ISO7821LLSEVM

User's Guide SLLU240 – March 2016 ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Evaluation Module This user’s guide describes the reinforced, isolated dual-LVDS buffer evaluation module (EVM) for the ISO7821LL, ISO7821LLS, and ISO7820LL devices. This EVM allows designers to evaluate device performance for fast development and analysis of isolated systems. The EVM supports evaluation of any of the Texas Instrument's isolated dual-LVDS buffers in a 16-pin DW package. CAUTION This evaluation module is made available for evaluation of isolator parameter performance only and is not intended for isolation voltage testing. To prevent damage to the EVM, any voltage applied as a supply or digital input/output must be maintained within the 0-V to 5.5-V recommended operating range. 1 2 3 4 5 6 7 Contents Introduction ................................................................................................................... Overview ...................................................................................................................... Pin Configurations of the ISO7821LL, ISO7821LLS, ISO7820LL Isolated Dual-LVDS Buffers ................... ISO782xLLx – EVM Board Block Diagram and Image ................................................................. EVM Setup and Operation .................................................................................................. Bill of Materials ............................................................................................................... EVM Schematics and Layout .............................................................................................. 2 2 2 3 5 7 7 List of Figures 1 ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Pin Configurations .............. 2 2 ISO7821LL EVM Configuration ............................................................................................ 3 3 ISO7821LL EVM Photograph .............................................................................................. 4 4 EVM Setup for Operation ................................................................................................... 5 5 Typical Input and Output Waveforms—Differential Probes ............................................................ 6 6 Typical Output Waveforms—Single-Ended Probes ..................................................................... 6 7 Eye Diagram at 100-Mbps Data Rate ..................................................................................... 6 8 Eye Diagram at 150-Mbps Data Rate ..................................................................................... 6 9 ISO7821LL, ISO7820LL, and ISO7821LLS EVM Schematic .......................................................... 8 10 ISO7821LL, ISO7820LL, and ISO7821LLS EVM PCB Layout ........................................................ 9 List of Tables 1 Bill of Materials ............................................................................................................... 7 SLLU240 – March 2016 Submit Documentation Feedback ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Evaluation Module Copyright © 2016, Texas Instruments Incorporated 1 Introduction 1 www.ti.com Introduction This user’s guide describes EVM operation with respect to the ISO7821LL, ISO7821LLS, and ISO7820LL reinforced, isolated dual-LVDS buffers. However, the EVM can be reconfigured for evaluation of any of TI’s isolated dual-LVDS buffers in a 16-pin DW package. This guide also describes the available channel configurations of the ISO7821LL, ISO7821LLS, and ISO7820LL devices, the EVM schematic, and typical test setup. A typical input and output waveform is also presented. 