Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
SN5414, SN54LS14, SN7414, SN74LS14
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
SNx414 and SNx4LS14 Hex Schmitt-Trigger Inverters
1 Features
3 Description
•
•
•
Each circuit in SNx414 and SNx4LS14 functions as
an inverter. However, because of the Schmitt-Trigger
action, they have different input threshold levels for
positive-going (VT+) and negative-going (VT–) signals.
1
Operation From Very Slow Edges
Improved Line-Receiving Characteristics
High Noise Immunity
2 Applications
•
•
•
•
•
•
HVAC Gateways
Residential Ductless Air Conditioning Outdoor
Units
Robotic Controls
Industrial Stepper Motors
Power Meter and Power Analyzers
Digital Input Modules for Factory Automation
These circuits are temperature compensated and can
be triggered from the slowest of input ramps and still
give clean, jitter-free output signals.
Device Information(1)
PART NUMBER
SN7414,
SN74LS14
SN5414,
SN54LS14
PACKAGE
BODY SIZE (NOM)
SOIC (14)
4.90 mm × 3.91 mm
SSOP (14)
6.20 mm × 5.30 mm
PDIP (14)
19.30 mm × 6.35 mm
SO (14)
10.30 mm × 5.30 mm
CDIP (14)
19.56 mm × 6.67 mm
CFP (14)
9.21 mm × 5.97 mm
LCCC (20)
8.89 mm × 8.89 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Logic Diagram (Positive Logic)
A
Y
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
SN5414, SN54LS14, SN7414, SN74LS14
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
6.7
4
4
4
4
5
5
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Switching Characteristics ..........................................
Typical Characteristics ..............................................
Parameter Measurement Information .................. 9
7.1 Series SN5414 and SN7414 Devices ....................... 9
7.2 Series SN54LS14 and SN74LS14 Devices ............ 11
8
Detailed Description ............................................ 13
8.1 Overview ................................................................. 13
8.2 Functional Block Diagram ....................................... 13
8.3 Feature Description................................................. 13
8.4 Device Functional Modes........................................ 13
9
Application and Implementation ........................ 14
9.1 Application Information............................................ 14
9.2 Typical Application .................................................. 14
9.3 System Examples ................................................... 16
10 Power Supply Recommendations ..................... 17
11 Layout................................................................... 17
11.1 Layout Guidelines ................................................. 17
11.2 Layout Example .................................................... 17
12 Device and Documentation Support ................. 18
12.1
12.2
12.3
12.4
12.5
12.6
Related Links ........................................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
18
18
18
18
18
18
13 Mechanical, Packaging, and Orderable
Information ........................................................... 18
4 Revision History
Changes from Revision B (February 2002) to Revision C
Page
•
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section. ................................................................................................. 1
•
Deleted Ordering Information table; see the Package Option Addendum at the end of the data sheet ............................... 1
•
Changed Package thermal impedance, RθJA, values in Thermal Information table From: 86°C/W To: 90.1°C/W (D),
From: 96°C/W To: 105.4°C/W (DB), From: 80°C/W To: 54.9°C/W (N), and From: 76°C/W To: 88.8°C/W (NS)................... 4
2
Submit Documentation Feedback
Copyright © 1983–2016, Texas Instruments Incorporated
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
SN5414, SN54LS14, SN7414, SN74LS14
www.ti.com
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
