Sample &
Buy
Product
Folder
Technical
Documents
Support &
Community
Tools &
Software
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
TPS566250 4.5-V to 17-V Input, 6-A Synchronous Step-Down Converter With VID Control
1 Features
3 Description
•
The TPS566250 is a synchronous buck converter that
enables system designers to complete the suite of
various end equipment’s power bus regulators with a
cost effective, low component count and low standby
current solution.
1
•
•
•
•
•
•
•
•
•
Integrated FETs Optimized for Lower Duty Cycle
Applications
– 44 mΩ (High Side) and 23 mΩ (Low Side)
Output Voltage Range: 0.6 V to 1.87 V with
5.5-mV Feedback Voltage Step
VID Control with Multibyte Interface with
Read-Back
±1% Output Voltage at 25°C for VID Control at
12 V VIN / 1.1 V VOUT
D-CAP2™ Control Mode
Advanced Eco-mode™ for High Efficiency at Light
Load and Low Output Voltage Ripple
650-kHz Switching Frequency
Fixed Soft Start: 1 ms
Monotonic Pre-Biased Soft Start
Hiccup Timer for Overload Protection
2 Applications
•
•
•
Media Processors for Consumer Applications:
Digital TVs, Set Top Boxes
System On-Chip Power
High Density Power Distribution Systems
After the initial power-up, the output voltage can be
changed by codes sent to the IC via an I2C
compatible VID Control bus.
The main control loops of the TPS566250 use the DCAP2™ mode control which provides a fast transient
response
with
no
external
compensation
components. The adaptive on-time control supports
seamless transition between PWM mode at higher
load conditions and Advanced Eco-mode™ operation
at light loads. Advanced Eco-mode™ allows the
TPS566250 to maintain high efficiency during lighter
load conditions. The TPS566250 is able to adapt to
both low equivalent series resistance (ESR) output
capacitors such as POSCAP or SP-CAP, and ultralow ESR, ceramic capacitors.
The device offers on chip overcurrent, undervoltage
lockout and thermal shutdown protection.
Device Information(1)
PART NUMBER
TPS566250
PACKAGE
HSOP (8)
BODY SIZE (NOM)
4.90 mm x 3.90 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
4 Simplified Schematic
VIN
Load Transient Response
EN
1
2
VOUT
3
SDA
SCL
4
EN
VIN
FB
BOOT
SDA
SCL
SW
GND
8
7
6
VOUT
5
PowerPAD
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Schematic.............................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
4
7.1
7.2
7.3
7.4
7.5
7.6
7.7
4
4
4
4
5
6
7
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information .................................................
Electrical Characteristics...........................................
Timing Requirements ................................................
Typical Characteristics ..............................................
Detailed Description .............................................. 9
8.1
8.2
8.3
8.4
Overview ................................................................... 9
Functional Block Diagram ......................................... 9
Feature Description................................................... 9
Device Functional Modes........................................ 11
8.5 Programming........................................................... 11
8.6 Register Maps ......................................................... 13
9
Applications and Implementation ...................... 16
9.1 Application Information............................................ 16
9.2 Typical Application .................................................. 16
10 Power Supply Recommendations ..................... 23
11 Layout................................................................... 23
11.1 Layout Guidelines ................................................. 23
11.2 Layout Example .................................................... 23
12 Device and Documentation Support ................. 24
12.1
12.2
12.3
12.4
12.5
12.6
Documentation Support .......................................
Third-Party Products Disclaimer ...........................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
24
24
24
24
24
24
13 Mechanical, Packaging, and Orderable
Information ........................................................... 24
13.1 Thermal Information .............................................. 24
5 Revision History
Changes from Revision A (March 2015) to Revision B
•
Page
Added Table 4 ..................................................................................................................................................................... 16
Changes from Original (March 2015) to Revision A
Page
•
Changed the V(FB) MIN value From: –2% to –1.6% in the Electrical Characteristics ............................................................ 5
•
Added Test Condition: "TA = 0°C to 85°C" to V(FB) in the Electrical Characteristics ............................................................. 5
2
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
6 Pin Configuration and Functions
TPS566250
8-Pin DDA
(Top View)
1
EN
VIN
8
2
FB
FB
BOOT
BOOT
7
PowerPAD
3
SDA
SW
SW
6
4
SCL
SCL
GND
GND
5
Pin Functions
PIN
I/O
DESCRIPTION
7
I/O
Supply input for high-side NFET gate drive circuit. Connect 0.1-µF ceramic capacitor between VBST
and SW pins.
