Product
Folder
Order
Now
Support &
Community
Tools &
Software
Technical
Documents
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
2
bq24193 I C Controlled 4.5-A Single Cell USB/Adapter Charger
with Narrow VDC Power Path Management and USB OTG
1
1 Features
•
•
•
•
•
•
•
•
•
•
High Efficiency 4.5-A Switch Mode Charger
– 92% Charge Efficiency at 2 A, 90% at 4 A
– Accelerate Charge Time by Battery Path
Impedance Compensatioin
Highest Battery Discharge Efficiency with 12-mΩ
Battery Discharge MOSFET up to 9-A Discharge
Current
Single Input USB-compliant/Adapter Charger
– USB Host or Charging Port D+/D- Detection
Compatible to USB Battery Charger Spec 1.2
– Input Voltage and Current Limit Supports
USB2.0 and USB3.0
– Input Current Limit: 100 mA, 150 mA, 500 mA,
900 mA, 1.2 A, 1.5 A, 2 A and 3 A
3.9-V to 17-V Input Operating Voltage Range
– Support All Kinds of Adapter with Input Voltage
DPM Regulation
USB OTG 5 V at 1.3 A Synchronous Boost
Converter Operation
– 93% 5-V Boost Efficiency at 1 A
Narrow VDC (NVDC) Power Path Management
– Instant-on Works with No Battery or Deeply
Discharged Battery
– Ideal Diode Operation in Battery Supplement
Mode
1.5-MHz Switching Frequency for Low Profile
Inductor
Autonomous Battery Charging with or without
Host Management
– Battery Charge Enable
– Battery Charge Preconditioning
– Charge Termination and Recharge
High Accuracy (0°C to 125°C)
– ±0.5% Charge Voltage Regulation
– ±7% Charge Current Regulation
– ±7.5% Input Current Regulation
– ±2% Output Regulation in Boost Mode
High Integration
– Power Path Management
– Synchronous Switching MOSFETs
– Integrated Current Sensing
– Bootstrap Diode
– Internal Loop Compensation
•
•
•
•
Safety
– Battery Temperature Sensing and Charging
Safety Timer
– JEITA Guideline Compliant
– Thermal Regulation and Thermal Shutdown
– Input System Over-Voltage Protection
– MOSFET Over-Current Protection
Charge Status Outputs for LED or Host Processor
Low Battery Leakage Current and Support
Shipping Mode
4.00 mm x 4.00 mm QFN-24 Package
2 Applications
•
•
•
•
Tablet PC and Smart Phone
Portable Audio Speaker
Portable Media Players
Internet Devices
3 Description
The bq24193 is a highly-integrated switch-mode
battery charge management and system power path
management device for single cell Li-Ion and Lipolymer batteries in a wide range of tablet and other
portable devices.
Device Information(1)
PART NUMBER
bq24193
PACKAGE
BODY SIZE (NOM)
VQFN (24)
4.00 mm x 4.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
bq24193 with PSEL, USB On-The-Go (OTG) and
Support JEITA Profile
bq24193
12V Adapter
1μF
2.2μH
SYS: 3.5V-4.35V
SW
VBUS
PMID
47nF
10μF
10μF
10μF
BOOT
REGN
1μF
SYS
PGND
2.2kW
PG
STAT
VREF
10kW
Host
10kW
SYS
BAT
10μF
265W
(2A max)
10kW
SDA
SCL
INT
OTG
CE
PSEL
Power Pad
ILIM
REGN
2.27kW
TS1
TS2
6.86kW
10kW
(103-AT)
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Description (Continued) ........................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
5
7.1
7.2
7.3
7.4
7.5
7.6
5
5
6
6
6
9
Absolute Maximum Ratings ......................................
ESD Ratings ............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description ............................................ 12
8.1 Overview ................................................................. 12
8.2 Functional Block Diagram ....................................... 12
8.3 Feature Description................................................. 13
8.4 Device Functional Modes........................................ 25
8.5 Register Map........................................................... 26
9
Application and Implementation ........................ 34
9.1 Application Information............................................ 34
9.2 Typical Application .................................................. 34
10 Power Supply Recommendations ..................... 38
11 Layout................................................................... 38
11.1 Layout Guidelines ................................................. 38
11.2 Layout Example .................................................... 39
12 Device and Documentation Support ................. 40
12.1
12.2
12.3
12.4
12.5
12.6
Documentation Support .......................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
40
40
40
40
40
40
13 Mechanical, Packaging, and Orderable
Information ........................................................... 41
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (December 2014) to Revision A
Page
•
Changed VSLEEPZ MAX from 300 to 350 mV........................................................................................................................... 6
•
Changed VBAT_DPL_HY MAX from 230 mV to 260 mV .............................................................................................................. 7
•
Changed ICHG_20pct MAX from 125 to 135 mA......................................................................................................................... 7
•
Added ICHG_20pct at room temperature ..................................................................................................................................... 7
•
Changed VSHORT TYP from 1.8 to 2.0 V ................................................................................................................................. 7
•
Changed IADPT_DPM MIN from 1.4 to 1.35 A ............................................................................................................................ 8
•
Changed IADPT_DPM MAX from 1.6 to 1.65 A ........................................................................................................................... 8
•
Changed KILIM MIN from 440 to 435 A x Ω............................................................................................................................. 8
•
Changed VBTST_REFRESH, VBUS > 6 V TYP from 4.2 V to 4.5 V.............................................................................................. 8
•
Changed VREGN, VVBUS = 5 V, IREGN = 20 mA MAX ................................................................................................................ 9
•
Changed value from: 4.85 V to: 5 V ....................................................................................................................................... 9
2
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
5 Description (Continued)
Its low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time and
extends battery life during discharging phase. The I2C serial interface with charging and system settings makes
the device a truly flexible solution.
The device supports a wide range of input sources, including standard USB host port, USB charging port and
high power DC adapter. The bq24193 takes the result from detection circuit in the system, such as USB PHY
device. The bq24193 is compliant with USB 2.0 and USB 3.0 power spec with input current and voltage
regulation. Meanwhile, the bq24193 meets USB On-the-Go operation power rating specification by supplying 5 V
on VBUS with current limit up to 1.3 A.
The power path management regulates the system slightly above battery voltage but does not drop below 3.5-V
minimum system voltage (programmable). With this feature, the system maintains operation even when the
battery is completely depleted or removed. When the input current limit or voltage limit is reached, the power
path management automatically reduces the charge current to zero. As the system load continues to increase,
the power path discharges the battery until the system power requirement is met. This supplement mode
operation prevents overloading the input source.
The device initiates and completes a charging cycle without software control. It automatically detects the battery
voltage and charges the battery in three phases: pre-conditioning, constant current and constant voltage. At the
end of the charging cycle, the charger automatically terminates when the charge current is below a preset limit in
the constant voltage phase. When the full battery falls below the recharge threshold, the charger will
automatically start another charging cycle.
The device provide various safety features for battery charging and system operation, including dual pack
negative thermistor monitoring, charging safety timer and over-voltage/over-current protections. The bq24193
also supports JEITA guideline compliant temperature profile. The thermal regulation reduces charge current
when the junction temperature exceeds 120°C (programmable).
The STAT output reports the charging status and any fault conditions. The PG output in the bq24193 indicates if
a good power source is present.The INT immediately notifies the host when a fault occurs.
The bq24193 is available in a 24-pin, 4.00 x 4.00 mm2 thin VQFN package.
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
3
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
6 Pin Configuration and Functions
VBUS
PMID
REGN
BTST
SW
SW
RGE Package
24-Pin VQFN With Exposed Thermal Pad
(Top View)
24
23
22
21
20
19
VBUS
1
18
PGND
PSEL
2
17
PGND
16
SYS
PG
3
bq24193
14
BAT
SDA
6
13
BAT
7
8
9
10
11
12
TS2
5
TS1
SCL
ILIM
SYS
CE
15
OTG
4
INT
STAT
Pin Functions
PIN
TYPE
DESCRIPTION
1,24
P
Charger Input Voltage. The internal n-channel reverse block MOSFET (RBFET) is connected between VBUS and PMID
with VBUS on source. Place a 1-µF ceramic capacitor from VBUS to PGND and place it as close as possible to IC. (Refer
to Application Information Section for details)
PSEL
2
I
Digital
Power source selection input. High indicates a USB host source and Low indicates an adapter source.
PG
3
O
Digital
Open drain active low power good indicator. Connect to the pull up rail via 10-kΩ resistor. LOW indicates a good input
source if the input voltage is between UVLO and ACOV, above SLEEP mode threshold, and current limit is above 30 mA.
STAT
4
O
Digital
Open drain charge status output to indicate various charger operation. Connect to the pull up rail via 10-kΩ. LOW
indicates charge in progress. HIGH indicates charge complete or charge disabled. When any fault condition occurs, STAT
pin blinks at 1 Hz.
SCL
5
I
Digital
I2C Interface clock. Connect SCL to the logic rail through a 10-kΩ resistor.
SDA
6
I/O
Digital
I2C Interface data. Connect SDA to the logic rail through a 10-kΩ resistor.
INT
7
O
Digital
Open-drain Interrupt Output. Connect the INT to a logic rail via 10-kΩ resistor. The INT pin sends active low, 256-us pulse
to host to report charger device status and fault.
8
I
Digital
CE
9
I
Digital
Active low Charge Enable pin. Battery charging is enabled when REG01[5:4] = 01 and CE pin = Low. CE pin must be
pulled high or low.
ILIM
10
I
Analog
ILIM pin sets the maximum input current limit by regulating the ILIM voltage at 1 V. A resistor is connected from ILIM pin to
ground to set the maximum limit as IINMAX = (1V/RILIM) × 530. The actual input current limit is the lower one set by ILIM
and by I2C REG00[2:0]. The minimum input current programmed on ILIM pin is 500 mA.
TS1
11
I
Analog
Temperature qualification voltage input #1. Connect a negative temperature coefficient thermistor. Program temperature
window with a resistor divider from REGN to TS1 to GND. Charge suspends when either TS pin is out of range.
Recommend 103AT-2 thermistor. TS1 and TS2 pins have to be shorted together in bq24193.