2 Overview The ISO7821LL, ISO7821LLS, and ISO7820LL devices are TI’s new digital isolator family capable of galvanic isolations up to 8000 VPK. These isolators provide high electromagnetic immunity and low emissions at low-power consumption, while isolating the LVDS bus signal. Each isolation channel has an LVDS receiver and transmitter separated by a silicon-oxide (SiO2) insulation barrier. Used with isolated power supplies, these devices block high voltages, isolate grounds, and prevent noise currents on a data bus or other circuits from entering the local ground and interfering with or damaging sensitive circuitry. 3 Pin Configurations of the ISO7821LL, ISO7821LLS, ISO7820LL Isolated Dual-LVDS Buffers Figure 1 shows the pin configurations for the ISO7821LL, ISO7821LLS, and ISO7820LL isolated dualLVDS buffers. ISO7821LL ISO7821LLS ISO7820LL 16 VCC2 VCC1 1 16 VCC2 GND1 2 15 GND2 GND1 2 15 GND2 INA + 3 14 OUTA + INA + 3 14 OUTA + INA ± 4 13 OUTA ± INA ± 4 12 INB ± INB ± 5 11 INB + INB + 6 11 OUTB + NC 7 10 OUTB ± 5 OUTB + 6 EN1 7 GND1 8 10 EN2 9 GND2 GND1 8 ISOLATION 1 ISOLATION VCC1 13 OUTA ± 12 OUTB ± EN2 9 GND2 Figure 1. ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Pin Configurations 2 ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Evaluation Module Copyright © 2016, Texas Instruments Incorporated SLLU240 – March 2016 Submit Documentation Feedback ISO782xLLx – EVM Board Block Diagram and Image www.ti.com 4 ISO782xLLx – EVM Board Block Diagram and Image Figure 2 shows the typical board configuration for evaluation of the ISO7821LL isolated dual-LVDS buffer. VCC1 1 3 Input INA+ R1 100 Ω Input INA– 4 5 Output OUTB– R2 100 Ω Output OUTB+ 6 7 2 8 VCC1 VCC2 VCC1 VCC2 INAP OUTAP INAM OUTAM OUTBM INBM OUTBP INBP EN1 GND1 GND1 EN2 GND2 GND2 16 14 Output OUTA+ R3 100 Ω 13 Output OUTA– 12 Input INB– R4 11 100 Ω Input INB+ 10 9 15 VCC2 U1 GND1 GND2 C1 10 µF C2 1 µF C6 0.1 µF C3 0.1 µF C5 1 µF C4 10 µF GND2 GND1 Copyright © 2016, Texas Instruments Incorporated Figure 2. ISO7821LL EVM Configuration SLLU240 – March 2016 Submit Documentation Feedback ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Evaluation Module Copyright © 2016, Texas Instruments Incorporated 3 ISO782xLLx – EVM Board Block Diagram and Image www.ti.com Figure 3 shows a photograph of the EVM. Figure 3. ISO7821LL EVM Photograph 4 ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Evaluation Module Copyright © 2016, Texas Instruments Incorporated SLLU240 – March 2016 Submit Documentation Feedback EVM Setup and Operation www.ti.com 5 EVM Setup and Operation This section describes the setup and operation of the EVM for parameter performance evaluation. Figure 4 shows the configuration for operating the ISO7821LL, ISO7821LLS, and ISO7820LL isolated dual-LVDS buffer EVM using two power supplies. R5 0 INA_C_P TP8 TP2 TP1 VCC1 C8 5pF J5 1 2 3 4 R9 51.1 C9 5pF J6 GND1 J7 644695-4 GND1 R10 51.1 C7 5pF R1 GND1 R6 100 GND1 R7 R8 R2 0 0 VCC1: 3V-5.5V FnG GND1 0 INA_C_N OUTB_C_N C10 5pF 100 VCC2 R11 51.1 OSC C11 5pF C12 5pF J2 OSC J10 TP3 1 2 3 4 J9 R12 51.1 TP5 FnG C6 C5 C4 0.1µF 1µF 10µF TP6 VCC2 GND2 644695-4 J16 GND1 GND1 GND1 GND2 OUTB_C_P GND2 J1 VCC2: 3V-5.5V R13 C13 0 OUTA_C_P 5pF J13 1 2 3 4 VCC2 R17 51.1 VCC1 C14 1 INA_P 3 INA_N 4 OUTB_N 5 OUTB_P 6 7 TP7 2 8 VCC1 VCC1 VCC2 INAP OUTAP INAM OUTAM OUTBM INBM OUTBP INBP EN1 GND1 GND1 EN2 GND2 GND2 5pF J12 644695-4 16 14 13 C15 5pF OUTA_P R3 100 OUTA_N GND2 R14 R18 51.1 GND2 0 GND2 12 11 INB_N R4 INB_P R15 R16 100 INB_C_N C16 10 OUTA_C_N 0 0 FnG 5pF J15 TP4 R19 51.1 9 15 C17 5pF 1 2 3 4 J14 J3 U1 C18 5pF GND2 J8 C1 C2 C3 10µF 1µF 0.1µF 644695-4 R20 51.1 GND1 J11 GND2 J4 GND2 GND2 INB_C_P OSC GND2 GND1 GND1 OSC Copyright © 2016, Texas Instruments Incorporated OSC = oscilloscope FnG = function generator Figure 4. EVM Setup for Operation To setup the EVM, use the following steps: Step 1. Connect the VCC1 power supply to J7 and the VCC2 power supply to J16. Step 2. Set the supply voltages, VCC1 and VCC2, to 5 V and 200-mA compliance. Step 3. Connect the function generator for the ISO7821LL and ISO7821LLS EVMs to J5 and J15 and for the ISO7820LL EVM to J5 and J10 on differential