0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
TLV320DAC3120IRHBR

TLV320DAC3120IRHBR

  • 厂商:

    BURR-BROWN(德州仪器)

  • 封装:

    VQFN-32_5X5MM-EP

  • 描述:

    IC MONO/AUD DAC CLASS-D LP 32QFN

  • 数据手册
  • 价格&库存
TLV320DAC3120IRHBR 数据手册
TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Low-Power Mono Audio DAC With Embedded miniDSP and Mono Class-D Speaker Amplifier Check for Samples: TLV320DAC3120 1 INTRODUCTION 1.1 • • • • 123 • • • • • • • • • • • • Features Mono Audio DAC With 95-dB SNR Instruction-Programmable Embedded miniDSP Supports 8-kHz to 192-kHz Sample Rates Mono Class-D BTL Speaker Driver (2.5 W Into 4 Ω or 1.6 W Into 8 Ω) Mono Headphone/Lineout Driver Two Single-Ended Inputs With Output Mixing and Level Control Microphone Bias Built-in Digital Audio Processing Blocks With User-Programmable Biquad, FIR Filters, and DRC Digital Sine-Wave Generator for Beeps and Clicks (PRB_P25) Programmable Digital Audio Processor for Bass Boost/Treble/EQ With up to Six Biquads for Playback Pin Control or Register Control for Digital Playback Volume-Control Settings Integrated PLL Used for Programmable Digital Audio Processor I2S, Left-Justified, Right-Justified, DSP, and TDM Audio Interfaces I2C Control With Register Auto-Increment Full Power-Down Control Power Supplies: – Analog: 2.7 V–3.6 V – Digital Core: 1.65 V–1.95 V – Digital I/O: 1.1 V–3.6 V – Class-D: 2.7 V–5.5 V (SPKVDD ≥ AVDD) • 5-mm × 5-mm 32-QFN Package 1.2 • • • Applications Portable Audio Devices eBook Portable Navigation Devices 1.3 Description The TLV320DAC3120 is a low-power, highly integrated, high-performance mono DAC with 24-bit mono playback. The device integrates several analog features, such as a microphone bias, headphone drivers, and a mono speaker driver capable of driving a 4-Ω load. The TLV320DAC3120 has a fully programmable miniDSP for digital audio processing. The digital audio data format is programmable to work with popular audio standard protocols (I2S, left/rightjustified) in master, slave, DSP, and TDM modes. Bass boost, treble, or EQ can be supported by the programmable digital-signal processing block. An onchip PLL provides the high-speed clock needed by the digital signal-processing block. The volume level can be controlled by either a pin control or by register control. The audio functions are controlled using the I2C serial bus. The TLV320DAC3120 is available in a 32-pin QFN package. 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. MATLAB is a trademark of The MathWorks, Inc. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2009–2012, Texas Instruments Incorporated TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. AVSS VOL/MICDET AVDD 7-Bit ADC HPVSS HPVDD SPKVSS SPKVSS SPKVDD SPKVDD P0/R116 Audio Output Stage Power Management Left and Right Volume-Control Register P0/R117 P1/R33–R34 GPIO1 GPIO SDA SCL De-Pop and Soft Start 2 I C Note: Normally, MCLK is PLL input; however, BCLK or GPIO1 can also be PLL input. MCLK RC CLK PLL P0/R63 L Data Digital R Data Audio Processing (L+R)/2 Data and Serial Interface WCLK SDIN BCLK Digital Vol miniDSP 24 dB to Mute Mono DAC MIXER P1/R35 DAC S P0/R64 Analog Attenuation 0 dB to –78 dB and Mute (0.5-dB steps) Class-D Speaker Driver P1/R38 P1/R42 6 dB to 24 dB (6-dB steps) SPKP SPKP SPKM SPKM Analog Class A/B Attenuation Headphone/Lineout Driver 0 dB to –78 dB and Mute 0 dB to 9 dB (0.5-dB steps) (1-dB steps) RESET P1/R36 P1/R40 AIN1 P1/R30–R31 HPOUT AIN2 P1/R46 MICBIAS 2 V/2.5 V/AVDD IOVSS IOVDD DVSS DVDD B0360-01 Figure 1-1. Functional Block Diagram NOTE This data manual is designed using PDF document-viewing features that allow quick access to information. For example, performing a global search on "page 0 / register 27" produces all references to this page and register in a list. This makes is easy to traverse the list and find all information related to a page and register. Note that the search string must be of the indicated format. Also, this document includes document hyperlinks to allow the user to quickly find a document reference. To come back to the original page, click the green left arrow near the PDF page number at the bottom of the file. The hot-key for this function is altleft arrow on the keyboard. Another way to find information quickly is to use the PDF bookmarks. 2 INTRODUCTION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 2 PACKAGE AND SIGNAL DESCRIPTIONS 2.1 Package/Ordering Information PRODUCT PACKAGE PACKAGE DESIGNATOR OPERATING TEMPERATURE RANGE TLV320DAC3120 QFN-32 RHB –40°C to 85°C 2.2 ORDERING NUMBER TRANSPORT MEDIA, QUANTITY TLV320DAC3120IRHBT Tape and reel, 250 TLV320DAC3120IRHBR Tape and reel, 3000 Device Information SPKP SPKVDD SPKVSS SPKM DVSS AVDD SPKVDD 24 25 SPKVSS SPKM RHB Package (Top View) 23 22 21 20 19 18 17 16 AVSS SPKP 26 15 NC 14 AIN2 HPOUT 27 HPVDD 28 13 AIN1 HPVSS 29 12 MICBIAS NC 30 11 VOL/MICDET RESET 31 10 SCL 9 SDA 32 1 2 3 4 5 6 7 8 IOVDD DVDD NC DIN WCLK BCLK MCLK GPIO1 IOVSS TLV320DAC3120 P0048-12 Table 2-1. TERMINAL FUNCTIONS TERMINAL NAME NO. AIN1 13 AIN2 AVDD I/O DESCRIPTION I Analog input #1 routed to output mixer 14 I Analog input #2 routed to output mixer 17 – Analog power supply AVSS 16 – Analog ground BCLK 7 I/O DIN 5 I Audio serial data input DVDD 3 – Digital power – digital core DVSS 18 – Digital ground GPIO1 32 I/O General-purpose input/output and multifunction pin HPOUT 27 O Headphone/lineout driver output HPVDD 28 – Headphone/line driver and PLL power HPVSS 29 – Headphone/line driver and PLL ground IOVDD 2 – Interface power IOVSS 1 – Interface ground Audio serial bit clock MCLK 8 I Exterrnal master clock MICBIAS 12 O Micophone bias voltage Copyright © 2009–2012, Texas Instruments Incorporated PACKAGE AND SIGNAL DESCRIPTIONS Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 3 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 2-1. TERMINAL FUNCTIONS (continued) TERMINAL NAME NO. NC I/O DESCRIPTION 4, 15, 30 – No connection RESET 31 I Device reset SCL 10 I/O I2C control-bus clock input SDA 9 I/O I2C control-bus data input SPKM 19, 23 O Class-D speaker driver inverting output SPKP 22, 26 O Class-D speaker driver noninverting output SPKVDD 21, 24 – Class-D speaker driver power supply SPKVSS 20, 25 – Class-D speaker driver power-supply ground VOL/MICDET 11 I Volume control or microphone/headphone/headset detection WCLK 6 I/O Audio serial word clock 3 ELECTRICAL SPECIFICATIONS 3.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) VALUE UNIT AVDD to AVSS –0.3 to 3.9 V DVDD to DVSS –0.3 to 2.5 V HPVDD to HPVSS –0.3 to 3.9 V SPKVDD to SPKVSS –0.3 to 6 V –0.3 to 3.9 V Digital input voltage IOVSS – 0.3 to IOVDD + 0.3 V Analog input voltage AVSS – 0.3 to AVDD + 0.3 V Operating temperature range –40 to 85 °C Storage temperature range –55 to 150 °C 105 °C IOVDD to IOVSS Junction temperature (TJ Max) Power dissipation QFN package (1) RθJA Thermal impedance (with thermal pad soldered to board) (TJ Max – TA)/RθJA W 35 °C/W Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Table 3-1. System Thermal Characteristics (1) (1) 4 Power Rating at 25°C Derating Factor Power Rating at 70°C Power Rating at 85°C 2.3 W 28.57 mW/°C 1W 0.6 W This data was taken using 2-oz. (0.071-mm thick) trace and copper pad that is soldered to a JEDEC high-K, standard 4-layer 3-in. × 3in. (7.62-cm × 7.62-cm) PCB. ELECTRICAL SPECIFICATIONS Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com 3.2 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) AVDD (1) MIN NOM (2) 2.7 3.3 3.6 Referenced to DVSS(2) 1.65 1.8 1.95 Referenced to HPVSS(2) 2.7 3.3 3.6 Referenced to SPKVSS(2) 2.7 Referenced to AVSS DVDD HPVDD Power-supply voltage range SPKVDD (1) (2) IOVDD Referenced to IOVSS Speaker impedance Load applied across class-D output pins (BTL) Headphone impedance AC-coupled to RL Analog audio full-scale input voltage AVDD = 3.3 V, single-ended Mono line output load impedance AC-coupled to RL MCLK (3) Master clock frequency IOVDD = 3.3 V SCL SCL clock frequency TA Operating free-air temperature VI (1) (2) (3) 3.3 1.1 MAX UNIT V 5.5 3.3 3.6 4 Ω 16 Ω 0.707 VRMS 10 –40 kΩ 50 MHz 400 kHz 85 °C To minimize battery-current leakage, the SPKVDD and SPKVDD voltage levels should not be below the AVDD voltage level. All grounds on board are tied together, so they should not differ in voltage by more than 0.2 V maximum for any combination of ground signals. By use of a wide trace or ground plane, ensure a low-impedance connection between HPVSS and DVSS. The maximum input frequency should be 50 MHz for any digital pin used as a general-purpose clock. Electrical Characteristics At 25°C, AVDD = HPVDD = IOVDD = 3.3 V, SPKVDD = 3.6 V, DVDD = 1.8 V, fS (audio) = 48 kHz, CODEC_CLKIN = 256 × fS, PLL = Off, VOL/MICDET pin disabled (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT INTERNAL OSCILLATOR—RC_CLK Oscillator frequency 8.2 MHz VOLUME CONTROL PIN (ADC); VOL/MICDET pin enabled Input voltage range VOL/MICDET pin configured as volume control (page 0 / register 116, bit D7 = 1 and page 0 / register 67, bit D7 = 0) 0.5 × AVDD 0 Input capacitance 2 Volume control steps V pF 128 Steps MICROPHONE BIAS Voltage output Voltage regulation Page 1 / register 46, bits D1–D0 = 10 2.25 2.5 Page 1 / register 46, bits D1–D0 = 01 2 At 4-mA load current, page 1 / register 46, bits D1–D0 = 10 (MICBIAS = 2.5 V) 5 At 4-mA load current, page 1 / register 46, bits D1–D0 = 01 (MICBIAS = 2 V) 7 2.75 mV ELECTRICAL SPECIFICATIONS Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 V 5 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Electrical Characteristics (continued) At 25°C, AVDD = HPVDD = IOVDD = 3.3 V, SPKVDD = 3.6 V, DVDD = 1.8 V, fS (audio) = 48 kHz, CODEC_CLKIN = 256 × fS, PLL = Off, VOL/MICDET pin disabled (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT DAC HEADPHONE OUTPUT, AC-COUPLED LOAD = 16 Ω (SINGLE-ENDED), DRIVER GAIN = 0 dB, PARASITIC CAPACITANCE = 30 pF Full-scale output voltage (0 dB) Output common-mode setting = 1.65 V SNR Signal-to-noise ratio Measured as idle-channel noise, A-weighted (1) THD Total harmonic distortion 0-dBFS input –85 –65 dB THD+N Total harmonic distortion + noise 0-dBFS input –82 –60 dB 87 dB Ripple on HPVDD (3.3 V) = 200 mVp-p at 1 kHz –62 dB 0.707 (2) Mute attenuation PSRR PO Power-supply rejection ratio (3) Maximum output power 80 Vrms 95 RL = 32 Ω, THD+N ≤ –60 dB 20 RL = 16 Ω, THD+N ≤ –60 dB 60 dB mW DAC LINEOUT (HP Driver in Lineout Mode) SNR Signal-to-noise ratio Measured as idle-channel noise, A-weighted 95 dB THD Total harmonic distortion 0-dBFS input, 0-dB gain –86 dB THD+N Total harmonic distortion + noise 0-dBFS input, 0-dB gain –83 dB DAC DIGITAL INTERPOLATION FILTER CHARACTERISTICS See Section 5.6.1.4 for DAC interpolation filter characteristics. DAC OUTPUT TO CLASS-D SPEAKER OUTPUT; LOAD = 4 Ω (DIFFERENTIAL), 50 pF SPKVDD = 3.6 V, BTL measurement, CM = 1.8 V, DAC input = 0 dBFS, class-D gain = 6 dB, THD ≤ –16.5 dB 2.3 SPKVDD = 3.6 V, BTL measurement, CM = 1.8 V, DAC input = –2 dBFS, class-D gain = 6 dB, THD ≤ –20 dB 2.1 Output, common-mode SPKVDD = 3.6 V, BTL measurement, DAC input = mute, CM = 1.8 V, class-D gain = 6 dB 1.8 V SNR Signal-to-noise ratio SPKVDD = 3.6 V, BTL measurement, class-D gain = 6 dB, measured as idle-channel noise, A-weighted (with respect to full-scale output value of 2.3 Vrms) 88 dB THD Total harmonic distortion SPKVDD = 3.6 V, BTL measurement, DAC input = –6 dBFS, CM = 1.8 V, class-D gain = 6 dB –65 dB THD+N Total harmonic distortion + noise SPKVDD = 3.6 V, BTL measurement, DAC input = –6 dBFS, CM = 1.8 V, class-D gain = 6 dB –63 dB PSRR Power-supply rejection ratio SPKVDD = 3.6 V, BTL measurement, ripple on SPKVDD = 200 mVp-p at 1 kHz –44 dB 110 dB Output voltage Mute attenuation PO (1) (2) (3) 6 Maximum output power Vrms SPKVDD = 3.6 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10% 1 SPKVDD = 4.3 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10% 1.5 SPKVDD = 5.5 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10% 2.5 W Ratio of output level with 1-kHz full-scale sine-wave input, to the output level with the inputs short-circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer. All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values. DAC to headphone-out PSRR measurement is calculated as PSRR = 20 X log(∆VHPL / ∆VHPVDD). ELECTRICAL SPECIFICATIONS Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Electrical Characteristics (continued) At 25°C, AVDD = HPVDD = IOVDD = 3.3 V, SPKVDD = 3.6 V, DVDD = 1.8 V, fS (audio) = 48 kHz, CODEC_CLKIN = 256 × fS, PLL = Off, VOL/MICDET pin disabled (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT DAC OUTPUT TO CLASS-D SPEAKER OUTPUT; LOAD = 8 Ω (DIFFERENTIAL), 50 pF SPKVDD = 3.6 V, BTL measurement, CM = 1.8 V, DAC input = 0 dBFS, class-D gain = 6 dB, THD ≤ –16.5 dB 2.2 SPKVDD = 3.6 V, BTL measurement, CM = 1.8 V, DAC input = –2 dBFS, class-D gain = 6 dB, THD ≤ –20 dB 2.1 Output, common-mode SPKVDD = 3.6 V, BTL measurement, DAC input = mute, CM = 1.8 V, class-D gain = 6 dB 1.8 V SNR Signal-to-noise ratio SPKVDD = 3.6 V, BTL measurement, class-D gain = 6 dB, measured as idle-channel noise, A-weighted (with respect to full-scale output value of 2.3 Vrms) 87 dB THD Total harmonic distortion SPKVDD = 3.6 V, BTL measurement, DAC input = –6 dBFS, CM = 1.8 V, class-D gain = 6 dB –67 dB THD+N Total harmonic distortion + noise SPKVDD = 3.6 V, BTL measurement, DAC input = –6 dBFS, CM = 1.8 V, class-D gain = 6 dB –66 dB PSRR Power-supply rejection ratio (1) SPKVDD = 3.6 V, BTL measurement, ripple on SPKVDD = 200 mVp-p at 1 kHz –44 dB 110 dB Output voltage Mute attenuation PO Maximum output power Output-stage leakage current for direct battery connection Vrms SPKVDD = 3.6 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10% 0.7 SPKVDD = 4.3 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10% 1 SPKVDD = 5.5 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10% 1.6 SPKVDD = 4.3 V, device is powered down (powerup-reset condition) 80 W nA DAC POWER CONSUMPTION DAC power consumption based per selected processing block, see Section 5.4 (1) DAC to speaker-out PSRR is a differential measurement calculated as PSRR = 20 × log(∆VSPK(P + M) / ∆VSPKVDD). ELECTRICAL SPECIFICATIONS Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 7 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Electrical Characteristics (continued) At 25°C, AVDD = HPVDD = IOVDD = 3.3 V, SPKVDD = 3.6 V, DVDD = 1.8 V, fS (audio) = 48 kHz, CODEC_CLKIN = 256 × fS, PLL = Off, VOL/MICDET pin disabled (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT DIGITAL INPUT/OUTPUT Logic family CMOS VIH VIL Logic level IIH = 5 μA, IOVDD ≥ 1.6 V 0.7 × IOVDD IIH = 5 μA, IOVDD < 1.6 V IOVDD IIL = 5 μA, IOVDD ≥ 1.6 V –0.3 IOH = 2 TTL loads VOL IOL = 2 TTL loads V 0 0.8 × IOVDD V 0.1 × IOVDD Capacitive load 3.4.1 0.3 × IOVDD IIL = 5 μA, IOVDD < 1.6 V VOH 3.4 V 10 V pF Timing Characteristics I2S/LJF/RJF Timing in Master Mode All specifications at 25°C, DVDD = 1.8 V Note: All timing specifications are measured at characterization but not tested at final test. WCLK tr td(WS) BCLK tf tS(DI) th(DI) DIN T0145-10 PARAMETER td(WS) ts(DI) th(DI) tr tf WCLK delay DIN setup DIN hold Rise time Fall time IOVDD = 1.1 V MIN MAX 45 8 8 25 25 IOVDD = 3.3 V MIN MAX 20 6 6 10 10 UNIT ns ns ns ns ns Figure 3-1. I2S/LJF/RJF Timing in Master Mode 8 ELECTRICAL SPECIFICATIONS Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com 3.4.2 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 I2S/LJF/RJF Timing in Slave Mode All specifications at 25°C, DVDD = 1.8 V Note: All timing specifications are measured at characterization but not tested at final test. WCLK tr th(WS) tS(WS) tH(BCLK) BCLK tL(BCLK) tf tS(DI) DIN th(DI) T0145-11 PARAMETER tH(BCLK) tL(BCLK) ts(WS) th(WS) ts(DI) th(DI) tr tf BCLK high period BCLK low period WCLK setup WCLK hold DIN setup DIN hold Rise time Fall time IOVDD = 1.1 V MIN MAX 35 35 8 8 8 8 4 4 IOVDD = 3.3 V MIN MAX 35 35 6 6 6 6 4 4 UNIT ns ns ns ns ns ns ns ns Figure 3-2. I2S/LJF/RJF Timing in Slave Mode ELECTRICAL SPECIFICATIONS Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 9 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 3.4.3 www.ti.com DSP Timing in Master Mode All specifications at 25°C, DVDD = 1.8 V Note: All timing specifications are measured at characterization but not tested at final test. WCLK td(WS) td(WS) tf BCLK tS(DI) tr DIN th(DI) T0146-09 PARAMETER td(WS) ts(DI) th(DI) tr tf WCLK delay DIN setup DIN hold Rise time Fall time IOVDD = 1.1 V MIN MAX 45 8 8 25 25 IOVDD = 3.3 V MIN MAX 20 8 8 10 10 UNIT ns ns ns ns ns Figure 3-3. DSP Timing in Master Mode 10 ELECTRICAL SPECIFICATIONS Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com 3.4.4 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 DSP Timing in Slave Mode All specifications at 25°C, DVDD = 1.8 V Note: All timing specifications are measured at characterization but not tested at final test. WCLK tS(WS) tS(WS) th(WS) th(WS) tf tL(BCLK) BCLK tr tS(DI) tH(BCLK) DIN th(DI) T0146-10 PARAMETER tH(BCLK) tL(BCLK) ts(WS) th(WS) ts(DI) th(DI) tr tf BCLK high period BCLK low period WCLK setup WCLK hold DIN setup DIN hold Rise time Fall time IOVDD = 1.1 V MIN MAX 35 35 8 8 8 8 4 4 IOVDD = 3.3 V MIN MAX 35 35 8 8 8 8 4 4 UNIT ns ns ns ns ns ns ns ns Figure 3-4. DSP Timing in Slave Mode ELECTRICAL SPECIFICATIONS Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 11 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 3.4.5 www.ti.com I2C Interface Timing All specifications at 25°C, DVDD = 1.8 V Note: All timing specifications are measured at characterization but not tested at final test. SDA tBUF tLOW tr tHIGH tf tHD;STA SCL tHD;STA tSU;DAT tHD;DAT STO tSU;STO tSU;STA STA STA STO T0295-02 PARAMETER fSCL tHD;STA tLOW tHIGH tSU;STA tHD;DAT tSU;DAT tr tf tSU;STO tBUF Cb SCL clock frequency Hold time (repeated) START condition. After this period, the first clock pulse is generated. LOW period of the SCL clock HIGH period of the SCL clock Setup time for a repeated START condition Data hold time: For I2C bus devices Data setup time SDA and SCL rise time SDA and SCL fall time Set-up time for STOP condition Bus free time between a STOP and START condition Capacitive load for each bus line Standard-Mode MIN TYP 0 4 MAX 100 4.7 4 4.7 0 250 Fast-Mode MIN TYP 0 0.8 UNITS MAX 400 μs μs μs 1.3 0.6 0.8 3.45 1000 300 4 4.7 400 0 100 20 + 0.1 Cb 20 + 0.1 Cb 0.8 1.3 kHz μs 300 300 μs ns ns ns μs μs 400 pF 0.9 Figure 3-5. I2C Interface Timing 12 ELECTRICAL SPECIFICATIONS Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 4 TYPICAL PERFORMANCE 4.1 DAC Performance TEXT ADDED FOR SPACING AMPLITUDE vs FREQUENCY AMPLITUDE vs FREQUENCY 0 0 AVDD = HPVDD = 3.3 V IOVDD = SPKVDD = 3.3 V DVDD = 1.8 V −20 −40 Amplitude − dBFS −40 Amplitude − dBFS AVDD = HPVDD = 3.3 V IOVDD = SPKVDD = 3.3 V DVDD = 1.8 V −20 −60 −80 −100 −60 −80 −100 −120 −120 −140 −140 −160 −160 0 5 10 15 20 0 5 f − Frequency − kHz 10 15 20 f − Frequency − kHz G001 G002 Figure 4-1. FFT - DAC to Line Output TEXT ADDED FOR SPACING Figure 4-2. FFT - DAC to Headphone Output TEXT ADDED FOR SPACING TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER THD+N − Total Harmonic Distortion + Noise − dB 0 −10 HPVDD = 2.7 V CM = 1.35 V −20 −30 −40 HPVDD = 3 V CM = 1.5 V −50 HPVDD = 3.3 V CM = 1.65 V −60 HPVDD = 3.6 V CM = 1.8 V −70 IOVDD = 3.3 V DVDD = 1.8 V Driver Gain = 9 dB RL = 16 Ω −80 −90 −100 0.00 0.02 0.04 0.06 0.08 0.10 0.12 PO − Output Power − W 0.14 G003 Figure 4-3. Headphone Output Power TYPICAL PERFORMANCE Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 13 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 4.2 www.ti.com Class-D Speaker Driver Performance TEXT ADDED FOR SPACING TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER 0 AVDD = HPVDD = 3.3 V IOVDD = 3.3 V SPKVDD = 5.5 V DVDD = 1.8 V RL = 4 Ω −10 −20 Driver Gain = 24 dB −30 Driver Gain = 18 dB −40 Driver Gain = 12 dB −50 Driver Gain = 6 dB −60 −70 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 PO − Output Power − W SPKVDD = 3.3 V THD+N − Total Harmonic Distortion + Noise − dB THD+N − Total Harmonic Distortion + Noise − dB 0 −10 −20 SPKVDD = 3.6 V −30 SPKVDD = 4.3 V SPKVDD = 5.5 V −40 AVDD = 3.3 V HPVDD = 3.3 V IOVDD = 3.3 V DVDD = 1.8 V Driver Gain = 18 dB RL = 4 Ω −50 −60 −70 0.0 4.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 PO − Output Power − W G004 G005 Figure 4-4. Max Class-D Speaker-Driver Output Power (RL = 4 Ω) TEXT ADDED FOR SPACING Figure 4-5. Class-D Speaker-Driver Output Power (RL = 4 Ω) TEXT ADDED FOR SPACING TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER −10 −20 0 AVDD = HPVDD = 3.3 V IOVDD = 3.3 V SPKVDD = 5.5 V DVDD = 1.8 V RL = 8 Ω Driver Gain = 18 dB −30 −40 Driver Gain = 24 dB Driver Gain = 12 dB −50 Driver Gain = 6 dB −60 −70 0.0 THD+N − Total Harmonic Distortion + Noise − dB THD+N − Total Harmonic Distortion + Noise − dB 0 0.5 1.0 1.5 PO − Output Power − W 2.0 2.5 −20 SPKVDD = 3.6 V −30 SPKVDD = 4.3 V SPKVDD = 5.5 V −40 AVDD = 3.3 V HPVDD = 3.3 V IOVDD = 3.3 V DVDD = 1.8 V Driver Gain = 18 dB RL = 8 Ω −50 −60 −70 0.0 0.5 1.0 1.5 2.0 PO − Output Power − W G006 Figure 4-6. Max Class-D Speaker-Driver Output Power (RL = 8 Ω) 14 SPKVDD = 3.3 V −10 2.5 3.0 G007 Figure 4-7. Class-D Speaker-Driver Output Power (RL = 8 Ω) TYPICAL PERFORMANCE Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com 4.3 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Analog Bypass Performance TEXT ADDED FOR SPACING AMPLITUDE vs FREQUENCY AMPLITUDE vs FREQUENCY 0 0 AVDD = HPVDD = 3.3 V IOVDD = SPKVDD = 3.3 V DVDD = 1.8 V −20 −40 Amplitude − dBFS −40 Amplitude − dBFS AVDD = HPVDD = 3.3 V IOVDD = SPKVDD = 3.3 V DVDD = 1.8 V −20 −60 −80 −100 −60 −80 −100 −120 −120 −140 −140 −160 −160 0 5 10 15 20 0 f − Frequency − kHz 5 10 15 20 f − Frequency − kHz G008 Figure 4-8. FFT - Line In Bypass to Line Output G009 Figure 4-9. FFT - Line In Bypass to Headphone Output TYPICAL PERFORMANCE Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 15 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 4.4 www.ti.com MICBIAS Performance TEXT ADDED FOR SPACING VOLTAGE vs CURRENT 3.5 3.0 Micbias = AVDD (3.3 V) V − Voltage − V 2.5 Micbias = 2.5 V 2.0 Micbias = 2 V 1.5 1.0 0.5 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 I − Current − mA G010 Figure 4-10. MICBIAS 16 TYPICAL PERFORMANCE Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5 APPLICATION INFORMATION 5.1 Typical Circuit Configuration +3.3VA SVDD 0.1 mF 22 mF 0.1 mF 22 mF SPKVDD SPKVDD 0.1 mF SPKVSS SPKVSS 0.1 mF 10 mF HPVDD AVDD 10 mF AVSS HPVSS GPIO1 SDA Host Processor SCL MCLK SPKP SPKP WCLK SPKM SPKM 8-W or 4-W Speaker SDIN BCLK TLV320DAC3120 RESET To External MIC Circuitry Analog In MICBIAS HPL AIN1 HPR Stereo Headphone Out AIN2 AVDD R1 34.8 kW P1 25 kW VOL/MICDET DVDD DVSS IOVDD IOVSS 1 mF R2 9.76 kW +1.8VD AVSS 0.1 mF IOVDD 10 mF 0.1 mF 10 mF S0400-06 Figure 5-1. Typical Circuit Configuration APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 17 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.2 www.ti.com Overview The TLV320DAC3120 is a highly integrated mono audio DAC for portable computing, communication, and entertainment applications. A register-based architecture eases integration with microprocessor-based systems through standard serial-interface buses. This device contains a two-wire I2C bus interface, which allows full register access. All peripheral functions are controlled through these registers and the onboard state machines. The TLV320DAC3120 consists of the following blocks: • miniDSP digital signal-processing block • Audio DAC • Dynamic range compressor (DRC) • Mono headphone/lineout amplifier • Class-D mono amplifier capable of driving 4-Ω or 8-Ω speakers • Pin-controlled or register-controlled volume level • Power-down de-pop and power-up soft start • Analog inputs • I2C control interface • Power-down control block Following a toggle of the RESET pin or a software reset, the device operates in the default mode. The I2C interface is used to write to the control registers to configure the device. The I2C address assigned to the TLV320DAC3120 is 001 1000. This device always operates in an I2C slave mode. All registers are 8-bit, and all writable registers have readback capability. The device autoincrements to support sequential addressing and can be used with I2C fast mode. Once the device is reset, all appropriate registers are updated by the host processor to configure the device as needed by the user. 5.2.1 Device Initialization 5.2.1.1 Reset The TLV320DAC3120 internal logic must be initialized to a known condition for proper device function. To initialize the device to its default operating condition, the hardware reset pin (RESET) must be pulled low for at least 10 ns. For this initialization to work, both the IOVDD and DVDD supplies must be powered up. It is recommended that while the DVDD supply is being powered up, the RESET pin be pulled low. The device can also be reset via software reset. Writing a 1 into page 0 / register 1, bit D0 resets the device. 5.2.1.2 Device Start-Up Lockout Times After the TLV320DAC3120 is initialized through hardware reset at power-up or software reset, the internal memories are initialized to default values. This initialization takes place within 1 ms after pulling the RESET signal high. During this initialization phase, no register-read or register-write operation should be performed on the DAC coefficient buffers. Also, no block within the codec should be powered up during the initialization phase. 5.2.1.3 PLL Start-Up Whenever the PLL is powered up, a start-up delay of approximately of 10 ms occurs after the power-up command of the PLL and before the clocks are available to the codec. This delay is to ensure stable operation of the PLL and clock-divider logic. 18 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com 5.2.1.4 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Power-Stage Reset The power-stage-only reset is used to reset the device after an overcurrent latching shutdown has occurred. Using this reset re-enables the output stage without resetting all of the registers in the device. Each of the two power stages has its own dedicated reset bit. The headphone power-stage reset is performed by setting page 1 / register 31, bit D7 for HPOUT. The speaker power-stage reset is performed by setting page 1 / register 32, bit D7 for SPKP and SPKM. 5.2.1.5 Software Power Down By default, all circuit blocks are powered down following a reset condition. Hardware power up of each circuit block can be controlled by writing to the appropriate control register. This approach allows the lowest power-supply current for the functionality required. However, when a block is powered down, all of the register settings are maintained as long as power is still being applied to the device. 5.2.2 Audio Analog I/O The TLV320DAC3120 features a mono audio DAC. It supports a wide range of analog interfaces to support different headsets and analog outputs. The TLV320DAC3120 interfaces to output drivers (8-Ω, 16Ω, 32-Ω). 5.3 miniDSP The TLV320DAC3120 features a miniDSP core which is tightly coupled to the DAC. The fully programmable algorithms for the miniDSP must be loaded into the device after power up. The miniDSP has direct access to the digital stereo audio stream, offering the possibility for advanced, very low-groupdelay DSP algorithms. The miniDSP has 1024 programmable instructions, 896 data memory locations, and 512 programmable coefficients (in the adaptive mode, each bank has 256 programmable coefficients). 5.3.1 Software Software development for the TLV320DAC3120 is supported through TI's comprehensive PurePath™ Studio software development environment, a powerful, easy-to-use tool designed specifically to simplify software development on Texas Instruments miniDSP audio platforms. The graphical development environment consists of a library of common audio functions that can be dragged and dropped into an audio signal flow and graphically connected together. The DSP code can then be assembled from the graphical signal flow with the click of a mouse. See the TLV320DAC3120 product folder on www.ti.com to learn more about PurePath Studio and the latest status on available, ready-to-use DSP algorithms. 