EN
1
I
Enable input control. Pull High to enable converter.
FB
2
I
Converter feedback input. Connect to output voltage with resistor divider.
GND
5
–
Power ground
SCL
4
I/O
Clock I/O terminal.
SDA
3
I/O
Data I/O terminal.
SW
6
I/O
Switch node connections for both the high-side NFET and low–side NFET.
VIN
8
I
Input voltage supply pin.
PowerPAD™
–
–
Thermal pad of the package. Must be soldered down to operate normally and achieve appropriate
power dissipation. Connect sensitive FB returns to GND at a single point.
NAME
NO.
BOOT
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
3
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1) (2)
MIN
MAX
UNIT
VIN, EN
–0.3
19
BOOT
–0.3
25
BOOT (10ns transient)
–0.3
27
BOOT (vs SW)
–0.3
6.5
FB, SDA, SCL
–0.3
3.6
–2
19
–3.5
21
Operating Junction temperature, TJ
–40
150
°C
Storage temperature, TSTG
–55
150
°C
Input voltage range
SW
SW (10ns transient)
(1)
(2)
V
These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those
indicated under Recommended Operating Conditions.
All voltages are with respect to IC GND terminal.
7.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
Supply input voltage range
VIN
Input voltage range
TJ
MIN
MAX
4.5
17
BOOT
–0.1
23
BOOT (10 ns transient)
–0.1
26
BOOT (vs SW)
–0.1
6
EN
–0.1
17
FB, SDA, SCL
–0.1
3.3
SW
–1.8
17
SW (10 ns transient)
–3.5
20
–40
150
Operating junction temperature range
UNIT
V
°C
7.4 Thermal Information
THERMAL METRIC (1)
TPS566250
DDA (8)
RθJA
Junction-to-ambient thermal resistance
42.1
RθJCtop
Junction-to-case (top) thermal resistance
55.7
RθJB
Junction-to-board thermal resistance
24.9
ψJT
Junction-to-top characterization parameter
9.5
ψJB
Junction-to-board characterization parameter
24.9
RθJCbot
Junction-to-case (bottom) thermal resistance
3.5
(1)
4
UNIT
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
7.5 Electrical Characteristics
Over operating junction temperature range, VIN = 12 V (Unless otherwise noted)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY VOLTAGE
IIN
VIN supply current
TA = 25°C, EN = 5 V, FB = 0.7 V (non switching)
450
525
µA
I(VINSDN)
VIN shutdown current
TA = 25°C, EN = 0 V
6.5
10
µA
1.1
1.6
V
LOGIC THRESHOLD
V(ENH)
EN H-level threshold voltage
V(ENL)
EN L-level threshold voltage
0.6
Hystersis
R(EN)
EN pin resistance to GND
V(EN) = 12 V
0.94
V
160
mV
225
350
800
–1.6%
0
1.6%
kΩ
FEEDBACK VOLTAGE
TA = 0°C to 85°C
VOUT = 1.1 V, Upper/lower feedback resistors:
1.37 kΩ / 1.65 kΩ
V(FB)
FB voltage
TA = 25°C, VOUT = 1.1 V, IOUT = 10 mA, pulse
skipping
TA = 25°C, VOUT = 1.1 V, continuous current mode
0.606
0.594
V
0.6
0.606
V
MOSFET
rDS(on)H
High side switch resistance
BOOT - SW = 5.5 V
44
74
mΩ
rDS(on)L
Low side switch resistance
VIN = 12 V
23
35
mΩ
Discharge FET
200
Ω
650
kHz
ON-TIME TIMER CONTROL
fsw
Switching frequency
LOUT = 1.5 µH, COUT = 22 µF x 2, VOUT = 1.1 V
CURRENT LIMIT
IOCL
Valley current limit
LOUT = 1.5 µH, VOUT = 1.1 V, VIN = 12 V
7.6
9.5
11.4
A
Reverse valley current limit
LOUT = 1.5 µH, VOUT = 1.1 V
1.5
4.5
7
A
OUTPUT UNDERVOLTAGE PROTECTION
V(UVP)
Output UVP trip threshold
UVP detect (H > L)
65%
THERMAL SHUTDOWN
TSDN
Thermal shutdown Threshold
Shutdown temperature (1)
Hysteresis (1)
165
°C
15
°C
UVLO
UVLO
UVLO Threshold
VIN rising voltage
3.26
3.75
4.05
V
Hysteresis VIN voltage
0.13
0.33
0.48
V
0.6
V
2
PGOOD VIA I C
FB falling (fault) VO = 1.1 V
V(PGOODTH)
PGOOD threshold
SERIAL INTERFACE (1)
80%
FB rising (good) VO = 1.1 V
85%
FB rising (fault) VO = 1.1 V
125%
FB falling (good) VO = 1.1 V
120%
(2) (3)
VIL
LOW level input voltage
VIH
HIGH level input voltage
1.85
V
Vhys
Hysteresis of schmitt trigger inputs
0.11
V
VOL
LOW level output voltage
(Open drain, 3 mA sink current)
0.4
V
fSCL
SCL clock frequency
400
kHz
Cb
Capacitive load for each bus line
400
pF
(1)
(2)
(3)
Specified by design. Not production tested.
