation (dB) 10 48 85°C 25°C -40°C -25 -40 -45 -50 -55 44 42 40 38 -60 0 10 20 Attenuation (dB) 30 Figure 40. Isolation vs Attenuation and Temperature at 2500MHz 9 0 Figure 39. IRL vs Attenuation and Temperature at 2500MHz -20 -65 85°C 25°C -40°C Figure 37. P1dB vs Attenuation and Temperature at 2500MHz IRL (dB) ORL (dB) Figure 36. OIP3 vs Attenuation and Temperature at 2500MHz 25 24 23 22 21 20 19 18 17 16 15 40 36 2200 2300 2400 2500 2600 Frequency (MHz) 2700 Figure 41. OIP3 vs Frequency and Temperature at Vctrl = 5V 2800 ALM-80210 Application Circuit Data for 2500MHz (cont'd) 24.5 24.3 24.1 23.9 23.7 23.5 23.3 23.1 22.9 22.7 22.5 2200 12 85°C 25°C -40°C 11 10 Gain (dB) P1dB (dBm) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 8 2300 2400 2500 2600 Frequency (MHz) 2700 2400 2500 2600 Frequency (MHz) 2700 2800 -6 85°C 25°C -40°C -8 -10 ORL (dB) IRL (dB) -12 -14 -16 -18 2300 2400 2500 2600 Frequency (MHz) 2700 -20 2200 2800 85°C 25°C -40°C 2300 2400 2500 2600 Frequency (MHz) 2300 2400 2500 2600 Frequency (MHz) 2700 2800 Figure 45. ORL vs. Frequency and Temperature at Vctrl = 5V Gain (dB) Isolation (dB) 2300 Figure 43. Gain vs Frequency and Temperature at Vctrl = 5V 85°C 25°C -40°C 2700 Figure 46. Isolation Frequency and Temperature at Vctrl = 5V 10 6 2200 2800 Figure 44. IRL vs Frequency and Temperature at Vctrl = 5V -24 -24.5 -25 -25.5 -26 -26.5 -27 -27.5 -28 -28.5 -29 2200 85°C 25°C -40°C 7 Figure 42. P1dB vs Frequency and Temperature at Vctrl = 5V -10 -11 -12 -13 -14 -15 -16 -17 -18 -19 -20 -21 2200 9 2800 20 15 10 5 0 -5 -10 -15 -20 -25 -30 2200 Vctrl=5V Vctrl=4V Vctrl=3V Vctrl=2V Vctrl=1.5V Vctrl=1V 2300 2400 2500 2600 Frequency (MHz) Figure 47. Gain vs Frequency and Control Voltage 2700 2800 ALM-80210 Application Circuit Data for 2500MHz (cont'd) 8 7.5 7 6.5 6 5.5 5 4.5 4 3.5 3 2200 120 115 110 Idd (mA) NF (dB) TC = 25°C, Vdd = 5.0V, Vbias = 4.0V 2400 2500 2600 Frequency (MHz) 2700 95 85 80 2800 Figure 48. Noise Figure vs Frequency and Temperature at Vctrl = 5V 1 1.5 2 2.5 3 3.5 Vctrl (V) 4 14 12 Ictrl (mA) 2 1.5 1 10 8 6 4 0.5 1 1.5 2 2.5 3 Vctrl (V) 3.5 4 4.5 5 -40 -60 -80 -100 -120 -140 85°C 25°C -40°C -160 -180 0 10 20 Attenuation (dB) 30 Figure 52. Phase vs Attenuation and Temperature at 2500MHz (without external L1 as shown in Figure 54) 0 1 1.5 2 2.5 3 3.5 Vctrl (V) 4 Figure 51. Current (Ictrl) vs Control Voltage and Temperature -20 Phase (Degree) 85°C 25°C -40°C 2 Figure 50. Current (Ibias) vs Control Voltage and Temperature 11 5 16 85°C 25°C -40°C 2.5 0 4.5 Figure 49. Current (Idd) vs Control Voltage and Temperature 3 Ibias (mA) 100 90 85°C 25°C -40°C 2300 85°C 25°C -40°C 105 40 4.5 5 Application Circuit Description and Layout C5 L1 IN C2 C1 VBIAS L1 C6 C7 VDD Anggerik 5x5 A2 Rev2 VCTL GND C1 GND C2 C5 C6 C7 L4 L4 OUT C3 C3 Figure 53. Demoboard schematic and layout Bill of Materials Description Circuit Symbol Size For 1.9GHz C1 0402 0.4pF Murata NA C2 0402 27pF Murata 100pF Murata C3 0402 100pF Murata 100pF Murata C5 0603 2.2uF Murata 2.2uF Murata C6 0402 0.1uF Murata 0.1uF Murata C7 0402 15pF Murata 3pF Murata L1 0402 NA L4 0402 12nH For 2.5GHz NA Toko 3.9nH ALM-80210 is a input fully matched and output prematched product. The product requires 3 biasing points i.e. Vdd (to bias up the PA), Vbias and Vctrl (for controlling the attenuator circuitry). The Vdd is connected to the output pin thru a RF choke, L4 (which isolates the inband signal from the DC supply). The bypass capacitor (C5, C6 and C7) helps to eliminate out of band low frequency signals. Dc blocking capacitors (C2 and C3) are required for its input and output, to isolate the supply voltage from succeeding circuits. To improve input return loss, C1 is being use for external tuning. Toko Note : For L1, please refer to Figure 54 20 0 Phase (Degree) The external Inductor (L1), helps to stablize the attenuator performance (by gain flatness and change of phase) for the frequency of interest as well as improving its dynamic range. L1=27nH L1=Open -20 ALM-80210’s gain is adjusted by supplying a voltage thru Vctrl. For absolute dynamic range, Vctrl can operate from 0.8 to 5V, but for best linearity, Vctrl above 1V is recommended. -40 -60 -80 -100 0 10 20 Attenuation (dB) 30 40 Figure 54. Phase vs Attenuation with and without External L1 at 1900MHz 12 ALM-80210 Typical Scatter Parameters Tc = 25°C, Vdd = 5.0V, Vctrl = 5V, Vbias = 4.0V, Zo = 50Ω Freq GHz S11 Mag. Ang. dB Mag. Ang. dB Mag. Ang. dB Mag. Ang. dB 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.5 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0 1.0 0.9 0.9 0.9 0.9 0.8 0.8 0.8 0.7 0.7 0.6 0.6 0.5 0.5 0.4 0.4 0.4 0.4 0.3 0.3 0.3 0.2 0.2 0.2 0.1 0.1 0.0 0.1 0.1 0.2 0.3 0.2 0.3 0.7 0.7 0.3 0.7 0.9 0.8 0.8 0.7 0.7 0.6 0.6 0.5 0.4 0.3 0.1 173.2 167.3 162.3 157.2 151.8 146.1 140.3 134.8 129.5 124.0 118.5 114.5 110.7 106.8 103.1 98.9 94.6 90.0 84.8 79.1 