Product
Folder
Sample &
Buy
Technical
Documents
Support &
Community
Tools &
Software
Reference
Design
TPS54228
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
TPS54228 4.5-V to 18-V Input, 2-A Synchronous Step-Down Converter With Eco-Mode™
1 Features
3 Description
•
The TPS54228 device is an adaptive on-time DCAP2™ mode synchronous buck converter. The
TPS54228 enables system designers to complete the
suite of various end-equipment power bus regulators
with a cost effective, low component count, low
standby current solution. The main control loop for
the TPS54228 uses the D-CAP2™ mode control that
provides a fast transient response with no external
compensation components. The adaptive on-time
control supports seamless transition between PWM
mode at higher load conditions and Eco-Mode™
operation at light loads. Eco-Mode™ allows the
TPS54228 to maintain high efficiency during lighter
load conditions. The TPS54228 also has a proprietary
circuit that enables the device to adopt to both low
equivalent series resistance (ESR) output capacitors,
such as POSCAP or SP-CAP, and ultra-low ESR
ceramic capacitors. The device operates from 4.5-V
to 18-V VIN input. The output voltage can be
programmed between 0.76 V and 7 V. The device
also features an adjustable soft start time. The
TPS54228 is available in 8-pin SO , 8-pin SOIC, and
10-pin VSON packages, and is designed to operate
over the ambient temperature range of –40°C to
85°C.
1
•
•
•
•
•
•
•
•
•
•
•
D-CAP2™ Mode Enables Fast Transient
Response
Low Output Ripple and Allows Ceramic Output
Capacitor
Wide VIN Input Voltage Range: 4.5 V to 18 V
Output Voltage Range: 0.76 V to 7 V
Highly Efficient Integrated FETs Optimized
for Lower Duty Cycle Applications
– 155 mΩ (High-Side) and 108 mΩ (Low-Side)
High Efficiency, Less than 10 µA at Shutdown
High Initial Bandgap Reference Accuracy
Adjustable Soft Start
Prebiased Soft Start
700-kHz Switching Frequency (fSW)
Cycle-by-Cycle Overcurrent Limit
Auto-Skip Eco-Mode™ for High Efficiency at Light
Load
2 Applications
•
Wide Range of Applications for Low Voltage
System
– Digital TV Power Supply
– High Definition Blu-ray Disc™ Players
– Networking Home Terminals
– Digital Set Top Boxes (STB)
Device Information(1)
PART NUMBER
TPS54228
PACKAGE
BODY SIZE (NOM)
HSOP (8)
4.89 mm × 3.90 mm
SOIC (8)
4.89 mm × 3.90 mm
VSON (10)
3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
TPS54228
TPS54228 Transient Response
Vout (50 mV/div)
Iout (1 A/div)
Copyright © 2016, Texas Instruments Incorporated
t - Time - 100 ms
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS54228
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
4
6.1
6.2
6.3
6.4
6.5
6.6
4
4
4
5
5
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 8
7.1
7.2
7.3
7.4
Overview ................................................................... 8
Functional Block Diagram ......................................... 8
Feature Description................................................... 8
Device Functional Modes........................................ 10
8
Application and Implementation ........................ 11
8.1 Application Information............................................ 11
8.2 Typical Application .................................................. 11
9 Power Supply Recommendations...................... 14
10 Layout................................................................... 15
10.1 Layout Guidelines ................................................. 15
10.2 Layout Examples................................................... 15
10.3 Thermal Considerations ........................................ 16
11 Device and Documentation Support ................. 17
11.1
11.2
11.3
11.4
11.5
11.6
Documentation Support ........................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
17
17
17
17
17
17
12 Mechanical, Packaging, and Orderable
Information ........................................................... 17
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (January 2013) to Revision E
Page
•
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section .................................................................................................. 1
•
Deleted Ordering Information table, see POA at the end of the data sheet........................................................................... 3
Changes from Revision C (March 2012) to Revision D
Page
•
Added the 10-pin DRC package to the data sheet ................................................................................................................ 1
•
Added the DRC package to the Device Information section .................................................................................................. 3
•
Added Figure 20 ................................................................................................................................................................... 16
Changes from Revision B (December 2011) to Revision C
•
Removed SWIFT™ from the data sheet title.......................................................................................................................... 1
Changes from Revision A (October 2011) to Revision B
•
2
Page
Added the 8-pin D package to the data sheet ....................................................................................................................... 1
Changes from Original (May 2011) to Revision A
•
Page
Page
Added REN - EN pin resistance to GND to the LOGIC THRESHOLD section of the ELECTRICAL
CHARACTERISTICS table ..................................................................................................................................................... 5
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
TPS54228
www.ti.com
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
5 Pin Configuration and Functions
DDA, D Package
8-Pin HSOP, SOIC
Top View
EN
1
VFB
2
DRC Package
10-Pin VSON
Top View
8
VIN
7
VBST
EN
1
10
VIN
VFB
2
9
VIN
VREG5
3
8
VBST
SS
4
7
SW
GND
5
6
SW
Thermal Pad
VREG5
3
6
SW
SS
4
5
GND
Not to scale
Thermal Pad
Not to scale
Pin Functions
PIN
NAME
I/O
DESCRIPTION
HSOP, SOIC
VSON
EN
1
1
I
Enable input control. EN is active high and must be pulled up to enable the
device.