TS2
12
I
Analog
Temperature qualification voltage input #2. Connect a negative temperature coefficient thermistor. Program temperature
window with a resistor divider from REGN to TS2 to GND. Charge suspends when either TS pin is out of range.
Recommend 103AT-2 thermistor. TS1 and TS2 pins have to be connected together in bq24193.
NAME
NUMBER
VBUS
USB current limit selection pin during buck mode, and active high enable pin during boost mode.
OTG
In buck mode with USB host (PSEL=High), when OTG = High, IIN limit = 500 mA and when OTG = Low, IIN limit = 100
mA.
The boost mode is activated when the REG01[5:4] = 10 and OTG pin is High.
4
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
Pin Functions (continued)
PIN
TYPE
DESCRIPTION
NAME
NUMBER
BAT
13,14
P
Battery connection point to the positive terminal of the battery pack. The internal BATFET is connected between BAT and
SYS. Connect a 10 µF closely to the BAT pin.
SYS
15,16
P
System connection point. The internal BATFET is connected between BAT and SYS. When the battery falls below the
minimum system voltage, switch-mode converter keeps SYS above the minimum system voltage. (Refer to Application
Information Section for inductor and capacitor selection.)
PGND
17,18
P
Power ground connection for high-current power converter node. Internally, PGND is connected to the source of the nchannel LSFET. On PCB layout, connect directly to ground connection of input and output capacitors of the charger. A
single point connection is recommended between power PGND and the analog GND near the IC PGND pin.
SW
19,20
O
Analog
Switching node connecting to output inductor. Internally SW is connected to the source of the n-channel HSFET and the
drain of the n-channel LSFET. Connect the 0.047-µF bootstrap capacitor from SW to BTST.
BTST
21
P
PWM high side driver positive supply. Internally, the BTST is connected to the anode of the boost-strap diode. Connect
the 0.047-µF bootstrap capacitor from SW to BTST.
REGN
22
P
PWM low side driver positive supply output. Internally, REGN is connected to the cathode of the boost-strap diode.
Connect a 4.7-µF (10-V rating) ceramic capacitor from REGN to analog GND. The capacitor should be placed close to the
IC. REGN also serves as bias rail of TS1 and TS2 pins.
PMID
23
O
Analog
Connected to the drain of the reverse blocking MOSFET and the drain of HSFET. Given the total input capacitance,
connect a 1-µF capacitor on VBUS to PGND, and the rest all on PMID to PGND. (Refer to Application Information Section
for details)
Thermal
Pad
–
P
Exposed pad beneath the IC for heat dissipation. Always solder thermal pad to the board, and have vias on the thermal
pad plane star-connecting to PGND and ground plane for high-current power converter.
7 Specifications
7.1 Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
Voltage range (with
respect to GND)
Output sink current
MIN
MAX
UNIT
VBUS
–2
22
V
PMID
–0.3
22
V
STAT, PG
–0.3
20
V
BTST
–0.3
26
V
SW
–2
20
V
BAT, SYS (converter not switching)
–0.3
6
V
SDA, SCL, INT, OTG, ILIM, REGN, TS1, TS2, CE, PSEL
–0.3
7
V
BTST TO SW
–0.3
–7
V
PGND to GND
–0.3
–0.3
V
6
mA
–40°C
150
°C
–65
150
°C
INT, STAT, PG
Junction temperature
Storage temperature, Tstg
(1)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage
values are with respect to the network ground terminal unless otherwise noted.
7.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
1000
Charged device model (CDM), per JEDEC specification JESD22C101 (2)
250
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
5
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
7.3 Recommended Operating Conditions
MIN
MAX
UNIT
3.9
17 (1)
V
3
A
Output current (SYS)
4.5
A
Battery voltage
4.4
V
Fast charging current
4.5
A
6 (continuous)
9 (peak)
(up to 1 sec duration)
A
85
°C
VIN
Input voltage
IIN
Input current
ISYS
VBAT
IBAT
Discharging current with internal MOSFET
TA
(1)
Operating free-air temperature range
–40
The inherent switching noise voltage spikes should not exceed the absolute maximum rating on either the BTST or SW pins. A tight
layout minimizes switching noise.
7.4 Thermal Information
bq24193
THERMAL METRIC (1)
RθJA
Junction-to-ambient thermal resistance
32.2
RθJCtop
Junction-to-case (top) thermal resistance
29.8
RθJB
Junction-to-board thermal resistance
9.1
ψJT
Junction-to-top characterization parameter
0.3
ψJB
Junction-to-board characterization parameter
9.1
RθJCbot
Junction-to-case (bottom) thermal resistance
2.2
(1)
UNIT
RGE (24 PIN)
°C/W
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report (SPRA953).
7.5 Electrical Characteristics
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values unless other
noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
QUIESCENT CURRENTS
VVBUS < VUVLO, VBAT = 4.2 V,
leakage between BAT and VBUS
IBAT
Battery discharge current (BAT, SW, SYS)
IVBUS
Input supply current (VBUS)
IOTGBOOST
Battery discharge current in boost mode
5
µA
High-Z Mode, or no VBUS, BATFET
disabled (REG07[5] = 1),
12
20
µA
High-Z Mode, or no VBUS, REG07[5]
= 0, –40°C to 85°C
32
55
µA
VVBUS = 5 V, High-Z mode
15
30
µA
VVBUS = 17 V, High-Z mode
30
50
µA
VVBUS > VUVLO, VVBUS > VBAT,
converter not switching
1.5
3
mA
VVBUS > VUVLO, VVBUS > VBAT,
converter switching, VBAT = 3.2 V, ISYS
=0A
4
mA
VVBUS > VUVLO, VVBUS > VBAT,
converter switching, VBAT = 3.8 V, ISYS
=0A
15
mA
VBAT = 4.2 V, Boost mode, IVBUS = 0
A, converter switching
4
mA
VBUS/BAT POWER UP
VVBUS_OP
VBUS operating range
2
3.9
17
V
VVBUS_UVLOZ
VBUS for active I C, no battery
VVBUS rising
3.6
VSLEEP
Sleep mode falling threshold
VVBUS falling, VVBUS-VBAT
35
80
120
mV
VSLEEPZ
Sleep mode rising threshold
VVBUS rising, VVBUS-VBAT
170
250
350
mV
VACOV
VBUS over-voltage rising threshold
VVBUS rising
17.4
18
6
Submit Documentation Feedback
V
V
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
Electrical Characteristics (continued)
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values unless other
noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
700
UNIT
VACOV_HYST
VBUS over-voltage falling hysteresis
VVBUS falling
VBAT_UVLOZ
Battery for active I2C, no VBUS
VBAT rising
mV
VBAT_DPL
Battery depletion threshold
VBAT falling
2.4
2.6
V
VBAT_DPL_HY
Battery depletion rising hysteresis
VBAT rising
170
260
mV
VVBUSMIN
Bad adapter detection threshold
VVBUS falling
3.8
V
IBADSRC
Bad adapter detection current source
30
mA
tBADSRC
Bad source detection duration
30
ms
2.3
V
POWER PATH MANAGEMENT
VSYS_RANGE
Typical system regulation voltage
Isys = 0 A, Q4 off, VBAT up to 4.2 V,
REG01[3:1] = 101, VSYSMIN = 3.5 V
3.5
VSYS_MIN
System voltage output
REG01[3:1] = 101, VSYSMIN = 3.5 V
3.55
RON(RBFET)
Internal top reverse blocking MOSFET onresistance
Measured between VBUS and PMID
23
38
RON(HSFET)
Internal top switching MOSFET on-resistance
between PMID and SW
TJ = –40°C to 85°C
27
35
TJ = -40°C to 125°C
27
45
RON(LSFET)
Internal bottom switching MOSFET on-resistance
between SW and PGND
TJ = –40°C to 85°C
32
45
TJ = -40°C to 125°C
32
48
VFWD
BATFET forward voltage in supplement mode
BAT discharge current 10 mA
30
VSYS_BAT
SYS/BAT Comparator
VSYS falling
90
VBATGD
Battery good comparator rising threshold
VBAT rising
VBATGD_HYST
Battery good comparator falling threshold
VBAT falling
3.4
4.35
3.65
3.55
V
V
mΩ
mΩ
mΩ
mV
mV
3.7
100
V
mV
BATTERY CHARGER
VBAT_REG_ACC
IICHG_REG_ACC
Charge voltage regulation accuracy
Fast charge current regulation accuracy
VBAT = 4.112 V and 4.208 V
–0.5%
0.5%
VBAT = 3.8 V, ICHG = 1792 mA, TJ =
25°C
–4%
4%
VBAT = 3.8 V, ICHG = 1792 mA, TJ =
–20°C to 125°C
–7%
7%
ICHG_20pct
Charge current with 20% option on
VBAT = 3.1 V, ICHG = 104 mA, REG02
= 03
ICHG_20pct
Charge current with 20% option on
VBAT = 3.1 V, ICHG = 104 mA, REG02
= 03, at room temperature
VBATLOWV
Battery LOWV falling threshold
Fast charge to precharge, REG04[1] =
1
2.6
VBATLOWV_HYST
Battery LOWV rising threshold
Precharge to fast charge, REG04[1] =
1
2.8
IPRECHG_ACC
Precharge current regulation accuracy
VBAT = 2.6 V, ICHG = 256 mA
–20%
ITERM_ACC
Termination current accuracy
ITERM = 256 mA, ICHG = 960 mA
–20%
VSHORT
Battery Short Voltage
VBAT falling
2.0
V
VSHORT_HYST
Battery Short Voltage hysteresis
VBAT rising
200
mV
ISHORT
Battery short current
VBAT < 2.2V
100
mA
VRECHG
Recharge threshold below VBAT_REG
VBAT falling, REG04[0] = 0
100
mV
tRECHG
Recharge deglitch time
VBAT falling, REG04[0] = 0
20
TJ = 25°C
12
15
TJ = –40°C to 125°C
12
20
RON_BATFET
SYS-BAT MOSFET on-resistance
75
100
135
mA
130
mA
2.8
2.9
V
3.0
3.1
V
20%
20%
ms
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
mΩ
7
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
Electrical Characteristics (continued)
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values unless other
noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INPUT VOLTAGE/CURRENT REGULATION
VINDPM_REG_ACC
Input voltage regulation accuracy
USB Input current regulation limit, VBUS = 5 V,
current pulled from SW
IUSB_DPM
–2%
2%
USB100
85
100
mA
USB150
125
150
mA
USB500
440
500
mA
USB900
750
900
mA
1.35
IADPT_DPM
Input current regulation accuracy
Input current limit 1.5 A
IIN_START
Input current limit during system start up
VSYS < 2.2 V
KILIM
IIN = KILIM/RILIM
IINDPM = 1.5 A
1.5
1.65
100
435
485
A
mA
530
AxΩ
BAT OVER-VOLTAGE PROTECTION
VBATOVP
Battery over-voltage threshold
VBAT rising, as percentage of VBAT_REG
VBATOVP_HYST
Battery over-voltage hysteresis
VBAT falling, as percentage of
VBAT_REG
tBATOVP
Battery over-voltage deglitch time to disable charge
104%
2%
1
µs
THERMAL REGULATION AND THERMAL SHUTDOWN
TJunction_REG
Junction temperature regulation accuracy
REG06[1:0] = 11
TSHUT
Thermal shutdown rising temperature
Temperature increasing
TSHUT_HYS
Thermal shutdown hysteresis
115 (1)
120
125 (1)
160
°C
°C
30
°C
Thermal shutdown rising deglitch
Temperature increasing delay
1
ms
Thermal shutdown falling deglitch
Temperature decreasing delay
1
ms
JEITA THERMISTER COMPARATOR (bq24193)
VT1
T1 (0°C) threshold, Charge suspended T1 below
this temperature.