5 Pin Configuration and Functions
D, DB, N, NS, J, or W Package
14-Pin SOIC, SSOP, PDIP, SO, CDIP, or CFP
Top View
5
10
5Y
6
9
4A
GND
7
8
4Y
2A
4
18
6Y
NC
5
17
NC
2Y
6
16
5A
NC
7
15
NC
3A
8
14
5Y
9
3Y
6A
3A
19
5A
Not to scale
13
11
NC
4
VCC
2Y
1
6Y
20
6A
12
12
13
3
11
2
2A
1A
1Y
2
VCC
10
14
1Y
1
3
1A
FK Package
20-Pin LCCC
Top View
4A
4Y
NC
GND
3Y
Not to scale
NC – No internal connection
Pin Functions
PIN
I/O
DESCRIPTION
SOIC, SSOP, TVSOP, CDIP,
PDIP,TSSOP, CFP
LCCC
1A
1
2
I
Channel 1 input
1Y
2
3
O
Channel 1 output
2A
3
4
I
Channel 2 input
2Y
4
6
O
Channel 2 output
3A
5
8
I
Channel 3 input
3Y
6
9
O
Channel 3 output
4A
9
13
I
Channel 4 input
4Y
8
12
O
Channel 4 output
5A
11
16
I
Channel 5 input
5Y
10
14
O
Channel 5 output
6A
13
19
I
Channel 6 input
6Y
12
18
O
Channel 6 output
GND
7
10
—
Ground
NC
—
1, 5, 7,
11, 15, 17
—
No internal connection
VCC
14
20
—
Power supply
NAME
Copyright © 1983–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
3
SN5414, SN54LS14, SN7414, SN74LS14
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
MAX
UNIT
7
V
Supply voltage, VCC (2)
SNx414
Input voltage
5.5
SNx4LS14
Junction temperature, TJ
Storage temperature, Tstg
(1)
(2)
V
7
–65
150
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Voltage values are with respect to network ground terminal.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic
discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±1500
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±2000
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
VCC
Supply voltage
IOH
High-level output current
IOL
Low-level output current
MIN
NOM
MAX
SN5414, SN54LS14
4.5
5
5.5
SN7414, SN74LS14
4.75
5
5.25
SN5414, SN7414
–0.8
SN54LS14, SN74LS14
–0.4
SN5414, SN7414
TA
Operating free-air temperature
UNIT
V
mA
16
SN54LS14
4
SN74LS14
8
SN5414, SN54LS14
–55
125
SN7414, SN74LS14
0
70
mA
°C
6.4 Thermal Information
SNx414, SNx4LS14
THERMAL METRIC (1)
D (SOIC)
DB (SSOP)
N (PDIP)
NS (SO)
UNIT
14 PINS
14 PINS
14 PINS
14 PINS
Junction-to-ambient thermal resistance (2)
90.1
105.4
54.9
88.8
°C/W
RθJC(top) Junction-to-case (top) thermal resistance
50.3
57.3
42.5
46.5
°C/W
RθJB
Junction-to-board thermal resistance
44.3
52.7
34.7
47.5
°C/W
ψJT
Junction-to-top characterization parameter
17.9
22.5
27.8
16.8
°C/W
ψJB
Junction-to-board characterization parameter
44.1
52.2
34.6
47.2
°C/W
RθJA
(1)
(2)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
The package termal impedance is calculated in accordance with JESD 51-7.
Submit Documentation Feedback
Copyright © 1983–2016, Texas Instruments Incorporated
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
SN5414, SN54LS14, SN7414, SN74LS14
www.ti.com
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
6.5 Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
TEST CONDITIONS (1)
PARAMETER
VT+
VCC = 5 V
VT–
VCC = 5 V
Hysteresis
(VT+ – VT–)
VCC = 5 V
VIK
VOH
MIN
TYP (2)
SNx414
1.5
1.7
2
SNx4LS14
1.4
1.6
1.9
SNx414
0.6
0.9
1.1
SNx4LS14
0.5
0.8
1
0.4
0.8
–1.5
VCC = MIN, II = –18 mA, SNx4LS14
–1.5
VCC = MIN, VI = 0.6 V, IOH = –0.8 mA, SNx414
2.4
3.4
VCC = MIN, VI = 0.5 V, IOH = –0.4 mA, SNx4LS14
2.4
3.4
VCC = MIN, VI = 1.9 V
IT+
VCC = 5 V, VI = VT+
IT–
VCC = 5 V, VI = VT–
IOL = 4 mA, SNx4LS14
0.25
0.4
IOL = 8 mA, SN74LS14
0.35
0.5
SNx4LS14
–0.14
SNx414
–0.56
SNx4LS14
–0.18
IIH
1
0.1
VCC = MAX, VIH = 2.4 V, SNx414
40
VCC = MAX, VIH = 2.7 V, SNx4LS14
20
VCC = MAX, VIL = 0.4 V
IOS (3)
VCC = MAX
ICCH
VCC = MAX
ICCL
VCC = MAX
SNx414
V
V
mA
VCC = MAX, VI = 7 V, SNx4LS14
IIL
V
mA
VCC = MAX, VI = 5.5 V, SNx414
II
(1)
(2)
(3)
0.4
–0.43
V
V
0.2
SNx414
UNIT
V
VCC = MIN, II = –12 mA, SNx414
VCC = MIN, VI = 2 V, IOL = 16 mA, SNx414
VOL
MAX
–0.8
–1.2
SNx4LS14
–0.4
SNx414
–18
–55
SNx4LS14
–20
–100
SNx414
22
36
SNx4LS14
8.6
16
SNx414
39
60
SNx4LS14
12
21
mA
µA
mA
mA
mA
mA
For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
All typical values are at VCC = 5 V and TA = 25°C.