72.7 65.3 57.1 46.2 31.4 5.3 -52.7 -107.7 -133.0 -148.7 163.0 128.4 -82.7 -128.5 -164.9 -158.9 173.3 149.3 144.2 137.6 116.8 96.2 85.0 78.2 69.0 52.2 21.3 -34.6 -0.3 -0.6 -0.8 -1.0 -1.2 -1.5 -1.9 -2.4 -3.0 -3.7 -4.4 -5.1 -5.7 -6.3 -7.0 -7.5 -8.2 -8.8 -9.5 -10.3 -11.2 -12.4 -13.9 -15.9 -18.8 -22.8 -26.1 -22.3 -18.1 -15.3 -10.5 -13.3 -9.8 -3.0 -3.1 -9.8 -2.5 -0.8 -1.9 -2.5 -3.4 -3.7 -3.9 -4.6 -5.6 -7.6 -11.2 -20.4 0.2 0.7 1.2 1.7 2.2 2.6 3.0 3.2 3.4 3.5 3.5 3.5 3.4 3.4 3.3 3.3 3.2 3.2 3.2 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.0 3.0 2.9 2.7 1.9 1.3 0.6 0.3 0.2 0.1 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 -57.1 -78.5 -99.5 -118.9 -137.1 -154.5 -171.4 172.7 157.5 143.4 130.3 118.3 107.2 96.9 87.0 77.7 68.6 59.9 51.0 42.3 33.5 24.4 15.4 5.8 -3.9 -14.3 -24.9 -35.7 -46.6 -57.4 -106.7 -147.2 130.4 111.6 31.6 -78.9 117.6 -6.6 -157.7 58.4 98.8 33.1 -26.7 -44.2 -86.2 -108.8 -40.8 -71.8 -14.1 -3.7 1.3 4.5 6.7 8.3 9.4 10.1 10.5 10.8 10.9 10.8 10.7 10.5 10.4 10.3 10.1 10.1 10.0 9.9 9.9 9.9 9.9 9.9 9.9 9.8 9.6 9.4 9.1 8.7 5.7 2.4 -4.4 -11.3 -14.6 -20.1 -38.8 -57.1 -60.1 -60.9 -62.4 -60.1 -54.0 -61.6 -58.6 -62.6 -60.3 -47.2 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.1 0.1 0.1 0.1 0.1 0.1 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 127.0 148.2 115.7 109.3 99.5 87.1 79.3 70.9 59.1 50.1 41.3 34.5 26.7 19.6 13.5 7.2 1.2 -5.1 -12.0 -17.7 -25.0 -30.8 -39.1 -46.0 -54.1 -63.0 -72.6 -81.5 -91.5 -101.4 -145.3 177.4 92.7 51.4 -63.3 -163.6 103.9 147.9 142.8 100.4 90.8 75.9 -21.8 -58.2 -65.1 -83.8 -37.8 -63.0 -56.6 -53.4 -47.2 -43.7 -41.5 -38.6 -37.0 -35.3 -34.2 -33.1 -32.4 -31.7 -31.1 -30.6 -30.2 -29.6 -29.3 -28.9 -28.4 -27.9 -27.4 -26.9 -26.5 -26.2 -25.7 -25.4 -25.1 -25.2 -25.0 -25.1 -26.8 -29.2 -35.1 -41.4 -39.0 -34.8 -42.1 -63.8 -50.3 -54.5 -54.5 -55.7 -53.0 -59.0 -56.5 -67.1 -66.4 -48.0 0.1 0.2 0.2 0.2 0.3 0.3 0.4 0.4 0.4 0.4 0.4 0.4 0.3 0.3 0.3 0.3 0.3 0.2 0.2 0.2 0.2 0.1 0.1 0.1 0.1 0.2 0.2 0.3 0.3 0.4 0.5 0.5 0.5 0.5 0.5 0.6 0.6 0.6 0.6 0.5 0.6 0.6 0.6 0.6 0.6 0.5 0.6 0.6 -71.6 -88.5 -100.9 -111.4 -120.6 -129.6 -138.8 -147.7 -156.1 -163.8 -171.1 -177.7 176.6 171.4 166.9 162.9 159.6 157.2 155.6 155.2 156.9 162.4 171.9 -173.8 -159.1 -150.2 -146.2 -146.1 -148.8 -152.6 -174.2 171.9 162.6 156.3 135.7 106.4 95.6 92.9 84.1 59.0 29.1 12.9 6.9 2.8 -9.2 -32.3 -53.9 -67.4 -71.6 -88.5 -100.9 -111.4 -120.6 -129.6 -138.8 -147.7 -156.1 -163.8 -171.1 -177.7 176.6 171.4 166.9 162.9 