Refer to Figure 1 for I2C Timing Definitions
Cb = capacitance of bus line in pF
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
5
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
www.ti.com
7.6 Timing Requirements
MIN
TYP
MAX
UNIT
ON-TIME TIMER CONTROL
ton
SW On time
VIN = 12 V, VOUT = 1.1 V
165
toff
SW Minimum off time
TA = 25 °C, FB = 0.5 V
275
325
ns
ns
1
1.3
ms
SOFT START
tSS
Soft start time
Internal soft start time
0.7
OUTPUT UNDERVOLTAGE PROTECTION
t(UVPDEL)
Hiccup delay time (power into short)
1.3
ms
t(UVPEN)
Hiccup off time before restart
10
ms
SERIAL INTERFACE (1)
(2) (3)
t(SP)
Pulse width of spikes suppressed by input
filter
32
ns
t(HD;STA)
Hold time (repeated) START condition.
0.6
µs
tLOW
LOW period of SCL clock
1.3
µs
tHIGH
HIGH period of SCL clock
0.6
µs
t(SU;STA)
Set-up time for a repeated START condition
0.6
t(HD;DAT)
Data Hold time
50
t(SU;DAT)
Data set-up time
tr
Rise time (SDA or SCL)
20+0.1Cb (3)
300
ns
tf
Fall time (SDA or SCL)
20+0.1Cb (3)
300
ns
t(SU;STO)
Set-up time for STOP condition
0.6
µs
t(BUF)
Bus free time between STOP and START
condition
1.3
µs
(1)
(2)
(3)
µs
900
100
ns
ns
Specified by design. Not production tested.
Refer to Figure 1 below for I2C Timing Definitions
Cb = capacitance of bus line in pF
VIH
VIL
Figure 1. I2C Timing Definitions (reproduced from Phillips I2C spec Version 1.1)
6
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
7.7 Typical Characteristics
60
600
50
500
Supply Current (PA)
Enable Pin Current (uA)
VIN = 12 V, TA = 25 °C, unless otherwise specified.
40
30
20
400
300
200
100
10
0
-50
0
0
5
10
Enable Pin Voltage (V)
15
20
0
25
50
75
100
Junction Temperature (qC)
125
150
D007
Figure 3. Supply Current vs Junction Temperature
7
710
6
700
Switching Frequency (kHz)
Shutdown Current (uA)
Figure 2. Enable Current vs Enable Voltage
5
4
3
2
690
680
670
660
650
1
640
0
-50
-25
0
25
50
75
100
Junction Temperature (qC)
125
0
150
5
D006
Figure 4. Shutdown Current vs Junction Temperature
0.604
1000
0.602
800
0.600
600
400
200
10
Input Voltage (V)
15
20
D009
Figure 5. Switching Frequency vs Input Voltage
1200
FB Voltage (V)
Switching Frequency (kHz)
-25
D010
0.598
0.596
0.594
0
0
1
2
3
4
Output Current (A)
5
6
7
0.592
-50
D008
Figure 6. Switching Frequency vs Output Current
-25
0
25
50
75
100
Junction Temperature (qC)
125
150
D005
Figure 7. Feedback Voltage vs Junction Temperature
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
7
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
www.ti.com
Typical Characteristics (continued)
VIN = 12 V, TA = 25 °C, unless otherwise specified.