Not more than one output should be shorted at a time.
6.6 Switching Characteristics
VCC = 5 V, TA = 25°C, and over operating free-air temperature range (unless otherwise noted; see Figure 20)
PARAMETER
FROM (INPUT)
TO (OUTPUT)
TEST CONDITIONS
MIN
tPLH
A
Y
RL = 400 Ω and CL = 15 pF, or
RL = 2 kΩ and CL = 15 pF
tPHL
A
Y
RL = 400 Ω and CL = 15 pF, or
RL = 2 kΩ and CL = 15 pF
Copyright © 1983–2016, Texas Instruments Incorporated
TYP
MAX
15
22
ns
15
22
ns
Submit Documentation Feedback
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
UNIT
5
SN5414, SN54LS14, SN7414, SN74LS14
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
www.ti.com
6.7 Typical Characteristics
6.7.1 SNx414 Circuits
Data for temperatures below 0°C and above 70°C and supply voltage below 4.75 V and above 5.25 V are
applicable for SN5414 only.
0.90
VCC = 5 V
V T– – Negative-Going Threshold Voltage – V
V T+ – Positive-Going Threshold Voltage – V
1.70
1.69
1.68
1.67
1.66
1.65
1.64
1.63
1.62
1.61
VCC = 5 V
0.89
0.88
0.87
0.86
0.85
0.84
0.83
0.82
0.81
0.80
1.60
–75 –50
–25
0
25
50
75
100
125
–75 –50
0
–25
25
50
75
100
125
TA – Free-Air Temperature –°C
TA – Free-Air Temperature –°C
Figure 1. Positive-Going Threshold Voltage
vs Free-Air Temperature
Figure 2. Negative-Going Threshold Voltage
vs Free-Air Temperature
850
VCC = 5 V
TA = 25°C
VCC = 5 V
Relative Frequency of Occurence
840
V T+ – V T– – Hysteresis – mV
830
820
810
800
790
780
770
760
750
–75 –50
–25
0
25
50
75
100
740
125
760
Figure 3. Hysteresis vs Free-Air Temperature
820
840
860
880
900
2.0
TA = 25°C
1.6
Positive-Going Threshold Voltage, VT+
1.4
TA = 25°C
1.8
V T+ – VT– – Hysteresis – V
1.8
Threshold Voltage -– V
800
Figure 4. Distribution of Units for Hysteresis
2.0
1.2
1.0
0.8
Negative-Going Threshold Voltage, VT–
0.6
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.4
0.2
0.2
0
0
4.5
5
5.25
4.75
VT+ – VT– – Hysteresis – mV
5.5
Figure 5. Threshold Voltages vs Supply Voltage
6
780
VT+ – VT– – Hysteresis – mV
TA – Free-Air Temperature –°C
Submit Documentation Feedback
4.5
5
5.25
4.75
VCC – Supply Voltage – V
5.5
Figure 6. Hysteresis vs Supply Voltage
Copyright © 1983–2016, Texas Instruments Incorporated
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
SN5414, SN54LS14, SN7414, SN74LS14
www.ti.com
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
SNx414 Circuits (continued)
4
VO – Output Voltage – V
VCC = 5 V
TA = 25°C
VT–
VT+
3
2
1
0
0
0.4
0.8
1.2
1.6
2
VCC – Supply Voltage – V
Figure 7. Output Voltage vs Input Voltage
Copyright © 1983–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
7
SN5414, SN54LS14, SN7414, SN74LS14
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
www.ti.com
6.7.2 SNx4LS14 Circuits
Data for temperatures below 0°C and above 70°C and supply voltage below 4.75 V and above 5.25 V are
applicable for SNx4LS14 only.