inputs (connect the FnG + signal to pin 2 (INx+), the FnG – signal to pin 3 (INx–), and the FnG ground to pin 1 and pin 4). Step 4. Set the output square wave of the function generator to 50 MHz for the ISO7821LL and ISO7820LL EVMs and 75 MHz for the ISO7821LLS EVM with a 1.2-V DC bias (unbalanced) ± 400 mVPP. Connect the positive output of the function generator to one differential line and the negative output to another differential line. Step 5. Enable both the positive and negative differential outputs of the function generator. Step 6. Probe (preferably using differential probes) the signals at J1, J2, J3 and J4. For the ISO7821LL and ISO7821LLS EVM, the differential output is at J2 and J3. For the ISO7820LL EVM, the differential output is at J3 and J4. The differential output is a 1.2-V DC bias with ±400 mVPP when measured with single ended probes and is a 0-V DC bias with ±800 mVPP when measured with differential probes. SLLU240 – March 2016 Submit Documentation Feedback ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Evaluation Module Copyright © 2016, Texas Instruments Incorporated 5 EVM Setup and Operation www.ti.com Figure 5 shows the typical waveforms for the channel 1 and channel 2 outputs for the ISO7821LL device using differential probes. Figure 6 shows the typical waveforms for the channel 1 and channel 2 outputs for the ISO7821LL device using single-ended probes. Figure 7 shows the typical eye diagram for the ISO7821LL device at a 100-Mbps data rate. Figure 8 shows the typical eye diagram for the ISO7821LLS device at a 150-Mbps data rate. To check the common mode voltage of the 1.2-V DC bias, use the following steps: • For the ISO7821LL and ISO7821LLS EVMs: Step 1. Depopulate R2 and R3 Step 2. Populate C10, C11, C12, C13, C14, C15, R7, R8, R11, R12, R13, R14, R17, and R18 Step 3. Probe J9 and J12 • For the ISO7820LL EVM: Step 1. Depopulate R3 and R4 Step 2. Populate C13, C14, C15, C16, C17, C18, R13, R14, R15, R16, R17, R18, R19, and R20 Step 3. Probe J12 and J14 6 Figure 5. Typical Input and Output Waveforms—Differential Probes Figure 6. Typical Output Waveforms—Single-Ended Probes Figure 7. Eye Diagram at 100-Mbps Data Rate Figure 8. Eye Diagram at 150-Mbps Data Rate ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Evaluation Module Copyright © 2016, Texas Instruments Incorporated SLLU240 – March 2016 Submit Documentation Feedback Bill of Materials www.ti.com 6 Bill of Materials Table 1 lists the bill of materials (BOM) for this EVM. Table 1. Bill of Materials Designator Quantity Description Value Package Reference Manufacturer INT009-001 (for ISO7821LLDWR) INT009-002 (for ISO7820LLDWR) INT009-003 (for ISO7821LLSDWR) Any PCB 1 Printed Circuit Board H1, H2, H3, H4 4 Bumpon, Hemisphere, 0.44 X 0.20, Clear 440x200 mil SJ-5303 (CLEAR) #M High-Performance, 8000 VPK Reinforced Isolated Dual LVDS Buffer, DW0016B DW0016B ISO7821LLDWR Texas Instruments High-Performance, 8000 VPK Reinforced Isolated Dual LVDS Buffer, DW0016B DW0016B ISO7820LLDWR Texas Instruments High-Performance, 8000 VPK Reinforced Isolated Dual LVDS Buffer, DW0016B DW0016B ISO7821LLSDWR Texas Instruments Header, 100mil, 2x1, Gold, TH HTSW-102-07-G-S Samtec U1 1 J1, J2, J3, J4, J6, J7, J8, J9, J11, J12, J14, J16 12 CONN HEADER 2POS .100" T/H GOLD C7, C8, C9, C10, C11, C12, C13, C14, C15, C16, C17, C18 DNP CAP, CERM, 5 pF, 50 V, ± 5%, C0G/NP0, 0402 5 pF 0402 GRM1555C1H5R0CA01D MuRata C2, C5 2 CAP, CERM, 1 µF, 50 V, ± 10%, X5R, 0603 1 µF 0603 GRM188R61H105KAALD MuRata C1, C4 2 CAP, CERM, 10 µF, 35 V, ± 10%, X5R, 0805 10 µF 0805 GRM21BR6YA106KE43L MuRata FID1, FID2, FID3 0 Fiducial mark. There is nothing to buy or mount. Fiducial N/A N/A R5, R6 2 RES, 0, 5%, 0.063 W, 0402 0Ω 0402 ERJ-2GE0R00X Panasonic R13, R14 0 RES, 0, 5%, 0.063 W, 0402 0Ω 0402 ERJ-2GE0R00X Panasonic Panasonic DNP RES, 0, 5%, 0.063 W, 0402 0Ω 0402 ERJ-2GE0R00X (for ISO7821LLDWR and ISO7821LLSDWR) 2 RES, 0, 5%, 0.063 W, 0402 