80
1.13
70
HS, LS On Resistance (m:)
1.15
1.11
SS time (ms)
1.09
1.07
1.05
1.03
1.01
0.99
60
50
40
30
20
10
0.97
0.95
-50
-25
0
25
50
75
100
Junction Temperature (qC)
125
0
-50
150
0
25
50
75
100
Junction Temperature (qC)
125
150
D003
Figure 9. HS and LS rDS(on) vs Junction Temperature
10.0
3.80
9.9
3.75
9.8
3.70
9.7
Current Limit (A)
3.85
3.65
Rising
Falling
3.60
-25
D009
D001
Figure 8. Soft Start Time vs Junction Temperature
VIN UVLO (V)
RHS
RLS
3.55
3.50
3.45
9.6
9.5
9.4
9.3
9.2
3.40
9.1
3.35
-50
9.0
-50
-25
0
25
50
75
100
Junction Temperature (qC)
125
150
-25
0
D002
Figure 10. Input Voltage UVLO vs Junction Temperature
25
50
75
100
Junction Temperature (qC)
125
150
D004
Figure 11. Current Limit vs Junction Temperature
9.6
9.5
Current Limit (A)
9.4
9.3
9.2
9.1
9.0
8.9
8.8
8.7
8.6
0
5
10
Input Voltage (V)
15
20
D003
Figure 12. Current Limit vs Input Voltage
8
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
8 Detailed Description
8.1 Overview
The TPS566250 is a synchronous step-down (buck) converter with two integrated N-channel MOSFETs for each
channel. It operates using D-CAP2™ control mode. The fast transient response of D-CAP2™ control reduces the
required output capacitance required to meet a specific level of performance. The output voltage of the device
can be set by either FB with divider resistors and I2C compatible interface.
8.2 Functional Block Diagram
VREG5
EN
EN
1
Logic
VREG5
UVLO
EN
VREG5
+
UV
EN
-35%
8
VIN
7
BOOT
6
SW
VREG5
Control Logic
FB
-
2
+ PWM
1 shot
+
XCON
ON
Soft
Start
VREG5
GND
DAC
5
3
SCL
4
Serial
Interface
EN
+
OCP
-
SW
VALLEY CURRENT LIMIT
PG_OV
Chip ADDR
0110001
UV
UVLO
Protection
Logic
PWM
COMPARATOR
INPUT
PowerPAD
PGOOD
-
OCP
SDA
PGND
+
7 bits
SW
-
+
ZC
-
VREF
TSD
+
PG_UV
8.3 Feature Description
8.3.1 PWM Operation
The main control loop of the TPS566250 is an adaptive on-time pulse width modulation (PWM) controller that
supports a proprietary D-CAP2™ mode control. D-CAP2™ control combines constant on-time control with an
internal compensation circuit for pseudo-fixed frequency and low external component count configuration with
both low ESR and ceramic output capacitors. It is stable even with virtually no ripple at the output.
At the beginning of each cycle, the high-side MOSFET is turned on. This MOSFET is turned off when the internal
timer expires. This timer is set by the converter’s input voltage, VIN, and the output voltage, VOUT, to maintain a
pseudo-fixed frequency over the input voltage range hence it is called adaptive on-time control. The timer is reset
and the high-side MOSFET is turned on again when the feedback voltage falls below the nominal output voltage.
An internal ramp is added to the reference voltage to simulate output voltage ripple, eliminating the need for ESR
induced output ripple from D-CAP2™ mode control.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
9
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
www.ti.com
Feature Description (continued)
8.3.2 PWM Frequency and Adaptive On-Time Control
TPS566250 uses an adaptive on-time control scheme and does not have a dedicated on board oscillator. The
device runs with a pseudo-constant frequency of 650 kHz by using the input voltage and output voltage to set the
on-time timer. The on-time is inversely proportional to the input voltage and proportional to the output voltage,
therefore, when the duty ratio is VOUT/VIN, the switching frequency is constant.