5.4 Digital Processing Low-Power Modes The TLV320DAC3120 device can be tuned to minimize power dissipation, to maximize performance, or to an operating point between the two extremes to best fit the application. The choice of processing blocks, PRB_P4 to PRB_P22 for mono playback and PRB_R4 to PRB_R18 for mono recording, also influences the power consumption. In fact, the numerous processing blocks have been implemented to offer a choice among configurations having a different balance of power-optimization and signal-processing capabilities. APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 19 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.4.1 www.ti.com DAC Playback on Headphones, Mono, 48 kHz, DVDD = 1.8 V, AVDD = 3.3 V, HPVDD = 3.3 V DOSR = 128, Processing Block = PRB_P12 (Interpolation Filter B) Power consumption = 15.4 mW Table 5-1. PRB_P12 Alternative Processing Blocks, 15.4 mW Processing Block Filter Estimated Power Change (mW) PRB_P4 A 0.57 PRB_P5 A 1.48 PRB_P6 A 1.08 PRB_P13 B 0.56 PRB_P14 B 0.27 PRB_P15 B 0.89 PRB_P16 B 0.31 DOSR = 64, Processing Block = PRB_P12 (Interpolation Filter B) Power consumption = 15.54 mW Table 5-2. PRB_P12 Alternative Processing Blocks, 15.54 mW 5.4.2 Processing Block Filter Estimated Power Change (mW) PRB_P4 A 0.37 PRB_P5 A 1.23 PRB_P6 A 1.15 PRB_P13 B 0.43 PRB_P14 B 0.13 PRB_P15 B 0.85 PRB_P16 B 0.21 DAC Playback on Headphones, Mono, 8 kHz, DVDD = 1.8 V, AVDD = 3.3 V, HPVDD = 3.3 V DOSR = 768, Processing Block = PRB_P12 (Interpolation Filter B) Power consumption = 14.49 mW Table 5-3. PRB_P12 Alternative Processing Blocks, 14.49 mW 20 Processing Block Filter Estimated Power Change (mW) PRB_P4 A –0.04 PRB_P5 A 0.2 PRB_P6 A –0.01 PRB_P13 B 0.1 PRB_P14 B 0.05 PRB_P15 B –0.03 PRB_P16 B 0.07 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 DOSR = 384, Processing Block = PRB_P12 (Interpolation Filter B) Power consumption = 14.42 mW Table 5-4. PRB_P12 Alternative Processing Blocks, 14.42 mW 5.5 Processing Block Filter Estimated Power Change (mW) PRB_P4 A 0.16 PRB_P5 A 0.3 PRB_P6 A 0.2 PRB_P13 B 0.15 PRB_P14 B 0.07 PRB_P15 B 0.18 PRB_P16 B 0.09 Analog Signals The TLV320DAC3120 analog signals consist of: • Microphone bias (MICBIAS) • Analog inputs AIN1 and AIN2, which can be used to pass-through or mix analog signals to output stages • Analog outputs class-D speaker driver and headphone/lineout driver providing output capability for the DAC, AIN1, AIN2, or a mix of the three 5.5.1 MICBIAS The TLV320DAC3120 includes a microphone bias circuit which can source up to 4 mA of current, and is programmable to a 2-V, 2.5-V, or AVDD level. The level can be controlled by writing to page 1 / register 46, bits D1–D0. This functionality is shown in Table 5-5. Table 5-5. MICBIAS Settings D1 D0 FUNCTIONALITY 0 0 MICBIAS output is powered down. 0 1 MICBIAS output is powered to 2 V. 1 0 MICBIAS output is powered to 2.5 V. 1 1 MICBIAS output is powered to AVDD. During normal operation, MICBIAS can be set to 2.5 V for better performance. However, depending on the model of microphone that is selected, optimal performance might be obtained at another setting, so the performance at a given setting should be verified. The lowest current consumption occurs when MICBIAS is powered down. The next-lowest current consumption occurs when MICBIAS is set at AVDD. 5.5.2 Analog Inputs AIN1 and AIN2 AIN1 (pin 13) and AIN2 (pin 14) are inputs to the output mixer along with the DAC output. Page 1 / register 35 provides control signals for determining the signals routed through the output mixer. The output of the output mixer then can be attenuated or amplified through the class-D and/or headphone/lineout drivers. APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 21 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.6 www.ti.com Audio DAC and Audio Analog Outputs The mono audio DAC consists of a digital audio processing block, a digital interpolation filter, a digital delta-sigma modulator, and an analog reconstruction filter. The high oversampling ratio (normally DOSR is between 32 and 128) exhibits good dynamic range by ensuring that the quantization noise generated within the delta-sigma modulator stays outside of the audio frequency band. Audio analog outputs include mono headphone/lineout and mono class-D speaker outputs. Because the TLV320DAC3120 contains a mono DAC, it inputs the mono data from the left channel, the right channel, or a mix of the left and right channels as [(L + R) ÷ 2], selected by page 0 / register 63, bits D5–D4. See Figure 1-1 for the signal flow. 5.6.1 DAC The TLV320DAC3120 mono audio DAC supports data rates from 8 kHz to 192 kHz. The audio channel of the mono DAC consists of a signal-processing engine with fixed processing blocks, a programmable miniDSP, a digital interpolation filter, multibit digital delta-sigma modulator, and an analog reconstruction filter. The DAC is designed to provide enhanced performance at low sampling rates through increased oversampling and image filtering, thereby keeping quantization noise generated within the delta-sigma modulator and observed in the signal images strongly suppressed within the audio band to beyond 20 kHz. To handle multiple input rates and optimize power dissipation and performance, the TLV320DAC3120 allows the system designer to program the oversampling rates over a wide range from 1 to 1024 by configuring page 0 / register 13 and page 0 / register 14. The system designer can choose higher oversampling ratios for lower input data rates and lower oversampling ratios for higher input data rates. The TLV320DAC3120 DAC channel includes a built-in digital interpolation filter to generate oversampled data for the delta-sigma modulator. The interpolation filter can be chosen from three different types, depending on required frequency response, group delay, and sampling rate. DAC power up is controlled by writing to page 0 / register 63, bit D7 for the mono channel. The monochannel DAC clipping flag is provided as a read-only bit on page 0 / register 39, bit D7. 5.6.1.1 DAC Processing Blocks The TLV320DAC3120 implements signal-processing capabilities and interpolation filtering via processing blocks. These fixed processing blocks give users the choice of how much and what type of signal processing they may use and which interpolation filter is applied. The choices among these processing blocks allows the system designer to balance power conservation and signal-processing flexibility. Table 5-6 gives an overview of all available processing blocks of the DAC channel and their properties. The resource-class column gives an approximate indication of power consumption for the digital (DVDD) supply; however, based on the out-of-band noise spectrum, the analog power consumption of the drivers (HPVDD) may differ. The signal-processing blocks available are: • First-order IIR • Scalable number of biquad filters The processing blocks are tuned for common cases and can achieve high image rejection or low group delay in combination with various signal-processing effects such as audio effects and frequency shaping. The available first-order IIR and biquad filters have fully user-programmable coefficients. 22 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 5-6. Overview – DAC Predefined Processing Blocks Processing Block No. Interpolation Filter Channel First-Order IIR Available Number of Biquads PRB_P4 A PRB_P5 A DRC Resource Class Mono No Mono Yes 3 No 4 6 Yes 6 PRB_P6 A Mono Yes 6 No 6 PRB_P12 B Mono Yes 0 No 3 PRB_P13 B Mono No 4 Yes 4 PRB_P14 B Mono No 4 No 4 PRB_P15 B Mono Yes 6 Yes 6 PRB_P16 B Mono Yes 6 No 4 PRB_P20 C Mono Yes 0 No 2 PRB_P21 C Mono Yes 4 Yes 3 PRB_P22 C Mono Yes 4 No 2 PRB_P25 A Mono Yes 5 Yes 12 5.6.1.2 DAC Processing Blocks – Signal Chain Details 5.6.1.2.1 Three Biquads, Filter A BiQuad A BiQuad B from Interface BiQuad C Interp. Filter A ´ to Modulator Digital Volume Ctrl Figure 5-2. Signal Chain for PRB_P4 5.6.1.2.2 Six Biquads, First-Order IIR, DRC, Filter A or B IIR from Interface BiQuad A BiQuad B BiQuad C BiQuad D BiQuad E Interp. Filter A,B BiQuad F HPF ´ to Modulator Digital Volume Ctrl DRC Figure 5-3. Signal Chain for PRB_P5 and PRB_P15 5.6.1.2.3 Six Biquads, First-Order IIR, Filter A or B IIR from Interface BiQuad A BiQuad B BiQuad C BiQuad D BiQuad E BiQuad F Interp. Filter A,B ´ to Modulator Digital Volume Ctrl Figure 5-4. Signal Chain for PRB_P6 and PRB_P16 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 23 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com 5.6.1.2.4 IIR, Filter B or C Interp. Filter B,C IIR from Interface to Modulator ´ Digital Volume Ctrl Figure 5-5. Signal Chain for PRB_P12 and PRB_P20 5.6.1.2.5 Four Biquads, DRC, Filter B from Interface BiQuad A BiQuad B BiQuad C Interp. Filter B BiQuad D HPF ´ to Modulator Digital Volume Ctrl DRC Figure 5-6. Signal Chain for PRB_P13 5.6.1.2.6 Four Biquads, Filter B BiQuad A from Interface BiQuad B BiQuad C BiQuad D Interp. Filter B ´ to Modulator Digital Volume Ctrl Figure 5-7. Signal Chain for PRB_P14 5.6.1.2.7 Four Biquads, First-Order IIR, DRC, Filter C BiQuad A IIR BiQuad B BiQuad C BiQuad D Interp. Filter C ´ from Interface HPF to Modulator Digital Volume Ctrl DRC Figure 5-8. Signal Chain for PRB_P21 5.6.1.2.8 Four Biquads, First-Order IIR, Filter C IIR from Interface BiQuad A BiQuad B BiQuad C BiQuad D Interp. Filter C ´ to modulator Digital Volume Ctrl Figure 5-9. Signal Chain for PRB_P22 24 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.6.1.2.9 Five Biquads, DRC, Beep Generator, Filter A from Interface IIR BiQuad B BiQuad C BiQuad D BiQuad E BiQuad F HPF Interp. Filter A ´ + to Modulator Digital Volume Ctrl Beep Volume Ctrl ´ DRC Beep Gen. Figure 5-10. Signal Chain for PRB_P25 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 25 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.6.1.3 www.ti.com DAC User-Programmable Filters Depending on the selected processing block, different types and orders of digital filtering are available. Up to six biquad sections are available for specific processing blocks. The coefficients of the available filters are arranged as sequentially-indexed coefficients in two banks. If adaptive filtering is chosen, the coefficient banks can be switched in real time. When the DAC is running, the user-programmable filter coefficients are locked and cannot be accessed for either read or write. However, the TLV320DAC3120 offers an adaptive filter mode as well. Setting page 8 / register 1, bit D2 = 1 turns on double buffering of the coefficients. In this mode, filter coefficients can be updated through the host and activated without stopping and restarting the DAC. This enables advanced adaptive filtering applications. In the double-buffering scheme, all coefficients are stored in two buffers (buffers A and B). When the DAC is running and adaptive filtering mode is turned on, setting page 8 / register 1, bit D0 = 1 switches the coefficient buffers at the next start of a sampling period. This bit is set back to 0 after the switch occurs. At the same time, page 8 / register 1, bit D1 toggles. The flag in page 8 / register 1, bit D1 indicates which of the two buffers is actually in use. Page 8 / register 1, bit D1 = 0: buffer A is in use by the DAC engine; bit D1 = 1: buffer B is in use. While the device is running, coefficient updates are always made to the buffer not in use by the DAC, regardless of the buffer to which the coefficients have been written. Table 5-7. Adaptive-Mode Filter-Coefficient Buffer Switching DAC Powered Up Page 8, Reg 1, Bit D1 Coefficient Buffer in Use I2C Writes to Updates No 0 None Page 8, Reg 2–3, buffer A Page 8, Reg 2–3, buffer A No 0 None Page 12, Reg 2–3, buffer B Yes 0 Buffer A Page 8, Reg 2–3, buffer A Page 12, Reg 2–3, buffer B Yes 0 Buffer A Page 12, Reg 2–3, buffer B Yes 1 Buffer B Page 8, Reg 2–3, buffer A Page 8, Reg 2–3, buffer A Yes 1 Buffer B Page 12, Reg 2–3, buffer B Page 12, Reg 2–3, buffer B Page 12, Reg 2–3, buffer B Page 8, Reg 2–3, buffer A The user-programmable coefficients for the DAC processing blocks are defined on pages 8 and 9 for buffer A and pages 12 and 13 for buffer B. The coefficients of these filters are each 16-bit, 2s-complement format, occupying two consecutive 8-bit registers in the register space. Specifically, the filter coefficients are in 1.15 (one dot 15) format with a range from –1.0 (0x8000) to 0.999969482421875 (0x7FFF) as shown in Figure 5-11. 2 –15 2 2 –4 –1 Bit Bit Largest Positive Number: = 0.111111111111111111 = 0.999969482421875 = 1.0 – 1 LSB Bit Largest Negative Number: = 1.000010000100001000 = 0x8000 = –1.0 (by definition) Fraction Point Sign Bit S...xxxxxxxxxxxxxxxxxx Figure 5-11. 26 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.6.1.3.1 First-Order IIR Section The IIR is of first order and its transfer function is given by H(z) = N0 + N1z -1 215 - D1z -1 (1) The frequency response for the first-order IIR section with default coefficients is flat. Table 5-8. DAC IIR Filter Coefficients Filter DAC Coefficient, Mono Channel Filter Coefficient First-order IIR Default (Reset) Values N0 Page 9 / registers 2–3 0x7FFF (decimal 1.0 – LSB value) N1 Page 9 / registers 4–5 0x0000 D1 Page 9 / registers 6–7 0x0000 5.6.1.3.2 Biquad Section The transfer function of each of the biquad filters is given by H(z) = N0 + 2 ´ N1z -1 + N2 z -2 215 - 2 ´ D1z -1 - D2 z -2 (2) Table 5-9. DAC Biquad Filter Coefficients Filter Biquad A Biquad B Biquad C Biquad D Biquad E Coefficient Mono DAC Channel Default (Reset) Values N0 Page 8 / registers 2–3 0x7FFF (decimal 1.0 – LSB value) N1 Page 8 / registers 4–5 0x0000 N2 Page 8 / registers 6–7 0x0000 D1 Page 8 / registers 8–9 0x0000 D2 Page 8 / registers 10–11 0x0000 N0 Page 8 / registers 12–13 0x7FFF (decimal 1.0 – LSB value) N1 Page 8 / registers 14–15 0x0000 N2 Page 8 / registers 16–17 0x0000 D1 Page 8 / registers 18–19 0x0000 D2 Page 8 / registers 20–21 0x0000 N0 Page 8 / registers 22–23 0x7FFF (decimal 1.0 – LSB value) N1 Page 8 / registers 24–25 0x0000 N2 Page 8 / registers 26–27 0x0000 D1 Page 8 / registers 28–29 0x0000 D2 Page 8 / registers 30–31 0x0000 N0 Page 8 / registers 32–33 0x7FFF (decimal 1.0 – LSB value) N1 Page 8 / registers 34–35 0x0000 N2 Page 8 / registers 36–37 0x0000 D1 Page 8 / registers 38–39 0x0000 D2 Page 8 / registers 40–41 0x0000 N0 Page 8 / registers 42–43 0x7FFF (decimal 1.0 – LSB value) N1 Page 8 / registers 44–45 0x0000 N2 Page 8 / registers 46–47 0x0000 D1 Page 8 / registers 48–49 0x0000 D2 Page 8 / registers 50–51 0x0000 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 27 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 5-9. DAC Biquad Filter Coefficients (continued) Filter Coefficient Biquad F 5.6.1.4 Mono DAC Channel Default (Reset) Values N0 Page 8 / registers 52–53 0x7FFF (decimal 1.0 – LSB value) N1 Page 8 / registers 54–55 0x0000 N2 Page 8 / registers 56–57 0x0000 D1 Page 8 / registers 58–59 0x0000 D2 Page 8 / registers 60–61 0x0000 DAC Interpolation Filter Characteristics 5.6.1.4.1 Interpolation Filter A Filter A is designed for an fS up to 48 ksps with a flat pass band of 0 kHz–20 kHz. Table 5-10. Specification for DAC Interpolation Filter A Parameter Condition Value (Typical) Unit Filter-gain pass band 0 … 0.45 fS ±0.015 dB Filter-gain stop band 0.55 fS… 7.455 fS –65 dB 21/fS s Filter group delay DAC Channel Response for Interpolation Filter A (Red Line Corresponds to –65 dB) 0 –10 Magnitude – dB –20 –30 –40 –50 –60 –70 –80 –90 1 2 5 6 3 4 Frequency Normalized to fS 7 Figure 5-12. Frequency Response of DAC Interpolation Filter A 5.6.1.4.2 Interpolation Filter B Filter B is specifically designed for an fS up to 96 ksps. Thus, the flat pass-band region easily covers the required audio band of 0 kHz–20 kHz. Table 5-11. Specification for DAC Interpolation Filter B Parameter Condition Value (Typical) Unit Filter-gain pass band 0 … 0.45 fS ±0.015 dB Filter-gain stop band 0.55 fS … 3.45 fS –58 dB 18/fS s Filter group delay 28 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 DAC Channel Response for Interpolation Filter B (Red Line Corresponds to –58 dB) 0 Magnitude – dB –10 –20 –30 –40 –50 –60 –70 –80 0.5 1 1.5 2 2.5 Frequency Normalized to fS 3 3.5 Figure 5-13. Frequency Response of Channel Interpolation Filter B 5.6.1.4.3 Interpolation Filter C Filter C is specifically designed for the 192-ksps mode. The pass band extends up to 0.4 × fS (corresponds to 80 kHz), more than sufficient for audio applications. DAC Channel Response for Interpolation Filter C (Red Line Corresponds to –43 dB) 0 Magnitude – dB –10 –20 –30 –40 –50 –60 –70 0 0.2 0.4 0.6 0.8 1 1.2 Frequency Normalized to fS 1.4 Figure 5-14. Frequency Response of DAC Interpolation Filter C Table 5-12. Specification for DAC Interpolation Filter C Parameter Condition Value (Typical) Unit Filter-gain pass band 0 … 0.35 fS ±0.03 dB Filter-gain stop band 0.6 fS … 1.4 fS –43 dB 13/fS s Filter group delay APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 29 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.6.2 www.ti.com DAC Digital-Volume Control The DAC has a digital volume-control block which implements programmable gain. Each channel has an independent volume control that can be varied from 24 dB to –63.5 dB in 0.5-dB steps. The mono-channel DAC volume can be controlled by writing to page 0 / register 65, bits D7–D0. DAC muting and setting up a master gain control to control the mono channel is done by writing to page 0 / register 64, bits D3 and D1. The gain is implemented with a soft-stepping algorithm, which only changes the actual volume by 0.125 dB per input sample, either up or down, until the desired volume is reached. The rate of softstepping can be slowed to one step per two input samples by writing to page 0 / register 63, bits D1–D0. Note that the default source for volume-control level settings is controlled by register writes to page 0 / register 65. Use of the VOL/MICDET pin to control the DAC volume is ignored until the volume-control source selected has been changed to pin control (page 0 / register 116, bit D7 = 1). This functionality is shown in Figure 1-1. During soft-stepping, the host does not receive a signal when the DAC has been completely muted. This may be important if the host must mute the DAC before making a significant change, such as changing sample rates. In order to help with this situation, the device provides a flag back to the host via a readonly register, page 0 / register 38, bit D4 for the mono channel. This information alerts the host when the part has completed the soft-stepping, and the actual volume has reached the desired volume level. The soft-stepping feature can be disabled by writing to page 0 / register 63, bits D1–D0. If soft-stepping is enabled, the CODEC_CLKIN signal should be kept active until the DAC power-up flag is cleared. When this flag is cleared, the internal DAC soft-stepping process is complete, and CODEC_CLKIN can be stopped if desired. (The analog volume control can be ramped down using an internal oscillator.) 5.6.3 Volume-Control Pin The range of voltages used by the 7-bit SAR ADC is shown in the Electrical Characteristics table. The volume-control pin is not enabled by default, but it can be enabled by writing 1 to page 0 / register 116, bit D7. The default DAC volume control uses software control of the volume, which occurs if page 0 / register 116, bit D7 = 0. Soft-stepping the volume level is set up by writing to page 0 / register 63, bits D1–D0. When the volume-pin function is used, a 7-bit Vol ADC reads the voltage on the VOL/MICDET pin and updates the digital volume control. (It overwrites the current value of the volume control.) The new volume setting which has been applied due to a change of voltage on the volume control pin can be read on page 0 / register 117, bits D6–D0. The 7-bit Vol ADC clock source can be selected on page 0 / register 116, bit D6. The update rate can be programmed on page 0 / register 116, bits D2–D0 for this 7bit SAR ADC. The VOL/MICDET pin gain mapping is shown in Table 5-13. Table 5-13. VOL/MICDET Pin Gain Mapping VOL/MICDET PIN SAR OUTPUT 30 DIGITAL GAIN APPLIED 0 18 dB 1 17.5 dB 2 17 dB : : 35 0.5 dB 36 0.0 dB 37 –0.5 dB : : 89 –26.5 dB APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 5-13. VOL/MICDET Pin Gain Mapping (continued) VOL/MICDET PIN SAR OUTPUT DIGITAL GAIN APPLIED 90 –27 dB 91 –28 dB : : 125 –62 dB 126 –63 dB 127 Mute The VOL/MICDET pin connection and functionality are shown in Figure 1-1. As shown in Table 5-13, the VOL/MICDET pin has a range of volume control from 18 dB down to –63 dB, and mute. However, if less maximum gain is required, then a smaller range of voltage should be applied to the VOL/MICDET pin. This can be done by increasing the value of R2 relative to the value of (P1 + R1), so that more voltage is available at the bottom of P1. The circuit should also be designed such that for the values of R1, R2, and P1 chosen, the maximum voltage (top of the potentiometer) does not exceed AVDD/2 (see Figure 5-1). The recommended values for R1, R2, and P1 for several maximum gains are shown in Table 5-14. Note that In typical applications, R1 should not be 0 Ω, as the VOL/MICDET pin should not exceed AVDD/2 for proper ADC operation. Table 5-14. VOL/MICDET Pin Gain Scaling 5.6.4 ADC VOLTAGE for AVDD = 3.3 V (V) DIGITAL GAIN RANGE (dB) 0 0 V to 1.65 V 18 dB to –63 dB 7.68 0.386 V to 1.642 V 3 dB to –63 dB 0.463 V to 1.649 V 0 dB to –63 dB R1 (kΩ) P1 (kΩ) R2 (kΩ) 25 25 33 25 34.8 25 9.76 Dynamic Range Compression Typical music signals are characterized by crest factors, the ratio of peak signal power to average signal power, of 12 dB or more. To avoid audible distortions due to clipping of peak signals, the gain of the DAC channel must be adjusted so as not to cause hard clipping of peak signals. As a result, during nominal periods, the applied gain is low, causing the perception that the signal is not loud enough. To overcome this problem, DRC in the TLV320DAC3120 continuously monitors the output of the DAC digital volume control to detect its power level relative to 0 dBFS. When the power level is low, DRC increases the input signal gain to make it sound louder. At the same time, if a peaking signal is detected, it autonomously reduces the applied gain to avoid hard clipping. This results in sounds more pleasing to the ear as well as sounding louder during nominal periods. The DRC functionality in the TLV320DAC3120 is implemented by a combination of processing blocks in the DAC channel as described in Section 5.6.1.2. DRC can be disabled by writing to page 0 / register 68, bits D6–D5. DRC typically works on the filtered version of the input signal. The input signals have no audio information at dc and extremely low frequencies; however, they can significantly influence the energy estimation function in DRC. Also, most of the information about signal energy is concentrated in the low-frequency region of the input signal. To estimate the energy of the input signal, the signal is first fed to the DRC high-pass filter and then to the DRC low-pass filter. These filters are implemented as first-order IIR filters given by HHPF (z) = N0 + N1z -1 215 - D1z -1 (3) APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 31 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 HLPF (z) = www.ti.com N0 + N1z -1 215 - D1z -1 (4) The coefficients for these filters are 16 bits wide in 2s-complement format and are user-programmable through register write as given in Table 5-15. 32 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 5-15. DRC HPF and LPF Coefficients Coefficient Location HPF N0 C71 page 9 / registers 14 to 15 HPF N1 C72 page 9 / registers 16 to 17 HPF D1 C73 page 9 / registers 18 to 19 LPF N0 C74 page 9 / registers 20 to 21 LPF N1 C75 page 9 / registers 22 to 23 LPF D1 C76 page 9 / registers 24 to 25 The default values of these coefficients implement a high-pass filter with a cutoff at 0.00166 × DAC_fS, and a low-pass filter with a cutoff at 0.00033 × DAC_fS. The output of the DRC high-pass filter is fed to the processing block selected for the DAC channel. The absolute value of the DRC-LPF filter is used for energy estimation within the DRC. The gain in the DAC digital volume control is controlled by page 0 / registers 65 and 66. When the DRC is enabled, the applied gain is a function of the digital volume-control register setting and the output of the DRC. The DRC parameters are described in sections that follow. 5.6.4.1 DRC Threshold The DRC threshold represents the level of the DAC playback signal at which the gain compression becomes active. The output of the digital volume control in the DAC is compared with the set threshold. The threshold value is programmable by writing to page 0 / register 68, bits D4–D2. The threshold value can be adjusted between –3 dBFS and –24 dBFS in steps of 3 dB. Keeping the DRC threshold value too high may not leave enough time for the DRC block to detect peaking signals, and can cause excessive distortion at the outputs. Keeping the DRC threshold value too low can limit the perceived loudness of the output signal. The recommended DRC threshold value is –24 dB. When the output signal exceeds the set DRC threshold, the interrupt flag bits at page 0 / register 44, bits D3–D2 are updated. These flag bits are sticky in nature, and are reset only after they are read back by the user. The non-sticky versions of the interrupt flags are also available at page 0 / register 46, bits D3–D2. 5.6.4.2 DRC Hysteresis DRC hysteresis is programmable by writing to page 0 / register 68, bits D1–D0. These bits can be programmed to represent values between 0 dB and 3 dB in steps of 1 dB. It is a programmable window around the programmed DRC threshold that must be exceeded for disabled DRC to become enabled, or enabled DRC to become disabled. For example, if the DRC threshold is set to –12 dBFS and the DRC hysteresis is set to 3 dB, then if the gain compression in DRC is inactive, the output of the DAC digital volume control must exceed –9 dBFS before gain compression due to the DRC is activated. Similarly, when the gain compression in the DRC is active, the output of the DAC digital volume control must fall below –15 dBFS for gain compression in the DRC to be deactivated. The DRC hysteresis feature prevents the rapid activation and de-activation of gain compression in DRC in cases when the output of the DAC digital volume control rapidly fluctuates in a narrow region around the programmed DRC threshold. By programming the DRC hysteresis as 0 dB, the hysteresis action is disabled. The recommended value of DRC hysteresis is 3 dB. 5.6.4.3 DRC Hold Time DRC hold time is intended to slow the start of decay for a specified period of time in response to a decrease in energy level. To minimize audible artifacts, it is recommended to set the DRC hold time to 0 through programming page 0 / register 69, bits D6–D3 = 0000. APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 33 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.6.4.4 www.ti.com DRC Attack Rate When the output of the DAC digital volume control exceeds the programmed DRC threshold, the gain applied in the DAC digital volume control is progressively reduced to prevent the signal from saturating the channel. This process of reducing the applied gain is called attack. To avoid audible artifacts, the gain is reduced slowly with a rate equaling the attack rate, programmable via page 0 / register 70, bits D7–D4. Attack rates can be programmed from 4-dB gain change per sample period to 1.2207e–5-dB gain change per sample period. Attack rates should be programmed such that before the output of the DAC digital volume control can clip, the input signal should be sufficiently attenuated. High attack rates can cause audible artifacts, and tooslow attack rates may not be able to prevent the input signal from clipping. The recommended DRC attack rate value is 1.9531e–4 dB per sample period. 5.6.4.5 DRC Decay Rate When the DRC detects a reduction in output signal swing beyond the programmed DRC threshold, the DRC enters a decay state, where the applied gain in the digital-volume control is gradually increased to programmed values. To avoid audible artifacts, the gain is slowly increased with a rate equal to the decay rate programmed through page 0 / register 70, bits D3–D0. The decay rates can be programmed from 1.5625e–3 dB per sample period to 4.7683e–7 dB per sample period. If the decay rates are programmed too high, then sudden gain changes can cause audible artifacts. However, if it is programmed too slow, then the output may be perceived as too low for a long time after the peak signal has passed. The recommended Value of DRC attack rate is 2.4414e–5 dB per sample period. 5.6.4.6 • • • • • • Example Setup for DRC DAC vol gain = 12 dB Threshold = –24 dB Hysteresis = 3 dB Hold time = 0 ms Attack rate = 1.9531e–4 dB per sample period Decay rate = 2.4414e–5 dB per sample period Script #Go to Page 0 w 30 00 00 #DAC => 12 db gain mono w 30 41 18 #DAC => DRC Enabled, Threshold = 24 db, Hysteresis = 3 dB w 30 44 7F #DRC Hold = 0 ms, Rate of Changes of Gain = 0.5 dB/Fs' w 30 45 00 #Attack Rate = 1.9531e-4 dB/Frame , DRC Decay Rate =2.4414e5 dB/Frame w 30 46 B6 #Go to Page 9 w 30 00 09 #DRC HPF w 30 0E 7F AB 80 55 7F 56 #DRC LPF W 30 14 00 11 00 11 7F DE 5.6.4.7 Headset Detection The TLV320DAC3120 includes extensive capability to monitor a headphone, microphone, or headset jack, to determine if a plug has been inserted into the jack, and then determine what type of headset/headphone is wired to the plug. The device also includes the capability to detect a button press, even, for example, when starting calls on mobile phones with headsets. Figure 5-15 shows the circuit configuration to enable this feature. 