VTS rising, As percentage to VREGN
VT1_HYS
Charge back to ICHG/2 and 4.2 V above this
temperature
Hysteresis, VTS falling
VT2
T2 (10°C) threshold, Charge back to ICHG/2 and 4.2
VTS rising, as percentage of VREGN
V below this temperature
VT2_HYS
Charge back to ICHG and 4.2 V above this
temperature
Hysteresis, VTS falling
VT3
T3 (45°C) threshold, Charge back to ICHG and 4.05
V above this temperature
VTS falling, as percentage of VREGN
VT3_HYS
Charge back to ICHG and 4.2 V below this
temperature
Hysteresis, VTS rising
VT5
T5 (60°C) threshold, charge suspended above this
temperature
VTS falling, as percentage of VREGN
VT5_HYS
Charge back to ICHG and 4.05 V below this
temperature
Hysteresis, VTS rising
70.2%
70.8%
71.4%
0.6%
68.0%
68.6%
69.2%
0.8%
55.5%
56.1%
56.7%
0.8%
47.6%
48.1%
48.6%
1.2%
CHARGE OVER-CURRENT COMPARATOR
IHSFET_OCP
HSFET over-current threshold
IBATFET_OCP
System over load threshold
5.3
7
A
9
A
CHARGE UNDER-CURRENT COMPARATOR (CYCLE-BY-CYCLE)
VLSFET_UCP
LSFET charge under-current falling threshold
From sync mode to non-sync mode
100
mA
PWM OPERATION
FSW
PWM Switching frequency, and digital clock
DMAX
Maximum PWM duty cycle
VBTST_REFRESH
Bootstrap refresh comparator threshold
1300
1500
1700
kHz
97%
VBTST-VSW when LSFET refresh
pulse is requested, VBUS = 5 V
3.6
VBTST-VSW when LSFET refresh
pulse is requested, VBUS > 6 V
4.5
V
BOOST MODE OPERATION
VOTG_REG
OTG output voltage
I(VBUS) = 0
VOTG_REG_ACC
OTG output voltage accuracy
I(VBUS) = 0
(1)
8
5.00
–2%
V
2%
Not production tested
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
Electrical Characteristics (continued)
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values unless other
noted.
PARAMETER
IOTG
OTG mode output current
IOTG_HSZCP
HSFET under current falling threshold
IRBFET_OCP
RBFET over-current threshold
TEST CONDITIONS
MIN
REG01[0] = 0
0.5
REG01[0] = 1
1.3
TYP
MAX
UNIT
A
A
100
mA
REG01[0] = 1
1.4
1.8
2.7
REG01[0] = 0
0.6
1.1
1.8
A
REGN LDO
VREGN
REGN LDO output voltage
IREGN
REGN LDO current limit
VVBUS = 10 V, IREGN = 40 mA
5.6
6
6.4
VVBUS = 5 V, IREGN = 20 mA
4.75
4.8
5
VVBUS = 10 V, VREGN = 3.8 V
50
V
V
mA
LOGIC I/O PIN CHARACTERISTICS (OTG, CE, PSEL, STAT, PG)
VILO
Input low threshold
VIH
Input high threshold
0.4
VOUT_LO
Output low saturation voltage
Sink current = 5 mA
IBIAS
High level leakage current
Pull up rail 1.8 V
1.3
V
V
0.4
V
1
µA
I2C INTERFACE (SDA, SCL, INT)
VIH
Input high threshold level
VPULL-UP = 1.8 V, SDA and SCL
VIL
Input low threshold level
VPULL-UP = 1.8 V, SDA and SCL
1.3
0.4
V
VOL
Output low threshold level
Sink current = 5 mA
0.4
V
IBIAS
High-level leakage current
VPULL-UP = 1.8 V, SDA and SCL
1
µA
fSCL
SCL clock frequency
400
kHz
V
DIGITAL CLOCK AND WATCHDOG TIMER
fHIZ
Digital crude clock
REGN LDO disabled
15
35
50
kHz
fDIG
Digital clock
REGN LDO enabled
1300
1500
1700
kHz
tWDT
REG05[5:4] = 11
REGN LDO enabled
136
160
sec
7.6 Typical Characteristics
Table 1. Table of Figures
FIGURE NUMBER
System Light Load Efficiency vs System Load Current
Figure 1
SYS Voltage Regulation vs System Load
Figure 2
Charging Efficiency vs Charging Current
Figure 3
Boost Mode Efficiency vs VBUS Load Current
Figure 4
Boost Mode VBUS Voltage Regulation vs VBUS Load Current
Figure 5
SYS Voltage vs Temperature
Figure 6
BAT Voltage vs Temperature
Figure 7
Input Current Limit vs temperature
Figure 8
Charge Current vs temperature
Figure 9
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
9
bq24193
www.ti.com
95
3.70
90
3.68
SYS Voltage (V)
Efficiency (%)
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
85
80
75
3.66
3.64
3.62
VBUS = 5 V
VBUS = 5 V
VBUS = 17 V
VBUS = 9 V
3.60
70
0
100
200
300
400
500
Load Current (mA)
0
600
2
95
4
5
C014
Figure 2. SYS Voltage Regulation vs System Load
100
VBUS = 5 V
VBUS = 7 V
VBUS = 9 V
VBUS = 12 V
VBAT = 3.2 V
VBAT = 3.8 V
95
Efficiency (%)
93
3
System Load Current (A)
Figure 1. System Light Load Efficiency vs System Load
Current
Efficiency (%)
1
C012
91
89
90
85
87
80
85
0
1
2
3
4
Load Current (A)
0
5
500
1000
1500
VBUS Load Current (A)
C011
Figure 3. Charging Efficiency vs Charging Current
C013
Figure 4. Boost Mode Efficiency vs VBUS Load Current
5.04
3.80
5.02
3.75
5.00
SYS Voltage (V)
VBUS Voltage (V)
SYSMIN 3.5 V
4.98
4.96
4.94
3.70
3.65
3.60
VBAT = 3.2 V
4.92
3.55
VBAT = 3.8 V
VBAT = 4.2 V
4.90
0
200
400
3.50
600
800
1000
VBUS Load Current (A)
1200
1400
±50
C005
Figure 5. Boost Mode VBUS Voltage Regulation vs VBUS
Load Current
10
Submit Documentation Feedback
0
50
100
Temperature (ƒC)
150
C001
Figure 6. SYS Voltage vs Temperature
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
2000
4.25
1800
Input Current Limit (A)
BAT Voltage (V)
4.21
4.17
4.13
4.09
VREG = 4.112 V
1600
1400
1200
1000
IIN = 500 mA
800
IIN = 1.5 A
600
IIN = 2 A
VREG = 4.208 V
400
4.05
–50
0
50
100
±50
150
Temperature (°C)
0
50
100
Temperature (ƒC)
C002
Figure 7. BAT Voltage vs Temperature
150
C003
Figure 8. Input Current Limit vs Temperature
5
4.5
Charge Current (A)
4
3.5
3
2.5
2
1.5
1
TREG 80 C
TREG 120 C
0.5
0
40
50
60
70
80
90
100
110
120
Temperature (°C)
130
C009
Figure 9. Charge Current vs Temperature
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
11
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
8 Detailed Description
8.1 Overview
The bq24193 is an I2C controlled power path management device and a single cell Li-Ion battery charger. It
integrates the input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side
switching FET (LSFET, Q3), and BATFET (Q4) between system and battery. The device also integrates the
bootstrap diode for the high-side gate drive.
8.2 Functional Block Diagram
VBUS
PMID
Q1
V(VBUS_UVLOZ)
UVLO
Q1 Gate
Control
V(BATZ)+V(SLEEP)
SLEEP
REGN
REGN
LDO
EN_HIZ
ACOV
V(ACOV)
BTST
FBO
VBUS
V(OTG_OVP)
VBUS_OVP_BOOST
VINDPM
I(Q2)
I(OTG_HSZCP)
Q2_UCP_BOOST
I(Q3)
I(OTG_ILIM)
Q3_OCP_BOOST
IINDPM
SW
BAT
V(BAT_REG) x V(BATOVP)
IC TJ
CONVERTER
CONTROL
BATOVP
Q2
REGN
BAT
TREG
VBAT_REG I(LSFET_UCP)
Q3
UCP
I(Q3)
SYS
Q2_OCP
I(Q2)
I(HSFET_OCP)
REFRESH
V(BTST-SW)
V(BTST_REFRESH)
PGND
VSYSMIN
ICHG_REG
EN_HIZ
EN_CHARGE
EN_BOOST
SYS
ICHG
VBAT_REG
ICHG_REG
REF
DAC
I(BADSRC)
BAD_SRC
CONVERTER
CONTROL
TSHUT
STATE
MACHINE
ILIM
PSEL
USB
Adapter
1.5A
BAT_GD
OTG
BAT
BAT
V(BATGD)
V(BAT_REG)-V(RECHG)
BAT
INT
ICHG
ITERM
TERMINATION
STAT
PG
I2C
Interface
SCL
12
SDA
BATSHORT
Q4
IDC
IC TJ
TSHUT
RECHRG
CHARGE
CONTROL
SUSPEND
STATE
MACHINE BATLOWV
Q4 Gate
Control
V(BATLOWV)
BAT
BATTERY
THERMISTER
SENSING
TS1
TS2
V(SHORT)
BAT
CE
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
8.3 Feature Description
8.3.1 Device Power Up
8.3.1.1 Power-On-Reset (POR)
The internal bias circuits are powered from the higher voltage of VBUS and BAT. When VBUS or VBAT rises
above UVLOZ, the sleep comparator, battery depletion comparator and BATFET driver are active. I2C interface
is ready for communication and all the registers are reset to default value. The host can access all the registers
after POR.