8.3.3 Soft Start and Pre-Biased Soft Start
The TPS566250 has an internal 1 ms soft-start. When the EN pin becomes high, internal soft-start function
begins ramping up the reference voltage to the PWM comparator. The device contains a unique circuit to prevent
sinking current from the output during startup if the output is pre-biased. When the soft-start commands a voltage
higher than the pre-bias level (internal soft start becomes greater than feedback voltage FB), the controller slowly
activates synchronous rectification by starting the first low side FET gate driver pulses with a narrow on-time. It
then increments that on-time on a cycle-by-cycle basis until it coincides with the time dictated by (1-D), where D
is the duty cycle of the converter. This scheme prevents the initial sinking of the pre-bias output, and ensure that
the out voltage (VOUT) starts and ramps up smoothly into regulation and the control loop is given time to transition
from output pre-biased startup to normal mode operation.
8.3.4 Overcurrent Protection
The output overcurrent protection (OCP) is implemented using a cycle-by-cycle valley detect control circuit. The
switch current is monitored by measuring the low-side FET switch voltage between the SW pin and GND. This
voltage is proportional to the switch current. To improve accuracy, the voltage sensing is temperature
compensated.
During the on time of the high-side FET switch, the switch current increases at a linear rate determined by VIN,
VOUT, the on-time and the output inductor value. During the on time of the low-side FET switch, this current
decreases linearly. The average value of the switch current is the load current IOUT. The device constantly
monitors the low-side FET switch voltage, which is proportional to the switch current, during the low-side on-time.
If the measured voltage is above the voltage proportional to the current limit, the converter maintains the low-side
switch on until the measured voltage is below the voltage corresponding to the current limit at which time the
switching cycle is terminated and a new switching cycle begins. In subsequent switching cycles, the on-time is
set to a fixed value and the current is monitored in the same manner. If the overcurrent condition exists for 7
consecutive switching cycles, the internal OCL threshold is set to a lower level, reducing the available output
current. When a switching cycle occurs where the switch current is not above the lower OCL threshold, the
counter is reset and the OCL limit is returned to the higher value.
There are some important considerations for valley overcurrent protection. The average load current is half the
peak-to-peak inductor current plus the valley overcurrent threshold during current limit. The output voltage falls
as the demanded load current exceeds the current limit. When the FB voltage becomes lower than 65% of the
target voltage, the UVP comparator detects it and the Hiccup sequence is initiated. After 10 µs detecting the UVP
voltage, device shuts down and re-starts after the hiccup time.
When the over current condition is removed, the output voltage returns to the regulated value.
8.3.5 UVLO Protection
Undervoltage lock out protection (UVLO) monitors the voltage of the VIN terminal. When the VIN voltage is lower
than UVLO threshold voltage, the device is shut off. This protection is non-latching.
8.3.6 Thermal Shutdown
TPS566250 monitors the temperature of itself. If the temperature exceeds the threshold value (typically 165°C),
the device is shut off. This is non-latch protection.
10
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
8.4 Device Functional Modes
8.4.1 Auto-Skip Eco-mode™ Control
The TPS566250 is designed with Advanced Eco-mode™ to increase light load efficiency. As the output current
decreases from heavy load condition, the inductor current is also reduced and eventually comes to the where its
ripple valley touches the zero level, which is the boundary between continuous conduction and discontinuous
conduction modes. The rectifying MOSFET is turned off when its zero inductor current is detected. As the load
current further decreases the converter run into discontinuous conduction mode. The on-time is lowered to
reduce the output voltage ripple. The transition point to the light load operation IO(LL) current can be estimated
with Equation 1 with 650 kHz used as fSW.
(VIN - VO ) ´ VO
1
IO(LL) =
+ 0.5 A
´
2 ´ LO ´ fSW
VIN
(1)
8.5 Programming
8.5.1 I2C Interface
The TPS566250 implements a subset of the Phillips I2C specification Ver. 1.1. The TPS566250 is a Slave-Only
(it never becomes a Master, and so never pulls down the SCL pin on the I2C bus). An I2C transaction consists of
either writing a data byte to one of the device internal registers which requires a 3-byte transaction or reading
back one byte from a register which requires a 4-byte transaction. The protocols follow the System Management
Bus (SMBUS) Specification Ver. 2.0 Write Byte and Read Byte protocols. This spec is available on the Internet
for further reading, but the subset implemented in TPS566250 is described as:
• Long-form address modes, multi-byte data transfers and Packet Error Code (PEC) protocols are not
supported in this implementation, though a unique to the TPS566250.