34 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 g g s s Hpout HPOUT Micpga m m VOL/MICDET Micbias MICBIAS S0403-01 Figure 5-15. Jack Connections for Headset Detection This feature is enabled by programming page 0 / register 67, bit D1. In order to avoid false detections due to mechanical vibrations in headset jacks or microphone buttons, a debounce function is provided for glitch rejection. For the case of headset insertion, a debounce function with a range of 32 ms to 512 ms is provided. This can be programmed via page 0 / register 67, bits D4–D2. For improved button-press detection, the debounce function has a range of 8 ms to 32 ms by programming page 0 / register 67, bits D1–D0. The TLV320DAC3120 also provides feedback to the user when a button press or a headset insertion/removal event is detected through register-readable flags or an interrupt on the I/O pins. The value in page 0 / register 46, bits D5–D4 provides the instantaneous state of button press and headset insertion. Page 0 / register 44, bit D5 is a sticky (latched) flag that is set when the button-press event is detected. Page 0 / register 44, bit D4 is a sticky flag which is set when the headset insertion or removal event is detected. These sticky flags are set by the event occurrence, and are reset only when read. This requires polling page 0 / register 44. To avoid polling and the associated overhead, the TLV320DAC3120 also provides an interrupt feature whereby the events can trigger the INT1 and/or INT2 interrupts. These interrupt events can be routed to one of the digital output pins. See Section 5.6.4.8 for details. The TLV320DAC3120 not only detects a headset-insertion event, but also is able to distinguish between the different headsets inserted, such as stereo headphones or cellular headphones. After the headsetdetection event, the user can read page 0 / register 67, bits D6–D5 to determine the type of headset inserted. Table 5-16. Headset-Detection Block Registers Register Description Page 0 / register 67, bit D1 Headset-detection enable/disable Page 0 / register 67, bits D4–D2 Debounce programmability for headset detection Page 0 / register 67, bits D1–D0 Debounce programmability for button press Page 0 / register 44, bit D5 Sticky flag for button-press event Page 0 / register 44, bit D4 Sticky flag for headset-insertion or -removal event Page 0/ register 46, bit D5 Status flag for button-press event Page 0 / register 46, bit D4 Status flag for headset insertion and removal Page 0 / register 67, bits D6–D5 Flags for type of headset detected APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 35 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com The headset detection block requires AVDD to be powered. The headset-detection feature in the TLV320DAC3120 is achieved with very low power overhead, requiring less than 20 μA of additional current from the AVDD supply. 5.6.4.8 Interrupts Some specific events in the TLV320DAC3120, which may require host-processor intervention, can be used to trigger interrupts to the host processor. This avoids polling the status-flag registers continuously. The TLV320DAC3120 has two defined interrupts, INT1 and INT2, that can be configured by programming page 0 / register 48 and page 0 / register 49. A user can configure interrupts INT1 and INT2 to be triggered by one or many events, such as: • Headset detection • Button press • DAC DRC signal exceeding threshold • Noise detected by AGC • Overcurrent condition in headphone drivers/speaker drivers • Data overflow in the DAC processing blocks and filters • DC measurement data available Each of these INT1 and INT2 interrupts can be routed to output pin GPIO1. These interrupt signals can either be configured as a single pulse or a series of pulses by programming page 0 / register 48, bit D0 and page 0 / register 49, bit D0. If the user configures the interrupts as a series of pulses, the events trigger the start of pulses that stop when the flag registers in page 0 / register 44, page 0 / register 45, and page 0 / register 50 are read by the user to determine the cause of the interrupt. 5.6.5 Key-Click Functionality With Beep Generator (PRB_P25) A special algorithm has been included in the digital signal processing block PRB_P25 for generating a digital sine-wave signal that is sent to the DAC. This functionality is intended for generating key-click sounds for user feedback. The sine-wave generator is very flexible (see Table 5-17) and is completely register programmable. Programming page 0 / register 71 through page 0 / register 79 (8 bits each) completely controls the functionality of this generator and allows for differentiating sounds. The two registers used for programming the 16-bit sine-wave coefficient are page 0 / register 76 and page 0 / register 77. The two registers used for programming the 16-bit cosine-wave coefficient are page 0 / register 78 and page 0 / register 79. This coefficient resolution allows virtually any frequency of sine wave in the audio band to be generated, up to fS/2. The three registers used to control the length of the sine-burst waveform are page 0 / register 73 through page 0 / register 75. The resolution (bit) in the registers of the sine-burst length is one sample time, so this allows great control on the overall time of the sine-burst waveform. This 24-bit length timer supports 16,777,215 sample times. (For example, if fS is set at 48 kHz, and the register value equals 96,000d (01 7700h), then the sine burst lasts exactly 2 seconds.) The default settings for the tone generator, based on using a sample rate of 48 kHz, are 1-kHz (approximately) sine wave, with a sine-burst length of five cycles (5 ms). Table 5-17. Beep Generator Register Locations (Page 00h) REGISTER 36 LEFT BEEP CONTROL RIGHT BEEP CONTROL 71 72 BEEP LENGTH SINE COSINE MSB MID LSB MSB LSB MSB LSB 73 74 75 76 77 78 79 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 5-18. Example Beep-Generator Settings for a 1000-Hz Tone BEEP FREQUENCY (1) BEEP LENGTH SINE COSINE SAMPLE RATE Hz MSB (hex) MID (hex) LSB (hex) MSB (hex) LSB (hex) MSB (hex) LSB (hex) Hz 1000 (1) 0 0 EE 10 D8 7E E3 48,000 These are the default settings. Two registers are used to control the left sine-wave volume and the right sine-wave volume independently. The 6-bit digital volume control used allows level control of 2 dB to –61 dB in 1-dB steps. The left-channel volume is controlled by writing to page 0 / register 71, bits D5–D0. The right-channel volume is controlled by writing to page 0, register 72, bits D5–D0. A master volume control that controls the left and right channels of the beep generator can be set up by writing to page 0 / register 72, bits D7–D6. The default volume control setting is 2 dB, which provides the maximum tone-generator output level. For generating other tones, the three tone-generator coefficients can be found by running the following script using MATLAB™ : Sine = dec2hex(round(sin(2*pi*Fin/Fs)*2^15)) Cosine = dec2hex(round(cos(2*pi*Fin/Fs)*2^15)) Beep Length = dec2hex(floor(Fs*Cycle/Fin)) where, fin = Beep frequency desired fS = Sample rate Cycle = Number of beep (sine wave) cycles that are needed dec2hex = Decimal to hexadecimal conversion function NOTES: 1. fin should be less than fS/4. 2. For the sine and cosine values, if the number of bits is less than the full 16-bit value, then the unused MSBs must be written as 0s. 3. For the beep-length values, if number of bits is less than the full 24-bit value, then the unused MSBs must be written as 0s. Following the beep-volume control is a digital mixer that mixes in a playback data stream whose level has already been set by the DAC volume control. Therefore, once the key-click volume level is set, the keyclick volume is not affected by the DAC volume control, which is the main control available to the end user. This functionality is shown in Figure 1-1. Following the DAC, the signal can be further scaled by the analog output volume control and poweramplifier level control. The beep generator is used for the key-click function. A single beep is generated by writing to page 0 / register 71, bit D7. After the programmed beep length has finished, register 71, bit D7 is reset back to zero. 5.6.6 Programming DAC Digital Filter Coefficients The digital filter coefficients must be programmed through the I2C interface. All digital filtering for the DAC signal path must be loaded into the RAM before the DAC is powered on. (Note that default ALLPASS filter coefficients for programmable biquads are located in boot ROM. The boot ROM automatically loads the default values into the RAM following a hardware reset (toggling the RESET pin) or after a software reset. After resetting the device, loading boot ROM coefficients into the digital filters requires 100 μs of programming time. During this time, reading or writing to page 8 through page 15 for updating DAC filter coefficient values is not permitted. (The DAC should not be powered up until after all of the DAC configurations have been done by the system microprocessor.) APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 37 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.6.7 www.ti.com Updating DAC Digital Filter Coefficients During PLAY When it is required to update the DAC digital filter coefficients during play, care must be taken to avoid click and pop noise or even a possible oscillation noise. These artifacts can occur if the DAC coefficients are updated without following the proper update sequence. The correct sequence is shown in Figure 5-16. The values for times listed in Figure 5-16 are conservative and should be used for software purposes. There is also an adaptive mode, in which DAC coefficients can be updated while the DAC is on. For details, see Section 5.6.1.3. Play - Paused Volume Ramp Down Soft Mute Wait (A) ms DAC Volume Ramp Down WAIT Time (A) For fS = 32 kHz ® Wait 25 ms (min) DAC Power Down Update Digital Filter Coefficients For fS = 48 kHz ® Wait 20 ms (min) DAC Volume Ramp Up Time (B) For fS = 32 kHz ® 25 ms DAC Power UP For fS = 48 kHz ® 20 ms Wait 20 ms Restore Previous Volume Level (Ramp) in (B) ms Play - Continue F0024-02 Figure 5-16. Example Flow For Updating DAC Digital Filter Coefficients During Play 38 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com 5.6.8 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Digital Mixing and Routing The TLV320DAC3120 has four digital mixing blocks. Each mixer can provide either mixing or multiplexing of the digital audio data. The first mixer/multiplexer can be used to select input data for the mono DAC from left channel, right channel, or a mix of the left and right channels [(L + R) / 2]. This digital routing can be configured by writing to page 0 / register 63, bits D5–D4 for the DAC mono channel. 5.6.9 Analog Audio Routing The TLV320DAC3120 has the capability to route the DAC output to either the headphone or the speaker output. If desirable, both output drivers can be operated at the same time while playing at different volume levels. The TLV320DAC3120 provides various digital routing capabilities, allowing digital mixing or even channel swapping in the digital domain. All analog outputs other than the selected ones can be powered down for optimal power consumption. 5.6.9.1 Analog Output Volume Control The output volume control can be used to fine-tune the level of the mixer amplifier signal supplied to the headphone driver or the speaker driver. This architecture supports separate and concurrent volume levels for each of the four output drivers. This volume control can also be used as part of the output pop-noise reduction scheme. This feature is available even if the DAC is powered down. 5.6.9.2 Headphone Analog Output Volume Control For the headphone outputs, the analog volume control has a range from 0 dB to –78 dB in 0.5-dB steps for most of the useful range plus mute, as shown in Table 5-19. This volume control includes soft-stepping logic. Routing the DAC output signal to the analog volume control is done by writing to page 1 / register 35, bits D7–D6. Changing the analog volume for the headphone is controlled by writing to page 1 / register 36, bits D6–D0. Routing the signal from the output of the analog volume control to the input of the headphone power amplifier is done by writing to page 1 / register 36, bit D7. The analog volume-control soft-stepping time is based on the setting in page 0 / register 63, bits D1–D0. APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 39 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 5-19. Analog Volume Control for Headphone and Speaker Outputs (for D7 = 1) (1) Register Value (D6–D0) (1) Analog Gain (dB) Register Value (D6–D0) Analog Gain (dB) Register Value (D6–D0) Analog Gain (dB) Register Value (D6–D0) Analog Gain (dB) 0 0.0 30 –15.0 60 –30.1 90 –45.2 1 –0.5 31 –15.5 61 –30.6 91 –45.8 2 –1.0 32 –16.0 62 –31.1 92 –46.2 3 –1.5 33 –16.5 63 –31.6 93 –46.7 4 –2.0 34 –17.0 64 –32.1 94 –47.4 5 –2.5 35 –17.5 65 –32.6 95 –47.9 6 –3.0 36 –18.1 66 –33.1 96 –48.2 7 –3.5 37 –18.6 67 –33.6 97 –48.7 8 –4.0 38 –19.1 68 –34.1 98 –49.3 9 –4.5 39 –19.6 69 –34.6 99 –50.0 10 –5.0 40 –20.1 70 –35.2 100 –50.3 11 –5.5 41 –20.6 71 –35.7 101 –51.0 12 –6.0 42 –21.1 72 –36.2 102 –51.4 13 –6.5 43 –21.6 73 –36.7 103 –51.8 14 –7.0 44 –22.1 74 –37.2 104 –52.2 15 –7.5 45 –22.6 75 –37.7 105 –52.7 16 –8.0 46 –23.1 76 –38.2 106 –53.7 17 –8.5 47 –23.6 77 –38.7 107 –54.2 18 –9.0 48 –24.1 78 –39.2 108 –55.3 19 –9.5 49 –24.6 79 –39.7 109 –56.7 20 –10.0 50 –25.1 80 –40.2 110 –58.3 21 –10.5 51 –25.6 81 –40.7 111 –60.2 22 –11.0 52 –26.1 82 –41.2 112 –62.7 23 –11.5 53 –26.6 83 –41.7 113 –64.3 24 –12.0 54 –27.1 84 –42.1 114 –66.2 25 –12.5 55 –27.6 85 –42.7 115 –68.7 26 –13.0 56 –28.1 86 –43.2 116 –72.2 27 –13.5 57 –28.6 87 –43.8 117–127 –78.3 28 –14.0 58 –29.1 88 –44.3 29 –14.5 59 –29.6 89 –44.8 Mute when D7 = 0 and D6–D0 = 127 (0x7F). 5.6.9.3 Class-D Speaker Analog Output Volume Control For the speaker outputs, the analog volume control has a range from 0 dB to –78 dB in 0.5-dB steps for most of the useful range plus mute, as seen in Table 5-19. The implementation includes soft-stepping logic. Routing the DAC output signal to the analog volume control is done by writing to page 1 / register 35, bits D7–D6. Changing the analog volume for the speaker is controlled by writing to page 1 / register 38, bits D6–D0. Routing the signal from the output of the analog volume control to the input of the speaker amplifier is done by writing to page 1 / register 38, bit D7. The analog volume-control soft-stepping time is based on the setting in page 0 / register 63, bits D1–D0. 5.6.10 Analog Outputs Various analog routings are supported for playback. All the options can be conveniently viewed on the functional block diagram, Figure 1-1. 40 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.6.10.1 Headphone Drivers The TLV320DAC3120 features a mono headphone driver (HPOUT) that can deliver up to 30 mW per channel, at 3.3-V supply voltage, into a 16-Ω load. The headphones are used in a single-ended configuration where an ac-coupling (dc-blocking) capacitor is connected between the device output pins and the headphones. The headphone driver also supports 32-Ω and 10-kΩ loads without changing any control register settings. The headphone drivers can be configured to optimize the power consumption in the lineout-drive mode by writing 11 to page 1 / register 44, bits D2–D1. The output common mode of the headphone/lineout drivers can be programmed to 1.35 V, 1.5 V, 1.65 V, or 1.8 V by setting page 1 / register 31, bits D4–D3. The common-mode voltage should be set ≤ AVDD/2. The headphone driver can be powered on by writing to page 1 / register 31, bit D7. The HPOUT output driver gain can be controlled by writing to page 1 / register 40, bits D6–D3, and it can be muted by writing to page 1 / register 40, bit D2. The TLV320DAC3120 has a short-circuit protection feature for the headphone drivers, which is always enabled to provide protection. The output condition of the headphone driver during short circuit can be programmed by writing to page 1 / register 31, bit D1. If D1 = 0 when a short circuit is detected, the device limits the maximum current to the load. If D1 = 1 when a short circuit is detected, the device powers down the output driver. The default condition for headphones is the current-limiting mode. In case of a short circuit on either channel, the output is disabled and a status flag is provided as read-only bits on page 1 / register 31, bit D0. If shutdown mode is enabled, then as soon as the short circuit is detected, page 1 / register 31, bit D7 (for HPLOUT) clears automatically. Next, the device requires a reset to re-enable the output stage. Resetting can be done in two ways. First, the device master reset can be used, which requires either toggling the RESET pin or using the software reset. If master reset is used, it resets all of the registers. Second, a dedicated headphone power-stage reset can also be used to re-enable the output stage, and that keeps all of the other device settings. The headphone power stage reset is done by setting page 1 / register 31, bit D7 for HPLOUT. If the fault condition has been removed, then the device returns to normal operation. If the fault is still present, then another shutdown occurs. Repeated resetting (more than three times) is not recommended, as this could lead to overheating. 5.6.10.2 Speaker Drivers The TLV320DAC3120 has an integrated class-D mono speaker driver (SPKP/SPKM) capable of driving an 8-Ω or 4-Ω differential load. The speaker driver can be powered directly from the battery supply (2.7 V to 5.5 V) on the SPKVDD pins; however, the voltage (including spike voltage) must be limited below the absolute-maximum voltage of 6 V. The speaker driver is capable of supplying 400 mW per channel with a 3.6-V power supply. Through the use of digital mixing, the device can connect one or both digital audio playback data channels to either speaker driver; this also allows digital channel swapping if needed. The class-D speaker driver can be powered on by writing to page 1 / register 32, bit D7. The class-D output-driver gain can be controlled by writing to page 1 / register 42, bits D4–D3, and it can be muted by writing to page 1 / register 42, bit D2. The TLV320DAC3120 has a short-circuit protection feature for the speaker drivers that is always enabled to provide protection. If the output is shorted, the output stage shuts down on the overcurrent condition. (Current limiting is not an available option for the higher-current speaker driver output stage.) In case of a short circuit, the output is disabled and a status flag is provided as a read-only bit on page 1 / register 32, bit D0. APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 41 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com If shutdown occurs due to an overcurrent condition, then the device requires a reset to re-enable the output stage. Resetting can be done in two ways. First, the device master reset can be used, which requires either toggling the RESET pin or using the software reset. If master reset is used, it resets all of the registers. Second, a dedicated speaker power-stage reset can be used that keeps all of the other device settings. The speaker power-stage reset is done by setting page 1 / register 32, bit D7 for SPKP and SPKM. If the fault condition has been removed, then the device returns to normal operation. If the fault is still present, then another shutdown occurs. Repeated resetting (more than three times) is not recommended, as this could lead to overheating. To minimize battery current leakage, the SPKVDD voltage level should not be less than the AVDD voltage level. The TLV320DAC3120 has a thermal protection (OTP) feature for the speaker drivers which is always enabled to provide protection. If the device is overheated, then the output stops switching. When the device cools down, the output resumes switching. An overtemperature status flag is provided as a readonly bit on page 0 / register 3, bit D1. The OTP feature is for self-protection of the device. If die temperature can be controlled at the system/board level, then overtemperature does not occur. 5.6.11 Audio Output-Stage Power Configurations After the device has been configured (following a RESET) and the circuitry has been powered up, the audio output stage can be powered up and powered down by register control. These functions soft-start automatically. By using these register controls, it is possible to turn all four stages on at the same time without turning two of them off. See Table 5-20 for register control of audio output stage power configurations. Table 5-20. Audio Output Stage Power Configurations 5.7 Audio Output Pins Desired Function Page 1 / Register, Bit Value HPOUT Power-down HPOUT driver Page 1 / register 31, bit D7 = 0 HPOUT Power-up HPOUT driver Page 1 / register 31, bit D7 = 1 SPKP / SPKM Power-down class-D driver Page 1 / register 32, bit D7 = 0 SPKP / SPKM Power-up class-D driver Page 1 / register 32, bit D7 = 1 CLOCK Generation and PLL The TLV320DAC3120 supports a wide range of options for generating clocks for the DAC sections as well as interface and other control blocks as shown in Figure 5-17. The clocks for the DAC require a source reference clock. This clock can be provided on a variety of device pins, such as the MCLK, BCLK, or GPIO1 pins. The source reference clock for the codec can be chosen by programming the CODEC_CLKIN value on page 0 / register 4, bits D1–D0. The CODEC_CLKIN can then be routed through highly-flexible clock dividers shown in Figure 5-17 to generate the various clocks required for the DAC and the miniDSP section. In the event that the desired audio clocks cannot be generated from the reference clocks on MCLK, BCLK, or GPIO1, the TLV320DAC3120 also provides the option of using the on-chip PLL which supports a wide range of fractional multiplication values to generate the required clocks. Starting from CODEC_CLKIN, the TLV320DAC3120 provides several programmable clock dividers to help achieve a variety of sampling rates for the DAC and clocks for the miniDSP sections. 42 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 BCLK MCLK DIN GPIO1 PLL_CLKIN PLL ´ (R ´ J.D)/P BCLK MCLK GPIO1 PLL_CLK CODEC_CLKIN ¸ NDAC To DAC miniDSP Clock Generation NDAC = 1, 2, ..., 127, 128 DAC_CLK ¸ MDAC MDAC = 1, 2, ..., 127, 128 DAC_MOD_CLK ¸ DOSR DOSR = 1, 2, ..., 1023, 1024 DAC_fS B0357-06 Figure 5-17. Clock Distribution Tree DAC _ MOD _ CLK = DAC _ fS = CODEC _ CLKIN NDAC ´ MDAC CODEC _ CLKIN NDAC ´ MDAC ´ DOSR (5) Table 5-21. CODEC CLKIN Clock Dividers Divider Bits NDAC Page 0 / register 11, bits D6–D0 MDAC Page 0 / register 12, bits D6–D0 DOSR Page 0 / register 13, bits D1–D0 and page 0 / register 14, bits D7–D0 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 43 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com The DAC modulator is clocked by DAC_MOD_CLK. For proper power-up operation of the DAC channel, these clocks must be enabled by configuring the NDAC and MDAC clock dividers (page 0 / register 11, bit D7 = 1 and page 0 / register 12, bit D7 = 1). When the DAC channel is powered down, the device internally initiates a power-down sequence for proper shut-down. During this shutdown sequence, the NDAC and MDAC dividers must not be powered down, or else a proper low-power shutdown may not take place. The user can read back the power-status flag at page 0 / register 37, bit D7 and page 0 / register 37, bit D3. When both the flags indicate power-down, the MDAC divider may be powered down, followed by the NDAC divider. In general, all the root clock dividers should be powered down only after the child clock dividers have been powered down for proper operation. The TLV320DAC3120 also has options for routing some of the internal clocks to the GPIO1 output pin to be used as general-purpose clocks in the system. The feature is shown in Figure 5-19. DAC_CLK DAC_MOD_CLK BDIV_CLKIN ÷N N = 1, 2, ..., 127, 128 BCLK B0362-01 Figure 5-18. BCLK Output Options In the mode when TLV320DAC3120 is configured to drive the BCLK pin (page 0 / register 27, bit D3 = 1), it can be driven as a divided value of BDIV_CLKIN. The division value can be programmed in page 0 / register 30, bits D6–D0 from 1 to 128 (see Figure 5-18). The BDIV_CLKIN can itself be configured to be one of DAC_CLK (DAC DSP clock) or DAC_MOD_CLK by configuring the BDIV_CLKIN multiplexer in page 0 / register 29, bits D1-D0. Additionally, a general-purpose clock can be driven out on GPIO1. This clock can be a divided-down version of CDIV_CLKIN. The value of this clock divider can be programmed from 1 to 128 by writing to page 0 / register 26, bits D6–D0. The CDIV_CLKIN can itself be programmed as one of the clocks among the list shown in Figure 5-19. This can be controlled by programming the multiplexer in page 0 / register 25, bits D2–D0. 