VFB
2
2
I
Converter feedback input. Connect to output voltage with feedback resistor
divider.
VREG5
3
3
O
5.5-V power supply output. A capacitor (typical 1 µF) must be connected to
GND. VREG5 is not active when EN is low.
SS
4
4
I
Soft-start control. An external capacitor must be connected to GND.
GND
5
—
—
Ground pin. Power ground return for switching circuit. Connect sensitive SS and
VFB returns to GND at a single point.
GND
—
5
—
Ground pin. Connect sensitive SS and VFB returns to GND at a single point.
SW
6
6, 7
O
Switch node connection between high-side NFET and low-side NFET.
VBST
7
8
I
Supply input for the high-side FET gate drive circuit. Connect 0.1µF capacitor
between VBST and SW pins. An internal diode is connected between VREG5
and VBST.
VIN
8
9, 10
I
Input voltage supply pin.
Back side (1)
—
—
Thermal pad of the package. Must be soldered to achieve appropriate
dissipation. Must be connected to GND.
—
Back side
—
Thermal pad of the package. PGND power ground return of internal low-side
FET. Must be soldered to achieve appropriate dissipation.
Exposed
Thermal
Pad
(1)
DDA package only
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
3
TPS54228
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
Input voltage
Output voltage
MIN
MAX
VIN, EN
–0.3
20
VBST
–0.3
26
VBST (transient, 10 ns)
–0.3
28
VBST (vs SW)
–0.3
6.5
VFB, SS
–0.3
6.5
SW
–2
20
SW (transient, 10 ns)
–3
22
VREG5
–0.3
6.5
GND
–0.3
0.3
UNIT
V
V
Voltage from GND to thermal pad, Vdiff
–0.2
0.2
V
Operating junction temperature, TJ
–40
150
°C
Storage temperature, Tstg
–55
150
°C
(1)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
(1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range and VIN = 12 V (unless otherwise noted)
MIN
VIN
VI
Supply input voltage
Input voltage
VBST
–0.1
24
VBST (transient, 10 ns)
–0.1
27
VBST(vs SW)
–0.1
5.7
SS
–0.1
5.7
EN
–0.1
18
VFB
–0.1
5.5
SW
–1.8
18
GND
Output voltage, VREG5
IO
Output current, IVREG5
IOUT
Operating output current (1)
TA
Operating free-air temperature
(1)
4
MAX
18
SW (transient, 10 ns)
VO
NOM
4.5
UNIT
V
V
–3
21
–0.1
0.1
–0.1
5.7
V
0
10
mA
–40
2
A
85
°C
D package, VOUT > 5 V (see Figure 9 for temperature derating)
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
TPS54228
www.ti.com
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
6.4 Thermal Information
TPS54228
THERMAL METRIC (1)
DDA (SO)
D (SOIC)
DRC (VSON)
8 PINS
8 PINS
10 PINS
UNITS
RθJA
Junction-to-ambient thermal resistance
45.3
114.4
43.9
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
54.8
60.8
55.4
°C/W
RθJB
Junction-to-board thermal resistance
16.2
55.7
18.9
°C/W
ψJT
Junction-to-top characterization parameter
6.6
17.4
0.7
°C/W
ψJB
Junction-to-board characterization parameter
16
55.1
19.1
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
8.5
—
5.3
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Electrical Characteristics
over operating free-air temperature range and VIN = 12 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
IVIN
Operating, non-switching supply current
VIN current, TA = 25°C, EN = 5 V,
VFB = 0.8 V
800
1200
µA
IVINSDN
Shutdown supply current
VIN current, TA = 25°C, EN = 0 V
5
10
µA
LOGIC THRESHOLD
VEN
REN
EN high-level input voltage
EN
EN low-level input voltage
EN
EN pin resistance to GND
VEN = 12 V
1.6
220
V
440
0.6
V
880
kΩ
VFB VOLTAGE AND DISCHARGE RESISTANCE
VFBTH
IVFB
VFB threshold voltage
VFB input current
TA = 25°C, VO = 1.05 V, IO = 10 mA,
Eco-Mode™ operation
770
TA = 25°C, VO = 1.05 V,
continuous mode operation
749
VFB = 0.8 V, TA = 25°C
mV
765
781
mV
0
±0.1
µA
5.5
5.7
V
25
mV
100
mV
VREG5 OUTPUT
VVREG5
VREG5 output voltage
TA = 25°C, 6 V < VIN < 18 V,