0.90
VCC = 5 V
1.69
VT– – Negative-Going Threshold Voltage – V
V T+ – Positive-Going Threshold Voltage – V
1.70
1.68
1.67
1.66
1.65
1.64
1.63
1.62
1.61
VCC = 5 V
0.89
0.88
0.87
0.86
0.85
0.84
0.83
0.82
0.81
0.80
1.60
–75 –50
–25
0
25
50
75
100
–75 –50
125
TA – Free-Air Temperature –°C
Figure 8. Positive-Going Threshold Voltage
vs Free-Air Temperature
0
25
50
75
100
–25
TA – Free-Air Temperature –°C
125
Figure 9. Negative-Going Threshold Voltage
vs Free-Air Temperature
850
Relative Frequency of Occurence
V T+ – VT– – Hysteresis – V
VCC = 5 V
TA = 25°C
VCC = 5 V
840
830
820
810
800
790
780
770
99% ARE
ABOVE
735 mV
760
750
–75 –50
–25
0
25
50
75
100
720
125
TA – Free-Air Temperature –°C
740
760
780
800
820
840
860
880
VT+ – VT– – Hysteresis – mV
Figure 10. Hysteresis vs Free-Air Temperature
Figure 11. Distribution of Units for Hysteresis
4
2.0
VCC = 5 V
TA = 25°C
TA = 25°C
1.8
VT–
VT+
3
Positive-Going Threshold Voltage, VT+
1.4
VO – Output Voltage – V
Threshold Voltage – V
1.6
1.2
Negative-Going Threshold Voltage, VT–
1.0
0.8
Hysteresis, VT+ – VT–
0.6
2
1
0.4
0.2
0
0
4.5
4.75
5
5.25
5.5
VCC – Supply Voltage – V
Figure 12. Threshold Voltages and Hysteresis
vs Supply Voltage
8
Submit Documentation Feedback
0
0.8
0.4
1.2
1.6
2
VI – Input Voltage – V
Figure 13. Output Voltage vs Input Voltage
Copyright © 1983–2016, Texas Instruments Incorporated
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
SN5414, SN54LS14, SN7414, SN74LS14
www.ti.com
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
7 Parameter Measurement Information
7.1 Series SN5414 and SN7414 Devices
Test
Point
VCC
VCC
RL
RL
From Output
Under Test
CL
From Output
Under Test
Test
Point
CL
Figure 14. Load Circuit For
2-State Totem-Pole Outputs
VCC
Test
Point
Figure 15. Load Circuit For
Open-Collector Outputs
High-Level
Pulse
RL
1.5 V
1.5 V
S1
tw
From Output
Under Test
Low-Level
Pulse
CL
1 kΩ
1.5 V
1.5 V
S2
Figure 16. Load Circuit For 3-State Outputs
Figure 17. Voltage Waveforms Pulse Durations
3V
Timing
Input
3V
Input
1.5 V
1.5 V
1.5 V
0V
0V
th
tsu
Data
Input
tPLH
3V
1.5 V
1.5 V
tPHL
In-Phase
Output
VOH
1.5 V
0V
1.5 V
VOL
tPHL
tPLH
Out-of-Phase
Output
VOH
1.5 V
1.5 V
VOL
Figure 18. Voltage Waveforms
Setup and Hold Times
Copyright © 1983–2016, Texas Instruments Incorporated
Figure 19. Voltage Waveforms
Propagation Delay Times
Submit Documentation Feedback
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
9
SN5414, SN54LS14, SN7414, SN74LS14
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
www.ti.com
Series SN5414 and SN7414 Devices (continued)
3V
Output
Control
(low-level
enabling)
1.5 V
1.5 V
0V
tPZL
tPLZ
Waveform 1
≈1.5 V
1.5 V
VOL
tPZH
VOL + 0.5 V
tPHZ
VOH
Waveform 2
1.5 V
VOH – 0.5 V
≈1.5 V
A.