44 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 PLL_CLK MCLK BCLK DIN DAC_MOD_CLK DAC_CLK CDIV_CLKIN M = 1, 2, ..., 127, 128 ÷M GPIO1 (CLKOUT) B0363-01 Figure 5-19. General-Purpose Clock Output Options Table 5-22. Maximum TLV320DAC3120 Clock Frequencies DVDD ≥ 1.65 V Clock 5.7.1 CODEC_CLKIN ≤ 110 MHz DAC_CLK (DAC DSP clock) ≤ 49.152 MHz DAC_miniDSP_CLK ≤ 49.152MHz with DRC disabled ≤ 48 MHz with DRC enabled DAC_MOD_CLK 6.758 MHz DAC_fS 0.192 MHz BDIV_CLKIN 55 MHz CDIV_CLKIN 100 MHz when M is odd 110 MHz when M is even PLL For lower power consumption, it is best to derive the internal audio processing clocks using the simple dividers. When the input MCLK or other source clock is not an integer multiple of the audio processing clocks, then it is necessary to use the on-board PLL. The TLV320DAC3120 fractional PLL can be used to generate an internal master clock used to produce the processing clocks needed by the DAC and miniDSP. The programmability of this PLL allows operation from a wide variety of clocks that may be available in the system. The PLL input supports clocks varying from 512 kHz to 20 MHz and is register programmable to enable generation of required sampling rates with fine resolution. The PLL can be turned on by writing to page 0 / register 5, bit D7. When the PLL is enabled, the PLL output clock PLL_CLK is given by the following equation: PLL_CLKIN ´ R ´ J.D PLL_CLK = P (6) where R = 1, 2, 3, ..., 16 (page 0 / register 5, default value = 1) J = 1, 2, 3, …, 63, (page 0 / register 6, default value = 4) D = 0, 1, 2, …, 9999 (page 0 / register 7 and 8, default value = 0) P = 1, 2, 3, …, 8 (page 0 / register 5, default value = 1) APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 45 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com The PLL can be turned on via page 0 / register 5, bit D7. The variable P can be programmed via page 0 / register 5, bits D6–D4. The variable R can be programmed via page 0 / register 5, bits D3–D0. The variable J can be programmed via page 0 / register 6, bits D5–D0. The variable D is 14 bits and is programmed into two registers. The MSB portion can be programmed via page 0 / register 7, bits D5–D0, and the LSB portion is programmed via page 0 / register 8, bits D7–D0. For proper update of the D-divider value, page 0 / register 7 must be programmed first, followed immediately by page 0 / register 8. Unless the write to page 0 / register 8 is completed, the new value of D does not take effect. When the PLL is enabled, the following conditions must be satisfied. • When the PLL is enabled and D = 0, the following conditions must be satisfied for PLL_CLKIN: PLL _ CLKIN 512 kHz £ £ 20 MHz P • (7) 80 MHz ≤ (PLL_CLKIN × J.D × R/P) ≤ 110 MHz (8) 4 ≤ R × J ≤ 259 (9) When the PLL is enabled and D ≠ 0, the following conditions must be satisfied for PLL_CLKIN: PLL _ CLKIN 10 MHz £ £ 20 MHz P (10) 80 MHz ≤ (PLL_CLKIN × J.D × R/P) ≤ 110 MHz (11) R=1 (12) The PLL can be powered up independently from the DAC blocks, and can also be used as a generalpurpose PLL by routing its output to the GPIO output. After powering up the PLL, PLL_CLK is available typically after 10 ms. The clocks for codec and various signal processing blocks, CODEC_CLKIN can be generated from MCLK input, BCLK input, GPIO input or PLL_CLK (page 0 / register 4, bit D1-D0). If the CODEC_CLKIN is derived from the PLL, then the PLL must be powered up first and powered down last. Table 5-23 lists several example cases of typical PLL_CLKIN rates and how to program the PLL to achieve a sample rate fS of either 44.1 kHz or 48 kHz. 46 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 5-23. PLL Example Configurations PLL_CLKIN (MHz) PLLP PLLR PLLJ PLLD MDAC NDAC DOSR 2.8224 1 3 10 0 3 5 128 5.6448 1 3 5 0 3 5 128 12 1 1 7 560 3 5 128 13 1 1 6 3504 6 3 104 16 1 1 5 2920 3 5 128 19.2 1 1 4 4100 3 5 128 48 4 1 7 560 3 5 128 2.048 1 3 14 0 7 2 128 3.072 1 4 7 0 7 2 128 4.096 1 3 7 0 7 2 128 6.144 1 2 7 0 7 2 128 8.192 1 4 3 0 4 4 128 12 1 1 7 1680 7 2 128 16 1 1 5 3760 7 2 128 19.2 1 1 4 4800 7 2 128 48 4 1 7 1680 7 2 128 fS = 44.1 kHz fS = 48 kHz 5.7.2 Timer The internal clock runs nominally at 8.2 MHz. This is used for various internal timing intervals, de-bounce logics and interrupts. The MCLK divider must be set such a way that the divider output is ~1 MHz for the timers to be closer to the programmed value. Powered on if internal oscillator is selected Internal Oscillator ÷8 0 Interval timers MCLK Programmable Divider Used for de-bounce time for headset detection logic, various power up timers and for generation of interrupts 1 P3/R16, Bits D6-D0 P3/R16, Bit D7 Figure 5-20. Interval Timer Clock Selection APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 47 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.8 www.ti.com Digital Audio and Control Interface 5.8.1 Digital Audio Interface Audio data is transferred between the host processor and the TLV320DAC3120 via the digital audio data serial interface, or audio bus. The audio bus on this device is very flexible, including left- or right-justified data options, support for I2S or PCM protocols, programmable data-length options, a TDM mode for multichannel operation, very flexible master/slave configurability for each bus clock line, and the ability to communicate with multiple devices within a system directly. NOTE The TLV320AIC3102 has a mono DAC, which inputs the mono data from the digital audio data serial interface as the left channel, the right channel, or a mix of the left and right channels as (L + R) ÷ 2 (page 0 / register 63, bits D5–D4). See Figure 1-1 for the signal flow of the DAC blocks. The audio bus of the TLV320DAC3120 can be configured for left- or right-justified, I2S, DSP, or TDM modes of operation, where communication with standard telephony PCM interfaces is supported within the TDM mode. These modes are all MSB-first, with data width programmable as 16, 20, 24, or 32 bits by configuring page 0 / register 27, bits D5–D4. In addition, the word clock and bit clock can be independently configured in either master or slave mode for flexible connectivity to a wide variety of processors. The word clock is used to define the beginning of a frame, and may be programmed as either a pulse or a square-wave signal. The frequency of this clock corresponds to the maximum of the selected DAC sampling frequencies. The bit clock is used to clock in and clock out the digital audio data across the serial bus. When in master mode, this signal can be programmed to generate variable clock pulses by controlling the bit-clock divider in page 0 / register 30 (see Figure 5-17). The number of bit-clock pulses in a frame may need adjustment to accommodate various word lengths as well as to support the case when multiple TLV320DAC3120s may share the same audio bus. The TLV320DAC3120 also includes a feature to offset the position of start of data transfer with respect to the word clock. This offset can be controlled in terms of number of bit clocks and can be programmed in page 0 / register 28. The TLV320DAC3120 also has the feature of inverting the polarity of the bit clock used for transferring the audio data as compared to the default clock polarity used. This feature can be used independently of the mode of audio interface chosen. This can be configured via page 0 / register 29, bit D3. By default, when the word clocks and bit clocks are generated by the TLV320DAC3120, these clocks are active only when the DAC is powered up within the device. This is done to save power. However, it also supports a feature when both the word clocks and bit clocks can be active even when the codec in the device is powered down. This is useful when using the TDM mode with multiple codecs on the same bus, or when word clocks or bit clocks are used in the system as general-purpose clocks. 5.8.1.1 Right-Justified Mode The audio interface of the TLV320DAC3120 can be put into right-justified mode by programming page 0 / register 27, bits D7–D6 = 10. In right-justified mode, the LSB of the left channel is valid on the rising edge of the bit clock preceding the falling edge of the word clock. Similarly, the LSB of the right channel is valid on the rising edge of the bit clock preceding the rising edge of the word clock. 48 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 1/fS WCLK BCLK Right Channel Left Channel DIN 0 n–1 n–2 n–3 MSB 2 1 0 n–1 n–2 n–3 2 1 0 LSB T0149-05 Figure 5-21. Timing Diagram for Right-Justified Mode For right-justified mode, the number of bit clocks per frame should be greater than or equal to twice the programmed word length of the data. APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 49 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 5.8.1.2 www.ti.com Left-Justified Mode The audio interface of the TLV320DAC3120 can be put into left-justified mode by programming page 0 / register 27, bits D7–D6 = 11. In left-justified mode, the MSB of the right channel is valid on the rising edge of the bit clock following the falling edge of the word clock. Similarly, the MSB of the left channel is valid on the rising edge of the bit clock following the rising edge of the word clock. WORD CLOCK LEFT CHANNEL RIGHT CHANNEL BIT CLOCK DATA N N N - - 1 2 3 3 2 1 N N N - - 1 2 3 0 3 LD(n) 2 1 N N N - - 1 2 3 0 RD(n) LD(n) = n'th sample of left channel data LD(n+1) RD(n) = n'th sample of right channel data Figure 5-22. Timing Diagram for Left-Justified Mode WORD CLOCK LEFT CHANNEL RIGHT CHANNEL BIT CLOCK DATA N N N - - 1 2 3 3 2 1 0 N N N - - 1 2 3 LD(n) 3 2 1 0 RD(n) LD(n) = n'th sample of left channel data N N N - - 1 2 3 LD(n+1) RD(n) = n'th sample of right channel data Figure 5-23. Timing Diagram for Left-Justified Mode With Offset = 1 WORD CLOCK LEFT CHANNEL RIGHT CHANNEL BIT CLOCK N N N - - 1 2 3 DATA 3 2 1 N N N - - 1 2 3 0 LD(n) 3 2 1 0 RD(n) LD(n) = n'th sample of left channel data N N N - - 1 2 3 3 LD(n+1) RD(n) = n'th sample of right channel data Figure 5-24. Timing Diagram for Left-Justified Mode With Offset = 0 and Inverted Bit Clock For left-justified mode, the number of bit clocks per frame should be greater than or equal to twice the programmed word length of the data. Also, the programmed offset value should be less than the number of bit clocks per frame by at least the programmed word length of the data. 5.8.1.3 I2S Mode The audio interface of the TLV320DAC3120 can be put into I2S mode by programming page 0 / register 27, bits D7–D6 = to 00. In I2S mode, the MSB of the left channel is valid on the second rising edge of the bit clock after the falling edge of the word clock. Similarly, the MSB of the right channel is valid on the second rising edge of the bit clock after the rising edge of the word clock. 50 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 WORD CLOCK LEFT CHANNEL RIGHT CHANNEL BIT CLOCK N N N - - 1 2 3 DATA 3 2 1 N N N - - 1 2 3 0 LD(n) 3 2 1 N N N - - 1 2 3 0 RD(n) LD(n) = n'th sample of left channel data 3 LD(n+1) RD(n) = n'th sample of right channel data Figure 5-25. Timing Diagram for I2S Mode WORD CLOCK LEFT CHANNEL RIGHT CHANNEL BIT CLOCK N 1 DATA 5 4 3 2 1 N 1 0 5 4 LD(n) 3 2 1 N 1 0 RD(n) LD(n) = n'th sample of left channel data 5 LD (n+1) RD(n) = n'th sample of right channel data 2 Figure 5-26. Timing Diagram for I S Mode With Offset = 2 WORD CLOCK LEFT CHANNEL RIGHT CHANNEL BIT CLOCK DATA N N N - - 1 2 3 3 2 1 N N N - - 1 2 3 0 LD(n) 3 2 1 N N N - - 1 2 3 0 RD(n) LD(n) = n'th sample of left channel data 3 LD(n+1) RD(n) = n'th sample of right channel data 2 Figure 5-27. Timing Diagram for I S Mode With Offset = 0 and Bit Clock Inverted For I2S mode, the number of bit clocks per channel should be greater than or equal to the programmed word length of the data. Also the programmed offset value should be less than the number of bit clocks per frame by at least the programmed word length of the data. 5.8.1.4 DSP Mode The audio interface of the TLV320DAC3120 can be put into DSP mode by programming page 0 / register 27, bits D7–D6 = 01. In DSP mode, the falling edge of the word clock starts the data transfer with the left-channel data first and immediately followed by the right-channel data. Each data bit is valid on the falling edge of the bit clock. APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 51 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 WORD CLOCK www.ti.com LEFT CHANNEL RIGHT CHANNEL BIT CLOCK DATA N N N - - 1 2 3 3 2 1 0 N N N - - 1 2 3 LD(n) 3 2 1 N N N - - 1 2 3 0 RD(n) LD(n) = n'th sample of left channel data 3 LD (n+1) RD(n) = n'th sample of right channel data Figure 5-28. Timing Diagram for DSP Mode WORD CLOCK LEFT CHANNEL RIGHT CHANNEL BIT CLOCK DATA N N N - - 1 2 3 3 2 1 0 N N N - - 1 2 3 LD(n) 3 2 1 N N N - - 1 2 3 0 RD(n) LD(n) = n'th sample of left channel data LD(n+1) RD(n) = n'th sample of right channel data Figure 5-29. Timing Diagram for DSP Mode With Offset = 1 WORD CLOCK LEFT CHANNEL RIGHT CHANNEL BIT CLOCK DATA N N N - - 1 2 3 3 LD(n) 2 1 0 N N N - - 1 2 3 3 2 1 0 N N N - - 1 2 3 RD(n) 3 LD(n+1) Figure 5-30. Timing Diagram for DSP Mode With Offset = 0 and Bit Clock Inverted For DSP mode, the number of bit clocks per frame should be greater than or equal to twice the programmed word length of the data. Also, the programmed offset value should be less than the number of bit clocks per frame by at least the programmed word length of the data. 52 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com 5.8.1.5 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Primary and Secondary Digital Audio Interface Selection The audio serial interface on the TLV320DAC3120 has I/O control to allow communication with two independent processors for audio data. The processors can communicate with the device one at a time. This feature is enabled by register programming of the various pin selections. Table 5-24 shows the primary and secondary audio interface selection and registers. Figure 5-31 is a high-level diagram showing the general signal flow and multiplexing for the primary and secondary audio interfaces. For detailed information, see the tables of register definitions (Section 6). Table 5-24. Primary and Secondary Audio Interface Selection Desired Pin Function Possible Pins Primary WCLK (OUT) WCLK Primary WCLK (IN) WCLK Page 0 Registers Comment R27/D2 = 1 Primary WCLK is output from codec R33/D5–D4 Select source of primary WCLK (DAC_fs or secondary WCLK) R27/D2 = 0 Primary WCLK is input to codec R27/D3 = 1 Primary BCLK is output from codec R33/D7 Select source of primary WCLK (internal BCLK or secondary BCLK) Primary BCLK (OUT) BCLK Primary BCLK (IN) BCLK R27/D3 = 0 Primary BCLK is input to codec Primary DIN (IN) DIN R32/D0 Select DIN to internal interface (0 = primary DIN; 1 = secondary DIN) R31/D4–D2 = 000 Secondary WCLK obtained from GPIO1 pin Secondary WCLK (OUT) GPIO1 R51/D5–D2 = 1001 GPIO1 is secondary WCLK output. Secondary WCLK (IN) GPIO1 Secondary BCLK (OUT) GPIO1 Secondary BCLK (IN) Secondary DIN (IN) GPIO1 GPIO1 R33/D3–D2 Select source of Secondary WCLK (DAC_fS or primary WCLK) R31/D4–D2 = 000 Secondary WCLK obtained from GPIO1 pin R51/D5–D2 = 0001 GPIO1 enabled as secondary input R31/D7–D5 = 000 Secondary BCLK obtained from GPIO1 pin R51/D5–D2 = 1000 GPIO1 is secondary BCLK output. R33/D6 Select source of secondary BCLK (primary BCLK or internal BCLK) R31/D7–D5 = 000 Secondary BCLK obtained from GPIO1 pin R51/D5–D2 = 0001 GPIO1 enabled as secondary input R31/D1–D0 = 00 Secondary DIN obtained from GPIO1 pin R51/D5–D2 = 0001 GPIO1 enabled as secondary input APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 53 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com S_BCLK BCLK BCLK BCLK BCLK_OUT BCLK_INT S_BCLK WCLK S_WCLK WCLK WCLK DAC_fS Primary Audio Processor DAC_WCLK_INT S_WCLK Audio Digital Serial Interface DIN DOUT DIN DIN_INT S_DIN DIN BCLK2 GPIO1 S_BCLK BCLK BCLK BCLK_OUT WCLK2 GPIO1 S_WCLK WCLK WCLK BCLK_OUT DAC_fS Secondary Audio Processor GPIO1 DAC_fS Clock Generation S_DIN DOUT DIN B0375-01 Figure 5-31. Audio Serial Interface Multiplexing 5.8.2 Control Interface The TLV320DAC3120 control interface supports the I2C communication protocol. 5.8.2.1 I2C Control Mode The TLV320DAC3120 supports the I2C control protocol, and will respond to the I2C address of 0011 000. I2C is a two-wire, open-drain interface supporting multiple devices and masters on a single bus. Devices on the I2C bus only drive the bus lines LOW by connecting them to ground; they never drive the bus lines HIGH. Instead, the bus wires are pulled HIGH by pullup resistors, so the bus wires are HIGH when no device is driving them LOW. This way, two devices cannot conflict; if two devices drive the bus simultaneously, there is no driver contention. 54 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Communication on the I2C bus always takes place between two devices, one acting as the master and the other acting as the slave. Both masters and slaves can read and write, but slaves can only do so under the direction of the master. Some I2C devices can act as masters or slaves, but the TLV320DAC3120 can only act as a slave device. An I2C bus consists of two lines, SDA and SCL. SDA carries data, and the SCL signal provides the clock. All data is transmitted across the I2C bus in groups of eight bits. To send a bit on the I2C bus, the SDA line is driven to the appropriate level while SCL is LOW (a LOW on SDA indicates the bit is 0, while a HIGH indicates the bit is 1). Once the SDA line has settled, the SCL line is brought HIGH, then LOW. This pulse on the SCL line clocks the SDA bit into the receiver shift register. The I2C bus is bidirectional: the SDA line is used both for transmitting and receiving data. When a master reads from a slave, the slave drives the data line; when a master sends to a slave, the master drives the data line. Most of the time the bus is idle, no communication is taking place, and both lines are HIGH. When communication is taking place, the bus is active. Only master devices can start communication on the bus. Normally, the data line is only allowed to change state while the clock line is LOW. If the data line changes state while the clock line is HIGH, it is either a START condition or its counterpart, a STOP condition. A START condition is when the clock line is HIGH and the data line goes from HIGH to LOW. A STOP condition is when the clock line is HIGH and the data line goes from LOW to HIGH. After the master issues a START condition, it sends a byte that selects the slave device for communication. This byte is called the address byte. Each device on an I2C bus has a unique 7-bit address to which it responds. (Slaves can also have 10-bit addresses; see the I2C specification for details.) The master sends an address in the address byte, together with a bit that indicates whether it wishes to read from or write to the slave device. Every byte transmitted on the I2C bus, whether it is address or data, is acknowledged with an acknowledge bit. When a master has finished sending a byte (8 data bits) to a slave, it stops driving SDA and waits for the slave to acknowledge the byte. The slave acknowledges the byte by pulling SDA LOW. The master then sends a clock pulse to clock the acknowledge bit. Similarly, when a master has finished reading a byte, it pulls SDA LOW to acknowledge this to the slave. It then sends a clock pulse to clock the bit. (Remember that the master always drives the clock line.) A not-acknowledge is performed by simply leaving SDA HIGH during an acknowledge cycle. If a device is not present on the bus, and the master attempts to address it, it will receive a not-acknowledge because no device is present at that address to pull the line LOW. When a master has finished communicating with a slave, it may issue a STOP condition. When a STOP condition is issued, the bus becomes idle again. A master may also issue another START condition. When a START condition is issued while the bus is active, it is called a repeated START condition. The TLV320DAC3120 can also respond to and acknowledge a general call, which consists of the master issuing a command with a slave address byte of 00h. This feature is disabled by default, but can be enabled via page 0 / register 34, bit D5. SCL DA(6) SDA Start (M) DA(0) 7-bit Device Address (M) RA(7) Write (M) Slave Ack (S) RA(0) 8-bit Register Address (M) D(7) Slave Ack (S) D(0) 8-bit Register Data (M) Slave Ack (S) Stop (M) (M) => SDA Controlled by Master (S) => SDA Controlled by Slave Figure 5-32. I2C Write APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 55 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com SCL DA(6) SDA Start (M) DA(0) 7-bit Device Address (M) RA(7) Write (M) Slave Ack (S) DA(6) RA(0) 8-bit Register Address (M) Slave Ack (S) Repeat Start (M) DA(0) 7-bit Device Address (M) D(7) Read (M) Slave Ack (S) 8-bit Register Data (S) D(0) Master No Ack (M) Stop (M) (M) => SDA Controlled by Master (S) => SDA Controlled by Slave Figure 5-33. I2C Read In the case of an I2C register write, if the master does not issue a STOP condition, then the device enters auto-increment mode. So in the next eight clocks, the data on SDA is treated as data for the next incremental register. Similarly, in the case of an I2C register read, after the device has sent out the 8-bit data from the addressed register, if the master issues a ACKNOWLEDGE, the slave takes over control of SDA bus and transmit for the next 8 clocks the data of the next incremental register. 56 APPLICATION INFORMATION Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 6 REGISTER MAP 6.1 TLV320DAC3120 Register Map All features on this device are addressed using the I2C bus. All of the writable registers can be read back. However, some registers contain status information or data, and are available for reading only. The TLV320DAC3120 contains several pages of 8-bit registers, and each page can contain up to 128 registers. The register pages are divided up based on functional blocks for this device. Page 0 is the default home page after RESET. Page control is done by writing a new page value into register 0 of the current page. The control registers for the TLV320DAC3120 are described in detail as follows. All registers are 8 bits in width, with D7 referring to the most-significant bit of each register, and D0 referring to the least-significant bit. Pages 0, 1, 3, 8–11, 12–15, and 64–95 are available for use; however, all other pages and registers are reserved. Do not read from or write to reserved pages and registers. Also, do not write other than the reset values for the reserved bits and read-only bits of non-reserved registers; otherwise, device functionality failure can occur. Table 6-1. Summary of Register Map Page Number 6.2 Description 0 Page 0 is the default page on power up. Configuration for serial interface, digital I/O, clocking, DAC settings, etc. 1 Configuration for analog DAC, output drivers, volume controls, etc. 3 Register 16 controls the MCLK divider that controls the interrupt pulse duration, debounce timing, and detection block clock. 8–11 DAC buffer-A filter and DRC coefficients, miniDSP general-purpose buffer-A coefficients 12–15 DAC buffer-B filter and DRC coefficients, miniDSP general-purpose buffer B-coefficients 64–95 DAC instuction RAM locations Control Registers, Page 0 (Default Page): Clock Multipliers, Dividers, Serial Interfaces, Flags, Interrupts, and GPIOs Page 0 / Register 0: Page Control Register BIT D7–D0 READ/ WRITE R/W RESET VALUE 0000 0000 DESCRIPTION 0000 0000: 0000 0001: ... 1111 1110: 1111 1111: Page 0 selected Page 1 selected Page 254 selected Page 255 selected Page 0 / Register 1: Software Reset BIT D7–D1 D0 READ/ WRITE R/W R/W RESET VALUE 0000 000 0 READ/ WRITE R RESET VALUE XXXX XXXX DESCRIPTION Reserved. Write only zeros to these bits. 0: Don't care 1: Self-clearing software reset for control register Page 0 / Register 2: Reserved BIT D7–D0 DESCRIPTION Reserved. Do not write to this register. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 57 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 0 / Register 3: OT FLAG D7-D2 D1 READ/ WRITE R R RESET VALUE XXXX XX 1 D0 R/W X BIT DESCRIPTION Reserved. Do not write to these bits. 0: Overtemperature protection flag (active-low). Valid only if speaker amplifier is powered up 1: Normal operation Reserved. Do not write to these bits. Page 0 / Register 4: Clock-Gen Muxing (1) D7–D4 D3–D2 READ/ WRITE R/W R/W RESET VALUE 0000 00 D1–D0 R/W 00 BIT (1) DESCRIPTION Reserved. Write only zeros to these bits. 00: PLL_CLKIN = MCLK (device pin) 01: PLL_CLKIN = BCLK (device pin) 10: PLL_CLKIN = GPIO1 (device pin) 11: PLL_CLKIN = DIN (can be used for the system where DAC is not used) 00: CODEC_CLKIN = MCLK (device pin) 01: CODEC_CLKIN = BCLK (device pin) 10: CODEC_CLKIN = GPIO1 (device pin) 11: CODEC_CLKIN = PLL_CLK (generated on-chip) See Section 5.7 for more details on clock generation mutiplexing and dividers. Page 0 / Register 5: PLL P and R-VAL D7 READ/ WRITE R/W RESET VALUE 0 D6–D4 R/W 001 D3–D0 R/W 0001 READ/ WRITE R/W R/W RESET VALUE 00 00 0100 BIT DESCRIPTION 0: PLL is powered down. 1: PLL is powered up. 000: PLL divider P = 8 001: PLL divider P = 1 010: PLL divider P = 2 ... 110: PLL divider P = 6 111: PLL divider P = 7 0000: PLL multiplier R = 16 0001: PLL multiplier R = 1 0010: PLL multiplier R = 2 ... 1110: PLL multiplier R = 14 1111: PLL multiplier R = 15 Page 0 / Register 6: PLL J-VAL BIT D7–D6 D5–D0 DESCRIPTION Reserved. Write only zeros to these bits. 00 0000: Do not use (reserved) 00 0001: PLL multiplier J = 1 00 0010: PLL multiplier J = 2 ... 11 1110: PLL multiplier J = 62 11 1111: PLL multiplier J = 63 Table 6-2. Page 0 / Register 7: PLL D-VAL MSB (1) BIT D7–D6 D5–D0 (1) 58 READ/ WRITE R/W R/W RESET VALUE 00 00 0000 DESCRIPTION Reserved. Write only zeros to these bits. PLL fractional multiplier D-Val MSB bits D[13:8] Note that this register will be updated only when page 0 / Register 8 is written immediately after page 0 / Register 7. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Page 0 / Register 8: PLL D-VAL LSB (1) BIT D7–D0 (1) READ/ WRITE R/W RESET VALUE 0000 0000 DESCRIPTION PLL fractional multiplier D-Val LSB bits D[7:0] Note that page 0 / Register 8 must be written immediately after page 0 / Register 7. Page 0 / Registers 9–10: Reserved READ/ WRITE R/W RESET VALUE XXXX XXXX D7 READ/ WRITE R/W RESET VALUE 0 D6–D0 R/W 000 0001 D7 READ/ WRITE R/W RESET VALUE 0 D6–D0 R/W 000 0001 BIT D7–D0 DESCRIPTION Reserved. Write only zeros to these bits. Page 0 / Register 11: DAC NDAC_VAL BIT DESCRIPTION 0: DAC NDAC divider is powered down. 1: DAC NDAC divider is powered up. 000 0000: DAC NDAC divider = 128 000 0001: DAC NDAC divider = 1 000 0010: DAC NDAC divider = 2 ... 111 1110: DAC NDAC divider = 126 111 1111: DAC NDAC divider = 127 Page 0 / Register 12: DAC MDAC_VAL BIT DESCRIPTION 0: DAC MDAC divider is powered down. 1: DAC MDAC divider is powered up. 000 0000: DAC MDAC divider = 128 000 0001: DAC MDAC divider = 1 000 0010: DAC MDAC divider = 2 ... 111 1110: DAC MDAC divider = 126 111 1111: DAC MDAC divider = 127 Page 0 / Register 13: DAC DOSR_VAL MSB BIT D7–D2 D1–D0 READ/ WRITE R/W R/W RESET VALUE 0000 00 00 DESCRIPTION Reserved DAC OSR value DOSR(9:8) Page 0 / Register 14: DAC DOSR_VAL LSB (1) BIT D7–D0 (1) (2) READ/ WRITE R/W RESET VALUE 1000 0000 (2) DESCRIPTION DAC OSR Value DOSR(7:0) 0000 0000: DAC OSR(7:0) = 1024 (MSB page 0 / register 13, bits D1–D0 = 00) 0000 0001: DAC OSR(7:0) = 1(MSB page 0 / register 13, bits D1–D0 = 00) 0000 0010: DAC OSR(7:0) = 2 (MSB page 0 / register 13, bits D1–D0 = 00) ... 1111 1110: DAC OSR(7:0) = 1022 (MSB page 0 / register 13, bits D1–D0 = 11) 1111 1111: DAC OSR(7:0) = 1023 (MSB page 0 / register 13, bits D1–D0 = 11) DAC OSR should be an integral multiple of the interpolation in the DAC miniDSP engine (specified in register 16). Note that page 0 / register 14 must be written to immediately after writing to page 0 / register 13. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 59 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 0 / Register 15: DAC IDAC_VAL (1) BIT D7–D0 (1) READ/ WRITE R/W RESET VALUE 1000 0000 DESCRIPTION 0000 0000: 0000 0001: 0000 0010: ... 1111 1101: 1111 1110: 1111 1111: Number of instruction for DAC miniDSP engine, IDAC = 1024 Number of instruction for DAC miniDSP engine, IDAC = 4 Number of instruction for DAC miniDSP engine, IDAC = 8 Number of instruction for DAC miniDSP engine, IDAC = 1012 Number of instruction for DAC miniDSP engine, IDAC = 1016 Number of instruction for DAC miniDSP engine, IDAC = 1020 IDAC should be an integral multiple of the interpolation in the DAC miniDSP engine (specified in register 16). Page 0 / Register 16: DAC miniDSP Engine Interpolation BIT D7–D4 D3–D0 READ/ WRITE R/W R/W RESET VALUE 0000 1000 DESCRIPTION Reserved. Do not write to these registers. 0000: Interpolation ratio in DAC miniDSP engine 0001: Interpolation ratio in DAC miniDSP engine 0010: Interpolation ratio in DAC miniDSP engine ... 1101: Interpolation ratio in DAC miniDSP engine 1110: Interpolation ratio in DAC miniDSP engine 1111: Interpolation ratio in DAC miniDSP engine = 16 =1 =2 = 13 = 14 = 15 Page 0 / Registers 17–24: Reserved READ/ WRITE R/W RESET VALUE XXXX XXXX READ/ WRITE R/W R/W RESET VALUE 0000 0 000 D7 READ/ WRITE R/W RESET VALUE 0 D6–D0 R/W 000 0001 BIT D7–D0 DESCRIPTION Reserved. Do not write to these registers. Page 0 / Registers 25: CLKOUT MUX BIT D7–D3 D2–D0 DESCRIPTION Reserved 000: CDIV_CLKIN = MCLK (device pin) 001: CDIV_CLKIN = BCLK (device pin) 010: CDIV_CLKIN = DIN (can be used for the systems where DAC is not required) 011: CDIV_CLKIN = PLL_CLK (generated on-chip) 100: CDIV_CLKIN = DAC_CLK (DAC DSP clock - generated on-chip) 101: CDIV_CLKIN = DAC_MOD_CLK (generated on-chip) 110: Reserved 111: Reserved Page 0 / Registers 26: CLKOUT M_VAL BIT 60 DESCRIPTION 0: CLKOUT M divider is powered down. 1: CLKOUT M divider is powered up. 000 0000: CLKOUT divider M = 128 000 0001: CLKOUT divider M = 1 000 0010: CLKOUT divider M = 2 ... 111 1110: CLKOUT divider M = 126 111 1111: CLKOUT divider M = 127 REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Page 0 / Register 27: Codec Interface Control D7–D6 READ/ WRITE R/W RESET VALUE 00 D5–D4 R/W 00 D3 R/W 0 D2 R/W 0 D1 D0 R/W R/W 0 0 READ/ WRITE R/W RESET VALUE 0000 0000 D7–D6 D5 D4 D3 READ/ WRITE R/W R/W R/W R/W RESET VALUE 00 0 0 0 D2 R/W 0 D1–D0 R/W 00 D7 READ/ WRITE R/W RESET VALUE 0 D6–D0 R/W 000 0001 BIT DESCRIPTION 00: Codec interface = I2S 01: Codec Interface = DSP 10: Codec interface = RJF 11: Codec interface = LJF 00: Codec interface word length = 16 01: Codec interface word length = 20 10: Codec interface word length = 24 11: Codec interface word length = 32 0: BCLK is input. 1: BCLK is output. 0: WCLK is input. 1: WCLK is output. Reserved Reserved bits bits bits bits Page 0 / Register 28: Data-Slot Offset Programmability BIT D7–D0 DESCRIPTION Offset (Measured With Respect to WCLK Rising Edge in DSP Mode) 0000 0000: Offset = 0 BCLKs 0000 0001: Offset = 1 BCLK 0000 0010: Offset = 2 BCLKs ... 1111 1110: Offset = 254 BCLKs 1111 1111: Offset = 255 BCLKs Page 0 / Register 29: Codec Interface Control 2 BIT DESCRIPTION Reserved Reserved Reserved 0: BCLK is not inverted (valid for both primary and secondary BCLK). 1: BCLK is inverted (valid for both primary and secondary BCLK). BCLK and WCLK Active Even With Codec Powered Down (Valid for Both Primary and Secondary BCLK) 0: Disabled 1: Enabled 00: BDIV_CLKIN = DAC_CLK (DAC DSP clock - generated on-chip) 01: BDIV_CLKIN = DAC_MOD_CLK (generated on-chip) 10: Reserved 11: Reserved Page 0 / Register 30: BCLK N_VAL BIT DESCRIPTION 0: BCLK N-divider is powered down. 1: BCLK N-divider is powered up. 000 0000: BCLK divider N = 128 000 0001: BCLK divider N = 1 000 0010: BCLK divider N = 2 ... 111 1110: BCLK divider N = 126 111 1111: BCLK divider N = 127 REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 61 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 0 / Register 31: Codec Secondary Interface Control 1 D7–D5 READ/ WRITE R/W RESET VALUE 000 D4–D2 R/W 000 D1–D0 R/W 00 BIT DESCRIPTION 000: Secondary BCLK is obtained from GPIO1 pin. 001–111: Reserved. 