0Ω 0402 ERJ-2GE0R00X (for ISO7820LLDWR) Panasonic 2 RES, 0, 5%, 0.063 W, 0402 0Ω 0402 ERJ-2GE0R00X (for ISO7821LLDWR and ISO7821LLSDWR) Panasonic DNP RES, 0, 5%, 0.063 W, 0402 0Ω 0402 ERJ-2GE0R00X (for ISO7820LLDWR) Panasonic R1, R2, R3, R4 4 RES, 100, 1%, 0.063 W, 0402 100 Ω 0402 CRCW0402100RFKED Vishay-Dale R9, R10, R11, R12, R17, R18, R19, R20 DNP RES, 51.1, 1%, 0.063 W, 0402 51.1 Ω 0402 CRCW040251R1FKED Vishay-Dale Header, 100mil, 4x1, Tin, TH 644695-4 TE Connectivity 0603 06033C104JAT2A AVX Test Point, Miniature, SMT 5019 Keystone R7, R8 R15, R16 J5, J10, J13, J15 4 CONN HEADER VERT 4POS .100 TIN C3, C6 2 CAP, CERM, 0.1 µF, 25 V, ± 5%, X7R, 0603 TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 7 PartNumber 8 Test Point, Miniature, SMT 0.1 µF EVM Schematics and Layout Separate orderable EVMs are available for each isolated dual-LVDS buffer (ISO7821LL, ISO7821LLS, and ISO7820LL). The EVMs must be modified only in the placement of the 100-Ω termination resistors at the input and output (only if needed) of each channel. Figure 9 shows the ISO7821LL, ISO7821LLS, and ISO7820LL EVM schematic and Figure 10 shows the printed-circuit board (PCB) layout. SLLU240 – March 2016 Submit Documentation Feedback ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Evaluation Module Copyright © 2016, Texas Instruments Incorporated 7 EVM Schematics and Layout www.ti.com R5 0 INA_C_P TP8 TP2 TP1 VCC1 C8 5pF J5 1 2 3 4 R9 51.1 C9 5pF J6 GND1 J7 644695-4 GND1 R10 51.1 C7 5pF R1 GND1 R6 100 VCC1: 3V-5.5V GND1 0 GND1 R7 R8 R2 0 0 INA_C_N OUTB_C_N C10 5pF 100 VCC2 R11 51.1 C11 5pF C12 5pF J2 J10 TP3 1 2 3 4 J9 R12 51.1 TP5 C6 C5 C4 0.1µF 1µF 10µF TP6 VCC2 GND2 644695-4 J16 GND1 GND1 GND1 GND2 OUTB_C_P GND2 J1 VCC2: 3V-5.5V R13 C13 0 OUTA_C_P 5pF J13 1 2 3 4 VCC2 R17 51.1 VCC1 C14 1 INA_P 3 INA_N 4 OUTB_N 5 OUTB_P 6 7 TP7 2 8 VCC1 VCC1 VCC2 INAP OUTAP INAM OUTAM OUTBM INBM OUTBP INBP EN1 GND1 GND1 EN2 GND2 GND2 5pF J12 644695-4 16 14 13 OUTA_P R3 100 OUTA_N C15 5pF GND2 R14 R18 51.1 GND2 0 GND2 11 INB_N R4 INB_P 10 TP4 12 100 R15 R16 OUTA_C_N 0 0 INB_C_N C16 5pF J15 R19 51.1 9 15 C17 5pF 1 2 3 4 J14 J3 U1 C18 5pF GND2 J8 C1 C2 C3 10µF 1µF 0.1µF 644695-4 R20 51.1 GND1 J11 GND2 J4 GND2 GND2 INB_C_P GND2 GND1 GND1 Copyright © 2016, Texas Instruments Incorporated Figure 9. ISO7821LL, ISO7820LL, and ISO7821LLS EVM Schematic 8 ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Evaluation Module Copyright © 2016, Texas Instruments Incorporated SLLU240 – March 2016 Submit Documentation Feedback EVM Schematics and Layout www.ti.com Figure 10. ISO7821LL, ISO7820LL, and ISO7821LLS EVM PCB Layout SLLU240 – March 2016 Submit Documentation Feedback ISO7821LL, ISO7821LLS, ISO7820LL Reinforced Isolated Dual-LVDS Buffer Evaluation Module Copyright © 2016, Texas Instruments Incorporated 9 STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES 1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein. Acceptance of the EVM is expressly subject to the following terms and conditions. 1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software 1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned, or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production system. 2 Limited Warranty and Related Remedies/Disclaimers: 2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License Agreement. 2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as mandated by government requirements. TI does not test all parameters of each EVM. 2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM, or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day warranty period. 