CL includes probe and jig capacitance.
B.
All diodes are 1N3064 or equivalent.
C.
Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output
control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the
output control.
D.
S1 and S2 are closed for tPLH, tPHL, tPHZ, and tPLZ; S1 is open and S2 is closed for tPZH; S1 is closed and S2 is open
for tPZL.
E.
All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO ≈ 50 Ω ; tr and tf ≤ 7
ns for Series SN5414 and SN7414 devices and tr and tf ≤ 2.5 ns for Series SN54S14 and SN74S14 devices.
F.
The outputs are measured one at a time with one input transition per measurement.
Figure 20. Voltage Waveforms Enable and Disable Times, 3-State Outputs
10
Submit Documentation Feedback
Copyright © 1983–2016, Texas Instruments Incorporated
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
SN5414, SN54LS14, SN7414, SN74LS14
www.ti.com
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
7.2 Series SN54LS14 and SN74LS14 Devices
Test
Point
VCC
VCC
RL
RL
From Output
Under Test
CL
From Output
Under Test
Test
Point
CL
Figure 21. Load Circuit For
2-State Totem-Pole Outputs
VCC
Test
Point
Figure 22. Load Circuit For
Open-Collector Outputs
High-Level
Pulse
RL
1.3 V
1.3 V
S1
tw
From Output
Under Test
Low-Level
Pulse
CL
5 kΩ
1.3 V
1.3 V
S2
Figure 23. Load Circuit For 3-State Outputs
Figure 24. Voltage Waveforms Pulse Durations
3V
Timing
Input
3V
Input
1.3 V
1.3 V
1.3 V
0V
0V
th
tsu
Data
Input
tPLH
3V
1.3 V
1.3 V
tPHL
In-Phase
Output
VOH
1.3 V
1.3 V
0V
VOL
tPHL
tPLH
Out-of-Phase
Output
VOH
1.3 V
1.3 V
VOL
Figure 25. Voltage Waveforms
Setup and Hold Times
Copyright © 1983–2016, Texas Instruments Incorporated
Figure 26. Voltage Waveforms
Propagation Delay Times
Submit Documentation Feedback
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
11
SN5414, SN54LS14, SN7414, SN74LS14
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
www.ti.com
Series SN54LS14 and SN74LS14 Devices (continued)
Output
Control
(low-level
enabling)
3V
1.3 V
1.3 V
0V
tPZL
Waveform 1
tPLZ
≈1.5 V
1.3 V
VOL
tPZH
VOL + 0.5 V
tPHZ
VOH
Waveform 2
1.3 V
VOH – 0.5 V
≈1.5 V
A.
CL includes probe and jig capacitance.
B.
All diodes are 1N3064 or equivalent.
C.
Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output
control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the
output control.
D.
S1 and S2 are closed for tPLH, tPHL, tPHZ, and tPLZ; S1 is open and S2 is closed for tPZH; S1 is closed and S2 is open
for tPZL.
E.
Phase relationships between inputs and outputs have been chosen arbitrarily for these examples.
F.
All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO ≈ 50 Ω, tr ≤ 1.5 ns,
tf ≤ 2.6 ns.
G.
The outputs are measured one at a time with one input transition per measurement.
Figure 27. Voltage Waveforms Enable and Disable Times, 3-State Outputs
12
Submit Documentation Feedback
Copyright © 1983–2016, Texas Instruments Incorporated
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
SN5414, SN54LS14, SN7414, SN74LS14
www.ti.com
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
8 Detailed Description
8.1 Overview
The SNx414 and SNx4LS14 Schmitt-Trigger devices contain six independent inverters. They perform the
Boolean function Y = A in positive logic.
Schmitt-Trigger inputs are designed to provide a minimum separation between positive and negative switching
thresholds. This allows for noisy or slow inputs that would cause problems such as oscillation or excessive
current draw with normal CMOS inputs.