000: Secondary WCLK is obtained from GPIO1 pin. 001–111: Reserved. 00: Secondary DIN is obtained from the GPIO1 pin. 01–11: Reserved.10: Reserved. Page 0 / Register 32: Codec Secondary Interface Control 2 D7–D4 D3 READ/ WRITE R/W R/W RESET VALUE 0000 0 D2 R/W 0 D1 D0 R/W R/W 0 0 D7 READ/ WRITE R/W RESET VALUE 0 D6 R/W 0 D5–D4 R/W 00 D3–D2 R/W 00 D1 D0 R/W R/W 0 0 BIT DESCRIPTION Reserved 0: Primary BCLK is fed to codec serial-interface and ClockGen blocks. 1: Secondary BCLK is fed to codec serial-interface and ClockGen blocks. 0: Primary WCLK is fed to codec serial-interface block. 1: Secondary WCLK is fed to codec serial-interface block. Reserved 0: Primary DIN is fed to codec serial-interface block. 1: Secondary DIN is fed to codec serial-interface block. Page 0 / Register 33: Codec Secondary Interface Control 3 BIT DESCRIPTION 0: Primary BCLK output = internally generated BCLK clock 1: Primary BCLK output = secondary BCLK 0: Secondary BCLK output = primary BCLK 1: Secondary BCLK output = internally generated BCLK clock 00: Primary WCLK output = internally generated DAC_fS 01: Reserved 10: Primary WCLK output = secondary WCLK 11: Reserved 00: Secondary WCLK output = primary WCLK 01: Secondary WCLK output = internally generated DAC_fS clock 10: Reserved 11: Reserved Reserved Reserved Page 0 / Register 34: I2C Bus Condition D7–D6 D5 READ/ WRITE R/W R/W RESET VALUE 00 0 D4–D0 R/W 0 0000 BIT DESCRIPTION Reserved. Write only the reset value to these bits. 0: I2C general-call address is ignored. 1: Device accepts I2C general-call address. Reserved. Write only zeros to these bits. Page 0 / Register 35 Through Page 0 / Register 36: Reserved BIT D7– 62 READ/ WRITE R RESET VALUE XXXX XXXX DESCRIPTION Reserved. Write only zeros to these bits. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Page 0 / Register 37: DAC Flag Register D7 READ/ WRITE R RESET VALUE 0 D6 D5 R/W R X 0 D4 R 0 D3 D2 D1 D0 R R/W R R 0 X 0 0 BIT DESCRIPTION 0: DAC powered down 1: DAC powered up Reserved. Write only zero to this bit. 0: HPOUT driver powered down 1: HPOUT driver powered up 0: Class-D driver powered down 1: Class-D driver powered up Reserved. Reserved. Write only zero to this bit. Reserved. Reserved. Page 0 / Register 38: DAC Flag Register D7–D5 D4 READ/ WRITE R/W R RESET VALUE XXX 0 D3–D1 D0 R/W R XXX 0 BIT DESCRIPTION Reserved. Do not write to these bits. 0: DAC PGA applied gain ≠ programmed gain 1: DAC PGA applied gain = programmed gain Reserved. Write only zeros to these bits. Reserved. Page 0 / Register 39: Overflow Flags READ/ WRITE R RESET VALUE 0 D6 (1) D5 (1) R R 0 0 D4 D3 D2 D1 D0 R/W R R/W R R/W 0 0 0 0 0 BIT D7 (1) (1) DESCRIPTION DAC Overflow Flag 0: Overflow has not occurred. 1: Overflow has occurred. Reserved. DAC Barrel Shifter Output Overflow Flag 0: Overflow has not occurred. 1: Overflow has occurred. Reserved. Write only zeros to these bits. Reserved. Write only zeros to these bits. Reserved. Write only zero to this bit. Reserved. Write only zeros to these bits. Reserved. Write only zero to this bit. Sticky flag bIts. These are read-only bits. They are automatically cleared once they are read and are set only if the source trigger occurs again. Page 0 / Registers 40–43: Reserved BIT D7–D0 READ/ WRITE R/W RESET VALUE XXXX XXXX DESCRIPTION Reserved. Write only the reset value to these bits. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 63 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 0 / Register 44: Interrupt Flags—DAC D7 (1) READ/ WRITE R RESET VALUE 0 D6 (1) D5 (1) R R 0 X D4 (1) R X D3 (1) R 0 D2 (1) D1 (1) R R 0 0 D0 (1) R 0 BIT (1) DESCRIPTION 0: No short circuit is detected at HPOUT / class-D driver. 1: Short circuit is detected at HPOUT / class-D driver. Reserved 0: No headset button pressed 1: Headset button pressed 0: No headset insertion/removal is detected. 1: Headset insertion/removal is detected. 0: DAC signal power is les than or equal to the signal threshold of DRC. 1: DAC signal power is above the signal threshold of DRC. Reserved. DAC miniDSP Engine Standard Interrupt-Port Output 0: Read a 0 from Standard Interrupt-Port 1: Read a 1 from Standard Interrupt-Port DAC miniDSP Engine Auxilliary Interrupt-Port Output 0: Read a 0 from Auxilliary Interrupt-Port 1: Read a 1 from Auxilliary Interrupt-Port Sticky flag bIts. These are read-only bits. They are automatically cleared once they are read and are set only if the source trigger occurs again. Page 0 / Register 45: Reserved READ/ WRITE R/W RESET VALUE XXXX XXXX D7 READ/ WRITE R RESET VALUE 0 D6 D5 R R 0 X D4 R X D3 R 0 D2 D1 R R 0 0 D0 R 0 READ/ WRITE R/W RESET VALUE XXXX XXXX BIT D7–D0 DESCRIPTION Reserved. Write only the reset value to these bits. Page 0 / Register 46: Interrupt Flags – DAC BIT DESCRIPTION 0: No short circuit detected at HPOUT / class-D driver 1: Short circuit detected at HPOUT / class-D driver Reserved 0: No headset button pressed 1: Headset button pressed 0: Headset removal detected 1: Headset insertion detected 0: DAC signal power is below signal threshold of DRC. 1: DAC signal power is above signal threshold of DRC. Reserved. DAC miniDSP Engine Standard Interrupt Port Output 0: Read a 0 from Standard Interrupt-Port 1: Raed a 1 from Standard Interrupt-Port DAC miniDSP Engine Auxiliary Interrupt Port Output 0: Read a 0 from Auxilliary Interrupt-Port 1: Read a 1 from Auxilliary Interrupt-Port Page 0 / Register 47: Reserved BIT D7–D0 64 DESCRIPTION Reserved. Write only the reset value to these bits. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Page 0 / Register 48: INT1 Control Register D7 READ/ WRITE R/W RESET VALUE 0 D6 R/W 0 D5 R/W 0 D4 D3 R/W R/W 0 0 D2 R/W 0 D1 D0 R/W R/W 0 0 BIT DESCRIPTION 0: Headset-insertion detect interrupt is not used in the generation of INT1 interrupt. 1: Headset-insertion detect interrupt is used in the generation of INT1 interrupt. 0: Button-press detect interrupt is not used in the generation of INT1 interrupt. 1: Button-press detect interrupt is used in the generation of INT1 interrupt. 0: DAC DRC signal-power interrupt is not used in the generation of INT1 interrupt. 1: DAC DRC signal-power interrupt is used in the generation of INT1 interrupt. Reserved 0: Short-circuit interrupt is not used in the generation of INT1 interrupt. 1: Short-circuit interrupt is used in the generation of INT1 interrupt. 0: Engine-generated interrupt is not used in the generation of INT1 interrupt. 1: Engine-generated interrupt is used in the generation of INT1 interrupt. Reserved 0: INT1 is only one pulse (active-high) of typical 2-ms duration. 1: INT1 is multiple pulses (active-high) of typical 2-ms duration and 4-ms period, until flag registers 44 and 45 are read by the user. Page 0 / Register 49: INT2 Control Register D7 READ/ WRITE R/W RESET VALUE 0 D6 R/W 0 D5 R/W 0 D4 D3 R/W R/W 0 0 D2 R/W 0 D1 D0 R/W R/W 0 0 READ/ WRITE R/W RESET VALUE 0000 0000 BIT DESCRIPTION 0: Headset-insertion detect interrupt is not used in the generation of INT2 interrupt. 1: Headset-insertion detect interrupt is used in the generation of INT2 interrupt. 0: Button-press detect interrupt is not used in the generation of INT2 interrupt. 1: Button-press detect interrupt is used in the generation of INT2 interrupt. 0: DAC DRC signal-power interrupt is not used in the generation of INT2 interrupt. 1: DAC DRC signal-power interrupt is used in the generation of INT2 interrupt. Reserved 0: Short-circuit interrupt is not used in the generation of INT2 interrupt. 1: Short-circuit interrupt is used in the generation of INT2 interrupt. 0: Engine-generated interrupt is not used in the generation of INT2 interrupt. 1: Engine-generated interrupt is used in the generation of INT2 interrupt. Reserved 0: INT2 is only one pulse (active-high) of typical 2-ms duration. 1: INT2 is multiple pulses (active-high) of typical 2-ms duration and 4-ms period, until flag registers 44 and 45 are read by the user. Page 0 / Register 50: Reserved BIT D7-D0 DESCRIPTION Reserved. Write only reset values. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 65 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 0 / Register 51: GPIO1 In/Out Pin Control D7–D6 D5–D2 READ/ WRITE R/W R/W RESET VALUE XX 0000 D1 D0 R R/W X 0 READ/ WRITE R/W RESET VALUE XX READ/ WRITE R/W RESET VALUE 0000 1001 D7–D3 D2–D1 READ/ WRITE R/W R/W RESET VALUE 0000 0 01 D0 R X READ/ WRITE R/W RESET VALUE 0000 0000 READ/ WRITE R/W RESET VALUE XXXX XXXX BIT DESCRIPTION Reserved. Do not write any value other than reset value. 0000: GPIO1 disabled (input and output buffers powered down) 0001: GPIO1 is in input mode (can be used as secondary BCLK input, secondary WCLK input, secondary DIN input, input or in ClockGen block). 0010: GPIO1 is used as general-purpose input (GPI). 0011: GPIO1 output = general-purpose output 0100: GPIO1 output = CLKOUT output 0101: GPIO1 output = INT1 output 0110: GPIO1 output = INT2 output 0111: Reserved 1000: GPIO1 output = secondary BCLK output for codec interface 1001: GPIO1 output = secondary WCLK output for codec interface 1010: Reserved 1011: Reserved 1100: Reserved 1101: Reserved 1110: Reserved 1111: Reserved GPIO1 input buffer value 0: GPIO1 general-purpose output value = 0 1: GPIO1 general-purpose output value = 1 Page 0 / Register 52: Reserved BIT D7–D0 DESCRIPTION Reserved. Do not write any value other than reset value. Page 0 / Register 53: Reserved BIT D7–D0 DESCRIPTION Reserved Page 0 / Register 54: DIN (IN Pin) Control BIT DESCRIPTION Reserved 00: DIN disabled (input buffer powered down) 01: DIN enabled (can be used as DIN for codec interface or in ClockGen block) 10: DIN is used as general-purpose input (GPI) 11: Reserved DIN input-buffer value Page 0 / Register 55 Through Page 0 / Register 58: Reserved BIT D7–D0 DESCRIPTION Reserved Page 0 / Register 59: Reserved BIT D7–D0 66 DESCRIPTION Reserved. Write only zeros to these bits. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Page 0 / Register 60: DAC Instruction Set BIT D7–D5 D4–D0 READ/ WRITE R/W R/W RESET VALUE 000 0 0001 READ/ WRITE R/W RESET VALUE 0000 1000 READ/ WRITE R/W R/W R/W R/W R/W R/W R/W R/W RESET VALUE 0 0 0 0 0 0 0 0 DESCRIPTION Reserved. Write only default value. 0 0000: DAC miniDSP is used for signal processing. 0 0001–0 0011: Reserved. Do not use 0 0100: DAC signal-processing block PRB_P4 0 0101: DAC signal-processing block PRB_P5 0 0110: DAC signal-processing block PRB_P6 0 0111–0 1011: Reserved. Do not use 0 1100: DAC signal-processing block PRB_P12 0 1101: DAC signal-processing block PRB_P13 0 1110: DAC signal-processing block PRB_P14 0 1111: DAC signal-processing block PRB_P15 1 0000: DAC signal-processing block PRB_P16 1 0001–1 0011: Reserved. Do not use. 1 0100: DAC signal-processing block PRB_P20 1 0101: DAC signal-processing block PRB_P21 1 0110: DAC signal-processing block PRB_P22 1 0111–1 1000: Reserved. Do not use. 11001: DAC Signal Processing Block PRB_P25 11010–11111: Reserved. Do not use. Page 0 / Register 61:Reserved BIT D7–D0 DESCRIPTION Reserved. Write only default values. Page 0 / Register 62: Programmable Instruction Mode-Control Bits BIT D7 D6 D5 D4 D3 D2 D1 D0 DESCRIPTION Reserved Reserved Reserved Reserved Reserved DAC miniDSP engine auxiliary control bit A, which can be used for conditional instructions like JMP DAC miniDSP engine auxiliary control bit B, which can be used for conditional instructions like JMP 0: Reset DAC miniDSP instruction counter at the start of the new frame. 1: Do not reset DAC miniDSP instruction counter at the start of the new frame. Page 0 / Register 63: DAC Data-Path Setup D7 READ/ WRITE R/W RESET VALUE 0 D6 D5–D4 R/W R/W 0 01 D3–D2 D1–D0 R/W R/W 01 00 BIT DESCRIPTION 0: DAC is powered down. 1: DAC is powered up. Reserved. 00: DAC data path = off 01: DAC data path = left data 10: DAC data path = right data 11: DAC data path = left and right data ((L + R)/2) Reserved. 00: DAC channel volume control soft-stepping is enabled for one step per sample period. 01: DAC channel volume control soft-stepping is enabled for one step per two sample periods. 10: DAC channel volume control soft-stepping is disabled. 11: Reserved. Do not write this sequence to these bits. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 67 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 0 / Register 64: DAC VOLUME CONTROL D7–D4 D3 READ/ WRITE R/W R/W RESET VALUE 0000 1 D2 D1–D0 R/W R/W 1 00 READ/ WRITE R/W RESET VALUE 0000 0000 READ/ WRITE R/W RESET VALUE 0000 0000 D7 READ/ WRITE R/W RESET VALUE 0 D6–D5 R XX D4–D2 R/W 000 D1–D0 R/W 00 BIT DESCRIPTION Reserved. Write only zeros to these bits. 0: DAC not muted 1: DAC muted Reserved. Reserved. Always write reset value. Page 0 / Register 65: DAC Volume Control BIT D7–D0 DESCRIPTION 127 to 49: Reserved. Do not write these sequences to these bits. 48: DAC Digital gain = 24 dB 47: DAC Digital gain = 23.5 dB 46: DAC Digital gain = 23 dB ... 36: DAC Digital gain = 18 dB 35: DAC Digital gain = 17.5 dB 34: DAC Digital gain = 17 dB ... 1: DAC Digital gain = 0.5 dB 0: DAC Digital gain = 0 dB –1: DAC Digital gain = –0.5 dB ... –126: DAC Digital gain = –63 dB –127: DAC Digital gain = –63.5 dB –128: Reserved Page 0 / Register 66: Reserved BIT D7–D0 DESCRIPTION Reserved. write only reset values. Page 0 / Register 67: Headset Detection BIT (1) 68 DESCRIPTION 0: Headset detection disabled 1: Headset detection enabled 00: No headset detected 01: Headset without microphone is detected 10: Reserved 11: Headset with microphone is detected Debounce Programming for Glitch Rejection During Headset Detection (1) 000: 16 ms (sampled with 2-ms clock) 001: 32 ms (sampled with 4-ms clock) 010: 64 ms (sampled with 8-ms clock) 011: 128 ms (sampled with 16-ms clock) 100: 256 ms (sampled with 32-ms clock) 101: 512 ms (sampled with 64-ms clock) 110: Reserved 111: Reserved Debounce Programming for Glitch Rejection During Headset Button-Press Detection 00: 0 ms 01: 8 ms (sampled with 1-ms clock) 10: 16 ms (sampled with 2-ms clock) 11: 32 ms (sampled with 4-ms clock) Note that these times are generated using the 1 MHz reference clock which is defined in page 3 / register 16. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Page 0 / Register 68: DRC Control 1 D7 D6 READ/ WRITE R/W R/W RESET VALUE 0 0 D5 D4–D2 R/W R/W 0 011 D1–D0 R/W 11 BIT DESCRIPTION Reserved. Write only the reset value to these bits. 0: DRC disabled 1: DRC enabled Reserved. Write only reset value. 000: DRC threshold = –3 dB 001: DRC threshold = –6 dB 010: DRC threshold = –9 dB 011: DRC threshold = –12 dB 100: DRC threshold = –15 dB 101: DRC threshold = –18 dB 110: DRC threshold = –21 dB 111: DRC threshold = –24 dB 00: DRC hysteresis = 0 dB 01: DRC hysteresis = 1 dB 10: DRC hysteresis = 2 dB 11: DRC hysteresis = 3 dB Page 0 / Register 69: DRC Control 2 BIT D D6–D3 READ/ WRITE R R/W D2-D0 RESET VALUE 0 0111 000 DESCRIPTION Reserved. Write only the reset value to these bits. DRC Hold Programmability 0000: DRC Hold Disabled 0001:DRC Hold Time = 32 DAC Word Clocks 0010: DRC Hold Time = 64 DAC Word Clocks 0011: DRC Hold Time = 128 DAC Word Clocks 0100: DRC Hold Time = 256 DAC Word Clocks 0101: DRC Hold Time = 512 DAC Word Clocks ... 1110: DRC Hold Time = 4*32768 DAC Word Clocks 1111: DRC Hold Time = 5*32768 DAC Word Clocks Reserved. Write only the reset value to these bits. Page 0 / Register 70: DRC Control 3 BIT D7–D4 D3–D0 READ/ WRITE R/W R/W RESET VALUE 0000 0000 DESCRIPTION 0000: 0001: 0010: ... 1110: 1111: 0000: 0001: 0010: ... 1110: 1111: DRC attack rate = 4 dB per DAC Word Clock DRC attack rate = 2 dB per DAC Word Clock DRC attack rate = 1 dB per DAC Word Clock DRC DRC DRC DRC DRC attack rate = 2.4414e–5 attack rate = 1.2207e–5 decay rate = 1.5625e–2 decay rate = 7.8125e–3 decay rate = 3.9062e–3 dB per dB per dB per dB per dB per DAC DAC DAC DAC DAC Word Clock Word Clock Word Clock Word Clock Word Clock DRC decay rate = 9.5367e–7 dB per DAC Word Clock DRC decay rate = 4.7683e–7 dB per DAC Word Clock REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 69 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 0 / Register 71 (0x47): Beep Generator D7 READ/ WRITE R/W RESET VALUE 0 D6 D5–D0 R/W R/W 0 00 0000 BIT (1) (1) DESCRIPTION 0: Beep generator is disabled. 1: Beep generator is enabled (self-clearing based on beep duration). Reserved. Write only reset value. 00 0000: Beep volume control = 2 dB 00 0001: Beep volume control = 1 dB 00 0010: Beep volume control = 0 dB 00 0011: Beep volume control = –1 dB ... 11 1110: Beep volume control = –60 dB 11 1111: Beep volume control = –61 dB The beep generator is only available in PRB_P25 DAC processing mode. Page 0 / Register 72: Reserved BIT D7–D0 READ/ WRITE R/W RESET VALUE 0 READ/ WRITE R/W RESET VALUE 0000 0000 READ/ WRITE R/W RESET VALUE 0000 0000 READ/ WRITE R/W RESET VALUE 1110 1110 READ/ WRITE R/W RESET VALUE 0001 0000 READ/ WRITE R/W RESET VALUE 1101 1000 READ/ WRITE R/W RESET VALUE 0111 1110 READ/ WRITE R/W RESET VALUE 1110 0011 DESCRIPTION Reserved. Page 0 / Register 73 (0x49): Beep Length MSB BIT D7–D0 DESCRIPTION 8 MSBs out of 24 bits for the number of samples for which the beep must be generated. Page 0 / Register 74 (0x4A): Beep Length Middle Bits BIT D7–D0 DESCRIPTION 8 middle bits out of 24 bits for the number of samples for which the beep must be generated. Page 0 / Register 75 (0x4B): Beep Length LSB BIT D7–D0 DESCRIPTION 8 LSBs out of 24 bits for the number of samples for which beep need to be generated. Page 0 / Register 76 (0x4C): Beep Sin(x) MSB BIT D7–D0 DESCRIPTION 8 MSBs out of 16 bits for sin(2π × fin/fS), where fin is the beep frequency and fS is the DAC sample rate. Page 0 / Register 77 (0x4D): Beep Sin(x) LSB BIT D7–D0 DESCRIPTION 8 LSBs out of 16 bits for sin(2π × fin/fS), where fin is the beep frequency and fS is the DAC sample rate. Page 0 / Register 78 (0x4E): Beep Cos(x) MSB BIT D7–D0 DESCRIPTION 8 MSBs out of 16 bits for cos(2π × fin/fS), where fin is the beep frequency and fS is the DAC sample rate. Page 0 / Register 79 (0x4F): Beep Cos(x) LSB BIT D7–D0 70 DESCRIPTION 8 LSBs out of 16 bits for cos(2π × fin/fS), where fin is the beep frequency and fS is the DAC sample rate. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Page 0 / Register 80-115: Reserved READ/ WRITE R/W RESET VALUE 0 D7 READ/ WRITE R/W RESET VALUE 0 D6 R/W 0 D5–D4 R/W 00 D3 D2–D0 R/W R/W 0 000 READ/ WRITE R/W R RESET VALUE 0 XXX XXXX BIT D7–D0 DESCRIPTION Reserved. Page 0 / Register 116: VOL/MICDET-Pin SAR ADC – Volume Control BIT DESCRIPTION 0: DAC volume control is controlled by control register. (7-bit Vol ADC is powered down) 1: DAC volume control is controlled by pin. 0: Internal on-chip RC oscillator is used for the 7-bit Vol ADC for pin volume control. 1: MCLK is used for the 7-bit Vol ADC for pin volume control. 00: No hysteresis for volume control ADC output 01: Hysteresis of ±1 bit 10: Hysteresis of ±2 bits 11: Reserved. Do not write this sequence to these bits. Reserved. Write only reset value. Throughput of the 7-bit Vol ADC for pin volume control, frequency based on MCLK or internal oscillator. MCLK = 12 MHz Internal Oscillator Source 000: Throughput = 15.625 Hz 10.68 Hz 001: Throughput = 31.25 Hz 21.35 Hz 010: Throughput = 62.5 Hz 42.71 Hz 011: Throughput = 125 Hz 8.2 Hz 100: Throughput = 250 Hz 170 Hz 101: Throughput = 500 Hz 340 Hz 110: Throughput = 1 kHz 680 Hz 111: Throughput = 2 kHz 1.37 kHz Note: These values are based on a nominal oscillator frequency of 8.2 MHz. Values will scale to the actual oscillator frequency. Page 0 / Register 117: VOL/MICDET-Pin Gain BIT D7 D6–D0 DESCRIPTION Reserved. Write only zero to this bit. 000 0000: Gain applied by pin volume control 000 0001: Gain applied by pin volume control 000 0010: Gain applied by pin volume control ... 010 0011: Gain applied by pin volume control 010 0100: Gain applied by pin volume control 010 0101: Gain applied by pin volume control ... 101 1001: Gain applied by pin volume control 101 1010: Gain applied by pin volume control 101 1011: Gain applied by pin volume control ... 111 1101: Gain applied by pin volume control 111 1110: Gain applied by pin volume control 111 1111: Reserved. = 18 dB = 17.5 dB = 17 dB = 0.5 dB = 0 dB = –0.5 dB = –26.5 dB = –27 dB = –28 dB = –62 dB = –63 dB Page 0 / Registers 118 to 127: Reserved BIT D7–D0 6.3 READ/ WRITE R/W RESET VALUE XXXX XXXX DESCRIPTION Reserved. Do not write to these registers. Control Registers, Page 1: DAC Routing, Power-Controls and MISC Logic Related Programmabilities REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 71 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 1 / Register 0: Page Control Register BIT D7–D0 READ/ WRITE R/W RESET VALUE 0000 0000 DESCRIPTION 0000 0000: 0000 0001: ... 1111 1110: 1111 1111: Page 0 selected Page 1 selected Page 254 selected Page 255 selected Page 1 / Registers 1–29: Reserved READ/ WRITE R/W RESET VALUE XXXX XXXX D7–D2 READ/ WRITE R/W RESET VALUE 0000 00 D1 R/W 0 D0 R/W 0 BIT D7–D0 DESCRIPTION Reserved. Do not write to these registers. Page 1 / Register 30: Headphone and Speaker Amplifier Error Control BIT DESCRIPTION Reserved 0: Reset HPOUT power-up control bit on short-circuit detection if page-1, register 31, D1 = 1. 1: HPOUT power-up control bits remain unchanged on short-circuit detection. 0: Reset SPL and SPR power-up control bits on short-circuit detection. 1: SPL and SPR power-up control bits remain unchanged on short-circuit detection. Page 1 / Register 31: Headphone Drivers D7 READ/ WRITE R/W RESET VALUE 0 D6 D5 D4–D3 R/W R/W R/W 0 0 0 D2 D1 R/W R/W 1 0 D0 R 0 D7 READ/ WRITE R/W RESET VALUE 0 D6 D5–D1 D0 R/W R/W R 0 00 011 0 BIT DESCRIPTION 0: HPOUT output driver is powered down. 1: HPOUT output driver is powered up. Reserved Reserved. Write only zero to this bit. 00: Output common-mode voltage = 1.35 V 01: Output common-mode voltage = 1.5 V 10: Output common-mode voltage = 1.65 V 11: Output common-mode voltage = 1.8 V Reserved. Write only 1 to this bit. 0: If short-circuit protection is enabled for headphone driver and short circuit detected, device limits the maximum current to the load. 1: If short-circuit protection is enabled for headphone driver and short circuit detected, device powers down the output driver. 0: Short circuit is not detected on the headphone driver. 1: Short circuit is detected on the headphone driver. Page 1 / Register 32: Class-D Speaker Amplifier BIT 72 DESCRIPTION 0: Class-D output driver is powered down. 1: Class-D output driver is powered up. Reserved. Write only reset values. Reserved. Write only reset values. 0: Short circuit is not detected on the class-D driver. Valid only if class-D amplifier is powered up. For short-circuit flag sticky bit, see page 0 / register 44. 1: Short circuit is detected on the class-D driver. Valid only if class-D amp is powered-up. For shortcircuit flag sticky bit, see page 0 / register 44. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Page 1 / Register 33: HP Output Drivers POP Removal Settings D7 READ/ WRITE R/W RESET VALUE 0 D6–D3 R/W 0111 D2–D1 R/W 11 D0 R/W 0 D7 D6–D4 READ/ WRITE R/W R/W RESET VALUE 0 000 D3–D0 R/W 0000 D7–D6 READ/ WRITE R/W RESET VALUE 00 D5 R/W 0 BIT DESCRIPTION 0: If power down sequence is activated by device software power down using page 1 / register 46, bit D7, then power down the DAC simultaneously with the HP and SP amplifiers. 1: If power down sequence is activated by device software power down using page 1 / register 46, bit D7, then power down DAC only after HP and SP amplifiers are completely powered down. This is to optimize power-down POP. 0000: Driver power-on time = 0 μs 0001: Driver power-on time = 15.3 μs 0010: Driver power-on time = 153 μs 0011: Driver power-on time = 1.53 ms 0100: Driver power-on time = 15.3 ms 0101: Driver power-on time = 76.2 ms 0110: Driver power-on time = 153 ms 0111: Driver power-on time = 304 ms 1000: Driver power-on time = 610ms 1001: Driver power-on time = 1.22 s 1010: Driver power-on time = 3.04 s 1011: Driver power-on time = 6.1 s 1100–1111: Reserved. Do not write these sequences to these bits. NOTE: These values are based on typical oscillator frequency of 8.2 MHz. Scale according to the actual oscillator frequency. 00: Driver ramp-up step time = 0 ms 01: Driver ramp-up step time = 0.98 ms 10: Driver ramp-up step time = 1.95 ms 11: Driver ramp-up step time = 3.9 ms NOTE: These values are based on typical oscillator frequency of 8.2 MHz. Scale according to the actual oscillator frequency. 0: Weakly driven output common-mode voltage is generated from resistor divider of the AVDD supply. 1: Reserved. Page 1 / Register 34: Output Driver PGA Ramp-Down Period Control BIT DESCRIPTION Reserved. Write only the reset value to this bit. Speaker Power-Up Wait Time (Duration Based on Using Internal Oscillator) 000: Wait time = 0 ms 001: Wait time = 3.04 ms 010: Wait time = 7.62 ms 011: Wait time = 12.2 ms 100: Wait time = 15.3 ms 101: Wait time = 19.8 ms 110: Wait time = 24.4 ms 111: Wait time = 30.5 ms NOTE: These values are based on typical oscillator frequency of 8.2 MHz. Scale according to the actual oscillator frequency. Reserved. Write only the reset value to these bits. Page 1 / Register 35: DAC Output Mixer Routing BIT D4 D3–D0 0 R/W 0000 DESCRIPTION 00: DAC is not routed anywhere. 01: DAC is routed to the mixer amplifier. 10: DAC is routed directly to the HPOUT driver. 11: Reserved 0: AIN1 input is not routed to the mixer amplifier. 1: AIN1 input is routed to the mixer amplifier. 0: AIN2 input is not routed to the mixer amplifier. 1: AIN2 input is routed to the mixer amplifier. Reserved REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 73 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 1 / Register 36: Analog Vol to HPOUT D7 READ/ WRITE R/W RESET VALUE 0 D6–D0 R/W 111 1111 READ/ WRITE R/W RESET VALUE 0111 1111 D7 READ/ WRITE R/W RESET VALUE 0 D6–D0 R/W 111 1111 READ/ WRITE R/W RESET VALUE 0111 1111 BIT DESCRIPTION 0: Analog volume control is not routed to HPOUT output driver. 1: Analog volume control is routed to HPOUT output driver. Analog volume control gain (non-linear) for the HPOUT output driver, 0 dB to –78 dB. See Table 5-19. Page 1 / Register 37: Reserved BIT D7-D0 DESCRIPTION Reserved Page 1 / Register 38: Analog Vol to Class-D Output Driver BIT DESCRIPTION 0: Analog volume control output is not routed to class-D output driver. 1: Analog volume control output is routed to class-D output driver. Analog volume control output gain (non-linear) for the class-D output driver, 0 dB to –78 dB. See Table 5-19. Page 1 / Register 39: Reserved BIT D7–D0 DESCRIPTION Reserved Page 1 / Register 40: HPOUT Driver D7 D6–D3 READ/ WRITE R/W R/W RESET VALUE 0 0000 D2 R/W 0 D1 R/W 1 D0 R 0 BIT (1) DESCRIPTION Reserved. Write only zero to this bit. 0000: HPOUT driver PGA = 0 dB 0001: HPOUT driver PGA = 1 dB 0010: HPOUT driver PGA = 2 dB ... 1000: HPOUT driver PGA = 8 dB 1001: HPOUT driver PGA = 9 dB 1010–1111: Reserved. Do not write these sequences to these bits. 0: HPOUT driver is muted. 1: HPOUT driver is not muted. 0: HPOUT driver is weakly driven to a common mode during power down. (1) 1: HPOUT driver is high-impedance during power down. 0: Not all programmed gains to HPOUT have been applied yet. 1: All programmed gains to HPOUT have been applied. If D1 is programmed as 0, Page 1 / Register 33 D0 must be set to 0. Page 1 / Register 41: Reserved BIT D7–D0 74 READ/ WRITE R/W RESET VALUE XXXX XXXX DESCRIPTION Reserved. Do not write to this register. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Page 1 / Register 42: Class-D Output Driver D7–D5 D4–D3 READ/ WRITE R/W R/W RESET VALUE 000 00 D2 R/W 0 D1 D0 R/W R 0 0 READ/ WRITE R/W RESET VALUE XXXX XXXX D7–D5 READ/ WRITE R/W RESET VALUE 000 D4–D3 R/W 00 D2 R/W 0 D1–D0 R/W 0 BIT DESCRIPTION Reserved. Write only zeros to these bits. 00: Class-D driver output stage gain = 6 dB 01: Class-D driver output stage gain = 12 dB 10: Class-D driver output stage gain = 18 dB 11: Class-D driver output stage gain = 24 dB 0: Class-D driver is muted. 1: Class-D driver is not muted. Reserved. Write only zero to this bit. 0: Not all programmed gains to class-D driver have been applied yet. 1: All programmed gains to class-D driver have been applied. Page 1 / Register 43: Reserved BIT D7–D0 DESCRIPTION Reserved. Do not wite to this register. Page 1 / Register 44: HP Driver Control BIT (1) DESCRIPTION Debounce time for the headset short-circuit detection MCLK/DIV (Page 3 / (1) register 16) = 1-MHz Internal Oscillator Source Source 000: Debounce time = 0 μs 0 μs 001: Debounce time = 8 μs 7.8 μs 010: Debounce time = 16 μs 15.6 μs 011: Debounce time = 32 μs 31.2 μs 100: Debounce time = 64 μs 62.4 μs 101: Debounce time = 128 μs 124.9 μs 110: Debounce time = 256 μs 250 μs 111: Debounce time = 512 μs 500 μs Note: These values are based on a nominal oscillator frequency of 8.2 MHz. Values will scale to the actual oscillator frequency. 