3 Regulatory Notices: 3.1 United States 3.1.1 Notice applicable to EVMs not FCC-Approved: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and software developers to write software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter. 3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant: CAUTION This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Interference Statement for Class A EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER FCC Interference Statement for Class B EVM devices NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3.2 Canada 3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 Concerning EVMs Including Radio Transmitters: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Concernant les EVMs avec appareils radio: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Concerning EVMs Including Detachable Antennas: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Concernant les EVMs avec antennes détachables Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur 3.3 Japan 3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に 輸入される評価用キット、ボードについては、次のところをご覧ください。 http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified by TI as conforming to Technical Regulations of Radio Law of Japan. If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of Japan to follow the instructions below with respect to EVMs: 1. 2. 3. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of Japan, Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to EVMs, or Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan. SPACER SPACER SPACER SPACER SPACER 【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの 措置を取っていただく必要がありますのでご注意ください。 1. 2. 3. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用 いただく。 実験局の免許を取得後ご使用いただく。 技術基準適合証明を取得後ご使用いただく。 なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。 上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ ンスツルメンツ株式会社 東京都新宿区西新宿６丁目２４番１号 西新宿三井ビル 3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page 電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page SPACER 4 EVM Use Restrictions and Warnings: 4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS. 4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information related to, for example, temperatures and voltages. 4.3 Safety-Related Warnings and Restrictions: 4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or property damage. If there are questions concerning performance ratings and specifications, User should contact a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit components may have elevated case temperatures. These components include but are not limited to linear regulators, switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the information in the associated documentation. When working with the EVM, please be aware that the EVM may become very warm. 4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the dangers and application risks associated with handling electrical mechanical components, systems, and subsystems. User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees, affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or designees. 4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal, state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local requirements. 5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as accurate, complete, reliable, current, or error-free. SPACER SPACER SPACER SPACER SPACER SPACER SPACER 6. Disclaimers: 6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS. 6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF THE EVM. 7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES, EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED. 8. Limitations on Damages and Liability: 8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED. 8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT. 9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s) will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s), excluding any postage or packaging costs. 10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas, without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas. Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated spacer IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2016, Texas Instruments Incorporated