8.3.1.2 Power Up from Battery without DC Source
If only battery is present and the voltage is above depletion threshold (VBAT_DEPL), the BATFET turns on and
connects battery to system. The REGN LDO stays off to minimize the quiescent current. The low RDSON in
BATFET and the low quiescent current on BAT minimize the conduction loss and maximize the battery run time.
The device always monitors the discharge current through BATFET. When the system is overloaded or shorted,
the device will immediately turn off BATFET and keep BATFET off until the input source plugs in again.
8.3.1.2.1 BATFET Turn Off
The BATFET can be forced off by the host through I2C REG07[5]. This bit allows the user to independently turn
off the BATFET when the battery condition becomes abnormal during charging. When BATFET is off, there is no
path to charge or discharge the battery.
When battery is not attached, the BATFET should be turned off by setting REG07[5] to 1 to disable charging and
supplement mode.
8.3.1.2.2 Shipping Mode
When end equipment is assembled, the system is connected to battery through BATFET. There will be a small
leakage current to discharge the battery even when the system is powered off. In order to extend the battery life
during shipping and storage, the device can turn off BATFET so that the system voltage is zero to minimize the
leakage.
In order to keep BATFET off during shipping mode, the host has to disable the watchdog timer (REG05[5:4] =
00) and disable BATFET (REG07[5] = 1) at the same time.
Once the BATFET is disabled, the BATFET can be turned on by plugging in adapter.
8.3.1.3 Power Up from DC Source
When the DC source plugs in, the bq24193 checks the input source voltage to turn on REGN LDO and all the
bias circuits. It also checks the input current limit before starts the buck converter.
8.3.1.3.1 REGN LDO
The REGN LDO supplies internal bias circuits as well as the HSFET and LSFET gate drive. The LDO also
provides bias rail to TS1/TS2 external resistors. The pull-up rail of STAT can be connected to REGN as well.
The REGN is enabled when all the conditions are valid.
1. VBUS above UVLOZ
2. VBUS above battery + VSLEEPZ in buck mode or VBUS below battery + VSLEEPZ in boost mode
3. After typical 220ms delay (100ms minimum) is complete
If one of the above conditions is not valid, the device is in high impedance mode (HIZ) with REGN LDO off. The
device draws less than 50 µA from VBUS during HIZ state. The battery powers up the system when the device is
in HIZ.
8.3.1.3.2 Input Source Qualification
After REGN LDO powers up, the bq24193 checks the current capability of the input source. The input source has
to meet the following requirements to start the buck converter.
1. VBUS voltage below 18 V (not in ACOV)
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
13
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
Feature Description (continued)
2. VBUS voltage above 3.8 V when pulling 30 mA (poor source detection)
Once the input source passes all the conditions above, the status register REG08[2] goes high and the PG pin
goes low. An INT is asserted to the host.
If the device fails the poor source detection, it will repeat the detection every 2 seconds.
8.3.1.3.3 Input Current Limit Detection
The USB ports on personal computers are convenient charging source for portable devices (PDs). If the portable
device is attached to a USB host, the USB specification requires the portable device to draw limited current (100
mA/500 mA in USB 2.0, and 150 mA/900 mA in USB 3.0). If the portable device is attached to a charging port, it
is allowed to draw up to 1.5 A.
After the PG is LOW or REG08[2] goes HIGH, the charger device always runs input current limit detection when
a DC source plugs in unless the charger is in HIZ during host mode.
The bq24193 sets input current limit through PSEL and OTG pins.
After the input current limit detection is done, the host can write to REG00[2:0] to change the input current limit.
8.3.1.3.4 PSEL/OTG Pins Set Input Current Limit
The bq24193 has PSEL. It directly takes the USB PHY device output to decide whether the input is USB host or
charging port.
Table 2. bq24193 Input Current Limit Detection
PSEL
OTG
INPUT CURRENT LIMIT
REG08[7:6]
HIGH
LOW
100 mA
01
HIGH
HIGH
500 mA
01
LOW
—
3A
10
8.3.1.3.5 HIZ State wth 100mA USB Host
In battery charging spec, the good battery threshold is the minimum charge level of a battery to power up the
portable device successfully. When the input source is 100-mA USB host, and the battery is above bat-good
threshold (VBATGD), the device follows battery charging spec and enters high impedance state (HIZ). In HIZ state,
the device is in the lowest quiescent state with REGN LDO and the bias circuits off. The charger device sets
REG00[7] to 1, and the VBUS current during HIZ state will be less than 30 µA. The system is supplied by the
battery.
Once the charger device enters HIZ state in host mode, it stays in HIZ until the host writes REG00[7] = 0. When
the processor host wakes up, it is recommended to first check if the charger is in HIZ state.
In default mode, the charger IC will reset REG00[7] back to 0 when input source is removed. When another
source plugs in, the charger IC will run detection again, and update the input current limit.
8.3.1.3.6 Force Input Current Limit Detection
The host can force the charger device to run input current limit detection by setting REG07[7] = 1. After the
detection is complete, REG07[7] will return to 0 by itself.
8.3.1.4 Converter Power-Up
After the input current limit is set, the converter is enabled and the HSFET and LSFET start switching. If battery
charging is disabled, BATFET turns off. Otherwise, BATFET stays on to charge the battery.
The bq24193 provides soft-start when ramp up the system rail. When the system rail is below 2.2 V, the input
current limit is forced to 100 mA. After the system rises above 2.2 V, the charger device sets the input current
limit set by the lower value between register and ILIM pin.
As a battery charger, the bq24193 deploys a 1.5-MHz step-down switching regulator. The fixed frequency
oscillator keeps tight control of the switching frequency under all conditions of input voltage, battery voltage,
charge current and temperature, simplifying output filter design.
14
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
A type III compensation network allows using ceramic capacitors at the output of the converter. An internal sawtooth ramp is compared to the internal error control signal to vary the duty cycle of the converter. The ramp
height is proportional to the PMID voltage to cancel out any loop gain variation due to a change in input voltage.
In order to improve light-load efficiency, the device switches to PFM control at light load when battery is below
minimum system voltage setting or charging is disabled. During the PFM operation, the switching duty cycle is
set by the ratio of SYS and VBUS.
8.3.1.5 Boost Mode Operation from Battery
The bq24193 supports boost converter operation to deliver power from the battery to other portable devices
through USB port. The boost mode output current rating meets the USB On-The-Go 500-mA output requirement.
The maximum output current is 1.3 A. The boost operation can be enabled if the following conditions are valid:
1. BAT above BATLOWV threshold (VBATLOWV set by REG04[1])
2. VBUS less than BAT+VSLEEP (in sleep mode)
3. Boost mode operation is enabled (OTG pin HIGH and REG01[5:4] = 10)
4. After 220-ms delay from boost mode enable
In boost mode, the bq24193 employs a 1.5-MHz step-up switching regulator. Similar to buck operation, the
device switches from PWM operation to PFM operation at light load to improve efficiency.
During boost mode, the status register REG08[7:6] is set to 11, the VBUS output is 5 V and the output current
can reach up to 500 mA or 1.3 A, selected via I2C (REG01[0]).
Any fault during boost operation, including VBUS over-voltage or over-current, sets the fault register REG09[6] to
1 and an INT is asserted.
8.3.2 Power Path Management
The bq24193 accommodates a wide range of input sources from USB, wall adapter, to car battery. The device
provides automatic power path selection to supply the system (SYS) from input source (VBUS), battery (BAT), or
both.
8.3.2.1 Narrow VDC Architecture
The device deploys Narrow VDC architecture (NVDC) with BATFET separating system from battery. The
minimum system voltage is set by REG01[3:1]. Even with a fully depleted battery, the system is regulated above
the minimum system voltage (default 3.5 V).
When the battery is below minimum system voltage setting, the BATFET operates in linear mode (LDO mode),
and the system is 150 mV above the minimum system voltage setting. As the battery voltage rises above the
minimum system voltage, BATFET is fully on and the voltage difference between the system and battery is the
VDS of BATFET.
When the battery charging is disabled or terminated, the system is always regulated at 150 mV above the
minimum system voltage setting. The status register REG08[0] goes high when the system is in minimum system
voltage regulation.
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
15
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
4.5
4.3
Charge Enabled
4.1
SYS
(V)
Charge Disabled
3.9
3.7
3.5
Minimum System Voltage
3.3
3.1
2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3
BAT (V)
Figure 10. V(SYS) vs V(BAT)
8.3.2.2 Dynamic Power Management
To meet maximum current limit in USB spec and avoid over loading the adapter, the bq24193 features Dynamic
Power Management (DPM), which continuously monitors the input current and input voltage.
When input source is over-loaded, either the current exceeds the input current limit (REG00[2:0]) or the voltage
falls below the input voltage limit (REG00[6:3]). The device then reduces the charge current until the input current
falls below the input current limit and the input voltage rises above the input voltage limit.
When the charge current is reduced to zero, but the input source is still overloaded, the system voltage starts to
drop. Once the system voltage falls below the battery voltage, the device automatically enters the supplement
mode where the BATFET turns on and battery starts discharging so that the system is supported from both the
input source and battery.