00: Default mode for the DAC 01: DAC performance increased by increasing the current 10: Reserved 11: DAC performance increased further by increasing the current again 0: HPOUT output driver is programmed as headphone driver. 1: HPOUT output driver is programmed as lineout driver. Reserved. Write only zeros to these bits. The clock used for the debounce has a clock period = debounce duration/8. Page 1 / Register 45: Reserved BIT D7–D0 READ/ WRITE R/W RESET VALUE XXXX XXXX DESCRIPTION Reserved. Do not write to these registers. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 75 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 1 / Register 46: MICBIAS D7 READ/ WRITE R/W RESET VALUE 0 D6–D4 D3 R/W R/W 000 0 D2 D1–D0 R/W R/W 0 00 READ/ WRITE R/W RESET VALUE XXXX XXXX D7 READ/ WRITE R/W RESET VALUE 0 D6 R/W 0 D5–D0 R/W 00 0000 READ/ WRITE R/W RESET VALUE XXXX XXXX BIT DESCRIPTION 0: Device software power down is not enabled. 1: Device software power down is enabled. Reserved. Write only zeros to these bits. 0: Programmed MICBIAS is not powered up if headset detection is enabled but headset is not inserted. 1: Programmed MICBIAS is powered up even if headset is not inserted. Reserved. Write only zero to this bit. 00: MICBIAS output is powered down. 01: MICBIAS output is powered to 2 V. 10: MICBIAS output is powered to 2.5 V. 11: MICBIAS output is powered to AVDD. Page 1 / Registers 47–49: Reserved BIT D7–D0 DESCRIPTION Reserved. Write only the reset value to these bits. Table 6-3. Page 1 / Register 50: Input CM Settings BIT DESCRIPTION 0: AIN1 input is floating if it is not used for analog bypass. 1: AIN1 input is connected to CM internally if it is not used for analog bypass. 0: AIN2 input is floating if it is not used for analog bypass. 1: AIN2 input is connected to CM internally if it is not used for analog bypass. Reserved. Write only zeros to these bits. Table 6-4. Page 1 / Registers 51–127: Reserved BIT D7–D0 6.4 DESCRIPTION Reserved. Write only the reset value to these bits. Control Registers, Page 3: MCLK Divider for Programmable Delay Timer Default values shown for this page only become valid 100 μs following a hardware or software reset. Page 3 / Register 0: Page Control Register BIT D7–D0 READ/ WRITE R/W RESET VALUE 0000 0000 DESCRIPTION 0000 0000: 0000 0001: ... 1111 1110: 1111 1111: Page 0 selected Page 1 selected Page 254 selected Page 255 selected The only register used in page 3 is register 16. The remaining page 3 registers are reserved and should not be written to. 76 REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-5. Page 3 / Register 16: MCLK Divider for Programmable Delay Timer D7 READ/ WRITE R/W RESET VALUE 1 D6–D0 R/W 000 0000 BIT (1) DESCRIPTION 0: Internal oscillator is used for programmable delay timer. 1: External MCLK (1) is used for programmable delay timer. MCLK Divider to Generate 1-MHz Clock for the Programmable Delay Timer 000 0000: MCLK divider = 128 000 0001: MCLK divider = 1 000 0010: MCLK divider = 2 ... 111 1110: MCLK divider = 126 111 1111: MCLK divider = 127 External clock is used only to control the delay programmed between the conversions and not used for doing the actual conversion. This feature is provided in case a more accurate delay is desired since the internal oscillator frequency varies from device to device. 6.5 Control Registers, Page 8: DAC Programmable Coefficients RAM Buffer A (1:63) Default values shown for this page only become valid 100 μs following a hardware or software reset. Page 8 / Register 0: Page Control Register BIT D7–D0 READ/ WRITE R/W RESET VALUE 0000 0000 DESCRIPTION 0000 0000: 0000 0001: ... 1111 1110: 1111 1111: Page 0 selected Page 1 selected Page 254 selected Page 255 selected The remaining page-8 registers are either reserved registers or are used for setting coefficients for the various filters in the TLV320DAC3120. Reserved registers should not be written to. The filter coefficient registers are arranged in pairs, with two adjacent 8-bit registers containing the 16-bit coefficient for a single filter. The 16-bit integer contained in the MSB and LSB registers for a coefficient are interpreted as a 2s-complement integer, with possible values ranging from –32,768 to 32,767. When programming any coefficient value for a filter, the MSB register should always be written first, immediately followed by the LSB register. Even if only the MSB or LSB portion of the coefficient changes, both registers should be written in this sequence. Table 6-6 is a list of the page-8 registers, excepting the previously described register 0. Page 8 / Register 1: DAC Coefficient RAM Control D7–D4 D3 READ/ WRITE R/W R RESET VALUE 0000 0 D2 R/W 0 D1 R 0 D0 R/W 0 BIT DESCRIPTION Reserved. Write only the reset value. DAC miniDSP generated flag for toggling MSB of coefficient RAM address (only used in non-adaptive mode) DAC Adaptive Filtering Control 0: Adaptive filtering disabled in DAC miniDSP 1: Adaptive filtering enabled in DAC miniDSP DAC Adaptive Filter Buffer Control Flag 0: In adaptive filter mode, DAC miniDSP accesses DAC coefficient Buffer A and the external control interface accesses DAC coefficient Buffer B 1: In adaptive filter mode, DAC miniDSP accesses DAC coefficient Buffer B and the external control interface accesses DAC coefficient Buffer A DAC Adaptive Filter Buffer Switch Control 0: DAC coefficient buffers are not switched at the next frame boundary. 1: DAC coefficient buffers are switched at the next frame boundary, if adaptive filtering mode is enabled. This bit self-clears on switching. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 77 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-6. Page-8 Registers 78 REGISTER NUMBER RESET VALUE 2 0111 1111 Coefficient N0(15:8) for left DAC-programmable biquad A or Coefficient C1(15:8) of DAC miniDSP (DAC Buffer A) 3 1111 1111 Coefficient N0(7:0) for left DAC-programmable biquad A or Coefficient C1(7:0) of DAC miniDSP (DAC Buffer A) 4 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad A or Coefficient C2(15:8) of DAC miniDSP (DAC Buffer A) 5 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad A or Coefficient C2(7:0) of DAC miniDSP (DAC Buffer A) 6 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad A or Coefficient C3(15:8) of DAC miniDSP (DAC Buffer A) 7 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad A or Coefficient C3(7:0) of DAC miniDSP (DAC Buffer A) 8 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad A or Coefficient C4(15:8) of DAC miniDSP (DAC Buffer A) 9 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad A or Coefficient C4(7:0) of DAC miniDSP (DAC Buffer A) 10 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad A or Coefficient C5(15:8) of DAC miniDSP (DAC Buffer A) 11 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad A or Coefficient C5(7:0) of DAC miniDSP (DAC Buffer A) 12 0111 1111 Coefficient N0(15:8) for left DAC-programmable biquad B or Coefficient C6(15:8) of DAC miniDSP (DAC Buffer A) 13 1111 1111 Coefficient N0(7:0) for left DAC-programmable biquad B or Coefficient C6(7:0) of DAC miniDSP (DAC Buffer A) 14 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad B or Coefficient C7(15:8) of DAC miniDSP (DAC Buffer A) 15 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad B or Coefficient C7(7:0) of DAC miniDSP (DAC Buffer A) 16 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad B or Coefficient C8(15:8) of DAC miniDSP (DAC Buffer A) 17 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad B or Coefficient C8(7:0) of DAC miniDSP (DAC Buffer A) 18 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad B or Coefficient C9(15:8) of DAC miniDSP (DAC Buffer A) 19 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad B or Coefficient C9(7:0) of DAC miniDSP (DAC Buffer A) 20 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad B or Coefficient C10(15:8) of DAC miniDSP (DAC Buffer A) 21 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad B or Coefficient C10(7:0) of DAC miniDSP (DAC Buffer A) 22 0111 1111 Coefficient N0(15:8) for left DAC-programmable biquad C or Coefficient C11(15:8) of DAC miniDSP (DAC Buffer A) 23 1111 1111 Coefficient N0(7:0) for left DAC-programmable biquad C or Coefficient C11(7:0) of DAC miniDSP (DAC Buffer A) 24 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad C or Coefficient C12(15:8) of DAC miniDSP (DAC Buffer A) 25 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad C or Coefficient C12(7:0) of DAC miniDSP (DAC Buffer A) 26 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad C or Coefficient C13(15:8) of DAC miniDSP (DAC Buffer A) 27 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad C or Coefficient C13(7:0) of DAC miniDSP (DAC Buffer A) 28 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad C or Coefficient C14(15:8) of DAC miniDSP (DAC Buffer A) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-6. Page-8 Registers (continued) REGISTER NUMBER RESET VALUE 29 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad C or Coefficient C14(7:0) of DAC miniDSP (DAC Buffer A) 30 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad C or Coefficient C15(15:8) of DAC miniDSP (DAC Buffer A) 31 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad C or Coefficient C15(7:0) of DAC miniDSP (DAC Buffer A) 32 0111 1111 Coefficient N0(15:8) for left DAC-programmable biquad D or Coefficient C16(15:8) of DAC miniDSP (DAC Buffer A) 33 1111 1111 Coefficient N0(7:0) for left DAC-programmable biquad D or Coefficient C16(7:0) of DAC miniDSP (DAC Buffer A) 34 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad D or Coefficient C17(15:8) of DAC miniDSP (DAC Buffer A) 35 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad D or Coefficient C17(7:0) of DAC miniDSP (DAC Buffer A) 36 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad D or Coefficient C18(15:8) of DAC miniDSP (DAC Buffer A) 37 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad D or Coefficient C18(7:0) of DAC miniDSP (DAC Buffer A) 38 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad D or Coefficient C19(15:8) of DAC miniDSP (DAC Buffer A) 39 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad D or Coefficient C19(7:0) of DAC miniDSP (DAC Buffer A) 40 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad D or Coefficient C20(15:8) of DAC miniDSP (DAC Buffer A) 41 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad D or Coefficient C20(7:0) of DAC miniDSP (DAC Buffer A) 42 0111 1111 Coefficient N0(15:8) for left DAC-programmable biquad E or Coefficient C21(15:8) of DAC miniDSP (DAC Buffer A) 43 1111 1111 Coefficient N0(7:0) for left DAC-programmable biquad E or Coefficient C21(7:0) of DAC miniDSP (DAC Buffer A) 44 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad E or Coefficient C22(15:8) of DAC miniDSP (DAC Buffer A) 45 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad E or Coefficient C22(7:0) of DAC miniDSP (DAC Buffer A) 46 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad E or Coefficient C23(15:8) of DAC miniDSP (DAC Buffer A) 47 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad E or Coefficient C23(7:0) of DAC miniDSP (DAC Buffer A) 48 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad E or Coefficient C24(15:8) of DAC miniDSP (DAC Buffer A) 49 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad E or Coefficient C24(7:0) of DAC miniDSP (DAC Buffer A) 50 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad E or Coefficient C25(15:8) of DAC miniDSP (DAC Buffer A) 51 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad E or Coefficient C25(7:0) of DAC miniDSP (DAC Buffer A) 52 0111 1111 Coefficient N0(15:8) for left DAC-programmable biquad F or Coefficient C26(15:8) of DAC miniDSP (DAC Buffer A) 53 1111 1111 Coefficient N0(7:0) for left DAC-programmable biquad F or Coefficient C26(7:0) of DAC miniDSP (DAC Buffer A) 54 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad F or Coefficient C27(15:8) of DAC miniDSP (DAC Buffer A) 55 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad F or Coefficient C27(7:0) of DAC miniDSP (DAC Buffer A) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 79 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-6. Page-8 Registers (continued) 80 REGISTER NUMBER RESET VALUE 56 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad F or Coefficient C28(15:8) of DAC miniDSP (DAC Buffer A) 57 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad F or Coefficient C28(7:0) of DAC miniDSP (DAC Buffer A) 58 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad F or Coefficient C29(15:8) of DAC miniDSP (DAC Buffer A) 59 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad F or Coefficient C29(7:0) of DAC miniDSP (DAC Buffer A) 60 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad F or Coefficient C30(15:8) of DAC miniDSP (DAC Buffer A) 61 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad F or Coefficient C30(7:0) of DAC miniDSP (DAC Buffer A) 62 0000 0000 Coefficient C31(15:8) of DAC miniDSP (DAC Buffer A) 63 0000 0000 Coefficient C31(7:0) of DAC miniDSP (DAC Buffer A) 64 0000 0000 Coefficient C32(15:8) of DAC miniDSP (DAC Buffer A)—also used for the 3D PGA for PRB_P23, PRB_P24 and PRB_P25 65 0000 0000 Coefficient C32(7:0) of DAC miniDSP (DAC Buffer A)—also used for the 3D PGA for PRB_P23, PRB_P24 and PRB_P25 66 0111 1111 Reserved. 67 1111 1111 Reserved. 68 0000 0000 Reserved. 69 0000 0000 Reserved. 70 0000 0000 Reserved. 71 0000 0000 Reserved. 72 0000 0000 Reserved. 73 0000 0000 Reserved. 74 0000 0000 Reserved. 75 0000 0000 Reserved. 76 0111 1111 Reserved. 77 1111 1111 Reserved. 78 0000 0000 Reserved. 79 0000 0000 Reserved. 80 0000 0000 Reserved. 81 0000 0000 Reserved. 82 0000 0000 Reserved. 83 0000 0000 Reserved. 84 0000 0000 Reserved. 85 0000 0000 Reserved. 86 0111 1111 Reserved. 87 1111 1111 Reserved. 88 0000 0000 Reserved. 89 0000 0000 Reserved. 90 0000 0000 Reserved. 91 0000 0000 Reserved. 92 0000 0000 Reserved. 93 0000 0000 Reserved. 94 0000 0000 Reserved. 95 0000 0000 Reserved. 96 0111 1111 Reserved. REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-6. Page-8 Registers (continued) REGISTER NUMBER RESET VALUE 97 1111 1111 Reserved. 98 0000 0000 Reserved. 99 0000 0000 Reserved. 100 0000 0000 Reserved. 101 0000 0000 Reserved. 102 0000 0000 Reserved. 103 0000 0000 Reserved. 104 0000 0000 Reserved. 105 0000 0000 Reserved. 106 0111 1111 Reserved. 107 1111 1111 Reserved. 108 0000 0000 Reserved. 109 0000 0000 Reserved. 110 0000 0000 Reserved. 111 0000 0000 Reserved. 112 0000 0000 Reserved. 113 0000 0000 Reserved. 114 0000 0000 Reserved. 115 0000 0000 Reserved. 116 0111 1111 Reserved. 117 1111 1111 Reserved. 118 0000 0000 Reserved. 119 0000 0000 Reserved. 120 0000 0000 Reserved. 121 0000 0000 Reserved. 122 0000 0000 Reserved. 123 0000 0000 Reserved. 124 0000 0000 Reserved. 125 0000 0000 Reserved. 126 0000 0000 Reserved. 127 0000 0000 Reserved. REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 81 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 6.6 www.ti.com Control Registers, Page 9: DAC Programmable Coefficients RAM Buffer A (65:127) Default values shown for this page only become valid 100 μs following a hardware or software reset. Page 9 / Register 0: Page Control Register READ/ WRITE R/W BIT D7–D0 RESET VALUE 0000 0000 DESCRIPTION 0000 0000: 0000 0001: ... 1111 1110: 1111 1111: Page 0 selected Page 1 selected Page 254 selected Page 255 selected The remaining page-9 registers are either reserved registers or are used for setting coefficients for the various filters in the TLV320DAC3120. Reserved registers should not be written to. The filter-coefficient registers are arranged in pairs, with two adjacent 8-bit registers containing the 16-bit coefficient for a single filter. The 16-bit integer contained in the MSB and LSB registers for a coefficient are interpreted as a 2s-complement integer, with possible values ranging from –32,768 to 32,767. When programming any coefficient value for a filter, the MSB register should always be written first, immediately followed by the LSB register. Even if only the MSB or LSB portion of the coefficient changes, both registers should be written in this sequence. Table 6-7 is a list of the page-9 registers, excepting the previously described register 0. Table 6-7. Page-9 Registers 82 REGISTER NUMBER RESET VALUE 1 XXXX XXXX 2 0111 1111 Coefficient N0(15:8) for left DAC-programmable first-order IIR or Coefficient C65(15:8) of DAC miniDSP (DAC Buffer A) 3 1111 1111 Coefficient N0(7:0) for left DAC-programmable first-order IIR or Coefficient C65(7:0) of DAC miniDSP (DAC Buffer A) 4 0000 0000 Coefficient N1(15:8) for left DAC-programmable first-order IIR or Coefficient C66(15:8) of DAC miniDSP (DAC Buffer A) 5 0000 0000 Coefficient N1(7:0) for left DAC-programmable first-order IIR or Coefficient C66(7:0) of DAC miniDSP (DAC Buffer A) 6 0000 0000 Coefficient D1(15:8) for left DAC-programmable first-order IIR or Coefficient C67(15:8) of DAC miniDSP (DAC Buffer A) 7 0000 0000 Coefficient D1(7:0) for left DAC-programmable first-order IIR or Coefficient C67(7:0) of DAC miniDSP (DAC Buffer A) 8 0111 1111 Reserved. 9 1111 1111 Reserved. 10 0000 0000 Reserved. 11 0000 0000 Reserved. 12 0000 0000 Reserved. 13 0000 0000 Reserved. 14 0111 1111 Coefficient N0(15:8) for DRC first-order high-pass filter or Coefficient C71(15:8) of DAC miniDSP (DAC Buffer A) 15 1111 0111 Coefficient N0(7:0) for DRC first-order high-pass filter or Coefficient C71(7:0) of DAC miniDSP (DAC Buffer A) 16 1000 0000 Coefficient N1(15:8) for DRC first-order high-pass filter or Coefficient C72(15:8) of DAC miniDSP (DAC Buffer A) 17 0000 1001 Coefficient N1(7:0) for DRC first-order high-pass filter or Coefficient C72(7:0) of DAC miniDSP (DAC Buffer A) 18 0111 1111 Coefficient D1(15:8) for DRC first-order high-pass filter or Coefficient C73(15:8) of DAC miniDSP (DAC Buffer A) REGISTER NAME Reserved. Do not write to this register. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-7. Page-9 Registers (continued) REGISTER NUMBER RESET VALUE REGISTER NAME 19 1110 1111 Coefficient D1(7:0) for DRC first-order high-pass filter or Coefficient C73(7:0) of DAC miniDSP (DAC Buffer A) 20 0000 0000 Coefficient N0(15:8) for DRC first-order low-pass filter or Coefficient C74(15:8) of DAC miniDSP (DAC Buffer A) 21 0001 0001 Coefficient N0(7:0) for DRC first-order low-pass filter or Coefficient C74(7:0) of DAC miniDSP (DAC Buffer A) 22 0000 0000 Coefficient N1(15:8) for DRC first-order low-pass filter or Coefficient C75(15:8) of DAC miniDSP (DAC Buffer A) 23 0001 0001 Coefficient N1(7:0) for DRC first-order low-pass filter or Coefficient C75(7:0) of DAC miniDSP (DAC Buffer A) 24 0111 1111 Coefficient D1(15:8) for DRC first-order low-pass filter or Coefficient C76(15:8) of DAC miniDSP (DAC Buffer A) 25 1101 1110 Coefficient D1(7:0) for DRC first-order low-pass filter or Coefficient C76(7:0) of DAC miniDSP (DAC Buffer A) 26 0000 0000 Coefficient C77(15:8) of DAC miniDSP (DAC Buffer A) 27 0000 0000 Coefficient C77(7:0) of DAC miniDSP (DAC Buffer A) 28 0000 0000 Coefficient C78(15:8) of DAC miniDSP (DAC Buffer A) 29 0000 0000 Coefficient C78(7:0) of DAC miniDSP (DAC Buffer A) 30 0000 0000 Coefficient C79(15:8) of DAC miniDSP (DAC Buffer A) 31 0000 0000 Coefficient C79(7:0) of DAC miniDSP (DAC Buffer A) 32 0000 0000 Coefficient C80(15:8) of DAC miniDSP (DAC Buffer A) 33 0000 0000 Coefficient C80(7:0) of DAC miniDSP (DAC Buffer A) 34 0000 0000 Coefficient C81(15:8) of DAC miniDSP (DAC Buffer A) 35 0000 0000 Coefficient C81(7:0) of DAC miniDSP (DAC Buffer A) 36 0000 0000 Coefficient C82(15:8) of DAC miniDSP (DAC Buffer A) 37 0000 0000 Coefficient C82(7:0) of DAC miniDSP (DAC Buffer A) 38 0000 0000 Coefficient C83(15:8) of DAC miniDSP (DAC Buffer A) 39 0000 0000 Coefficient C83(7:0) of DAC miniDSP (DAC Buffer A) 40 0000 0000 Coefficient C84(15:8) of DAC miniDSP (DAC Buffer A) 41 0000 0000 Coefficient C84(7:0) of DAC miniDSP (DAC Buffer A) 42 0000 0000 Coefficient C85(15:8) of DAC miniDSP (DAC Buffer A) 43 0000 0000 Coefficient C85(7:0) of DAC miniDSP (DAC Buffer A) 44 0000 0000 Coefficient C86(15:8) of DAC miniDSP (DAC Buffer A) 45 0000 0000 Coefficient C86(7:0) of DAC miniDSP (DAC Buffer A) 46 0000 0000 Coefficient C87(15:8) of DAC miniDSP (DAC Buffer A) 47 0000 0000 Coefficient C87(7:0) of DAC miniDSP (DAC Buffer A) 48 0000 0000 Coefficient C88(15:8) of DAC miniDSP (DAC Buffer A) 49 0000 0000 Coefficient C88(7:0) of DAC miniDSP (DAC Buffer A) 50 0000 0000 Coefficient C89(15:8) of DAC miniDSP (DAC Buffer A) 51 0000 0000 Coefficient C89(7:0) of DAC miniDSP (DAC Buffer A) 52 0000 0000 Coefficient C90(15:8) of DAC miniDSP (DAC Buffer A) 53 0000 0000 Coefficient C90(7:0) of DAC miniDSP (DAC Buffer A) 54 0000 0000 Coefficient C91(15:8) of DAC miniDSP (DAC Buffer A) 55 0000 0000 Coefficient C91(7:0) of DAC miniDSP (DAC Buffer A) 56 0000 0000 Coefficient C92(15:8) of DAC miniDSP (DAC Buffer A) 57 0000 0000 Coefficient C92(7:0) of DAC miniDSP (DAC Buffer A) 58 0000 0000 Coefficient C93(15:8) of DAC miniDSP (DAC Buffer A) 59 0000 0000 Coefficient C93(7:0) of DAC miniDSP (DAC Buffer A) 60 0000 0000 Coefficient C94(15:8) of DAC miniDSP (DAC Buffer A) REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 83 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-7. Page-9 Registers (continued) 84 REGISTER NUMBER RESET VALUE 61 0000 0000 Coefficient C94(7:0) of DAC miniDSP (DAC Buffer A) 62 0000 0000 Coefficient C95(15:8) of DAC miniDSP (DAC Buffer A) 63 0000 0000 Coefficient C95(7:0) of DAC miniDSP (DAC Buffer A) 64 0000 0000 Coefficient C96(15:8) of DAC miniDSP (DAC Buffer A) 65 0000 0000 Coefficient C96(7:0) of DAC miniDSP (DAC Buffer A) 66 0000 0000 Coefficient C97(15:8) of DAC miniDSP (DAC Buffer A) 67 0000 0000 Coefficient C97(7:0) of DAC miniDSP (DAC Buffer A) 68 0000 0000 Coefficient C98(15:8) of DAC miniDSP (DAC Buffer A) 69 0000 0000 Coefficient C98(7:0) of DAC miniDSP (DAC Buffer A) 70 0000 0000 Coefficient C99(15:8) of DAC miniDSP (DAC Buffer A) 71 0000 0000 Coefficient C99(7:0) of DAC miniDSP (DAC Buffer A) 72 0000 0000 Coefficient C100(15:8) of DAC miniDSP (DAC Buffer A) 73 0000 0000 Coefficient C100(7:0) of DAC miniDSP (DAC Buffer A) 74 0000 0000 Coefficient C101(15:8) of DAC miniDSP (DAC Buffer A) 75 0000 0000 Coefficient C101(7:0) of DAC miniDSP (DAC Buffer A) 76 0000 0000 Coefficient C102(15:8) of DAC miniDSP (DAC Buffer A) 77 0000 0000 Coefficient C102(7:0) of DAC miniDSP (DAC Buffer A) 78 0000 0000 Coefficient C103(15:8) of DAC miniDSP (DAC Buffer A) 79 0000 0000 Coefficient C103(7:0) of DAC miniDSP (DAC Buffer A) 80 0000 0000 Coefficient C104(15:8) of DAC miniDSP (DAC Buffer A) 81 0000 0000 Coefficient C104(7:0) of DAC miniDSP (DAC Buffer A) 82 0000 0000 Coefficient C105(15:8) of DAC miniDSP (DAC Buffer A) 83 0000 0000 Coefficient C105(7:0) of DAC miniDSP (DAC Buffer A) 84 0000 0000 Coefficient C106(15:8) of DAC miniDSP (DAC Buffer A) 85 0000 0000 Coefficient C106(7:0) of DAC miniDSP (DAC Buffer A) 86 0000 0000 Coefficient C107(15:8) of DAC miniDSP (DAC Buffer A) 87 0000 0000 Coefficient C107(15:8) of DAC miniDSP (DAC Buffer A) 88 0000 0000 Coefficient C108(7:0) of DAC miniDSP (DAC Buffer A) 89 0000 0000 Coefficient C108(7:0) of DAC miniDSP (DAC Buffer A) 90 0000 0000 Coefficient C109(15:8) of DAC miniDSP (DAC Buffer A) 91 0000 0000 Coefficient C109(7:0) of DAC miniDSP (DAC Buffer A) 92 0000 0000 Coefficient C110(15:8) of DAC miniDSP (DAC Buffer A) 93 0000 0000 Coefficient C110(7:0) of DAC miniDSP (DAC Buffer A) 94 0000 0000 Coefficient C111(15:8) of DAC miniDSP (DAC Buffer A) 95 0000 0000 Coefficient C111(7:0) of DAC miniDSP (DAC Buffer A) 96 0000 0000 Coefficient C112(15:8) of DAC miniDSP (DAC Buffer A) 97 0000 0000 Coefficient C112(7:0) of DAC miniDSP (DAC Buffer A) 98 0000 0000 Coefficient C113(15:8) of DAC miniDSP (DAC Buffer A) 99 0000 0000 Coefficient C113(7:0) of DAC miniDSP (DAC Buffer A) 100 0000 0000 Coefficient C114(15:8) of DAC miniDSP (DAC Buffer A) 101 0000 0000 Coefficient C114(7:0) of DAC miniDSP (DAC Buffer A) 102 0000 0000 Coefficient C11515:8) of DAC miniDSP (DAC Buffer A) 103 0000 0000 Coefficient C115(7:0) of DAC miniDSP (DAC Buffer A) 104 0000 0000 Coefficient C116(15:8) of DAC miniDSP (DAC Buffer A) 105 0000 0000 Coefficient C116(7:0) of DAC miniDSP (DAC Buffer A) 106 0000 0000 Coefficient C117(15:8) of DAC miniDSP (DAC Buffer A) 107 0000 0000 Coefficient C117(7:0) of DAC miniDSP (DAC Buffer A) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-7. Page-9 Registers (continued) REGISTER NUMBER RESET VALUE 108 0000 0000 Coefficient C118(15:8) of DAC miniDSP (DAC Buffer A) 109 0000 0000 Coefficient C118(7:0) of DAC miniDSP (DAC Buffer A) 110 0000 0000 Coefficient C119(15:8) of DAC miniDSP (DAC Buffer A) 111 0000 0000 Coefficient C119(7:0) of DAC miniDSP (DAC Buffer A) 112 0000 0000 Coefficient C120(15:8) of DAC miniDSP (DAC Buffer A) 113 0000 0000 Coefficient C120(7:0) of DAC miniDSP (DAC Buffer A) 114 0000 0000 Coefficient C121(15:8) of DAC miniDSP (DAC Buffer A) 115 0000 0000 Coefficient C121(7:0) of DAC miniDSP (DAC Buffer A) 116 0000 0000 Coefficient C122(15:8) of DAC miniDSP (DAC Buffer A) 117 0000 0000 Coefficient C122(7:0) of DAC miniDSP (DAC Buffer A) 118 0000 0000 Coefficient C123(15:8) of DAC miniDSP (DAC Buffer A) 119 0000 0000 Coefficient C123(7:0) of DAC miniDSP (DAC Buffer A) 120 0000 0000 Coefficient C124(15:8) of DAC miniDSP (DAC Buffer A) 121 0000 0000 Coefficient C124(7:0) of DAC miniDSP (DAC Buffer A) 122 0000 0000 Coefficient C125(15:8) of DAC miniDSP (DAC Buffer A) 123 0000 0000 Coefficient C125(7:0) of DAC miniDSP (DAC Buffer A) 124 0000 0000 Coefficient C126(15:8) of DAC miniDSP (DAC Buffer A) 125 0000 0000 Coefficient C126(7:0) of DAC miniDSP (DAC Buffer A) 126 0000 0000 Coefficient C127(15:8) of DAC miniDSP (DAC Buffer A) 127 0000 0000 Coefficient C127(7:0) of DAC miniDSP (DAC Buffer A) 6.7 REGISTER NAME Control Registers, Page 10: DAC Programmable Coefficients RAM Buffer A (129:191) Table 6-8. Page-10 Registers REGISTER NUMBER RESET VALUE 1 XXXX XXXX 2 0000 0000 Coefficient C129(15:8) of DAC miniDSP (DAC Buffer A) 3 0000 0000 Coefficient C129(7:0) of DAC miniDSP (DAC Buffer A) 4 0000 0000 Coefficient C130(15:8) of DAC miniDSP (DAC Buffer A) 5 0000 0000 Coefficient C130(7:0) of DAC miniDSP (DAC Buffer A) 6 0000 0000 Coefficient C131(15:8) of DAC miniDSP (DAC Buffer A) 7 0000 0000 Coefficient C131(7:0) of DAC miniDSP (DAC Buffer A) 8 0000 0000 Coefficient C132(15:8) of DAC miniDSP (DAC Buffer A) REGISTER NAME Reserved. Do not write to this register. 