0 < IVREG5 < 5 mA
VLN5
Line regulation
6 V < VIN < 18 V, IVREG5 = 5 mA
VLD5
Load regulation
0 mA < IVREG5 < 5 mA
IVREG5
Output current
VIN = 6 V, VREG5 = 4 V, TA = 25°C
5.2
60
mA
MOSFET
RDS(on)
High side switch resistance
Low side switch resistance
Iocl
Current limit
DDA and D packages 25°C, VBST – SW = 5.5 V
155
DRC package, 25°C, VBST – SW = 5.5 V
165
25°C
108
DDA and DRC packages, L out = 2.2 µH (1)
D package, L out = 2.2 µH
(1)
2.5
2.3
Shutdown temperature (1)
mΩ
3.3
4.7
A
3
4.5
A
165
TSDN
Thermal shutdown threshold
tON
On time
VIN = 12 V, VO = 1.05 V
150
tOFF(MIN)
Minimum off time
TA = 25°C, VFB = 0.7 V
260
310
ns
Soft-start charge current
VSS = 1 V
1.4
2
2.6
µA
Soft-start discharge current
VSS = 0.5 V
0.1
0.2
Wake up VREG5 voltage
3.45
3.75
4.05
Hysteresis VREG5 voltage
0.13
0.32
0.48
ISS
UVLO
(1)
Undervoltage lockout threshold
Hysteresis (1)
°C
35
ns
mA
V
Not production tested.
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
5
TPS54228
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
www.ti.com
6.6 Typical Characteristics
VIN = 12 V and TA = 25 °C (unless otherwise noted)
14
1000
12
Ivccsdn - Shutdown Current - mA
1200
ICC - Supply Current - mA
SS = 7 V
800
SS = open
600
400
200
10
VIN = 12 V
8
6
4
2
0
-50
0
50
100
TJ - Junction Temperature - °C
0
-50
150
0
Figure 1. VIN Current vs Junction Temperature
50
100
TJ - Junction Temperature - °C
Figure 2. VIN Shutdown Current vs
Junction Temperature
1.1
100
VIN = 18 V
90
VOUT - Output Voltage - V
80
EN - Input Current - mA
150
70
60
50
40
30
VI = 18 V
1.075
VI = 12 V
1.05
VI = 5 V
1.025
20
10
1
0
0
2
4
6
8
10
12
14
EN - Input Voltage - V
16
18
0
20
0.5
1
IOUT - Output Current - A
1.5
2
Figure 4. 1.05-V Output Voltage vs Output Current
Figure 3. EN Current vs EN Voltage
1.07
900
IO = 1 A
IO = 10 mA
fsw - Switching Frequency - kHz
850
VO - Output Voltage - V
1.06
IO = 1 A
1.05
1.04
800
VO = 3.3 V
VO = 2.5 V
VO = 1.8 V
750
VO = 1.5 V
700
650
600
VO = 5 V
VO = 1.05 V
550
VO = 1.2 V
500
450
400
1.03
0
5
10
VI - Input Voltage - V
15
20
Figure 5. 1.05-V Output Voltage vs Input Voltage
6
0
5
10
VI - Input Voltage - V
15
20
Figure 6. Switching Frequency vs Input Voltage
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
TPS54228
www.ti.com
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
Typical Characteristics (continued)
VIN = 12 V and TA = 25 °C (unless otherwise noted)
800
0.780
VO = 1.8 V
VI = 12 V
700
VO = 1.05 V
VFBTH - Vfb Voltage - V
fsw - Switching Frequency - kHz
0.775
600
500
VO = 3.3 V
400
300
0.770
0.765
0.760
200
0.755
100
0
0.01
0.1
1
IO - Output Current - A
10
0.750
-50
Figure 7. Switching Frequency vs Output Current
150
3.0
DDA package
D package
DRC package
2.5
Power Dissipation (W)
2.0
Output Current (A)
50
100
o
TJ - Junction Temperature - C
Figure 8. Vfb Voltage vs Junction Temperature
2.5
1.5
1.0
VOUT = 0.76 to 5 V
VOUT = 6.0 V
VOUT = 7.0 V
0.5
0.0
0
0
20
40
60
Ambient Temperature (°C)
80
2.0
1.5
1.0
0.5
100
0.0
20
G000
Figure 9. D Package Output Current
vs Ambient Temperature
40
60
80
Ambient Temperature (°C)
100
G001
Figure 10. Power Dissipation vs Ambient Temperature
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
7
TPS54228
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
www.ti.com
7 Detailed Description
7.1 Overview
The TPS54228 is a 2-A synchronous step-down (buck) converter with two integrated N-channel MOSFETs. It
operates using D-CAP2™ mode control. The fast transient response of D-CAP2™ control reduces the output
capacitance required to meet a specific level of performance. Proprietary internal circuitry allows the use of lowESR output capacitors including ceramic and special polymer types.