During DPM mode (either VINDPM or IINDPM), the status register REG08[3] will go high.
Figure 11 shows the DPM response with 9-V/1.2-A adapter, 3.2-V battery, 2.8-A charge current and 3.4-V
minimum system voltage setting.
Voltage
VBUS
9V
SYS
3.6V
3.4V
3.2V
3.18V
BAT
Current
4A
ICHG
3.2A
2.8A
ISYS
1.2A
1.0A
0.5A
IIN
-0.6A
DPM
DPM
Supplement
Figure 11. DPM Response
16
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
8.3.2.3 Supplement Mode
When the system voltage falls below the battery voltage, the BATFET turns on and the BATFET gate is
regulated the gate drive of BATFET so that the minimum BATFET VDS stays at 30 mV when the current is low.
This prevents oscillation from entering and exiting the supplement mode. As the discharge current increases, the
BATFET gate is regulated with a higher voltage to reduce RDSON until the BATFET is in full conduction. At this
point onwards, the BATFET VDS linearly increases with discharge current. Figure 12 shows the V-I curve of the
BATFET gate regulation operation. BATFET turns off to exit supplement mode when the battery is below battery
depletion threshold.
4.5
4.0
CURRENT (A)
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
0
5
10
15
20
25
30
35
40
45
50
55
V(BAT-SYS) (mV)
Figure 12. BATFET V-I Curve
8.3.3 Battery Charging Management
The bq24193 charges 1-cell Li-Ion battery with up to 4.5A charge current for high capacity tablet battery. The 12mΩ BATFET improves charging efficiency and minimizes the voltage drop during discharging.
8.3.3.1 Autonomous Charging Cycle
With battery charging enabled at POR (REG01[5:4] = 01), the bq24193 can complete a charging cycle without
host involvement. The device default charging parameters are listed in .
Table 3. Charging Parameter Default Setting
A
•
•
•
•
•
DEFAULT MODE
bq24193
Charging voltage
4.208 V
Charging current
2.048 A
Pre-charge current
256 mA
Termination current
256 mA
Temperature profile
JEITA
Safety timer
8 hours
new charge cycle starts when the following conditions are valid:
Converter starts
Battery charging is enabled by I2C register bit (REG01[5:4]) = 01 and CE is low
No thermistor fault on TS1 and TS2
No safety timer fault
BATFET is not forced to turn off (REG07[5])
The charger device automatically terminates the charging cycle when the charging current is below termination
threshold and charge voltage is above recharge threshold. When a full battery voltage is discharged below
recharge threshold (REG04[0]), the bq24193 automatically starts another charging cycle.
The STAT output indicates the charging status of charging (LOW), charging complete or charge disable (HIGH)
or charging fault (Blinking). The status register REG08[5:4] indicates the different charging phases: 00-charging
disable, 01-precharge, 10-fast charge (constant current) and constant voltage mode, 11-charging done. Once a
charging cycle is complete, an INT is asserted to notify the host.
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
17
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
The host can always control the charging operation and optimize the charging parameters by writing to the
registers through I2C.
8.3.3.2 Battery Charging Profile
The device charges the battery in three phases: preconditioning, constant current and constant voltage. At the
beginning of a charging cycle, the device checks the battery voltage and applies current.
Table 4. Charging Current Setting
VBAT
CHARGING CURRENT
REG DEFAULT SETTING
REG08[5:4]
3V
REG02[7:2]
2048 mA
10
If the charger device is in DPM regulation or thermal regulation during charging, the actual charging current will
be less than the programmed value. In this case, termination is temporarily disabled and the charging safety
timer is counted at half the clock rate.
Regulation Voltage
(3.5V – 4.4V)
Battery Voltage
Fast Charge Current
(500mA-4020mA)
Charge Current
VBAT_LOWV (2.8V/3V)
VBAT_SHORT (2V)
IPRECHARGE (128mA-2048mA)
ITERMINATION (128mA-2048mA)
IBATSHORT (100mA)
Trickle Charge
Pre-charge
Fast Charge and Voltage Regulation
Safety Timer
Expiration
Figure 13. Battery Charging Profile
8.3.3.3 Battery Path Impedance IR Compensation
To speed up the charging cycle, we would like to stay in constant current mode as long as possible. In real
system, the parasitic resistance, including routing, connector, MOSFETs and sense resistor in the battery pack,
may force the charger device to move from constant current loop to constant voltage loop too early, extending
the charge time.
The bq24193 allows the user to compensate for the parasitic resistance by increasing the voltage regulation set
point according to the actual charge current and the resistance. For safe operation, the user should set the
maximum allowed regulation voltage to REG06[4:2], and the minimum trace parasitic resistance (REG06[7:5]).
(
)
VBATREG_ACTUAL = VBATREG_I2C + lower of ICHRG_ACTUAL × RCOMP and VCLAMP
18
Submit Documentation Feedback
(1)
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
8.3.3.4 Thermistor Qualification
The bq24193 continuously monitors battery temperature and applies JEITA profile with TS1/TS2 shorted. It
measures the voltage between the TS pins and ground, typically determined by a negative temperature
coefficient thermistor and an external voltage divider. The device compares this voltage against its internal
thresholds to determine if charging is allowed.
8.3.3.4.1 JEITA Guideline Compliance
To improve the safety of charging Li-ion batteries, JEITA guideline was released on April 20, 2007. The guideline
emphasized the importance of avoiding a high charge current and high charge voltage at certain low and high
temperature ranges.
To initiate a charge cycle, the voltage on TS pin must be within the VT1 to VT5 thresholds. If TS voltage exceeds
the T1–T5 range, the controller suspends charging and waits until the battery temperature is within the T1 to T5
range. At cool temperature (T1–T2), JEITA recommends the charge current to be reduced to at least half of the
charge current or lower. At warm temperature (T3–T5), JEITA recommends charge voltage less than 4.1 V.
The bq24193 provides flexibility voltage/current settings beyond the JEITA requirement. The voltage setting at
warm temperature (T3–T5) can be 4.2 V or 4.05 V (REG07 bit[4]). The current setting at cool temperature
(T1–T2) can be further reduced to 20% of fast charge current (REG05 bit[0]).
Charging Current
1ICHG
Charging Voltage
4.2V
VSET=1
4.10V
4.05V
0.5ICHG
ISET=1
0.2ICHG
VSET=0
ISET=0
T1 T2
100C
0 0C
T3
450C
T5
60 0C
T1 T2
00C 100C
T3
450C
T5
600C
The resistor bias network has been updated as below.
1 ö
æ 1
VVREF ´ RTHCOLD ´ RTHHOT ´ ç
÷
è VT1 VT5 ø
RT2 =
æV
ö
æV
ö
RTHHOT ´ ç VREF - 1÷ - RTHCOLD ´ ç VREF - 1÷
è VT5
ø
è VT1
ø
VVREF
-1
VT1
RT1 =
1
1
+
RT2 RTHCOLD
(2)
Select 0°C to 60°C range for Li-ion or Li-polymer battery,
RTHT1 = 27.28 kΩ
RTHT5 = 3.02 kΩ
RT1 = 2.27 kΩ
RT2 = 6.86 kΩ
8.3.3.5 Charging Termination
The bq24193 terminates a charge cycle when the battery voltage is above recharge threshold, and the current is
below termination current. After the charging cycle is complete, the BATFET turns off. The converter keeps
running to power the system, and BATFET can turn back on to engage supplement mode.
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
19
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
When termination occurs, the status register REG09[5:4] is 11, and an INT is asserted to the host. Termination is
temporarily disabled if the charger device is in input current/voltage regulation or thermal regulation. Termination
can be disabled by writing 0 to REG05[7].
8.3.3.5.1 Termination when REG02[0] = 1
When REG02[0] is HIGH to reduce the charging current by 80%, the charging current could be less than the
termination current. The charger device termination function should be disabled. When the battery is charged to
fully capacity, the host disables charging through CE pin or REG01[5:4].
8.3.3.5.2 Termination when REG05[6] = 1
Usually the STAT bit indicates charging complete when the charging current falls below termination threshold.
Write REG05[6] = 1 to enable an early “charge done” indication on STAT pin. The STAT pin goes high when the
charge current reduces below 800 mA. The charging cycle is still on-going until the current falls below the
termination threshold.
8.3.3.6 Charging Safety Timer
The bq24193 has safety timer to prevent extended charging cycle due to abnormal battery conditions.
In default mode, the device keeps charging the battery with 5-hour fast charging safety timer regardless of
REG05[2:1] default value. At the end of the 5 hours, the EN_HIZ (REG00[7]) is set to signal the buck converter
stops and the system load is supplied by the battery. The EN_HIZ bit can be cleared to restart the buck
converter.
In host mode, the device keeps charging the battery until the fast charging safety timer expired. The duration of
safety timer can be set by the REG05[2:1] bits (default = 8 hours). At the end of safety timer, the EN_HIZ
(REG00[7]) is cleared to signal the buck converter continues to operation to supply system load.
The safety timer is 1 hour when the battery is below BATLOWV threshold. The user can program fast charge
safety timer through I2C (REG05[2:1]). When safety timer expires, the fault register REG09[5:4] goes 11 and an
INT is asserted to the host. The safety timer feature can be disabled via I2C (REG05[3]).
The following actions restart the safety timer:
• At the beginning of a new charging cycle
• Toggle the CE pin HIGH to LOW to HIGH (charge enable)
• Write REG01[5:4] from 00 to 01 (charge enable)
• Write REG05[3] from 0 to 1 (safety timer enable)
• Write REG01[7] to 1 (software reset)
During input voltage/current regulation or thermal regulation, the safety timer counts at half clock rate since the
actual charge current is likely to be below the register setting. For example, if the charger is in input current
regulation (IINDPM) throughout the whole charging cycle, and the safety time is set to 5 hours, the safety timer
will expire in 10 hours. This feature can be disabled by writing 0 to REG07[6].
8.3.3.7 USB Timer when Charging from USB100mA Source
The total charging time in default mode from USB100-mA source is limited by a 45-min max timer. At the end of
the timer, the device stops the converter and goes to HIZ.