159.6 157.2 155.6 155.2 156.9 162.4 171.9 -173.8 -159.1 -150.2 -146.2 -146.1 -148.8 -152.6 -174.2 171.9 162.6 156.3 135.7 106.4 95.6 92.9 84.1 59.0 29.1 12.9 6.9 2.8 -9.2 -32.3 -53.9 -67.4 TRL Board Layer: 13 S21 Top Metal Rogers RO4350 Inner Metal Bottom Metal S12 → 0.5 oz CU → 0.01” → 0.5 oz CU → 0.5 oz CU S22 ALM-80210 K-Factor Tc = 25°C, Vdd = 5.0V, Vctrl = 5V, Vbias = 4.0V, Zo = 50Ω ALM-80210 Typical Noise Parameters Tc = 25°C, Vdd = 5.0V, Vctrl = 5V, Vbias = 4.0V, Zo = 50Ω Freq (GHz) FMIN (dB) Γopt Mag Ang Rn/Zo 50Ohm Ga (dB) 0.5 10.51 0.872 -152 2.52 6.99 1 5.89 0.728 -119 1.652 13.69 1.3 4.96 0.611 -92.7 1.43 12.09 1.5 4.64 0.478 -74.2 1.282 11.37 1.6 4.62 0.415 -64.7 1.22 11.03 1.7 4.66 0.352 -55.9 1.148 10.77 1.8 4.69 0.298 -45.7 1.088 10.52 1.9 4.75 0.238 -36.7 1.032 10.35 2 5.03 0.178 -25.9 1 10.21 2.1 5.21 0.125 -14.9 0.952 10.13 2.2 5.27 0.083 0.3 0.918 10.06 2.3 5.49 0.054 -25.9 0.862 10.06 2.4 5.63 0.043 98.9 0.818 9.93 2.5 5.79 0.061 130.4 0.812 9.89 2.6 5.93 0.097 156.4 0.748 9.83 2.7 6.21 0.107 163.3 0.798 9.78 2.8 6.38 0.134 170.5 0.792 9.7 2.9 6.61 0.172 -169.3 1.188 9.51 3 6.83 0.216 -161.7 0.828 9.26 3.5 7.64 0.21 -157.3 1.03 7.39 4 9.28 0.167 -146.5 1.87 4.14 4.5 10.95 0.033 77.2 3.28 0.69 5 13.86 0.272 88.4 7.552 -2.87 6 16.2 0.701 127.9 13.176 -6.91 14 PCB Layout and Stencil Design 0.675 0.400 0.475 0.500 0.360 0.300 0.360 0.400 0.200 1.100 3.270 4.800 0.400 0.500 2.287 0.900 0.360 0.300 1.500 3.070 4.600 2.088 0.900 3.270 4.800 2.870 4.600 PCB Land Pattern (Top View) Stencil Outline 0.400 0.400 0.360 0.400 0.360 4.600 4.800 4.600 4.800 Combined PCB & Stencil Layouts All Dimension are in MM 15 0.360 Package Dimension 0.940±0.10 5.000±0.10 PIN 1 ALM80210 5.000±0.10 WWYY XXXX 0.340 TOP VIEW SIDE VIEW 5.00 1.80 1.15 PIN 1 Orientation 0.10 0.17 2.20 0.09 0.40 0.13 0.07 2.20 0.10 0.14 2.29 0.55 0.90 0.50 BOTTOM VIEW Note : 1. All dimensions are in milimeters 2. Dimensions are inclusive of plating 3. Dimensions are exclusive of mold flash and metal burr. 16 Device Orientation REEL USER FEED DIRECTION CARRIER TAPE USER FEED DIRECTION Tape Dimensions 17 80210 WWYY XXYY 80210 WWYY XXYY TOP VIEW COVER TAPE 80210 WWYY XXYY END VIEW Part Ordering Information Part Number No. of Devices Container ALM-80210-BLKG 100 Antistatic Bag ALM-80210-TR1G 3000 13” Reel For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2014 Avago Technologies. All rights reserved. AV02-1971EN - August 28, 2014