7.2 Functional Block Diagram
EN
EN
1
VIN
Logic
VIN
8
VREG5
Control Logic
Ref
+
SS
+ PWM
7
1 shot
VFB
SW
VO
6
-
2
VBST
XCON
ON
VREG5
VREG5
Ceramic
Capacitor
3
SGND
SS
SS
4
5
Softstart
+
ZC
-
PGND
SGND
SW
GND
PGND
+
OCP
-
SW
PGND
VIN
UVLO
VREG5
UVLO
REF
TSD
Protection
Logic
Ref
Copyright © 2016, Texas Instruments Incorporated
7.3 Feature Description
7.3.1 PWM Operation
The main control loop of the TPS54228 is an adaptive on-time pulse width modulation (PWM) controller that
supports a proprietary D-CAP2™ mode control. D-CAP2™ mode control combines constant on-time control with
an internal compensation circuit for pseudo-fixed frequency and low external component count configuration with
both low ESR and ceramic output capacitors. It is stable even with virtually no ripple at the output.
8
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
TPS54228
www.ti.com
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
Feature Description (continued)
At the beginning of each cycle, the high-side MOSFET is turned on. This MOSFET is turned off after internal
one-shot timer expires. This one shot is set by the converter input voltage, VIN, and the output voltage, VO, to
maintain a pseudo-fixed frequency over the input voltage range, hence it is called adaptive on-time control. The
one-shot timer is reset and the high-side MOSFET is turned on again when the feedback voltage falls below the
reference voltage. An internal ramp is added to reference voltage to simulate output ripple, eliminating the need
for ESR induced output ripple from D-CAP2™ mode control.
7.3.2 PWM Frequency and Adaptive On-Time Control
TPS54228 uses an adaptive on-time control scheme and does not have a dedicated on board oscillator. The
TPS54228 runs with a pseudo-constant frequency of 700 kHz by using the input voltage and output voltage to
set the on-time, one-shot timer. The on-time is inversely proportional to the input voltage and proportional to the
output voltage; therefore, when the duty ratio is VOUT/VIN, the frequency is constant.
7.3.3 Auto-Skip Eco-Mode™ Control
The TPS54228 is designed with Auto-Skip Eco-Mode™ to increase light load efficiency. As the output current
decreases from heavy load condition, the inductor current is also reduced and eventually comes to point that its
rippled valley touches zero level, which is the boundary between continuous conduction and discontinuous
conduction modes. The rectifying MOSFET is turned off when its zero inductor current is detected. As the load
current further decreases the converter run into discontinuous conduction mode. The on-time is kept almost the
same as is was in the continuous conduction mode so that it takes longer time to discharge the output capacitor
with smaller load current to the level of the reference voltage. The transition point to the light load operation
IOUT(LL) current can be calculated in Equation 1
(VIN - VOUT )×VOUT
1
×
I OUT ( LL ) =
2 × L × fsw
VIN
(1)
7.3.4 Soft Start and Prebiased Soft Start
The soft-start function is adjustable. When the EN pin becomes high, 2-µA current begins charging the capacitor
which is connected from the SS pin to GND. Smooth control of the output voltage is maintained during start-up.