8.3.4 Status Outputs (PG, STAT, and INT)
8.3.4.1 Power Good Indicator (PG)
In bq24193, PG goes LOW to indicate a good input source when:
1. VBUS above UVLO
2. VBUS above battery (not in sleep)
3. VBUS below ACOV threshold
4. VBUS above 3.8 V when 30-mA current is applied (not a poor source)
20
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
8.3.4.2 Charging Status Indicator (STAT)
The bq24193 indicates charging state on the open drain STAT pin. The STAT pin can drive LED as the
application diagram shows.
Table 5. STAT Pin State
CHARGING STATE
STAT
Charging in progress (including recharge)
LOW
Charging complete
HIGH
Sleep mode, charge disable
HIGH
Charge suspend (Input over-voltage, TS fault, timer fault, input or system overvoltage)
blinking at 1Hz
8.3.4.3 Interrupt to Host (INT)
In some applications, the host does not always monitor the charger operation. The INT notifies the system on the
device operation. The following events will generate 256-us INT pulse.
• USB/adapter source identified (through PSEL and OTG pins)
• Good input source detected
– VVBUS - VBAT > VSLEEPZ
– VVBUS > VACOV
– current limit above IBADSRC
• Input removed
• Charge Complete
• Any FAULT event in REG09
When a fault occurs, the charger device sends out INT and keeps the fault state in REG09 until the host reads
the fault register. Before the host reads REG09 and all the faults are cleared, the charger device would not send
any INT upon new faults. In order to read the current fault status, the host has to read REG09 two times
consecutively. The 1st reads fault register status from the last read and the 2nd reads the current fault register
status.
8.3.5 Protections
8.3.5.1 Input Current Limit on ILIM
For safe operation, the bq24193 has an additional hardware pin on ILIM to limit maximum input current on ILIM
pin. The input maximum current is set by a resistor from ILIM pin to ground as:
1V
IINMAX =
´ 530
RILIM
(3)
The actual input current limit is the lower value between ILIM setting and register setting (REG00[2:0]). For
example, if the register setting is 111 for 3 A, and ILIM has a 353-Ω resistor to ground for 1.5 A, the input current
limit is 1.5 A. ILIM pin can be used to set the input current limit rather than the register settings.
The device regulates ILIM pin at 1 V. If ILIM voltage exceeds 1 V, the device enters input current regulation
(Refer to Dynamic Power Path Management section).
The voltage on the ILIM pin is proportional to the input current. The ILIM pin can be used to monitor the input
current per Equation 4:
V
I IN = ILIM ´ IINMAX
(4)
1V
For example, if the ILIM pin sets 2 A, and the ILIM voltage is 0.6 V, the actual input current is 1.2 A. If the ILIM
pin is open, the input current is limited to zero since ILIM voltage floats above 1 V. If the ILIM pin is short, the
input current limit is set by the register.
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
21
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
8.3.5.2 Thermal Regulation and Thermal Shutdown
The bq24193 monitors the internal junction temperature TJ to avoid overheat the chip and limits the IC surface
temperature. When the internal junction temperature exceeds the preset limit (REG06[1:0]), the device lowers
down the charge current. The wide thermal regulation range from 60°C to 120°C allows the user to optimize the
system thermal performance.
During thermal regulation, the actual charging current is usually below the programmed battery charging current.
Therefore, termination is disabled, the safety timer runs at half the clock rate, and the status register REG08[1]
goes high.
Additionally, the device has thermal shutdown to turn off the converter. The fault register REG09[5:4] is 10 and
an INT is asserted to the host.
8.3.5.3 Voltage and Current Monitoring in Buck Mode
The bq24193 closely monitor the input and system voltage, as well as HSFET and LSFET current for safe buck
mode operation.
8.3.5.3.1 Input Over-Voltage (ACOV)
The maximum input voltage for buck mode operation is . If VBUS voltage exceeds , the device stops switching
immediately. During input over voltage (ACOV), the fault register REG09[5:4] will be set to 01. An INT is asserted
to the host.
8.3.5.3.2 System Over-Voltage Protection (SYSOVP)
The charger device monitors the voltage at SYS. When system over-voltage is detected, the converter is stopped
to protect components connected to SYS from high voltage damage.
8.3.5.4 Voltage and Current Monitoring in Boost Mode
The bq24193closely monitors the VBUS voltage, as well as HSFET and LSFET current to ensure safe boost
mode operation.
8.3.5.4.1 VBUS Over-Voltage Protection
The boost mode regulated output is 5 V. When an adapter plugs in during boost mode, the VBUS voltage will
rise above regulation target. Once the VBUS voltage exceeds 5.3 V, the bq24193stops switching and the device
exits boost mode. The fault register REG09[6] is set high to indicate fault in boost operation. An INT is asserted
to the host.
8.3.5.5 Battery Protection
8.3.5.5.1 Battery Over-Current Protection (BATOVP)
The battery over-voltage limit is clamped at 4% above the battery regulation voltage. When battery over voltage
occurs, the charger device immediately disables charge. The fault register REG09[5] goes high and an INT is
asserted to the host.
8.3.5.5.2 Charging During Battery Short Protection
If the battery voltage falls below 2 V, the charge current is reduced to 100 mA for battery safety.
8.3.5.5.3 System Over-Current Protection
If the system is shorted or exceeds the over-current limit, the BATFET is latched off. DC source insertion on
VBUS is required to reset the latch-off condition and turn on BATFET.
22
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
8.3.6 Serial Interface
The bq24193 uses I2C compatible interface for flexible charging parameter programming and instantaneous
device status reporting. I2C is a bi-directional 2-wire serial interface developed by Philips Semiconductor (now
NXP Semiconductors). Only two bus lines are required: a serial data line (SDA) and a serial clock line (SCL).
Devices can be considered as masters or slaves when performing data transfers. A master is the device which
initiates a data transfer on the bus and generates the clock signals to permit that transfer. At that time, any
device addressed is considered a slave.
The device operates as a slave device with address 6BH, receiving control inputs from the master device like
micro controller or a digital signal processor. The I2C interface supports both standard mode (up to 100 kbits),
and fast mode (up to 400 kbits).
Both SDA and SCL are bi-directional lines, connecting to the positive supply voltage via a current source or pullup resistor. When the bus is free, both lines are HIGH. The SDA and SCL pins are open drain.
8.3.6.1 Data Validity
The data on the SDA line must be stable during the HIGH period of the clock. The HIGH or LOW state of the
data line can only change when the clock signal on the SCL line is LOW. One clock pulse is generated for each
data bit transferred.
SDA
SCL
Data line stable;
Data valid
Change
of data
allowed
Figure 14. Bit Transfer on the I2C Bus
8.3.6.2 START and STOP Conditions
All transactions begin with a START (S) and can be terminated by a STOP (P). A HIGH to LOW transition on the
SDA line while SCl is HIGH defines a START condition. A LOW to HIGH transition on the SDA line when the
SCL is HIGH defines a STOP condition.
START and STOP conditions are always generated by the master. The bus is considered busy after the START
condition, and free after the STOP condition.
SDA
SDA
SCL
SCL
STOP (P)
START (S)
Figure 15. START and STOP conditions
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
23
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
8.3.6.3 Byte Format
Every byte on the SDA line must be 8 bits long. The number of bytes to be transmitted per transfer is
unrestricted. Each byte has to be followed by an Acknowledge bit. Data is transferred with the Most Significant
Bit (MSB) first. If a slave cannot receive or transmit another complete byte of data until it has performed some
other function, it can hold the clock line SCL low to force the master into a wait state (clock stretching). Data
transfer then continues when the slave is ready for another byte of data and release the clock line SCL.
Acknowledgement
signal from receiver
Acknowledgement
signal from slave
MSB
SDA
SCL
S or Sr
2
1
7
8
2
1
9
ACK
START or
Repeated
START
8
9
ACK
P or Sr
STOP or
Repeated
START
Figure 16. Data Transfer on the I2C Bus
8.3.6.4 Acknowledge (ACK) and Not Acknowledge (NACK)
The acknowledge takes place after every byte. The acknowledge bit allows the receiver to signal the transmitter
that the byte was successfully received and another byte may be sent. All clock pulses, including the
acknowledge 9th clock pulse, are generated by the master.
The transmitter releases the SDA line during the acknowledge clock pulse so the receiver can pull the SDA line
LOW and it remains stable LOW during the HIGH period of this clock pulse.
When SDA remains HIGH during the 9th clock pulse, this is the Not Acknowledge signal. The master can then
generate either a STOP to abort the transfer or a repeated START to start a new transfer.
8.3.6.5 Slave Address and Data Direction Bit
After the START, a slave address is sent. This address is 7 bits long followed by the eighth bit as a data direction
bit (bit R/W). A zero indicates a transmission (WRITE) and a one indicates a request for data (READ).
SDA
SCL
S
1-7
8
9
START
ADDRESS
R/W
ACK
8
1-7
9
8
1-7
ACK
DATA
DATA
9
P
ACK
STOP
Figure 17. Complete Data Transfer
8.3.6.5.1 Single Read and Write
1
7
1
1
8
1
8
1
1
S
Slave Address
0
ACK
Reg Addr
ACK
Data Addr
ACK
P
Figure 18. Single Write
1
7
1
1
8
1
1
7
1
1
S
Slave Address
0
ACK
Reg Addr
ACK
S
Slave Address
1
ACK
8
1
1
Data
NCK
P
Figure 19. Single Read
24
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
If the register address is not defined, the charger IC send back NACK and go back to the idle state.
8.3.6.5.2 Multi-Read and Multi-Write
The charger device supports multi-read and multi-write on REG00 through REG08.
1
7
1
1
8
1
S
Slave Address
0
ACK
Reg Addr
ACK
8
1
8
1
8
1
1
Slave Address
ACK
Data to Addr+1
ACK
Data to Addr+1
ACK
P
Figure 20. Multi-Write
1
7
1
1
8
1
1
7
1
1
S
Slave Address
0
ACK
Reg Addr
ACK
S
Slave Address
1
ACK
8
Data @ Addr
1
ACK
8
1
Data @ Addr+1
ACK
8
1
1
Data @ Addr+1
ACK
P
Figure 21. Multi-Read
The fault register REG09 locks the previous fault and only clears it after the register is read. For example, if
Charge Safety Timer Expiration fault occurs but recovers later, the fault register REG09 reports the fault when it
is read the first time, but returns to normal when it is read the second time. To verify real time fault, the fault
register REG09 should be read twice to get the real condition. In addition, the fault register REG09 does not
support multi-read or multi-write.