8.2 Functional Block Diagram
A
Y
Copyright © 2016, Texas Instruments Incorporated
8.3 Feature Description
The device can operate from very slow transition edge inputs. This device has high noise immunity.
8.4 Device Functional Modes
Table 1 lists the functional modes of the SNx414 and SNx4LS14.
Table 1. Function Table
Copyright © 1983–2016, Texas Instruments Incorporated
INPUT A
OUTPUT Y
H
L
L
H
Submit Documentation Feedback
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
13
SN5414, SN54LS14, SN7414, SN74LS14
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The SNx414 and SNx4LS14 device is a Schmitt-Trigger input CMOS device that can be used for a multitude of
inverting buffer type functions. The application shown here takes advantage of the Schmitt-Trigger inputs to
produce a delay for a logic input.
9.2 Typical Application
Copyright © 2016, Texas Instruments Incorporated
Figure 28. Simplified Application Schematic
9.2.1 Design Requirements
This device uses CMOS technology. Take care to avoid bus contention because it can drive currents that would
exceed maximum limits. Parallel output drive can create fast edges into light loads, so consider routing and load
conditions to prevent ringing.
9.2.2 Detailed Design Procedure
This circuit is designed around an RC network that produces a slow input to the second inverter. The RC time
constant (τ) is calculated from: τ = RC.
The delay time for this circuit is from tdelay(min) = –ln |1 – VT+(min) / VCC| τ to tdelay(max) = –ln |1 – VT+(max) / VCC| τ. It
must be noted that the delay is consistent for each device, but because the switching threshold is only ensured
between the minimum and maximum value, the output pulse length varies between devices. These values must
be calculated by using the minimum and maximum ensured VT+ values in the Electrical Characteristics.
The resistor value must be chosen such that the maximum current to and from the SNx414/SNx4LS14 is 8 mA at
5-V VCC.
14
Submit Documentation Feedback
Copyright © 1983–2016, Texas Instruments Incorporated
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
SN5414, SN54LS14, SN7414, SN74LS14
www.ti.com
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
Typical Application (continued)
9.2.3 Application Curve
VCC
Voltage
VT+(max)
VT+
VT+ Typical
VT+(min)
tdelay (max)
t delay (min)
VT
(max)
|W
VCC
VT (min)
ln | 1
|W
VCC
ln | 1
VC
VOUT
0.0
t0
t0 + 2
t0 + 22
t0 + 32
t0 + 42
t0 + 52
Time
Figure 29. Ideal Capacitor Voltage and Output Voltage With Positive Switching Threshold
Copyright © 1983–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
15
SN5414, SN54LS14, SN7414, SN74LS14
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
www.ti.com
9.3 System Examples
Here are some examples of various applications using the SNx414 and SNx4LS14 device.
TTL System
VT+
VT–
Input
CMOS
Sine-Wave
Oscillator
Output
Figure 30. TTL System Interface For Slow Input
Waveforms
Figure 31. Pulse Shaper
0.1 Hz to 10 MHz
330Ω
VT+
VT–
Input
Input
Output
Figure 32. Multivibrator
Figure 33. Threshold Detector
Open-Collector
Output
Input
Input
A
Output
VT+
Point A
Output
Figure 34. Pulse Stretcher
16
Submit Documentation Feedback
Copyright © 1983–2016, Texas Instruments Incorporated
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
SN5414, SN54LS14, SN7414, SN74LS14
www.ti.com
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
10 Power Supply Recommendations
The power supply can be any voltage between the minimum and maximum supply voltage rating located in the
Recommended Operating Conditions. The VCC terminal must have a good bypass capacitor to prevent power
disturbance. TI recommends using a 0.1-µF capacitor on the VCC terminal, and must be placed as close as
possible to the pin for best results.