The equation for the slow start time is Equation 2. VFB voltage is 0.765 V and SS pin source current is 2 µA.
t
SS
(ms) =
C6(nF) x V
x 1.1 C6(nF) x 0.765 x 1.1
REF
=
I (mA)
2
SS
(2)
The TPS54228 contains a unique circuit to prevent current from being pulled from the output during start-up if the
output is prebiased. When the soft start commands a voltage higher than the prebias level (internal soft start
becomes greater than feedback voltage VFB), the controller slowly activates synchronous rectification by starting
the first low-side FET gate driver pulses with a narrow on-time. It then increments that on-time on a cycle-bycycle basis until it coincides with the time dictated by (1-D), where D is the duty cycle of the converter. This
scheme prevents the initial sinking of the prebias output, and ensure that the out voltage (VO) starts and ramps
up smoothly into regulation and the control loop is given time to transition from prebiased start-up to normal
mode operation.
7.3.5 Current Protection
The output overcurrent protection (OCP) is implemented using a cycle-by-cycle valley detect control circuit. The
switch current is monitored by measuring the low-side FET switch voltage between the SW pin and GND. This
voltage is proportional to the switch current. To improve accuracy, the voltage sensing is temperature
compensated.
During the on-time of the high-side FET switch, the switch current increases at a linear rate determined by VIN,
VOUT, the on-time and the output inductor value. During the on-time of the low-side FET switch, this current
decreases linearly. The average value of the switch current is the load current, IOUT. The TPS54228 constantly
monitors the low-side FET switch voltage, which is proportional to the switch current, during the low-side on-time.
If the measured voltage is above the voltage proportional to the current limit, an internal counter is incremented
per each SW cycle and the converter maintains the low-side switch on until the measured voltage is below the
voltage corresponding to the current limit at which time the switching cycle is terminated and a new switching
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
9
TPS54228
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
www.ti.com
Feature Description (continued)
cycle begins. In subsequent switching cycles, the on-time is set to a fixed value and the current is monitored in
the same manner. If the overcurrent condition exists for 7 consecutive switching cycles, the internal OCL
threshold is set to a lower level, reducing the available output current. When a switching cycle occurs where the
switch current is not above the lower OCL threshold, the counter is reset and the OCL limit is returned to the
higher value.
There are some important considerations for this type of overcurrent protection. The load current one half of the
peak-to-peak inductor current higher than the overcurrent threshold. Also when the current is being limited, the
output voltage tends to fall as the demanded load current may be higher than the current available from the
converter. This may cause the output voltage to fall. When the overcurrent condition is removed, the output
voltage returns to the regulated value. This protection is non-latching.
7.3.6 UVLO Protection
Undervoltage lockout protection (UVLO) monitors the voltage of the VREG5 pin. When the VREG5 voltage is lower
than UVLO threshold voltage, the TPS54228 is shut off. This protection is non-latching.
7.3.7 Thermal Shutdown
TPS54228 monitors the temperature of itself. If the temperature exceeds the threshold value (typically 165°C),
the device is shut off. This is non-latch protection.
7.4 Device Functional Modes
7.4.1 Normal Operation
When the input voltage is above the UVLO threshold and the EN voltage is above the enable threshold, the
TPS54228 can operate in their normal switching modes. Normal continuous conduction mode (CCM) occurs
when the minimum switch current is above 0 A. In CCM, the TPS54228 operates at a quasi-fixed frequency of
700 kHz.
7.4.2 Standby Operation
When the TPS54228 is operating in either normal CCM or forced CCM, it may be placed in standby by asserting
the EN pin low.
10
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
TPS54228
www.ti.com
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The TPS54228 is typically used as step-down converters, which convert a voltage to a lower voltage, 4.5 V to
18 V. WEBENCH™ software is available to aid in the design and analysis of circuits.
8.2 Typical Application
U1
TPS54228
Copyright © 2016, Texas Instruments Incorporated
Figure 11. Example Design Schematic
8.2.1 Design Requirements
Table 1 shows the parameters for this design example.
Table 1. Design Parameters
PARAMETER
VALUE
Input voltage
4.5 V to 18 V
Output voltage
1.05 V
Output current
2A
Output voltage ripple
20 mVpp
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
11
TPS54228
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
www.ti.com
8.2.2 Detailed Design Procedure
8.2.2.1 Output Voltage Resistors Selection
The output voltage is set with a resistor divider from the output node to the VFB pin. TI recommends using 1%
tolerance or better divider resistors. Start by using Equation 3 to calculate VOUT.
To improve efficiency at light loads, consider using larger value resistors. High resistance is more susceptible to
noise, and the voltage errors from the VFB input current are more noticeable.