8.4 Device Functional Modes
8.4.1 Host Mode and Default Mode
The bq24193 is a host controlled device, but it can operate in default mode without host management. In default
mode, bq24193 can be used as an autonomous charger with no host or with host in sleep.
When the charger is in default mode, REG09[7] is HIGH. When the charger is in host mode, REG09[7] is LOW.
After power-on-reset, the device starts in watchdog timer expiration state, or default mode. All the registers are in
the default settings.
Any write command to bq24193 transitions the device from default mode to host mode. All the device parameters
can be programmed by the host. To keep the device in host mode, the host has to reset the watchdog timer by
writing 1 to REG01[6] before the watchdog timer expires (REG05[5:4]), or disable watchdog timer by setting
REG05[5:4] = 11.
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
25
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
Device Functional Modes (continued)
POR
watchdog timer expired
Reset registers
I2C interface enabled
Host Mode
Y
I2C Write?
Start watchdog timer
Host programs registers
N
Default Mode
Reset watchdog timer
Reset registers
N
Y
Reset REG01
bit[6]?
Y
N
I2C Write?
Y
N
Watchdog Timer
Expired?
Figure 22. Watchdog Timer Flow Chart
8.4.1.1 Plug in USB100mA Source with Good Battery
When the input source is detected as 100-mA USB host, and the battery voltage is above batgood threshold
(VBATGD), the charger device enters HIZ state to meet the battery charging spec requirement.
If the charger device is in host mode, it will stay in HIZ state even after the USB100-mA source is removed, and
the adapter plugs in. During the HIZ state, REG00[7] is set HIGH and the system load is supplied from battery. It
is recommended that the processor host always checks if the charger IC is in HIZ state when it wakes up. The
host can write REG00[7] to 0 to exit HIZ state.
If the charger is in default mode, when the DC source is removed, the charger device will get out of HIZ state
automatically. When the input source plugs in again, the charger IC runs detection on the input source and
update the input current limit.
8.4.1.2 USB Timer when Charging from USB 100-mA Source
The total charging time in default mode from USB 100-mA source is limited by a 45-min max timer. At the end of
the timer, the device stops the converter and goes to HIZ.
8.5 Register Map
Table 6. Register Map
REGISTER
26
REGISTER NAME
RESET
REG00
Input Source Control Register
00110000, or 30
REG01
Power-On Configuration Register
00011011, or 1B
REG02
Charge Current Control Register
01100000, or 60
REG03
Pre-Charge/Termination Current Control Register
00010001, or 11
REG04
Charge Voltage Control Register
10110010, or B2
REG05
Charge Termination/Timer Control Register
10011010, or 9A
REG06
IR Compensation / Thermal Regulation Control Register
00000011, or 03
REG07
Misc Operation Control Register
01001011, or 4B
REG08
System Status Register
—
REG09
Fault Register
—
REG0A
Vender / Part / Revision Status Register
—
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
8.5.1 I2C Registers
Address: 6BH. REG00-07 support Read and Write. REG08-0A are read only.
8.5.1.1 Input Source Control Register REG00 (reset = 00110000, or 30)
Figure 23. REG00 Input Source Control Register Format
7
EN_HIZ
R/W
6
VINDPM[3]
R/W
5
VINDPM[2]
R/W
4
VINDPM[1]
R/W
3
VINDPM[0]
R/W
2
IINLIM[2]
R/W
1
IINLIM[1]
R/W
0
IINLIM[0]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 7. REG00 Input Source Control Register Description
BIT
FIELD
TYPE
RESET
DESCRIPTION
Bit 7
EN_HIZ
R/W
0
0 – Disable, 1 – Enable
Default: Disable (0)
Offset 3.88 V, Range: 3.88 V to 5.08 V
Default: 4.36 V (0110)
Input Voltage Limit
Bit 6
VINDPM[3]
R/W
0
640 mV
Bit 5
VINDPM[2]
R/W
1
320 mV
Bit 4
VINDPM[1]
R/W
1
160 mV
Bit 3
VINDPM[0]
R/W
0
80 mV
Input Current Limit (Actual input current limit is the lower of I2C and ILIM)
Bit 2
IINLIM[2]
R/W
0
Bit 1
IINLIM[1]
R/W
0
Bit 0
IINLIM[0]
R/W
0
000 – 100 mA, 001 – 150 mA,
010 – 500 mA,
011 – 900 mA, 100 – 1.2 A,
101 – 1.5 A,
110 – 2 A, 111 – 3 A
Default SDP: 100 mA (000)(OTG pin = 0) or 500
mA (010)
(OTG pin = 1)
Default DCP/CDP: 3 A (111)
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
27
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
8.5.1.2 Power-On Configuration Register REG01 (reset = 00011011, or 1B)
Figure 24. REG01 Power-On Configuration Register Format
7
6
Register Reset I2C Watchdog
Timer Reset
R/W
R/W
5
CHG_CONFIG[1]
4
CHG_CONFIG[0]
3
SYS_MIN[2]
2
SYS_MIN[1]
1
SYS_MIN[0]
0
BOOST_LIM
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 8. REG01 Power-On Configuration Register Description
BIT
FIELD
TYPE
RESET
DESCRIPTION
NOTE
Bit 7
Register Reset
R/W
0
0 – Keep current register setting,
1 – Reset to default
Default: Keep current register setting (0)
Back to 0 after register reset
Bit 6
I2C Watchdog
Timer Reset
R/W
0
0 – Normal ; 1 – Reset
Default: Normal (0)
Back to 0 after timer reset
Charger Configuration
Bit 5
CHG_CONFIG[1]
R/W
0
CHG_CONFIG[0]
R/W
1
00 – Charge Disable, 01 – Charge
Battery,
10/11 – OTG
Default: Charge Battery (01)
Bit 4
Offset: 3.0 V, Range 3.0 V to 3.7 V
Default: 3.5 V (101)
Minimum System Voltage Limit
Bit 3
SYS_MIN[2]
R/W
1
0.4 V
Bit 2
SYS_MIN[1]
R/W
0
0.2 V
Bit 1
SYS_MIN[0]
R/W
1
0.1 V
R/W
1
0 – 500 mA, 1 – 1.3 A
Boost Mode Current Limit
Bit 0
28
BOOST_LIM
Submit Documentation Feedback
Default: 1.3 A (1)
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
8.5.1.3 Charge Current Control Register REG02 (reset = 01100000, or 60)
Figure 25. REG02 Charge Current Control Register Format
7
ICHG[5]
R/W
6
ICHG[4]
R/W
5
ICHG[3]
R/W
4
ICHG[2]
R/W
3
ICHG[1]
R/W
2
ICHG[0]
R/W
1
Reserved
R/W
0
FORCE_20PCT
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 9. REG02 Charge Current Control Register Description
BIT
FIELD
TYPE
RESET
DESCRIPTION
NOTE
Offset: 512 mA
Range: 512 to 4544 mA
Default: 2048 mA (011000)
Fast Charge Current Limit
Bit 7
ICHG[5]
R/W
0
2048 mA
Bit 6
ICHG[4]
R/W
1
1024 mA
Bit 5
ICHG[3]
R/W
1
512 mA
Bit 4
ICHG[2]
R/W
0
256 mA
Bit 3
ICHG[1]
R/W
0
128 mA
Bit 2
ICHG[0]
R/W
0
64 mA
Bit 1
Reserved
R/W
0
0 - Reserved
Reserved. Must write "0"
Bit 0
FORCE_20PCT
R/W
0
0 – ICHG as REG02[7:2] programmed
1 – ICHG as 20% of REG02[7:2]
programmed
Default: ICHG as REG02[7:2] programmed
(0)
8.5.1.4 Pre-Charge/Termination Current Control Register REG03 (reset = 00010001, or 11)
Figure 26. REG03 Pre-Charge/Termination Current Control Register Format
7
IPRECHG[3]
R/W
6
IPRECHG[2]
R/W
5
IPRECHG[1]
R/W
4
IPRECHG[0]
R/W
3
ITERM[3]
R/W
2
ITERM[2]
R/W
1
ITERM[1]
R/W
0
ITERM[0]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 10. REG03 Pre-Charge/Termination Current Control Register Description
BIT
FIELD
TYPE
RESET
DESCRIPTION
NOTE
Offset: 128 mA,
Range: 128 mA to 2048 mA
Default: 256 mA (0001)
Pre-Charge Current Limit
Bit 7
IPRECHG[3]
R/W
0
1024 mA
Bit 6
IPRECHG[2]
R/W
0
512 mA
Bit 5
IPRECHG[1]
R/W
0
256 mA
Bit 4
IPRECHG[0]
R/W
1
128 mA
Termination Current Limit
Bit 3
ITERM[3]
R/W
0
1024 mA
Bit 2
ITERM[2]
R/W
0
512 mA
Bit 1
ITERM[1]
R/W
0
256 mA
Bit 0
ITERM[0]
R/W
1
128 mA
Offset: 128 mA
Range: 128 mA to 2048 mA
Default: 256 mA (0001)
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
29
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
8.5.1.5 Charge Voltage Control Register REG04 (reset = 10110010, or B2)
Figure 27. REG04 Charge Voltage Control Register Format
7
VREG[5]
R/W
6
VREG[4]
R/W
5
VREG[3]
R/W
4
VREG[2]
R/W
3
VREG[1]
R/W
2
VREG[0]
R/W
1
BATLOWV
R/W
0
VRECHG
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 11. REG04 Charge Voltage Control Register Description
BIT
FIELD
TYPE
RESET
DESCRIPTION
NOTE
Offset: 3.504 V
Range: 3.504 V to 4.400 V (111000)
Default: 4.208 V (101100)
Charge Voltage Limit
Bit 7
VREG[5]
R/W
1
512 mV
Bit 6
VREG[4]
R/W
0
256 mV
Bit 5
VREG[3]
R/W
1
128 mV
Bit 4
VREG[2]
R/W
1
64 mV
Bit 3
VREG[1]
R/W
0
32 mV
Bit 2
VREG[0]
R/W
0
16 mV
Battery Precharge to Fast Charge Threshold
Bit 1
BATLOWV
R/W
1
0 – 2.8 V, 1 – 3.0 V
Default: 3.0 V (1)
Battery Recharge Threshold (below battery regulation voltage)
Bit 0
VRECHG
R/W
0
0 – 100 mV, 1 – 300 mV
Default: 100 mV (0)