11 Layout
11.1 Layout Guidelines
When using multiple bit logic devices, inputs must never float. In many cases, functions or parts of functions of
digital logic devices are unused, for example, when only two inputs of a triple-input AND gate are used or only
three of the four buffer gates are used. Such inputs must not be left unconnected because the undefined
voltages at the outside connections result in undefined operational states. All unused inputs of digital logic
devices must be connected to a high or low bias to prevent them from floating. The logic level that must be
applied to any particular unused input depends on the function of the device. Generally they are tied to GND or
VCC, whichever makes more sense or is more convenient. Floating outputs are generally acceptable, unless the
part is a transceiver.
11.2 Layout Example
Vcc
Input
Unused Input
Output
Output
Unused Input
Input
Figure 35. Layout Diagram
Copyright © 1983–2016, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
17
SN5414, SN54LS14, SN7414, SN74LS14
SDLS049C – DECEMBER 1983 – REVISED NOVEMBER 2016
www.ti.com
12 Device and Documentation Support
12.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 2. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
SN5414
Click here
Click here
Click here
Click here
Click here
SN54LS14
Click here
Click here
Click here
Click here
Click here
SN7414
Click here
Click here
Click here
Click here
Click here
SN74LS14
Click here
Click here
Click here
Click here
Click here
12.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
18
Submit Documentation Feedback
Copyright © 1983–2016, Texas Instruments Incorporated
Product Folder Links: SN5414 SN54LS14 SN7414 SN74LS14
PACKAGE OPTION ADDENDUM
www.ti.com
4-Sep-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
5962-9665801Q2A
ACTIVE
LCCC
FK
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
59629665801Q2A
SNJ54LS
14FK
5962-9665801QCA
ACTIVE
CDIP
J
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9665801QC
A
SNJ54LS14J
5962-9665801QDA
ACTIVE
CFP
W
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9665801QD
A
SNJ54LS14W
5962-9665801VDA
ACTIVE
CFP
W
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9665801VD
A
SNV54LS14W
JM38510/31302BCA
ACTIVE
CDIP
J
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
JM38510/
31302BCA
Samples
M38510/31302BCA
ACTIVE
CDIP
J
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
JM38510/
31302BCA
Samples
SN5414J
ACTIVE
CDIP
J
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
SN5414J
Samples
SN54LS14J
ACTIVE
CDIP
J
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
SN54LS14J
Samples
SN7414D
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
7414
Samples
SN7414DG4
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
7414
Samples
SN7414DR
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
7414
Samples
SN7414N
ACTIVE
PDIP
N
14
25
RoHS & Green
NIPDAU
N / A for Pkg Type
0 to 70
SN7414N
Samples
SN7414NSR
ACTIVE
SO
NS
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
SN7414
Samples
SN74LS14D
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
LS14
Samples
SN74LS14DBR
ACTIVE
SSOP
DB
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
LS14
Samples
SN74LS14DE4
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
LS14
Samples
Addendum-Page 1
Samples
Samples
Samples
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
4-Sep-2022
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
SN74LS14DG4
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
LS14
Samples
SN74LS14DR
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
LS14
Samples
SN74LS14DRE4
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
LS14
Samples
SN74LS14DRG4
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
LS14
Samples
SN74LS14N
ACTIVE
PDIP
N
14
25
RoHS & Green
NIPDAU
N / A for Pkg Type
0 to 70
SN74LS14N
Samples
SN74LS14NE4
ACTIVE
PDIP
N
14
25
RoHS & Green
NIPDAU
N / A for Pkg Type
0 to 70
SN74LS14N
Samples
SN74LS14NSR
ACTIVE
SO
NS
14
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
74LS14
Samples
SNJ5414J
ACTIVE
CDIP
J
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
SNJ5414J
Samples
SNJ5414W
ACTIVE
CFP
W
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
SNJ5414W
Samples
SNJ54LS14FK
ACTIVE
LCCC
FK
20
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
59629665801Q2A
SNJ54LS
14FK
SNJ54LS14J
ACTIVE
CDIP
J
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9665801QC
A
SNJ54LS14J
SNJ54LS14W
ACTIVE
CFP
W
14
1
Non-RoHS
& Green
SNPB
N / A for Pkg Type
-55 to 125
5962-9665801QD
A
SNJ54LS14W
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Addendum-Page 2
Samples
Samples
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
4-Sep-2022
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of