æ
ö
R1÷
V
= 0.765 x çç1 +
÷
OUT
çè
R2 ÷ø
(3)
8.2.2.2 Output Filter Selection
The output filter used with the TPS54228 is an LC circuit. This LC filter has double pole at:
F =
P
2p L
1
x COUT
OUT
(4)
At low frequencies, the overall loop gain is set by the output set-point resistor divider network and the internal
gain of the TPS54228. The low frequency phase is 180°. At the output filter pole frequency, the gain rolls off at a
–40 dB per decade rate and the phase drops rapidly. D-CAP2™ introduces a high frequency zero that reduces
the gain roll off to –20 dB per decade and increases the phase to 90° one decade above the zero frequency. The
inductor and capacitor selected for the output filter must be selected so that the double pole of Equation 4 is
located below the high frequency zero but close enough that the phase boost provided be the high frequency
zero provides adequate phase margin for a stable circuit. To meet this requirement use the values recommended
in Table 2.
Table 2. Recommended Component Values
OUTPUT VOLTAGE (V)
R1 (kΩ)
R2 (kΩ)
C4 (pF) (1)
L1 (µH)
C8 + C9 (µF)
(1)
1
6.81
22.1
—
1.5 to 2.2
22 to 68
1.05
8.25
22.1
—
1.5 to 2.2
22 to 68
1.2
12.7
22.1
—
2.2
22 to 68
1.5
21.5
22.1
—
2.2
22 to 68
1.8
30.1
22.1
5 to 22
3.3
22 to 68
2.5
49.9
22.1
5 to 22
3.3
22 to 68
3.3
73.2
22.1
5 to 22
3.3
22 to 68
5
124
22.1
5 to 22
4.7
22 to 68
6.5
165
22.1
5 to 22
4.7
22 to 68
Optional
Because the DC gain is dependent on the output voltage, the required inductor value increases as the output
voltage increases. For higher output voltages at or above 1.8 V, additional phase boost can be achieved by
adding a feedforward capacitor (C4) in parallel with R1
The inductor peak-to-peak ripple current, peak current and RMS current are calculated using Equation 5,
Equation 6, and Equation 7. The inductor saturation current rating must be greater than the calculated peak
current, and the RMS or heating current rating must be greater than the calculated RMS current.
Use 700 kHz for fSW. Make sure the chosen inductor is rated for the peak current of Equation 6 and the RMS
current of Equation 7.
- VOUT
V
V
OUT x IN(max)
I
=
IPP
V
L x f
IN(max)
O
SW
I
=I +
Ipeak
O
=
I
Lo(RMS)
12
(5)
I
lpp
2
I
2
O
(6)
+
1
2
I
12 IPP
(7)
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
TPS54228
www.ti.com
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
For this design example, the calculated peak current is 2.311 A and the calculated RMS current is 2.008 A. The
inductor used is a TDK CLF7045T-2R2N with a peak current rating of 5.5 A and an RMS current rating of 4.3 A.
The capacitor value and ESR determines the amount of output voltage ripple. The TPS54228 is intended for use
with ceramic or other low-ESR capacitors. Recommended values range from 22 µF to 68 µF. Use Equation 8 to
determine the required RMS current rating for the output capacitor.
I
Co(RMS)
=
VOUT x (VIN - VOUT )
12 x VIN x LO x fSW
(8)
For this design, two TDK C3216X5R0J226M 22-µF output capacitors are used. The typical ESR is 2 mΩ each.
The calculated RMS current is 0.18 A and each output capacitor is rated for 4 A.
8.2.2.3 Input Capacitor Selection
The TPS54228 requires an input decoupling capacitor and a bulk capacitor is needed depending on the
application. A ceramic capacitor over 10 µF is recommended for the decoupling capacitor. An additional 0.1-µF
capacitor (C3) from pin 8 to ground is optional to provide additional high frequency filtering. The capacitor voltage
rating must be greater than the maximum input voltage.
8.2.2.4 Bootstrap Capacitor Selection
A 0.1-µF ceramic capacitor must be connected between the VBST to SW pin for proper operation. TI
recommends using a ceramic capacitor.
8.2.2.5 VREG5 Capacitor Selection
A 1-µF ceramic capacitor must be connected between the VREG5 to GND pin for proper operation. TI
recommends using a ceramic capacitor.