9 0000 0000 Coefficient C132(7:0) of DAC miniDSP (DAC Buffer A) 10 0000 0000 Coefficient C133(15:8) of DAC miniDSP (DAC Buffer A) 11 0000 0000 Coefficient C133(7:0) of DAC miniDSP (DAC Buffer A) 12 0000 0000 Coefficient C134(15:8) of DAC miniDSP (DAC Buffer A) 13 0000 0000 Coefficient C134(7:0) of DAC miniDSP (DAC Buffer A) 14 0000 0000 Coefficient C135(15:8) of DAC miniDSP (DAC Buffer A) 15 0000 0000 Coefficient C135(7:0) of DAC miniDSP (DAC Buffer A) 16 0000 0000 Coefficient C136(15:8) of DAC miniDSP (DAC Buffer A) 17 0000 0000 Coefficient C136(7:0) of DAC miniDSP (DAC Buffer A) 18 0000 0000 Coefficient C137(15:8) of DAC miniDSP (DAC Buffer A) 19 0000 0000 Coefficient C137(7:0) of DAC miniDSP (DAC Buffer A) REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 85 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-8. Page-10 Registers (continued) 86 REGISTER NUMBER RESET VALUE 20 0000 0000 Coefficient C138(15:8) of DAC miniDSP (DAC Buffer A) 21 0000 0000 Coefficient C138(7:0) of DAC miniDSP (DAC Buffer A) 22 0000 0000 Coefficient C139(15:8) of DAC miniDSP (DAC Buffer A) 23 0000 0000 Coefficient C139(7:0) of DAC miniDSP (DAC Buffer A) 24 0000 0000 Coefficient C140(15:8) of DAC miniDSP (DAC Buffer A) 25 0000 0000 Coefficient C140(7:0) of DAC miniDSP (DAC Buffer A) 26 0000 0000 Coefficient C141(15:8) of DAC miniDSP (DAC Buffer A) 27 0000 0000 Coefficient C141(7:0) of DAC miniDSP (DAC Buffer A) 28 0000 0000 Coefficient C142(15:8) of DAC miniDSP (DAC Buffer A) 29 0000 0000 Coefficient C142(7:0) of DAC miniDSP (DAC Buffer A) 30 0000 0000 Coefficient C143(15:8) of DAC miniDSP (DAC Buffer A) 31 0000 0000 Coefficient C143(7:0) of DAC miniDSP (DAC Buffer A) 32 0000 0000 Coefficient C144(15:8) of DAC miniDSP (DAC Buffer A) 33 0000 0000 Coefficient C144(7:0) of DAC miniDSP (DAC Buffer A) 34 0000 0000 Coefficient C145(15:8) of DAC miniDSP (DAC Buffer A) 35 0000 0000 Coefficient C145(7:0) of DAC miniDSP (DAC Buffer A) 36 0000 0000 Coefficient C146(15:8) of DAC miniDSP (DAC Buffer A) 37 0000 0000 Coefficient C146(7:0) of DAC miniDSP (DAC Buffer A) 38 0000 0000 Coefficient C147(15:8) of DAC miniDSP (DAC Buffer A) 39 0000 0000 Coefficient C147(7:0) of DAC miniDSP (DAC Buffer A) 40 0000 0000 Coefficient C148(15:8) of DAC miniDSP (DAC Buffer A) 41 0000 0000 Coefficient C148(7:0) of DAC miniDSP (DAC Buffer A) 42 0000 0000 Coefficient C149(15:8) of DAC miniDSP (DAC Buffer A) 43 0000 0000 Coefficient C149(7:0) of DAC miniDSP (DAC Buffer A) 44 0000 0000 Coefficient C150(15:8) of DAC miniDSP (DAC Buffer A) 45 0000 0000 Coefficient C150(7:0) of DAC miniDSP (DAC Buffer A) 46 0000 0000 Coefficient C151(15:8) of DAC miniDSP (DAC Buffer A) 47 0000 0000 Coefficient C151(7:0) of DAC miniDSP (DAC Buffer A) 48 0000 0000 Coefficient C152(15:8) of DAC miniDSP (DAC Buffer A) 49 0000 0000 Coefficient C152(7:0) of DAC miniDSP (DAC Buffer A) 50 0000 0000 Coefficient C153(15:8) of DAC miniDSP (DAC Buffer A) 51 0000 0000 Coefficient C153(7:0) of DAC miniDSP (DAC Buffer A) 52 0000 0000 Coefficient C154(15:8) of DAC miniDSP (DAC Buffer A) 53 0000 0000 Coefficient C154(7:0) of DAC miniDSP (DAC Buffer A) 54 0000 0000 Coefficient C155(15:8) of DAC miniDSP (DAC Buffer A) 55 0000 0000 Coefficient C155(7:0) of DAC miniDSP (DAC Buffer A) 56 0000 0000 Coefficient C156(15:8) of DAC miniDSP (DAC Buffer A) 57 0000 0000 Coefficient C156(7:0) of DAC miniDSP (DAC Buffer A) 58 0000 0000 Coefficient C157(15:8) of DAC miniDSP (DAC Buffer A) 59 0000 0000 Coefficient C157(7:0) of DAC miniDSP (DAC Buffer A) 60 0000 0000 Coefficient C158(15:8) of DAC miniDSP (DAC Buffer A) 61 0000 0000 Coefficient C158(7:0) of DAC miniDSP (DAC Buffer A) 62 0000 0000 Coefficient C159(15:8) of DAC miniDSP (DAC Buffer A) 63 0000 0000 Coefficient C159(7:0) of DAC miniDSP (DAC Buffer A) 64 0000 0000 Coefficient C160(15:8) of DAC miniDSP (DAC Buffer A) 65 0000 0000 Coefficient C160(7:0) of DAC miniDSP (DAC Buffer A) 66 0000 0000 Coefficient C161(15:8) of DAC miniDSP (DAC Buffer A) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-8. Page-10 Registers (continued) REGISTER NUMBER RESET VALUE 67 0000 0000 Coefficient C161(7:0) of DAC miniDSP (DAC Buffer A) 68 0000 0000 Coefficient C162(15:8) of DAC miniDSP (DAC Buffer A) 69 0000 0000 Coefficient C162(7:0) of DAC miniDSP (DAC Buffer A) 70 0000 0000 Coefficient C163(15:8) of DAC miniDSP (DAC Buffer A) 71 0000 0000 Coefficient C163(7:0) of DAC miniDSP (DAC Buffer A) 72 0000 0000 Coefficient C164(15:8) of DAC miniDSP (DAC Buffer A) 73 0000 0000 Coefficient C164(7:0) of DAC miniDSP (DAC Buffer A) 74 0000 0000 Coefficient C165(15:8) of DAC miniDSP (DAC Buffer A) 75 0000 0000 Coefficient C165(7:0) of DAC miniDSP (DAC Buffer A) 76 0000 0000 Coefficient C166(15:8) of DAC miniDSP (DAC Buffer A) 77 0000 0000 Coefficient C166(7:0) of DAC miniDSP (DAC Buffer A) 78 0000 0000 Coefficient C167(15:8) of DAC miniDSP (DAC Buffer A) 79 0000 0000 Coefficient C167(7:0) of DAC miniDSP (DAC Buffer A) 80 0000 0000 Coefficient C168(15:8) of DAC miniDSP (DAC Buffer A) 81 0000 0000 Coefficient C168(7:0) of DAC miniDSP (DAC Buffer A) 82 0000 0000 Coefficient C169(15:8) of DAC miniDSP (DAC Buffer A) 83 0000 0000 Coefficient C169(7:0) of DAC miniDSP (DAC Buffer A) 84 0000 0000 Coefficient C170(15:8) of DAC miniDSP (DAC Buffer A) 85 0000 0000 Coefficient C170(7:0) of DAC miniDSP (DAC Buffer A) 86 0000 0000 Coefficient C171(15:8) of DAC miniDSP (DAC Buffer A) 87 0000 0000 Coefficient C171(7:0) of DAC miniDSP (DAC Buffer A) 88 0000 0000 Coefficient C172(15:8) of DAC miniDSP (DAC Buffer A) 89 0000 0000 Coefficient C172(7:0) of DAC miniDSP (DAC Buffer A) 90 0000 0000 Coefficient C173(15:8) of DAC miniDSP (DAC Buffer A) 91 0000 0000 Coefficient C173(7:0) of DAC miniDSP (DAC Buffer A) 92 0000 0000 Coefficient C174(15:8) of DAC miniDSP (DAC Buffer A) 93 0000 0000 Coefficient C174(7:0) of DAC miniDSP (DAC Buffer A) 94 0000 0000 Coefficient C175(15:8) of DAC miniDSP (DAC Buffer A) 95 0000 0000 Coefficient C175(7:0) of DAC miniDSP (DAC Buffer A) 96 0000 0000 Coefficient C176(15:8) of DAC miniDSP (DAC Buffer A) 97 0000 0000 Coefficient C176(7:0) of DAC miniDSP (DAC Buffer A) 98 0000 0000 Coefficient C177(15:8) of DAC miniDSP (DAC Buffer A) 99 0000 0000 Coefficient C177(7:0) of DAC miniDSP (DAC Buffer A) 100 0000 0000 Coefficient C178(15:8) of DAC miniDSP (DAC Buffer A) 101 0000 0000 Coefficient C178(7:0) of DAC miniDSP (DAC Buffer A) 102 0000 0000 Coefficient C179(15:8) of DAC miniDSP (DAC Buffer A) 103 0000 0000 Coefficient C179(7:0) of DAC miniDSP (DAC Buffer A) 104 0000 0000 Coefficient C180(15:8) of DAC miniDSP (DAC Buffer A) 105 0000 0000 Coefficient C180(7:0) of DAC miniDSP (DAC Buffer A) 106 0000 0000 Coefficient C181(15:8) of DAC miniDSP (DAC Buffer A) 107 0000 0000 Coefficient C181(7:0) of DAC miniDSP (DAC Buffer A) 108 0000 0000 Coefficient C182(15:8) of DAC miniDSP (DAC Buffer A) 109 0000 0000 Coefficient C182(7:0) of DAC miniDSP (DAC Buffer A) 110 0000 0000 Coefficient C183(15:8) of DAC miniDSP (DAC Buffer A) 111 0000 0000 Coefficient C183(7:0) of DAC miniDSP (DAC Buffer A) 112 0000 0000 Coefficient C184(15:8) of DAC miniDSP (DAC Buffer A) 113 0000 0000 Coefficient C184(7:0) of DAC miniDSP (DAC Buffer A) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 87 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-8. Page-10 Registers (continued) REGISTER NUMBER RESET VALUE 114 0000 0000 Coefficient C185(15:8) of DAC miniDSP (DAC Buffer A) 115 0000 0000 Coefficient C185(7:0) of DAC miniDSP (DAC Buffer A) 116 0000 0000 Coefficient C186(15:8) of DAC miniDSP (DAC Buffer A) 117 0000 0000 Coefficient C186(7:0) of DAC miniDSP (DAC Buffer A) 118 0000 0000 Coefficient C187(15:8) of DAC miniDSP (DAC Buffer A) 119 0000 0000 Coefficient C187(7:0) of DAC miniDSP (DAC Buffer A) 120 0000 0000 Coefficient C188(15:8) of DAC miniDSP (DAC Buffer A) 121 0000 0000 Coefficient C188(7:0) of DAC miniDSP (DAC Buffer A) 122 0000 0000 Coefficient C189(15:8) of DAC miniDSP (DAC Buffer A) 123 0000 0000 Coefficient C189(7:0) of DAC miniDSP (DAC Buffer A) 124 0000 0000 Coefficient C190(15:8) of DAC miniDSP (DAC Buffer A) 125 0000 0000 Coefficient C190(7:0) of DAC miniDSP (DAC Buffer A) 126 0000 0000 Coefficient C191(15:8) of DAC miniDSP (DAC Buffer A) 127 0000 0000 Coefficient C191(7:0) of DAC miniDSP (DAC Buffer A) 6.8 REGISTER NAME Control Registers, Page 11: DAC Programmable Coefficients RAM Buffer A (193:255) Table 6-9. Page-11 Registers 88 REGISTER NUMBER RESET VALUE 1 XXXX XXXX 2 0000 0000 Coefficient C193(15:8) of DAC miniDSP (DAC Buffer A) 3 0000 0000 Coefficient C193(7:0) of DAC miniDSP (DAC Buffer A) 4 0000 0000 Coefficient C194(15:8) of DAC miniDSP (DAC Buffer A) 5 0000 0000 Coefficient C194(7:0) of DAC miniDSP (DAC Buffer A) 6 0000 0000 Coefficient C195(15:8) of DAC miniDSP (DAC Buffer A) 7 0000 0000 Coefficient C195(7:0) of DAC miniDSP (DAC Buffer A) 8 0000 0000 Coefficient C196(15:8) of DAC miniDSP (DAC Buffer A) REGISTER NAME Reserved. Do not write to this register. 9 0000 0000 Coefficient C196(7:0) of DAC miniDSP (DAC Buffer A) 10 0000 0000 Coefficient C197(15:8) of DAC miniDSP (DAC Buffer A) 11 0000 0000 Coefficient C197(7:0) of DAC miniDSP (DAC Buffer A) 12 0000 0000 Coefficient C198(15:8) of DAC miniDSP (DAC Buffer A) 13 0000 0000 Coefficient C198(7:0) of DAC miniDSP (DAC Buffer A) 14 0000 0000 Coefficient C199(15:8) of DAC miniDSP (DAC Buffer A) 15 0000 0000 Coefficient C199(7:0) of DAC miniDSP (DAC Buffer A) 16 0000 0000 Coefficient C200(15:8) of DAC miniDSP (DAC Buffer A) 17 0000 0000 Coefficient C200(7:0) of DAC miniDSP (DAC Buffer A) 18 0000 0000 Coefficient C201(15:8) of DAC miniDSP (DAC Buffer A) 19 0000 0000 Coefficient C201(7:0) of DAC miniDSP (DAC Buffer A) 20 0000 0000 Coefficient C202(15:8) of DAC miniDSP (DAC Buffer A) 21 0000 0000 Coefficient C202(7:0) of DAC miniDSP (DAC Buffer A) 22 0000 0000 Coefficient C203(15:8) of DAC miniDSP (DAC Buffer A) 23 0000 0000 Coefficient C203(7:0) of DAC miniDSP (DAC Buffer A) 24 0000 0000 Coefficient C204(15:8) of DAC miniDSP (DAC Buffer A) 25 0000 0000 Coefficient C204(7:0) of DAC miniDSP (DAC Buffer A) REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-9. Page-11 Registers (continued) REGISTER NUMBER RESET VALUE 26 0000 0000 Coefficient C205(15:8) of DAC miniDSP (DAC Buffer A) 27 0000 0000 Coefficient C205(7:0) of DAC miniDSP (DAC Buffer A) 28 0000 0000 Coefficient C206(15:8) of DAC miniDSP (DAC Buffer A) 29 0000 0000 Coefficient C206(7:0) of DAC miniDSP (DAC Buffer A) 30 0000 0000 Coefficient C207(15:8) of DAC miniDSP (DAC Buffer A) 31 0000 0000 Coefficient C207(7:0) of DAC miniDSP (DAC Buffer A) 32 0000 0000 Coefficient C208(15:8) of DAC miniDSP (DAC Buffer A) 33 0000 0000 Coefficient C208(7:0) of DAC miniDSP (DAC Buffer A) 34 0000 0000 Coefficient C209(15:8) of DAC miniDSP (DAC Buffer A) 35 0000 0000 Coefficient C209(7:0) of DAC miniDSP (DAC Buffer A) 36 0000 0000 Coefficient C210(15:8) of DAC miniDSP (DAC Buffer A) 37 0000 0000 Coefficient C210(7:0) of DAC miniDSP (DAC Buffer A) 38 0000 0000 Coefficient C211(15:8) of DAC miniDSP (DAC Buffer A) 39 0000 0000 Coefficient C211(7:0) of DAC miniDSP (DAC Buffer A) 40 0000 0000 Coefficient C212(15:8) of DAC miniDSP (DAC Buffer A) 41 0000 0000 Coefficient C212(7:0) of DAC miniDSP (DAC Buffer A) 42 0000 0000 Coefficient C213(15:8) of DAC miniDSP (DAC Buffer A) 43 0000 0000 Coefficient C213(7:0) of DAC miniDSP (DAC Buffer A) 44 0000 0000 Coefficient C214(15:8) of DAC miniDSP (DAC Buffer A) 45 0000 0000 Coefficient C214(7:0) of DAC miniDSP (DAC Buffer A) 46 0000 0000 Coefficient C215(15:8) of DAC miniDSP (DAC Buffer A) 47 0000 0000 Coefficient C215(7:0) of DAC miniDSP (DAC Buffer A) 48 0000 0000 Coefficient C216(15:8) of DAC miniDSP (DAC Buffer A) 49 0000 0000 Coefficient C216(7:0) of DAC miniDSP (DAC Buffer A) 50 0000 0000 Coefficient C217(15:8) of DAC miniDSP (DAC Buffer A) 51 0000 0000 Coefficient C217(7:0) of DAC miniDSP (DAC Buffer A) 52 0000 0000 Coefficient C218(15:8) of DAC miniDSP (DAC Buffer A) 53 0000 0000 Coefficient C218(7:0) of DAC miniDSP (DAC Buffer A) 54 0000 0000 Coefficient C219(15:8) of DAC miniDSP (DAC Buffer A) 55 0000 0000 Coefficient C219(7:0) of DAC miniDSP (DAC Buffer A) 56 0000 0000 Coefficient C220(15:8) of DAC miniDSP (DAC Buffer A) 57 0000 0000 Coefficient C220(7:0) of DAC miniDSP (DAC Buffer A) 58 0000 0000 Coefficient C221(15:8) of DAC miniDSP (DAC Buffer A) 59 0000 0000 Coefficient C221(7:0) of DAC miniDSP (DAC Buffer A) 60 0000 0000 Coefficient C222(15:8) of DAC miniDSP (DAC Buffer A) 61 0000 0000 Coefficient C222(7:0) of DAC miniDSP (DAC Buffer A) 62 0000 0000 Coefficient C223(15:8) of DAC miniDSP (DAC Buffer A) 63 0000 0000 Coefficient C223(7:0) of DAC miniDSP (DAC Buffer A) 64 0000 0000 Coefficient C224(15:8) of DAC miniDSP (DAC Buffer A) 65 0000 0000 Coefficient C224(7:0) of DAC miniDSP (DAC Buffer A) 66 0000 0000 Coefficient C225(15:8) of DAC miniDSP (DAC Buffer A) 67 0000 0000 Coefficient C225(7:0) of DAC miniDSP (DAC Buffer A) 68 0000 0000 Coefficient C226(15:8) of DAC miniDSP (DAC Buffer A) 69 0000 0000 Coefficient C226(7:0) of DAC miniDSP (DAC Buffer A) 70 0000 0000 Coefficient C227(15:8) of DAC miniDSP (DAC Buffer A) 71 0000 0000 Coefficient C227(7:0) of DAC miniDSP (DAC Buffer A) 72 0000 0000 Coefficient C228(15:8) of DAC miniDSP (DAC Buffer A) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 89 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-9. Page-11 Registers (continued) 90 REGISTER NUMBER RESET VALUE 73 0000 0000 Coefficient C228(7:0) of DAC miniDSP (DAC Buffer A) 74 0000 0000 Coefficient C229(15:8) of DAC miniDSP (DAC Buffer A) 75 0000 0000 Coefficient C229(7:0) of DAC miniDSP (DAC Buffer A) 76 0000 0000 Coefficient C230(15:8) of DAC miniDSP (DAC Buffer A) 77 0000 0000 Coefficient C230(7:0) of DAC miniDSP (DAC Buffer A) 78 0000 0000 Coefficient C231(15:8) of DAC miniDSP (DAC Buffer A) 79 0000 0000 Coefficient C231(7:0) of DAC miniDSP (DAC Buffer A) 80 0000 0000 Coefficient C232(15:8) of DAC miniDSP (DAC Buffer A) 81 0000 0000 Coefficient C232(7:0) of DAC miniDSP (DAC Buffer A) 82 0000 0000 Coefficient C233(15:8) of DAC miniDSP (DAC Buffer A) 83 0000 0000 Coefficient C233(7:0) of DAC miniDSP (DAC Buffer A) 84 0000 0000 Coefficient C234(15:8) of DAC miniDSP (DAC Buffer A) 85 0000 0000 Coefficient C234(7:0) of DAC miniDSP (DAC Buffer A) 86 0000 0000 Coefficient C235(15:8) of DAC miniDSP (DAC Buffer A) 87 0000 0000 Coefficient C235(7:0) of DAC miniDSP (DAC Buffer A) 88 0000 0000 Coefficient C236(15:8) of DAC miniDSP (DAC Buffer A) 89 0000 0000 Coefficient C236(7:0) of DAC miniDSP (DAC Buffer A) 90 0000 0000 Coefficient C237(15:8) of DAC miniDSP (DAC Buffer A) 91 0000 0000 Coefficient C237(7:0) of DAC miniDSP (DAC Buffer A) 92 0000 0000 Coefficient C238(15:8) of DAC miniDSP (DAC Buffer A) 93 0000 0000 Coefficient C238(7:0) of DAC miniDSP (DAC Buffer A) 94 0000 0000 Coefficient C239(15:8) of DAC miniDSP (DAC Buffer A) 95 0000 0000 Coefficient C239(7:0) of DAC miniDSP (DAC Buffer A) 96 0000 0000 Coefficient C240(15:8) of DAC miniDSP (DAC Buffer A) 97 0000 0000 Coefficient C240(7:0) of DAC miniDSP (DAC Buffer A) 98 0000 0000 Coefficient C241(15:8) of DAC miniDSP (DAC Buffer A) REGISTER NAME 99 0000 0000 Coefficient C241(7:0) of DAC miniDSP (DAC Buffer A) 100 0000 0000 Coefficient C242(15:8) of DAC miniDSP (DAC Buffer A) 101 0000 0000 Coefficient C242(7:0) of DAC miniDSP (DAC Buffer A) 102 0000 0000 Coefficient C243(15:8) of DAC miniDSP (DAC Buffer A) 103 0000 0000 Coefficient C243(7:0) of DAC miniDSP (DAC Buffer A) 104 0000 0000 Coefficient C244(15:8) of DAC miniDSP (DAC Buffer A) 105 0000 0000 Coefficient C244(7:0) of DAC miniDSP (DAC Buffer A) 106 0000 0000 Coefficient C245(15:8) of DAC miniDSP (DAC Buffer A) 107 0000 0000 Coefficient C245(7:0) of DAC miniDSP (DAC Buffer A) 108 0000 0000 Coefficient C246(15:8) of DAC miniDSP (DAC Buffer A) 109 0000 0000 Coefficient C246(7:0) of DAC miniDSP (DAC Buffer A) 110 0000 0000 Coefficient C247(15:8) of DAC miniDSP (DAC Buffer A) 111 0000 0000 Coefficient C247(7:0) of DAC miniDSP (DAC Buffer A) 112 0000 0000 Coefficient C248(15:8) of DAC miniDSP (DAC Buffer A) 113 0000 0000 Coefficient C248(7:0) of DAC miniDSP (DAC Buffer A) 114 0000 0000 Coefficient C249(15:8) of DAC miniDSP (DAC Buffer A) 115 0000 0000 Coefficient C249(7:0) of DAC miniDSP (DAC Buffer A) 116 0000 0000 Coefficient C250(15:8) of DAC miniDSP (DAC Buffer A) 117 0000 0000 Coefficient C250(7:0) of DAC miniDSP (DAC Buffer A) 118 0000 0000 Coefficient C251(15:8) of DAC miniDSP (DAC Buffer A) 119 0000 0000 Coefficient C251(7:0) of DAC miniDSP (DAC Buffer A) REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-9. Page-11 Registers (continued) REGISTER NUMBER RESET VALUE 120 0000 0000 Coefficient C252(15:8) of DAC miniDSP (DAC Buffer A) 121 0000 0000 Coefficient C252(7:0) of DAC miniDSP (DAC Buffer A) 122 0000 0000 Coefficient C253(15:8) of DAC miniDSP (DAC Buffer A) 123 0000 0000 Coefficient C253(7:0) of DAC miniDSP (DAC Buffer A) 124 0000 0000 Coefficient C254(15:8) of DAC miniDSP (DAC Buffer A) 125 0000 0000 Coefficient C254(7:0) of DAC miniDSP (DAC Buffer A) 126 0000 0000 Coefficient C255(15:8) of DAC miniDSP (DAC Buffer A) 127 0000 0000 Coefficient C255(7:0) of DAC miniDSP (DAC Buffer A) 6.9 REGISTER NAME Control Registers, Page 12: DAC Programmable Coefficients RAM Buffer B (1:63) Table 6-10. Page-12 Registers REGISTER NUMBER RESET VALUE 1 0000 0000 Reserved. Do not write to this register. 2 0111 1111 Coefficient NO(15:8) for left DAC-programmable biquad A or Coefficient C1(15:8) of DAC miniDSP (DAC Buffer B) 3 1111 1111 Coefficient NO(7:0) for left DAC-programmable biquad A or Coefficient C1(7:0) of DAC miniDSP (DAC Buffer B) 4 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad A or Coefficient C2(15:8) of DAC miniDSP (DAC Buffer B) 5 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad A or Coefficient C2(7:0) of DAC miniDSP (DAC Buffer B) 6 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad A or Coefficient C3(15:8) of DAC miniDSP (DAC Buffer B) 7 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad A or Coefficient C3(7:0) of DAC miniDSP (DAC Buffer B) 8 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad A or Coefficient C4(15:8) of DAC miniDSP (DAC Buffer B) 9 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad A or Coefficient C4(7:0) of DAC miniDSP (DAC Buffer B) 10 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad A or Coefficient C5(15:8) of DAC miniDSP (DAC Buffer B) 11 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad A or Coefficient C5(7:0) of DAC miniDSP (DAC Buffer B) 12 0111 1111 Coefficient NO(15:8) for left DAC-programmable biquad B or Coefficient C6(15:8) of DAC miniDSP (DAC Buffer B) 13 1111 1111 Coefficient NO(7:0) for left DAC-programmable biquad B or Coefficient C6(7:0) of DAC miniDSP (DAC Buffer B) 14 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad B or Coefficient C7(15:8) of DAC miniDSP (DAC Buffer B) 15 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad B or Coefficient C7(7:0) of DAC miniDSP (DAC Buffer B) 16 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad B or Coefficient C8(15:8) of DAC miniDSP (DAC Buffer B) 17 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad B or Coefficient C8(7:0) of DAC miniDSP (DAC Buffer B) 18 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad B or Coefficient C9(15:8) of DAC miniDSP (DAC Buffer B) 19 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad B or Coefficient C9(7:0) of DAC miniDSP (DAC Buffer B) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 91 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-10. Page-12 Registers (continued) 92 REGISTER NUMBER RESET VALUE 20 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad B or Coefficient C10(15:8) of DAC miniDSP (DAC Buffer B) 21 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad B or Coefficient C10(7:0) of DAC miniDSP (DAC Buffer B) 22 0111 1111 Coefficient NO(15:8) for left DAC-programmable biquad C or Coefficient C11(15:8) of DAC miniDSP (DAC Buffer B) 23 1111 1111 Coefficient NO(7:0) for left DAC-programmable biquad C or Coefficient C11(7:0) of DAC miniDSP (DAC Buffer B) 24 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad C or Coefficient C12(15:8) of DAC miniDSP (DAC Buffer B) 25 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad C or Coefficient C12(7:0) of DAC miniDSP (DAC Buffer B) 26 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad C or Coefficient C13(15:8) of DAC miniDSP (DAC Buffer B) 27 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad C or Coefficient C13(7:0) of DAC miniDSP (DAC Buffer B) 28 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad C or Coefficient C14(15:8) of DAC miniDSP (DAC Buffer B) 29 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad C or Coefficient C14(7:0) of DAC miniDSP (DAC Buffer B) 30 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad C or Coefficient C15(15:8) of DAC miniDSP (DAC Buffer B) 31 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad C or Coefficient C15(7:0) of DAC miniDSP (DAC Buffer B) 32 0111 1111 Coefficient NO(15:8) for left DAC-programmable biquad D or Coefficient C16(15:8) of DAC miniDSP (DAC Buffer B) 33 1111 1111 Coefficient NO(7:0) for left DAC-programmable biquad D or Coefficient C16(7:0) of DAC miniDSP (DAC Buffer B) 34 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad D or Coefficient C17(15:8) of DAC miniDSP (DAC Buffer B) 35 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad D or Coefficient C17(7:0) of DAC miniDSP (DAC Buffer B) 36 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad D or Coefficient C18(15:8) of DAC miniDSP (DAC Buffer B) 37 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad D or Coefficient C18(7:0) of DAC miniDSP (DAC Buffer B) 38 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad D or Coefficient C19(15:8) of DAC miniDSP (DAC Buffer B) 39 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad D or Coefficient C19(7:0) of DAC miniDSP (DAC Buffer B) 40 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad D or Coefficient C20(15:8) of DAC miniDSP (DAC Buffer B) 41 0000 0000 Coefficient D2(17:0) for left DAC-programmable biquad D or Coefficient C20(7:0) of DAC miniDSP (DAC Buffer B) 42 0111 1111 Coefficient NO(15:8) for left DAC-programmable biquad E or Coefficient C21(15:8) of DAC miniDSP (DAC Buffer B) 43 1111 1111 Coefficient NO(7:0) for left DAC-programmable biquad E or Coefficient C21(7:0) of DAC miniDSP (DAC Buffer B) 44 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad E or Coefficient C22(15:8) of DAC miniDSP (DAC Buffer B) 45 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad E or Coefficient C22(7:0) of DAC miniDSP (DAC Buffer B) 46 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad E or Coefficient C23(15:8) of DAC miniDSP (DAC Buffer B) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-10. Page-12 Registers (continued) REGISTER NUMBER RESET VALUE 47 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad E or Coefficient C23(7:0) of DAC miniDSP (DAC Buffer B) 48 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad E or Coefficient C24(15:8) of DAC miniDSP (DAC Buffer B) 49 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad E or Coefficient C24(7:0) of DAC miniDSP (DAC Buffer B) 50 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad E or Coefficient C25(15:8) of DAC miniDSP (DAC Buffer B) 51 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad E or Coefficient C25(7:0) of DAC miniDSP (DAC Buffer B) 52 0111 1111 Coefficient NO(15:8) for left DAC-programmable biquad F or Coefficient C26(15:8) of DAC miniDSP (DAC Buffer B) 53 1111 1111 Coefficient NO(7:0) for left DAC-programmable biquad F or Coefficient C26(7:0) of DAC miniDSP (DAC Buffer B) 54 0000 0000 Coefficient N1(15:8) for left DAC-programmable biquad F or Coefficient C27(15:8) of DAC miniDSP (DAC Buffer B) 55 0000 0000 Coefficient N1(7:0) for left DAC-programmable biquad F or Coefficient C27(7:0) of DAC miniDSP (DAC Buffer B) 56 0000 0000 Coefficient N2(15:8) for left DAC-programmable biquad F or Coefficient C28(15:8) of DAC miniDSP (DAC Buffer B) 57 0000 0000 Coefficient N2(7:0) for left DAC-programmable biquad F or Coefficient C28(7:0) of DAC miniDSP (DAC Buffer B) 58 0000 0000 Coefficient D1(15:8) for left DAC-programmable biquad F or Coefficient C29(15:8) of DAC miniDSP (DAC Buffer B) 59 0000 0000 Coefficient D1(7:0) for left DAC-programmable biquad F or Coefficient C29(7:0) of DAC miniDSP (DAC Buffer B) 60 0000 0000 Coefficient D2(15:8) for left DAC-programmable biquad F or Coefficient C30(15:8) of DAC miniDSP (DAC Buffer B) 61 0000 0000 Coefficient D2(7:0) for left DAC-programmable biquad F or Coefficient C30(7:0) of DAC miniDSP (DAC Buffer B) 62 0000 0000 Coefficient C31(15:8) of DAC miniDSP (DAC Buffer B) 63 0000 0000 Coefficient C31(7:0) of DAC miniDSP (DAC Buffer B) 64 0000 0000 Coefficient C32(15:8) of DAC miniDSP (DAC Buffer B)– also used for the 3D PGA for PRB_P23, PRB_P24 and PRB_P25 65 0000 0000 Coefficient C32(7:0) of DAC miniDSP (DAC Buffer B) – also used for the 3D PGA for PRB_P23, PRB_P24 and PRB_P25 66 0111 1111 Reserved. 67 1111 1111 Reserved. 68 0000 0000 Reserved. 69 0000 0000 Reserved. 70 0000 0000 Reserved. 71 0000 0000 Reserved. 72 0000 0000 Reserved. 73 0000 0000 Reserved. 74 0000 0000 Reserved. 75 0000 0000 Reserved. 76 0111 1111 Reserved. 77 1111 1111 Reserved. 78 0000 0000 Reserved. 79 0000 0000 Reserved. 80 0000 0000 Reserved. 81 0000 0000 Reserved. REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 93 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-10. Page-12 Registers (continued) 94 REGISTER NUMBER RESET VALUE 82 0000 0000 Reserved. 83 0000 0000 Reserved. 84 0000 0000 Reserved. 85 0000 0000 Reserved. 86 0111 1111 Reserved. 87 1111 1111 Reserved. 88 0000 0000 Reserved. 89 0000 0000 Reserved. 90 0000 0000 Reserved. 91 0000 0000 Reserved. 92 0000 0000 Reserved. 93 0000 0000 Reserved. 94 0000 0000 Reserved. 95 0000 0000 Reserved. 96 0111 1111 Reserved. 97 1111 1111 Reserved. 98 0000 0000 Reserved. 99 0000 0000 Reserved. 100 0000 0000 Reserved. 101 0000 0000 Reserved. 102 0000 0000 Reserved. 103 0000 0000 Reserved. 104 0000 0000 Reserved. 105 0000 0000 Reserved. 106 0111 1111 Reserved. 107 1111 1111 Reserved. 108 0000 0000 Reserved. 109 0000 0000 Reserved. 110 0000 0000 Reserved. 111 0000 0000 Reserved. 112 0000 0000 Reserved. 113 0000 0000 Reserved. 114 0000 0000 Reserved. 115 0000 0000 Reserved. 116 0111 1111 Reserved. 117 1111 1111 Reserved. 118 0000 0000 Reserved. 119 0000 0000 Reserved. 120 0000 0000 Reserved. 121 0000 0000 Reserved. 122 0000 0000 Reserved. 123 0000 0000 Reserved. 124 0000 0000 Reserved. 125 0000 0000 Reserved. 126 0000 0000 Reserved. 127 0000 0000 Reserved. REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 6.10 Control Registers, Page 13: DAC Programmable Coefficients RAM Buffer B (65:127) Table 6-11. Page-13 Registers REGISTER NUMBER RESET VALUE 1 0000 0000 Reserved. Do not write to this register. 2 0111 1111 Coefficient N0(15:8) for left DAC-programmable first-order IIR or Coefficient C65(15:8) of DAC miniDSP (DAC Buffer B) 3 1111 1111 Coefficient N0(7:0) for left DAC-programmable first-order IIR or Coefficient C65(7:0) of DAC miniDSP (DAC Buffer B) 4 0000 0000 Coefficient N1(15:8) for left DAC-programmable first-order IIR or Coefficient C66(15:8) of DAC miniDSP (DAC Buffer B) 5 0000 0000 Coefficient N1(7:0) for left DAC-programmable first-order IIR or Coefficient C66(7:0) of DAC miniDSP (DAC Buffer B) 6 0000 0000 Coefficient D1(15:8) for left DAC-programmable first-order IIR or Coefficient C67(15:8) of DAC miniDSP (DAC Buffer B) 7 0000 0000 Coefficient D1(7:0) for left DAC-programmable first-order IIR or Coefficient C67(7:0) of DAC miniDSP (DAC Buffer B) 8 0111 1111 Reserved. 9 1111 1111 Reserved. 10 0000 0000 Reserved. 11 0000 0000 Reserved. 12 0000 0000 Reserved. 13 0000 0000 Reserved. 