8.5.1.6 Charge Termination/Timer Control Register REG05 (reset = 10011010, or 9A)
Figure 28. REG05 Charge Termination/Timer Control Register Format
7
EN_TERM
R/W
6
TERM_STAT
R/W
5
4
WATCHDOG[1] WATCHDOG[0]
R/W
R/W
3
EN_TIMER
R/W
2
1
CHG_TIMER[1] CHG_TIMER[0]
R/W
R/W
0
JEITA_ISET
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 12. REG05 Charge Termination/Timer Control Register Description
BIT
FIELD
TYPE
RESET
DESCRIPTION
NOTE
R/W
1
0 – Disable, 1 – Enable
Default: Enable termination (1)
R/W
0
0 – Match ITERM,
1 – STAT pin high before actual
termination when charge current
below 800 mA
Default Match ITERM (0)
00 – Disable timer, 01 – 40 s,
10 – 80 s, 11 – 160 s
Default: 40 s (01)
Charging Termination Enable
Bit 7
EN_TERM
Termination Indicator Threshold
Bit 6
TERM_STAT
I2C Watchdog Timer Setting
Bit 5
WATCHDOG[1]
R/W
0
Bit 4
WATCHDOG[0]
R/W
1
Charging Safety Timer Enable
Bit 3
EN_TIMER
R/W
1
0 – Disable, 1 – Enable
Default: Enable (1)
00 – 5 hrs, 01 – 8 hrs, 10 – 12
hrs, 11 – 20 hrs
Default: 8 hours (01)
(See Charging Safety Timer for details)
0 – 50%, 1 – 20%
Percentage w.r.t ICHG REG02[7:2]
Default: 50% (0)
Fast Charge Timer Setting
Bit 2
CHG_TIMER[1]
R/W
0
Bit 1
CHG_TIMER[0]
R/W
1
JEITA Low Temperature Current Setting
Bit 0
30
JEITA_ISET (0°C to
10°C)
R/W
0
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
8.5.1.7 IR Compensation / Thermal Regulation Control Register REG06 (reset = 00000011, or 03)
Figure 29. REG06 IR Compensation / Thermal Regulation Control Register Format
7
BAT_COMP[2]
R/W
6
BAT_COMP[1]
R/W
5
BAT_COMP[0]
R/W
4
VCLAMP[2]
R/W
3
VCLAMP[1]
R/W
2
VCLAMP[0]
R/W
1
TREG[1]
R/W
0
TREG[0]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 13. REG06 IR Compensation / Thermal Regulation Control Register Description
BIT
FIELD
TYPE
RESET
DESCRIPTION
NOTE
Range: 0 to 70 mΩ
Default: 0 Ω (000)
IR Compensation Resistor Setting
Bit 7
BAT_COMP[2]
R/W
0
40 mΩ
Bit 6
BAT_COMP[1]
R/W
0
20 mΩ
Bit 5
BAT_COMP[0]
R/W
0
10 mΩ
IR Compensation Voltage Clamp (above regulation voltage)
Bit 4
VCLAMP[2]
R/W
0
64 mV
Bit 3
VCLAMP[1]
R/W
0
32 mV
Range: 0 to 112 mV
Default: 0 mV (000)
Bit 2
VCLAMP[0]
R/W
0
16 mV
00 – 60°C, 01 – 80°C, 10 –
100°C, 11 – 120°C
Thermal Regulation Threshold
Bit 1
TREG[1]
R/W
1
Bit 0
TREG[0]
R/W
1
Default: 120°C (11)
8.5.1.8 Misc Operation Control Register REG07 (reset = 01001011, or 4B)
Figure 30. REG07 Misc Operation Control Register Format
7
DPDM_EN
R/W
6
TMR2X_EN
R/W
5
BATFET_Disable
R/W
4
JEITA_VSET
R/W
3
Reserved
R/W
2
Reserved
R/W
1
INT_MASK[1]
R/W
0
INT_MASK[0]
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 14. REG07 Misc Operation Control Register Description
BIT
FIELD
TYPE
RESET
DESCRIPTION
NOTE
0 – Not in D+/D– detection;
1 – Force D+/D– detection
Default: Not in D+/D– detection (0),
Back to 0 after detection complete
Set default input current limit from PSEL/OTG pins
Bit 7
DPDM_EN
R/W
0
Safety Timer Setting during Input DPM and Thermal Regulation
Bit 6
TMR2X_EN
R/W
1
0 – Safety timer not slowed by 2X during Default: Safety timer slowed by 2X (1)
input DPM or thermal regulation,
1 – Safety timer slowed by 2X during
input DPM or thermal regulation
Force BATFET Off
Bit 5
BATFET_Disable
R/W
0
0 – Allow Q4 turn on, 1 – Turn off Q4
Default: Allow Q4 turn on(0)
Bit 4
JEITA_VSET (45°C60°C)
R/W
0
0 – VREG, 1 – VREG_200mV
Default: VREG(0)
Bit 3
Reserved
R/W
1
1 – Reserved. Must write "1"
Bit 2
Reserved
R/W
0
0 – Reserved. Must write "0"
Bit 1
INT_MASK[1]
R/W
1
0 – No INT during CHRG_FAULT, 1 –
INT on CHRG_FAULT
Default: INT on CHRG_FAULT (1)
Bit 0
INT_MASK[0]
R/W
1
0 – No INT during BAT_FAULT, 1 – INT
on BAT_FAULT
Default: INT on BAT_FAULT (1)
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
31
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
8.5.1.9 System Status Register REG08
Figure 31. REG08 System Status Register Format
7
VBUS_STAT[1]
R
6
VBUS_STAT[0]
R
5
CHRG_STAT[1]
R
4
CHRG_STAT[0]
R
3
DPM_STAT
R
2
PG_STAT
R
1
THERM_STAT
R
0
VSYS_STAT
R
LEGEND: R = Read only; -n = value after reset
Table 15. REG08 System Status Register Description
BIT
FIELD
TYPE
DESCRIPTION
Bit 7
VBUS_STAT[1]
R
Bit 6
VBUS_STAT[0]
R
00 – Unknown (no input, or DPDM detection incomplete), 01 – USB host, 10 – Adapter
port, 11 – OTG
Bit 5
CHRG_STAT[1]
R
Bit 4
CHRG_STAT[0]
R
Bit 3
DPM_STAT
R
0 – Not DPM, 1 – VINDPM or IINDPM
Bit 2
PG_STAT
R
0 – Not Power Good, 1 – Power Good
Bit 1
THERM_STAT
R
0 – Normal, 1 – In Thermal Regulation
Bit 0
VSYS_STAT
R
0 – Not in VSYSMIN regulation (BAT > VSYSMIN), 1 – In VSYSMIN regulation (BAT <
VSYSMIN)
00 – Not Charging, 01 – Pre-charge ( VBATUVLO
connected to BAT. The source current rating needs to be at least 3 A in order for the buck converter of the
charger to provide maximum output power to SYS.
11 Layout
11.1 Layout Guidelines
The switching node rise and fall times should be minimized for minimum switching loss. Proper layout of the
components to minimize high frequency current path loop (see Figure 45) is important to prevent electrical and
magnetic field radiation and high frequency resonant problems. Here is a PCB layout priority list for proper
layout. Layout PCB according to this specific order is essential.
1. Place input capacitor as close as possible to PMID pin and GND pin connections and use shortest copper
trace connection or GND plane.
2. Place inductor input terminal to SW pin as close as possible. Minimize the copper area of this trace to lower
electrical and magnetic field radiation but make the trace wide enough to carry the charging current. Do not
use multiple layers in parallel for this connection. Minimize parasitic capacitance from this area to any other
trace or plane.
3. Put output capacitor near to the inductor and the IC. Ground connections need to be tied to the IC ground
with a short copper trace connection or GND plane.
4. Route analog ground separately from power ground. Connect analog ground and connect power ground
separately. Connect analog ground and power ground together using power pad as the single ground
connection point. Or using a 0-Ω resistor to tie analog ground to power ground.
5. Use single ground connection to tie charger power ground to charger analog ground. Just beneath the IC.
Use ground copper pour but avoid power pins to reduce inductive and capacitive noise coupling.
6. Decoupling capacitors should be placed next to the IC pins and make trace connection as short as possible.
7. It is critical that the exposed power pad on the backside of the IC package be soldered to the PCB ground.
Ensure that there are sufficient thermal vias directly under the IC, connecting to the ground plane on the
other layers.
8. The via size and number should be enough for a given current path.
See the EVM design for the recommended component placement with trace and via locations. For the VQFN
information, refer to SCBA017 and SLUA271.
Figure 45. High Frequency Current Path
38
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
11.2 Layout Example
CPMID
PGND
Top layer
L
CBUS
PGND
CREGN CBTST
RBTST
2nd layer (PGND)
PGND
VBUS
CSYS
PIN1
via
VSYS
PGND
VBAT
PGND
PGND on
Top layer
CBAT
PGND
PGND
Figure 46. Layout Example Diagram
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
39
bq24193
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
www.ti.com
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
• bq24193 EVM (PWR021) User’s Guide (SLUUA14)
• Quad Flatpack No-Lead Logic Packages Application Report (SCBA017)
• QFN/SON PCB Attachment Application Report (SLUA271)
12.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
40
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
bq24193
www.ti.com
SLUSBG7A – DECEMBER 2014 – REVISED NOVEMBER 2017
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2014–2017, Texas Instruments Incorporated
Product Folder Links: bq24193
41
PACKAGE OPTION ADDENDUM
www.ti.com
19-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
BQ24193RGER
ACTIVE
VQFN
RGE
24
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BQ24193
Samples
BQ24193RGET
ACTIVE
VQFN
RGE
24
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BQ24193
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