8.2.3 Application Curves
EN (10 V/div)
Vout (50 mV/div)
VREG5 (5 V/div)
Iout (1 A/div)
Vout (0.5 V/div)
t - Time - 100 ms
t - Time - 1 ms
Figure 12. 1.05-V, Load Transient Response
Figure 13. Start-Up Wave Form
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
13
TPS54228
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
www.ti.com
100
100
VO = 3.3 V
VO = 2.5 V
90
VO = 3.3 V
90
80
VO = 2.5 V
70
VO = 1.8 V
Efficiency - %
Efficiency - %
80
70
60
60
50
VO = 1.8 V
40
30
20
50
10
40
0
0.5
1
IO - Output Current - A
1.5
2
0
0.001
0.01
IO - Output Current - A
0.1
Figure 15. Light Load Efficiency vs Output Current
Figure 14. Efficiency vs Output Current
VO = 1.05 V
Vo (10 mV/div)
VO = 50 mV / div (-950 mV dc offset)
SW = 10 V / div
SW (5 V/div)
Time = 1 µsec / div
t - Time - 400 ns
Figure 16. Voltage Ripple at Output (IO = 2 A)
Figure 17. DCM Voltage Ripple at
Output (IO = 30 mA)
VO = 1.05 V
VIN (50 mV/div)
SW (5 V/div)
t - Time - 400 ns
Figure 18. Voltage Ripple at Input (IO = 2 A)
9 Power Supply Recommendations
The TPS54228 is designed to operate from input supply voltage in the range of 4.5 V to 18 V. Buck converters
require the input voltage to be higher than the output voltage for proper operation. The maximum recommended
operating duty cycle is 65%. Using that criteria, the minimum recommended input voltage is VO / 0.65.
14
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
TPS54228
www.ti.com
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
10 Layout
10.1 Layout Guidelines
1. Keep the input switching current loop as small as possible.
2. Keep the SW node as physically small and short as possible to minimize parasitic capacitance and
inductance and to minimize radiated emissions. Kelvin connections must be brought from the output to the
feedback pin of the device.
3. Keep analog and non-switching components away from switching components.
4. Make a single point connection from the signal ground to power ground.
5. Do not allow switching current to flow under the device.
6. Keep the pattern lines for VIN and PGND broad.
7. Exposed pad of device must be connected to PGND with solder (DDA package only).
8. VREG5 capacitor must be placed near the device, and connected PGND.
9. Output capacitor must be connected to a broad pattern of the PGND.
10. Voltage feedback loop must be as short as possible, and preferably with ground shield.
11. Lower resistor of the voltage divider, which is connected to the VFB pin, must be tied to SGND.
12. Providing sufficient via is preferable for VIN, SW and PGND connection.
13. PCB pattern for VIN, SW, and PGND must be as broad as possible.
14. VIN capacitor mus be placed as near as possible to the device.
10.2 Layout Examples
VIN
FEEDBACK
RESISTORS
TO ENABLE
CONTROL
BIAS
CAP
VIN
INPUT
BYPASS
CAPACITOR
VIN
HIGH FREQENCY
BYPASS
CAPACITOR
EN
VIN
VFB
VBST
VREG5
SW
SS
GND
BOOST
CAPACITOR
SLOW
START
CAP
Connection to
POWER GROUND
on internal or
bottom layer
ANALOG
GROUND
TRACE
EXPOSED
THERMAL PAD
AREA (DDA Package Only)
OUTPUT
INDUCTOR
VOUT
OUTPUT
FILTER
CAPACITOR
POWER GROUND
VIA to Ground Plane
Figure 19. PCB Layout
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
15
TPS54228
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
www.ti.com
Layout Examples (continued)
VIN
FEEDBACK
RESISTORS
TO ENABLE
CONTROL
EN
VIN
HIGH FREQUENCY
BYPASS
VIN CAPACITOR
VFB
VIN
VREG5
BIAS
CAP
SLOW
START
CAP
ANALOG
GROUND
TRACE
VIN
INPUT
BYPASS
CAPACITOR
VBST
SS
SW
GND
SW
BOOST
CAPACITOR
OUTPUT
INDUCTOR
OUTPUT
FILTER
CAPACITOR
EXPOSED
THERMAL PAD
AREA
Connection to
POWER GROUND
on internal or
bottom layer
VOUT
POWER GROUND
VIA to Ground Plane
Figure 20. DRC Package PCB Layout
10.3 Thermal Considerations
This 8-pin DDA package incorporates an exposed thermal pad that is designed to be directly to an external
heartsick. The thermal pad must be soldered directly to the printed-circuit board (PCB). After soldering, the PCB
can be used as a heartsick. In addition, through the use of thermal vias, the thermal pad can be attached directly
to the appropriate copper plane shown in the electrical schematic for the device, or alternatively, can be attached
to a special heartsick structure designed into the PCB. This design optimizes the heat transfer from the
integrated circuit (IC).
For additional information on the exposed thermal pad and how to use the advantage of its heat dissipating
abilities, see PowerPAD™ Thermally Enhanced Package (SLMA002) and PowerPAD™ Made Easy (SMLA004).