14 0111 1111 Coefficient N0(15:8) for DRC first-order high-pass filter or Coefficient C71(15:8) of DAC miniDSP (DAC Buffer B) 15 1111 0111 Coefficient N0(7:0) for DRC first-order high-pass filter or Coefficient C71(7:0) of DAC miniDSP (DAC Buffer B) 16 1000 0000 Coefficient N1(15:8) for DRC first-order high-pass filter or Coefficient C72(15:8) of DAC miniDSP (DAC Buffer B) 17 0000 1001 Coefficient N1(7:0) for DRC first-order high-pass filter or Coefficient C72(7:0) of DAC miniDSP (DAC Buffer B) 18 0111 1111 Coefficient D1(15:8) for DRC first-order high-pass filter or Coefficient C73(15:8) of DAC miniDSP (DAC Buffer B) 19 1110 1111 Coefficient D1(7:0) for DRC first-order high-pass filter or Coefficient C73(7:0) of DAC miniDSP (DAC Buffer B) 20 0000 0000 Coefficient N0(15:8) for DRC first-order low-pass filter or Coefficient C74(15:8) of DAC miniDSP (DAC Buffer B) 21 0001 0001 Coefficient N0(7:0) for DRC first-order low-pass filter or Coefficient C74(7:0) of DAC miniDSP (DAC Buffer B) 22 0000 0000 Coefficient N1(15:8) for DRC first-order low-pass filter or Coefficient C75(15:8) of DAC miniDSP (DAC Buffer B) 23 0001 0001 Coefficient N1(7:0) for DRC first-order low-pass filter or Coefficient C75(7:0) of DAC miniDSP (DAC Buffer B) 24 0111 1111 Coefficient D1(15:8) for DRC first-order low-pass filter or Coefficient C76(15:8) of DAC miniDSP (DAC Buffer B) 25 1101 1110 Coefficient D1(7:0) for DRC first-order low-pass filter or Coefficient C76(7:0) of DAC miniDSP (DAC Buffer B) 26 0000 0000 Coefficient C77(15:8) of DAC miniDSP (DAC Buffer B) 27 0000 0000 Coefficient C77(7:0) of DAC miniDSP (DAC Buffer B) 28 0000 0000 Coefficient C78(15:8) of DAC miniDSP (DAC Buffer B) 29 0000 0000 Coefficient C78(7:0) of DAC miniDSP (DAC Buffer B) 30 0000 0000 Coefficient C79(15:8) of DAC miniDSP (DAC Buffer B) 31 0000 0000 Coefficient C79(7:0) of DAC miniDSP (DAC Buffer B) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 95 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-11. Page-13 Registers (continued) 96 REGISTER NUMBER RESET VALUE 32 0000 0000 Coefficient C80(15:8) of DAC miniDSP (DAC Buffer B) 33 0000 0000 Coefficient C80(7:0) of DAC miniDSP (DAC Buffer B) 34 0000 0000 Coefficient C81(15:8) of DAC miniDSP (DAC Buffer B) 35 0000 0000 Coefficient C81(7:0) of DAC miniDSP (DAC Buffer B) 36 0000 0000 Coefficient C82(15:8) of DAC miniDSP (DAC Buffer B) 37 0000 0000 Coefficient C82(7:0) of DAC miniDSP (DAC Buffer B) 38 0000 0000 Coefficient C83(15:8) of DAC miniDSP (DAC Buffer B) 39 0000 0000 Coefficient C83(7:0) of DAC miniDSP (DAC Buffer B) 40 0000 0000 Coefficient C84(15:8) of DAC miniDSP (DAC Buffer B) 41 0000 0000 Coefficient C84(7:0) of DAC miniDSP (DAC Buffer B) 42 0000 0000 Coefficient C85(15:8) of DAC miniDSP (DAC Buffer B) 43 0000 0000 Coefficient C85(7:0) of DAC miniDSP (DAC Buffer B) 44 0000 0000 Coefficient C86(15:8) of DAC miniDSP (DAC Buffer B) 45 0000 0000 Coefficient C86(7:0) of DAC miniDSP (DAC Buffer B) 46 0000 0000 Coefficient C87(15:8) of DAC miniDSP (DAC Buffer B) 47 0000 0000 Coefficient C87(7:0) of DAC miniDSP (DAC Buffer B) 48 0000 0000 Coefficient C88(15:8) of DAC miniDSP (DAC Buffer B) 49 0000 0000 Coefficient C88(7:0) of DAC miniDSP (DAC Buffer B) 50 0000 0000 Coefficient C89(15:8) of DAC miniDSP (DAC Buffer B) 51 0000 0000 Coefficient C89(7:0) of DAC miniDSP (DAC Buffer B) 52 0000 0000 Coefficient C90(15:8) of DAC miniDSP (DAC Buffer B) 53 0000 0000 Coefficient C90(7:0) of DAC miniDSP (DAC Buffer B) 54 0000 0000 Coefficient C91(15:8) of DAC miniDSP (DAC Buffer B) 55 0000 0000 Coefficient C91(7:0) of DAC miniDSP (DAC Buffer B) 56 0000 0000 Coefficient C92(15:8) of DAC miniDSP (DAC Buffer B) 57 0000 0000 Coefficient C92(7:0) of DAC miniDSP (DAC Buffer B) 58 0000 0000 Coefficient C93(15:8) of DAC miniDSP (DAC Buffer B) 59 0000 0000 Coefficient C93(7:0) of DAC miniDSP (DAC Buffer B) 60 0000 0000 Coefficient C94(15:8) of DAC miniDSP (DAC Buffer B) 61 0000 0000 Coefficient C94(7:0) of DAC miniDSP (DAC Buffer B) 62 0000 0000 Coefficient C95(15:8) of DAC miniDSP (DAC Buffer B) 63 0000 0000 Coefficient C95(7:0) of DAC miniDSP (DAC Buffer B) 64 0000 0000 Coefficient C96(15:8) of DAC miniDSP (DAC Buffer B) 65 0000 0000 Coefficient C96(7:0) of DAC miniDSP (DAC Buffer B) 66 0000 0000 Coefficient C97(15:8) of DAC miniDSP (DAC Buffer B) 67 0000 0000 Coefficient C97(7:0) of DAC miniDSP (DAC Buffer B) 68 0000 0000 Coefficient C98(15:8) of DAC miniDSP (DAC Buffer B) 69 0000 0000 Coefficient C98(7:0) of DAC miniDSP (DAC Buffer B) 70 0000 0000 Coefficient C99(15:8) of DAC miniDSP (DAC Buffer B) 71 0000 0000 Coefficient C99(7:0) of DAC miniDSP (DAC Buffer B) 72 0000 0000 Coefficient C100(15:8) of DAC miniDSP (DAC Buffer B) 73 0000 0000 Coefficient C100(7:0) of DAC miniDSP (DAC Buffer B) 74 0000 0000 Coefficient C101(15:8) of DAC miniDSP (DAC Buffer B) 75 0000 0000 Coefficient C101(7:0) of DAC miniDSP (DAC Buffer B) 76 0000 0000 Coefficient C102(15:8) of DAC miniDSP (DAC Buffer B) 77 0000 0000 Coefficient C102(7:0) of DAC miniDSP (DAC Buffer B) 78 0000 0000 Coefficient C103(15:8) of DAC miniDSP (DAC Buffer B) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-11. Page-13 Registers (continued) REGISTER NUMBER RESET VALUE 79 0000 0000 Coefficient C103(7:0) of DAC miniDSP (DAC Buffer B) 80 0000 0000 Coefficient C104(15:8) of DAC miniDSP (DAC Buffer B) 81 0000 0000 Coefficient C104(7:0) of DAC miniDSP (DAC Buffer B) 82 0000 0000 Coefficient C105(15:8) of DAC miniDSP (DAC Buffer B) 83 0000 0000 Coefficient C105(7:0) of DAC miniDSP (DAC Buffer B) 84 0000 0000 Coefficient C106(15:8) of DAC miniDSP (DAC Buffer B) 85 0000 0000 Coefficient C106(7:0) of DAC miniDSP (DAC Buffer B) 86 0000 0000 Coefficient C107(15:8) of DAC miniDSP (DAC Buffer B) 87 0000 0000 Coefficient C107(7:0) of DAC miniDSP (DAC Buffer B) 88 0000 0000 Coefficient C108(15:8) of DAC miniDSP (DAC Buffer B) 89 0000 0000 Coefficient C108(7:0) of DAC miniDSP (DAC Buffer B) 90 0000 0000 Coefficient C109(15:8) of DAC miniDSP (DAC Buffer B) 91 0000 0000 Coefficient C109(7:0) of DAC miniDSP (DAC Buffer B) 92 0000 0000 Coefficient C110(15:8) of DAC miniDSP (DAC Buffer B) 93 0000 0000 Coefficient C110(7:0) of DAC miniDSP (DAC Buffer B) 94 0000 0000 Coefficient C111(15:8) of DAC miniDSP (DAC Buffer B) 95 0000 0000 Coefficient C111(7:0) of DAC miniDSP (DAC Buffer B) 96 0000 0000 Coefficient C112(15:8) of DAC miniDSP (DAC Buffer B) 97 0000 0000 Coefficient C112(7:0) of DAC miniDSP (DAC Buffer B) 98 0000 0000 Coefficient C113(15:8) of DAC miniDSP (DAC Buffer B) REGISTER NAME 99 0000 0000 Coefficient C113(7:0) of DAC miniDSP (DAC Buffer B) 100 0000 0000 Coefficient C114(15:8) of DAC miniDSP (DAC Buffer B) 101 0000 0000 Coefficient C114(7:0) of DAC miniDSP (DAC Buffer B) 102 0000 0000 Coefficient C115(15:8) of DAC miniDSP (DAC Buffer B) 103 0000 0000 Coefficient C116(7:0) of DAC miniDSP (DAC Buffer B) 104 0000 0000 Coefficient C117(15:8) of DAC miniDSP (DAC Buffer B) 105 0000 0000 Coefficient C117(7:0) of DAC miniDSP (DAC Buffer B) 106 0000 0000 Coefficient C118(15:8) of DAC miniDSP (DAC Buffer B) 107 0000 0000 Coefficient C118(7:0) of DAC miniDSP (DAC Buffer B) 108 0000 0000 Coefficient C119(15:8) of DAC miniDSP (DAC Buffer B) 109 0000 0000 Coefficient C119(7:0) of DAC miniDSP (DAC Buffer B) 110 0000 0000 Coefficient C120(15:8) of DAC miniDSP (DAC Buffer B) 111 0000 0000 Coefficient C120(7:0) of DAC miniDSP (DAC Buffer B) 112 0000 0000 Coefficient C121(15:8) of DAC miniDSP (DAC Buffer B) 113 0000 0000 Coefficient C121(7:0) of DAC miniDSP (DAC Buffer B) 114 0000 0000 Coefficient C122(15:8) of DAC miniDSP (DAC Buffer B) 115 0000 0000 Coefficient C122(7:0) of DAC miniDSP (DAC Buffer B) 116 0000 0000 Coefficient C123(15:8) of DAC miniDSP (DAC Buffer B) 117 0000 0000 Coefficient C123(7:0) of DAC miniDSP (DAC Buffer B) 118 0000 0000 Coefficient C123(15:8) of DAC miniDSP (DAC Buffer B) 119 0000 0000 Coefficient C123(7:0) of DAC miniDSP (DAC Buffer B) 120 0000 0000 Coefficient C124(15:8) of DAC miniDSP (DAC Buffer B) 121 0000 0000 Coefficient C124(7:0) of DAC miniDSP (DAC Buffer B) 122 0000 0000 Coefficient C125(15:8) of DAC miniDSP (DAC Buffer B) 123 0000 0000 Coefficient C125(7:0) of DAC miniDSP (DAC Buffer B) 124 0000 0000 Coefficient C126(15:8) of DAC miniDSP (DAC Buffer B) 125 0000 0000 Coefficient C126(7:0) of DAC miniDSP (DAC Buffer B) REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 97 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-11. Page-13 Registers (continued) REGISTER NUMBER RESET VALUE 126 0000 0000 Coefficient C127(15:8) of DAC miniDSP (DAC Buffer B) 127 0000 0000 Coefficient C127(7:0) of DAC miniDSP (DAC Buffer B) REGISTER NAME 6.11 Control Registers, Page 14: DAC Programmable Coefficients RAM Buffer B (129:191) Table 6-12. Page-14 Registers 98 REGISTER NUMBER RESET VALUE 1 XXXX XXXX 2 0000 0000 Coefficient C129(15:8) of DAC miniDSP (DAC Buffer B) 3 0000 0000 Coefficient C129(7:0) of DAC miniDSP (DAC Buffer B) 4 0000 0000 Coefficient C130(15:8) of DAC miniDSP (DAC Buffer B) 5 0000 0000 Coefficient C130(7:0) of DAC miniDSP (DAC Buffer B) 6 0000 0000 Coefficient C131(15:8) of DAC miniDSP (DAC Buffer B) 7 0000 0000 Coefficient C131(7:0) of DAC miniDSP (DAC Buffer B) 8 0000 0000 Coefficient C132(15:8) of DAC miniDSP (DAC Buffer B) 9 0000 0000 Coefficient C132(7:0) of DAC miniDSP (DAC Buffer B) 10 0000 0000 Coefficient C133(15:8) of DAC miniDSP (DAC Buffer B) 11 0000 0000 Coefficient C133(7:0) of DAC miniDSP (DAC Buffer B) 12 0000 0000 Coefficient C134(15:8) of DAC miniDSP (DAC Buffer B) 13 0000 0000 Coefficient C134(7:0) of DAC miniDSP (DAC Buffer B) 14 0000 0000 Coefficient C135(15:8) of DAC miniDSP (DAC Buffer B) 15 0000 0000 Coefficient C135(7:0) of DAC miniDSP (DAC Buffer B) 16 0000 0000 Coefficient C136(15:8) of DAC miniDSP (DAC Buffer B) 17 0000 0000 Coefficient C136(7:0) of DAC miniDSP (DAC Buffer B) 18 0000 0000 Coefficient C137(15:8) of DAC miniDSP (DAC Buffer B) 19 0000 0000 Coefficient C137(7:0) of DAC miniDSP (DAC Buffer B) 20 0000 0000 Coefficient C138(15:8) of DAC miniDSP (DAC Buffer B) 21 0000 0000 Coefficient C138(7:0) of DAC miniDSP (DAC Buffer B) 22 0000 0000 Coefficient C139(15:8) of DAC miniDSP (DAC Buffer B) 23 0000 0000 Coefficient C139(7:0) of DAC miniDSP (DAC Buffer B) 24 0000 0000 Coefficient C140(15:8) of DAC miniDSP (DAC Buffer B) 25 0000 0000 Coefficient C140(7:0) of DAC miniDSP (DAC Buffer B) 26 0000 0000 Coefficient C141(15:8) of DAC miniDSP (DAC Buffer B) 27 0000 0000 Coefficient C141(7:0) of DAC miniDSP (DAC Buffer B) 28 0000 0000 Coefficient C142(15:8) of DAC miniDSP (DAC Buffer B) 29 0000 0000 Coefficient C142(7:0) of DAC miniDSP (DAC Buffer B) 30 0000 0000 Coefficient C143(15:8) of DAC miniDSP (DAC Buffer B) 31 0000 0000 Coefficient C143(7:0) of DAC miniDSP (DAC Buffer B) 32 0000 0000 Coefficient C144(15:8) of DAC miniDSP (DAC Buffer B) 33 0000 0000 Coefficient C144(7:0) of DAC miniDSP (DAC Buffer B) 34 0000 0000 Coefficient C145(15:8) of DAC miniDSP (DAC Buffer B) 35 0000 0000 Coefficient C145(7:0) of DAC miniDSP (DAC Buffer B) 36 0000 0000 Coefficient C146(15:8) of DAC miniDSP (DAC Buffer B) 37 0000 0000 Coefficient C146(7:0) of DAC miniDSP (DAC Buffer B) REGISTER NAME Reserved. Do not write to this register. REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-12. Page-14 Registers (continued) REGISTER NUMBER RESET VALUE 38 0000 0000 Coefficient C147(15:8) of DAC miniDSP (DAC Buffer B) 39 0000 0000 Coefficient C147(7:0) of DAC miniDSP (DAC Buffer B) 40 0000 0000 Coefficient C148(15:8) of DAC miniDSP (DAC Buffer B) 41 0000 0000 Coefficient C148(7:0) of DAC miniDSP (DAC Buffer B) 42 0000 0000 Coefficient C149(15:8) of DAC miniDSP (DAC Buffer B) 43 0000 0000 Coefficient C149(7:0) of DAC miniDSP (DAC Buffer B) 44 0000 0000 Coefficient C150(15:8) of DAC miniDSP (DAC Buffer B) 45 0000 0000 Coefficient C150(7:0) of DAC miniDSP (DAC Buffer B) 46 0000 0000 Coefficient C151(15:8) of DAC miniDSP (DAC Buffer B) 47 0000 0000 Coefficient C151(7:0) of DAC miniDSP (DAC Buffer B) 48 0000 0000 Coefficient C152(15:8) of DAC miniDSP (DAC Buffer B) 49 0000 0000 Coefficient C152(7:0) of DAC miniDSP (DAC Buffer B) 50 0000 0000 Coefficient C153(15:8) of DAC miniDSP (DAC Buffer B) 51 0000 0000 Coefficient C153(7:0) of DAC miniDSP (DAC Buffer B) 52 0000 0000 Coefficient C154(15:8) of DAC miniDSP (DAC Buffer B) 53 0000 0000 Coefficient C154(7:0) of DAC miniDSP (DAC Buffer B) 54 0000 0000 Coefficient C155(15:8) of DAC miniDSP (DAC Buffer B) 55 0000 0000 Coefficient C155(7:0) of DAC miniDSP (DAC Buffer B) 56 0000 0000 Coefficient C156(15:8) of DAC miniDSP (DAC Buffer B) 57 0000 0000 Coefficient C156(7:0) of DAC miniDSP (DAC Buffer B) 58 0000 0000 Coefficient C157(15:8) of DAC miniDSP (DAC Buffer B) 59 0000 0000 Coefficient C157(7:0) of DAC miniDSP (DAC Buffer B) 60 0000 0000 Coefficient C158(15:8) of DAC miniDSP (DAC Buffer B) 61 0000 0000 Coefficient C158(7:0) of DAC miniDSP (DAC Buffer B) 62 0000 0000 Coefficient C159(15:8) of DAC miniDSP (DAC Buffer B) 63 0000 0000 Coefficient C159(7:0) of DAC miniDSP (DAC Buffer B) 64 0000 0000 Coefficient C160(15:8) of DAC miniDSP (DAC Buffer B) 65 0000 0000 Coefficient C160(7:0) of DAC miniDSP (DAC Buffer B) 66 0000 0000 Coefficient C161(15:8) of DAC miniDSP (DAC Buffer B) 67 0000 0000 Coefficient C161(7:0) of DAC miniDSP (DAC Buffer B) 68 0000 0000 Coefficient C162(15:8) of DAC miniDSP (DAC Buffer B) 69 0000 0000 Coefficient C162(7:0) of DAC miniDSP (DAC Buffer B) 70 0000 0000 Coefficient C163(15:8) of DAC miniDSP (DAC Buffer B) 71 0000 0000 Coefficient C163(7:0) of DAC miniDSP (DAC Buffer B) 72 0000 0000 Coefficient C164(15:8) of DAC miniDSP (DAC Buffer B) 73 0000 0000 Coefficient C164(7:0) of DAC miniDSP (DAC Buffer B) 74 0000 0000 Coefficient C165(15:8) of DAC miniDSP (DAC Buffer B) 75 0000 0000 Coefficient C165(7:0) of DAC miniDSP (DAC Buffer B) 76 0000 0000 Coefficient C166(15:8) of DAC miniDSP (DAC Buffer B) 77 0000 0000 Coefficient C166(7:0) of DAC miniDSP (DAC Buffer B) 78 0000 0000 Coefficient C167(15:8) of DAC miniDSP (DAC Buffer B) 79 0000 0000 Coefficient C167(7:0) of DAC miniDSP (DAC Buffer B) 80 0000 0000 Coefficient C168(15:8) of DAC miniDSP (DAC Buffer B) 81 0000 0000 Coefficient C168(7:0) of DAC miniDSP (DAC Buffer B) 82 0000 0000 Coefficient C169(15:8) of DAC miniDSP (DAC Buffer B) 83 0000 0000 Coefficient C169(7:0) of DAC miniDSP (DAC Buffer B) 84 0000 0000 Coefficient C170(15:8) of DAC miniDSP (DAC Buffer B) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 99 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-12. Page-14 Registers (continued) 100 REGISTER NUMBER RESET VALUE 85 0000 0000 Coefficient C170(7:0) of DAC miniDSP (DAC Buffer B) 86 0000 0000 Coefficient C171(15:8) of DAC miniDSP (DAC Buffer B) 87 0000 0000 Coefficient C171(7:0) of DAC miniDSP (DAC Buffer B) 88 0000 0000 Coefficient C172(15:8) of DAC miniDSP (DAC Buffer B) 89 0000 0000 Coefficient C172(7:0) of DAC miniDSP (DAC Buffer B) 90 0000 0000 Coefficient C173(15:8) of DAC miniDSP (DAC Buffer B) 91 0000 0000 Coefficient C173(7:0) of DAC miniDSP (DAC Buffer B) 92 0000 0000 Coefficient C174(15:8) of DAC miniDSP (DAC Buffer B) 93 0000 0000 Coefficient C174(7:0) of DAC miniDSP (DAC Buffer B) 94 0000 0000 Coefficient C175(15:8) of DAC miniDSP (DAC Buffer B) 95 0000 0000 Coefficient C175(7:0) of DAC miniDSP (DAC Buffer B) 96 0000 0000 Coefficient C176(15:8) of DAC miniDSP (DAC Buffer B) 97 0000 0000 Coefficient C176(7:0) of DAC miniDSP (DAC Buffer B) 98 0000 0000 Coefficient C177(15:8) of DAC miniDSP (DAC Buffer B) 99 0000 0000 Coefficient C177(7:0) of DAC miniDSP (DAC Buffer B) 100 0000 0000 Coefficient C178(15:8) of DAC miniDSP (DAC Buffer B) 101 0000 0000 Coefficient C178(7:0) of DAC miniDSP (DAC Buffer B) 102 0000 0000 Coefficient C179(15:8) of DAC miniDSP (DAC Buffer B) 103 0000 0000 Coefficient C179(7:0) of DAC miniDSP (DAC Buffer B) 104 0000 0000 Coefficient C180(15:8) of DAC miniDSP (DAC Buffer B) 105 0000 0000 Coefficient C180(7:0) of DAC miniDSP (DAC Buffer B) 106 0000 0000 Coefficient C181(15:8) of DAC miniDSP (DAC Buffer B) 107 0000 0000 Coefficient C181(7:0) of DAC miniDSP (DAC Buffer B) 108 0000 0000 Coefficient C182(15:8) of DAC miniDSP (DAC Buffer B) 109 0000 0000 Coefficient C182(7:0) of DAC miniDSP (DAC Buffer B) 110 0000 0000 Coefficient C183(15:8) of DAC miniDSP (DAC Buffer B) 111 0000 0000 Coefficient C183(7:0) of DAC miniDSP (DAC Buffer B) 112 0000 0000 Coefficient C184(15:8) of DAC miniDSP (DAC Buffer B) 113 0000 0000 Coefficient C184(7:0) of DAC miniDSP (DAC Buffer B) 114 0000 0000 Coefficient C185(15:8) of DAC miniDSP (DAC Buffer B) 115 0000 0000 Coefficient C185(7:0) of DAC miniDSP (DAC Buffer B) 116 0000 0000 Coefficient C186(15:8) of DAC miniDSP (DAC Buffer B) 117 0000 0000 Coefficient C186(7:0) of DAC miniDSP (DAC Buffer B) 118 0000 0000 Coefficient C187(15:8) of DAC miniDSP (DAC Buffer B) 119 0000 0000 Coefficient C187(7:0) of DAC miniDSP (DAC Buffer B) 120 0000 0000 Coefficient C188(15:8) of DAC miniDSP (DAC Buffer B) 121 0000 0000 Coefficient C188(7:0) of DAC miniDSP (DAC Buffer B) 122 0000 0000 Coefficient C189(15:8) of DAC miniDSP (DAC Buffer B) 123 0000 0000 Coefficient C189(7:0) of DAC miniDSP (DAC Buffer B) 124 0000 0000 Coefficient C190(15:8) of DAC miniDSP (DAC Buffer B) 125 0000 0000 Coefficient C190(7:0) of DAC miniDSP (DAC Buffer B) 126 0000 0000 Coefficient C191(15:8) of DAC miniDSP (DAC Buffer B) 127 0000 0000 Coefficient C191(7:0) of DAC miniDSP (DAC Buffer B) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 6.12 Control Registers, Page 15: DAC Programmable Coefficients RAM Buffer B (193:255) Table 6-13. Page-15 Registers REGISTER NUMBER RESET VALUE 1 XXXX XXXX 2 0000 0000 Coefficient C193(15:8) of DAC miniDSP (DAC Buffer B) 3 0000 0000 Coefficient C193(7:0) of DAC miniDSP (DAC Buffer B) 4 0000 0000 Coefficient C194(15:8) of DAC miniDSP (DAC Buffer B) 5 0000 0000 Coefficient C194(7:0) of DAC miniDSP (DAC Buffer B) 6 0000 0000 Coefficient C195(15:8) of DAC miniDSP (DAC Buffer B) 7 0000 0000 Coefficient C195(7:0) of DAC miniDSP (DAC Buffer B) 8 0000 0000 Coefficient C196(15:8) of DAC miniDSP (DAC Buffer B) REGISTER NAME Reserved. Do not write to this register. 9 0000 0000 Coefficient C196(7:0) of DAC miniDSP (DAC Buffer B) 10 0000 0000 Coefficient C197(15:8) of DAC miniDSP (DAC Buffer B) 11 0000 0000 Coefficient C197(7:0) of DAC miniDSP (DAC Buffer B) 12 0000 0000 Coefficient C198(15:8) of DAC miniDSP (DAC Buffer B) 13 0000 0000 Coefficient C198(7:0) of DAC miniDSP (DAC Buffer B) 14 0000 0000 Coefficient C199(15:8) of DAC miniDSP (DAC Buffer B) 15 0000 0000 Coefficient C199(7:0) of DAC miniDSP (DAC Buffer B) 16 0000 0000 Coefficient C200(15:8) of DAC miniDSP (DAC Buffer B) 17 0000 0000 Coefficient C200(7:0) of DAC miniDSP (DAC Buffer B) 18 0000 0000 Coefficient C201(15:8) of DAC miniDSP (DAC Buffer B) 19 0000 0000 Coefficient C201(7:0) of DAC miniDSP (DAC Buffer B) 20 0000 0000 Coefficient C202(15:8) of DAC miniDSP (DAC Buffer B) 21 0000 0000 Coefficient C202(7:0) of DAC miniDSP (DAC Buffer B) 22 0000 0000 Coefficient C203(15:8) of DAC miniDSP (DAC Buffer B) 23 0000 0000 Coefficient C203(7:0) of DAC miniDSP (DAC Buffer B) 24 0000 0000 Coefficient C204(15:8) of DAC miniDSP (DAC Buffer B) 25 0000 0000 Coefficient C204(7:0) of DAC miniDSP (DAC Buffer B) 26 0000 0000 Coefficient C205(15:8) of DAC miniDSP (DAC Buffer B) 27 0000 0000 Coefficient C205(7:0) of DAC miniDSP (DAC Buffer B) 28 0000 0000 Coefficient C206(15:8) of DAC miniDSP (DAC Buffer B) 29 0000 0000 Coefficient C206(7:0) of DAC miniDSP (DAC Buffer B) 30 0000 0000 Coefficient C207(15:8) of DAC miniDSP (DAC Buffer B) 31 0000 0000 Coefficient C207(7:0) of DAC miniDSP (DAC Buffer B) 32 0000 0000 Coefficient C208(15:8) of DAC miniDSP (DAC Buffer B) 33 0000 0000 Coefficient C208(7:0) of DAC miniDSP (DAC Buffer B) 34 0000 0000 Coefficient C209(15:8) of DAC miniDSP (DAC Buffer B) 35 0000 0000 Coefficient C209(7:0) of DAC miniDSP (DAC Buffer B) 36 0000 0000 Coefficient C210(15:8) of DAC miniDSP (DAC Buffer B) 37 0000 0000 Coefficient C210(7:0) of DAC miniDSP (DAC Buffer B) 38 0000 0000 Coefficient C211(15:8) of DAC miniDSP (DAC Buffer B) 39 0000 0000 Coefficient C211(7:0) of DAC miniDSP (DAC Buffer B) 40 0000 0000 Coefficient C212(15:8) of DAC miniDSP (DAC Buffer B) 41 0000 0000 Coefficient C212(7:0) of DAC miniDSP (DAC Buffer B) 42 0000 0000 Coefficient C213(15:8) of DAC miniDSP (DAC Buffer B) 43 0000 0000 Coefficient C213(7:0) of DAC miniDSP (DAC Buffer B) REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 101 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Table 6-13. Page-15 Registers (continued) 102 REGISTER NUMBER RESET VALUE 44 0000 0000 Coefficient C214(15:8) of DAC miniDSP (DAC Buffer B) 45 0000 0000 Coefficient C214(7:0) of DAC miniDSP (DAC Buffer B) 46 0000 0000 Coefficient C215(15:8) of DAC miniDSP (DAC Buffer B) 47 0000 0000 Coefficient C215(7:0) of DAC miniDSP (DAC Buffer B) 48 0000 0000 Coefficient C216(15:8) of DAC miniDSP (DAC Buffer B) 49 0000 0000 Coefficient C216(7:0) of DAC miniDSP (DAC Buffer B) 50 0000 0000 Coefficient C217(15:8) of DAC miniDSP (DAC Buffer B) 51 0000 0000 Coefficient C217(7:0) of DAC miniDSP (DAC Buffer B) 52 0000 0000 Coefficient C218(15:8) of DAC miniDSP (DAC Buffer B) 53 0000 0000 Coefficient C218(7:0) of DAC miniDSP (DAC Buffer B) 54 0000 0000 Coefficient C219(15:8) of DAC miniDSP (DAC Buffer B) 55 0000 0000 Coefficient C219(7:0) of DAC miniDSP (DAC Buffer B) 56 0000 0000 Coefficient C220(15:8) of DAC miniDSP (DAC Buffer B) 57 0000 0000 Coefficient C220(7:0) of DAC miniDSP (DAC Buffer B) 58 0000 0000 Coefficient C221(15:8) of DAC miniDSP (DAC Buffer B) 59 0000 0000 Coefficient C221(7:0) of DAC miniDSP (DAC Buffer B) 60 0000 0000 Coefficient C222(15:8) of DAC miniDSP (DAC Buffer B) 61 0000 0000 Coefficient C222(7:0) of DAC miniDSP (DAC Buffer B) 62 0000 0000 Coefficient C223(15:8) of DAC miniDSP (DAC Buffer B) 63 0000 0000 Coefficient C223(7:0) of DAC miniDSP (DAC Buffer B) 64 0000 0000 Coefficient C224(15:8) of DAC miniDSP (DAC Buffer B) 65 0000 0000 Coefficient C224(7:0) of DAC miniDSP (DAC Buffer B) 66 0000 0000 Coefficient C225(15:8) of DAC miniDSP (DAC Buffer B) 67 0000 0000 Coefficient C225(7:0) of DAC miniDSP (DAC Buffer B) 68 0000 0000 Coefficient C226(15:8) of DAC miniDSP (DAC Buffer B) 69 0000 0000 Coefficient C226(7:0) of DAC miniDSP (DAC Buffer B) 70 0000 0000 Coefficient C227(15:8) of DAC miniDSP (DAC Buffer B) 71 0000 0000 Coefficient C227(7:0) of DAC miniDSP (DAC Buffer B) 72 0000 0000 Coefficient C228(15:8) of DAC miniDSP (DAC Buffer B) 73 0000 0000 Coefficient C228(7:0) of DAC miniDSP (DAC Buffer B) 74 0000 0000 Coefficient C229(15:8) of DAC miniDSP (DAC Buffer B) 75 0000 0000 Coefficient C229(7:0) of DAC miniDSP (DAC Buffer B) 76 0000 0000 Coefficient C230(15:8) of DAC miniDSP (DAC Buffer B) 77 0000 0000 Coefficient C230(7:0) of DAC miniDSP (DAC Buffer B) 78 0000 0000 Coefficient C231(15:8) of DAC miniDSP (DAC Buffer B) 79 0000 0000 Coefficient C231(7:0) of DAC miniDSP (DAC Buffer B) 80 0000 0000 Coefficient C232(15:8) of DAC miniDSP (DAC Buffer B) 81 0000 0000 Coefficient C232(7:0) of DAC miniDSP (DAC Buffer B) 82 0000 0000 Coefficient C233(15:8) of DAC miniDSP (DAC Buffer B) 83 0000 0000 Coefficient C233(7:0) of DAC miniDSP (DAC Buffer B) 84 0000 0000 Coefficient C234(15:8) of DAC miniDSP (DAC Buffer B) 85 0000 0000 Coefficient C234(7:0) of DAC miniDSP (DAC Buffer B) 86 0000 0000 Coefficient C235(15:8) of DAC miniDSP (DAC Buffer B) 87 0000 0000 Coefficient C235(7:0) of DAC miniDSP (DAC Buffer B) 88 0000 0000 Coefficient C236(15:8) of DAC miniDSP (DAC Buffer B) 89 0000 0000 Coefficient C236(7:0) of DAC miniDSP (DAC Buffer B) 90 0000 0000 Coefficient C237(15:8) of DAC miniDSP (DAC Buffer B) REGISTER NAME REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 Table 6-13. Page-15 Registers (continued) REGISTER NUMBER RESET VALUE 91 0000 0000 Coefficient C237(7:0) of DAC miniDSP (DAC Buffer B) 92 0000 0000 Coefficient C238(15:8) of DAC miniDSP (DAC Buffer B) 93 0000 0000 Coefficient C238(7:0) of DAC miniDSP (DAC Buffer B) 94 0000 0000 Coefficient C239(15:8) of DAC miniDSP (DAC Buffer B) 95 0000 0000 Coefficient C239(7:0) of DAC miniDSP (DAC Buffer B) 96 0000 0000 Coefficient C240(15:8) of DAC miniDSP (DAC Buffer B) 97 0000 0000 Coefficient C240(7:0) of DAC miniDSP (DAC Buffer B) 98 0000 0000 Coefficient C241(15:8) of DAC miniDSP (DAC Buffer B) 99 0000 0000 Coefficient C241(7:0) of DAC miniDSP (DAC Buffer B) 100 0000 0000 Coefficient C242(15:8) of DAC miniDSP (DAC Buffer B) 101 0000 0000 Coefficient C242(7:0) of DAC miniDSP (DAC Buffer B) 102 0000 0000 Coefficient C243(15:8) of DAC miniDSP (DAC Buffer B) 103 0000 0000 Coefficient C243(7:0) of DAC miniDSP (DAC Buffer B) 104 0000 0000 Coefficient C244(15:8) of DAC miniDSP (DAC Buffer B) 105 0000 0000 Coefficient C244(7:0) of DAC miniDSP (DAC Buffer B) 106 0000 0000 Coefficient C245(15:8) of DAC miniDSP (DAC Buffer B) 107 0000 0000 Coefficient C245(7:0) of DAC miniDSP (DAC Buffer B) 108 0000 0000 Coefficient C246(15:8) of DAC miniDSP (DAC Buffer B) 109 0000 0000 Coefficient C246(7:0) of DAC miniDSP (DAC Buffer B) 110 0000 0000 Coefficient C247(15:8) of DAC miniDSP (DAC Buffer B) 111 0000 0000 Coefficient C247(7:0) of DAC miniDSP (DAC Buffer B) 112 0000 0000 Coefficient C248(15:8) of DAC miniDSP (DAC Buffer B) 113 0000 0000 Coefficient C248(7:0) of DAC miniDSP (DAC Buffer B) 114 0000 0000 Coefficient C249(15:8) of DAC miniDSP (DAC Buffer B) 115 0000 0000 Coefficient C249(7:0) of DAC miniDSP (DAC Buffer B) 116 0000 0000 Coefficient C250(15:8) of DAC miniDSP (DAC Buffer B) 117 0000 0000 Coefficient C250(7:0) of DAC miniDSP (DAC Buffer B) 118 0000 0000 Coefficient C251(15:8) of DAC miniDSP (DAC Buffer B) 119 0000 0000 Coefficient C251(7:0) of DAC miniDSP (DAC Buffer B) 120 0000 0000 Coefficient C252(15:8) of DAC miniDSP (DAC Buffer B) 121 0000 0000 Coefficient C252(7:0) of DAC miniDSP (DAC Buffer B) 122 0000 0000 Coefficient C253(15:8) of DAC miniDSP (DAC Buffer B) 123 0000 0000 Coefficient C253(7:0) of DAC miniDSP (DAC Buffer B) 124 0000 0000 Coefficient C254(15:8) of DAC miniDSP (DAC Buffer B) 125 0000 0000 Coefficient C254(7:0) of DAC miniDSP (DAC Buffer B) 126 0000 0000 Coefficient C255(15:8) of DAC miniDSP (DAC Buffer B) 127 0000 0000 Coefficient C255(7:0) of DAC miniDSP (DAC Buffer B) REGISTER NAME 6.13 Control Registers, Page 64: DAC DSP Engine Instruction RAM (0:31) Page 64 / Register 0: Page Control Register BIT D7–D0 READ/ WRITE R/W RESET VALUE 0000 0000 DESCRIPTION 0000 0000: 0000 0001: ... 1111 1110: 1111 1111: Page 0 selected Page 1 selected Page 254 selected Page 255 selected REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 103 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Page 64 / Register 1: Reserved BIT D7–D0 READ/ WRITE R/W RESET VALUE XXXX XXXX READ/ WRITE R/W RESET VALUE XXXX READ/ WRITE R/W RESET VALUE XXXX XXXX READ/ WRITE R/W RESET VALUE XXXX XXXX DESCRIPTION Reserved. Write only the default value to this register Page 64 / Register 2: Inst_0(23:16) BIT D7–D0 DESCRIPTION Instruction Inst_0(23:16) of DAC miniDSP Page 64 / Register 3: Inst_0(15:8) BIT D7–D0 DESCRIPTION Instruction Inst_0(15:8) of DAC miniDSP Page 64 / Register 4: Inst_0(7:0) BIT D7–D0 104 DESCRIPTION Instruction Inst_0(7:0) of DAC miniDSP REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 TLV320DAC3120 www.ti.com SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 6.13.1 Page 64 / Register 5 Through Page 64 / Register 97 The remaining unreserved registers on page 32 are arranged in groups of three, with each group containing the bits of one instruction. The arrangement is the same as that of registers 2–4 for Instruction 0. Registers 5–7, 8–10, 11–13, ..., 95–97 contain instructions 1, 2, 3, ..., 31, respectively. Page 64 / Register 98 Through Page 64 / Register 127: Reserved BIT D7–D0 READ/ WRITE R/W RESET VALUE XXXX XXXX DESCRIPTION Reserved. Write only the default value to this register 6.14 Control Registers, Pages 65–95: DAC DSP Engine Instruction RAM (32:63) Through (992:1023) The structuring of the registers within pages 65–95 is identical to that of page 64. Only the instruction numbers differ. The range of instructions within each page is listed in the following table. Page Instructions 65 32 to 63 66 64 to 95 67 96 to 127 68 128 to 159 69 160 to 191 70 192 to 223 71 224 to 255 72 256 to 287 73 288 to 319 74 320 to 351 75 352 to 383 76 384 to 415 77 416 to 447 78 448 to 479 79 480 to 511 80 512 to 543 81 544 to 575 82 576 to 607 83 608 to 639 84 640 to 671 85 672 to 703 86 704 to 735 87 736 to 767 88 768 to 799 89 800 to 831 90 832 to 863 91 864 to 895 92 896 to 927 93 928 to 959 94 960 to 991 95 992 to 1023 REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 105 TLV320DAC3120 SLAS659A – NOVEMBER 2009 – REVISED MAY 2012 www.ti.com Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Original (November, 2009) to Revision A • • • • • • • • • • • • • • • • • • • 106 Page Added extra bullet point to Features. .......................................................................................... 1 Changed Register 36 to register 35 in section 5.5.2. ...................................................................... 21 Added extra row to the end of Table 5-6. .................................................................................... 23 Added subsection 5.6.1.2.9 and image. ...................................................................................... 25 Added section 5.6.7 from SLAS644C after Interrupts section. .......................................................... 36 Added D6–D0 to the Register Value column heading and changed Analog Attenuation to Analog Gain. ..... 40 Deleted Analog Volume Control for Headphone and Speaker Outputs (for D7=0) table and added table note to D7 = 1 table. .............................................................................................................. 40 Changed page 0 to page 1 in section 5.6.9.1. ............................................................................... 41 Added Timer section and image after PLL section. ....................................................................... 47 Changed last line to "10111-11000: Reserved. Do not use." "11001: DAC Signal Processing Block PRB_P25" "11010-11111: Reserved. Do not use." ......................................................................... 67 Added Beep Generator bit registers from DAC3100 (Page 0 / Register 71, and 73-79). ............................ 70 Added reserved tables. .......................................................................................................... 71 Changed D0=1 to Reserved in Page 1 / Register 33. ...................................................................... 73 Removed extraneous cross-references for deleted table. ................................................................ 74 Added footnote to Page 1 / Register 40: HPOUT Driver. .................................................................. 74 Changed registers 66-127 to Reserved in Table 6-6. ...................................................................... 81 Changed registers 8-13 to Reserved in Table 6-7. ......................................................................... 82 Changed registers 66-127 to Reserved in Table 6-10. ..................................................................... 94 Changed registers 8-13 to Reserved in Table 6-11. ........................................................................ 95 REGISTER MAP Copyright © 2009–2012, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TLV320DAC3120 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) TLV320DAC3120IRHBR ACTIVE VQFN RHB 32 3000 RoHS & Green NIPDAU Level-2-260C-1 YEAR -40 to 85 DAC3120 TLV320DAC3120IRHBT ACTIVE VQFN RHB 32 250 RoHS & Green NIPDAU Level-2-260C-1 YEAR -40 to 85 DAC3120 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
TLV320DAC3120IRHBR 价格&库存

很抱歉,暂时无法提供与“TLV320DAC3120IRHBR”相匹配的价格&库存,您可以联系我们找货

免费人工找货