Figure 21 shows the exposed thermal pad dimensions for this package.
Figure 21. Thermal Pad Dimensions
16
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
TPS54228
www.ti.com
SLVSAU1E – MAY 2011 – REVISED AUGUST 2016
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation see the following:
• PowerPAD™ Thermally Enhanced Package (SLMA002)
• PowerPAD™ Made Easy (SLMA004)
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
D-CAP2, Eco-Mode, WEBENCH, E2E are trademarks of Texas Instruments.
Blu-ray Disc is a trademark of Blu-ray Disc Association.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Submit Documentation Feedback
Copyright © 2011–2016, Texas Instruments Incorporated
Product Folder Links: TPS54228
17
PACKAGE OPTION ADDENDUM
www.ti.com
1-Mar-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
TPS54228D
ACTIVE
Package Type Package Pins Package
Drawing
Qty
SOIC
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
54228
TPS54228DDA
ACTIVE SO PowerPAD
DDA
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-2-260C-1 YEAR
-40 to 85
54228
TPS54228DDAR
ACTIVE SO PowerPAD
DDA
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU | CU SN
Level-2-260C-1 YEAR
-40 to 85
54228
TPS54228DR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAG
Level-1-260C-UNLIM
-40 to 85
54228
TPS54228DRCR
ACTIVE
VSON
DRC
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
54228
TPS54228DRCT
ACTIVE
VSON
DRC
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
54228
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Mar-2017
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Mar-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TPS54228DDAR
Package Package Pins
Type Drawing
SO
Power
PAD
DDA
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
8
2500
330.0
12.8
6.4
5.2
2.1
8.0
12.0
Q1
TPS54228DR
SOIC
D
8
2500
330.0
12.8
6.4
5.2
2.1
8.0
12.0
Q1
TPS54228DRCR
VSON
DRC
10
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS54228DRCT
VSON
DRC
10
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Mar-2016
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS54228DDAR
SO PowerPAD
DDA
8
2500
366.0
364.0
50.0
TPS54228DR
SOIC
D
8
2500
364.0
364.0
27.0
TPS54228DRCR
VSON
DRC
10
3000
367.0
367.0
35.0
TPS54228DRCT
VSON
DRC
10
250
210.0
185.0
35.0
Pack Materials-Page 2
GENERIC PACKAGE VIEW
DDA 8
PowerPAD TM SOIC - 1.7 mm max height
PLASTIC SMALL OUTLINE
Images above are just a representation of the package family, actual package may vary.
Refer to the product data sheet for package details.
4202561/G
GENERIC PACKAGE VIEW
DRC 10
VSON - 1 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
Images above are just a representation of the package family, actual package may vary.
Refer to the product data sheet for package details.
4204102-3/M
PACKAGE OUTLINE
DRC0010J
VSON - 1 mm max height
SCALE 4.000
PLASTIC SMALL OUTLINE - NO LEAD
3.1
2.9
A
B
PIN 1 INDEX AREA
3.1
2.9
1.0
0.8
C
SEATING PLANE
0.05
0.00
0.08 C
1.65 0.1
2X (0.5)
EXPOSED
THERMAL PAD
(0.2) TYP
4X (0.25)
5
2X
2
6
11
SYMM
2.4 0.1
10
1
8X 0.5
PIN 1 ID
(OPTIONAL)
10X
SYMM
0.5
10X
0.3
0.30
0.18
0.1
0.05
C A B
C
4218878/B 07/2018
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for optimal thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
DRC0010J
VSON - 1 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(1.65)
(0.5)
10X (0.6)
1
10
10X (0.24)
11
(2.4)
SYMM
(3.4)
(0.95)
8X (0.5)
6
5
(R0.05) TYP
( 0.2) VIA
TYP
(0.25)
(0.575)
SYMM
(2.8)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:20X
0.07 MAX
ALL AROUND
0.07 MIN
ALL AROUND
EXPOSED METAL
EXPOSED METAL
SOLDER MASK
OPENING
METAL
METAL UNDER
SOLDER MASK
NON SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK
OPENING
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4218878/B 07/2018
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
DRC0010J
VSON - 1 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
2X (1.5)
(0.5)
SYMM
EXPOSED METAL
TYP
11
10X (0.6)
1
10
(1.53)
10X (0.24)
2X
(1.06)
SYMM
(0.63)
8X (0.5)
6
5
(R0.05) TYP
4X (0.34)
4X (0.25)
(2.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
EXPOSED PAD 11:
80% PRINTED SOLDER COVERAGE BY AREA
SCALE:25X
4218878/B 07/2018
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