• The I2C interface pins are composed of the SDA (Data) and SCL (Clock) pins. SDA and SCL are designed to
be used with pullup resistors to 3.3 V.
8.5.2 I2C Protocol
8.5.2.1 Input Voltage
Logic levels for I2C SDA and SCL pins are not fixed. For the TPS566250, a logic “0” (LOW) should be 0 V and a
logic “1” (HIGH) can be any voltage between 2.5 V and 3.3 V. Logic HIGH is generated by external pullup
resistors (see Output Voltage).
8.5.2.2 Output Voltage
the I2C bus has external pullup resistors, one for SCL and one for SDA. These pull up to a voltage called VDD
which must lie between 2.5 V and 3.3 V. The outputs are pulled down to their logic LOW levels by open-drain
outputs and pulled up to their logic HIGH levels by these external pullups. The pullups must be selected so that
the current into any chip when pulled LOW by that chip’s open drain output (=VDD/RPULLUP) is less than 3 mA.
8.5.2.3 Data Format
One clock pulse on the SCL clock line is generated for each bit of data to be transferred. The data on the SDA
line must be stable during the HIGH period of the SCL clock line. The HIGH or LOW state of the data line can
only change when the clock signal on the SCL line is LOW.
8.5.2.4 START and STOP Conditions
A HIGH to LOW transition on the SDA line while the SCL line is HIGH defines a START condition. A LOW to
HIGH transition on the SDA line while the SCL line is HIGH defines a STOP condition. START and STOP
conditions are always generated by the Master. The bus is considered to be BUSY after the condition. It is
considered to be free again after a minimum of 4.7 µS after the STOP condition.
The bus stays busy if a repeated START (Sr) is generated instead of a STOP condition. START and repeated
START are functionally identical.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
11
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
www.ti.com
Programming (continued)
Every byte of data out on the SDA line is 8 bits long. 9 clocks occur for each byte (the additional clock being for
an ACK signal put onto the bus by the device pulling down on the bus to acknowledge receipt of the data). In the
Figure 13 and Figure 14, shaded blocks indicate SDA data generated by the device being sent to the Master I2C
controller, while white blocks indicate SDA data generated by the Master being received by the device. The
Master always generates the SCL signal.
Sending data to the TPS566250 is accomplished using the following 3-byte sequence, referred to as a Write Byte
transaction:
S
SDA
Chip Address
Wr
A 6 A 5 A 4 A 3 A 2 A1 A0
A
Register Address
A
Data Byte
A
P
0 ACK R7 R6 R5 R4 R3 R2 R1 R0 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK
SCL
Stop Condition
Start Condition
Figure 13. A Complete Write Byte Transfer, Adapted From SMBUS Spec
Reading back data from the TPS566250 is accomplished using the following 4-byte sequence, referred to as a
Read Byte transaction:
S
SDA
Chip Address
Wr
A 6 A 5 A 4 A 3 A 2 A1 A0
A
Register Address
A Sr
0 ACK R7 R6 R5 R4 R3 R2 R1 R0 ACK
Chip Address
A6 A5 A4 A3 A2 A1 A0
Rd
A
Data Byte
A
P
1 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK
SCL
Start Condition
Stop Condition
Repeated Start
Figure 14. A Complete Read Byte Transfer, Adapted From SMBUS Spec
On the TPS566250, the I2C bus is inactive until:
1. Both SDA and SCL have been at a logic high simultaneously to prevent power sequencing issues.
2. VOUT is in regulation.
Control registers can be written after soft start is complete (1.7 times soft start time).
Until a VOUT command has been accepted, the device output voltage is determined by the external resistor
divider feedback to the FB pin, the initial FB voltage (typically 0.6 V), and the condition of the EN pin.
When the device receives a Chip Address code it recognizes to be its own, it responds by sending an ACK
(pulling down on the SDA bus during the next clock on the SCL bus). If the address is not recognized, the device
assumes that the I2C message is intended for another chip on the bus, and it takes no action. It disregards data
sent thereafter until the next START is begun.
If, after recognizing its Chip Address, the TPS566250 receives a valid Register Address, it sends an ACK and
prepare to receive a Data Byte to be sent to that Register.
If a valid Data Byte is then received, it sends an ACK and sets the output voltage to the desired value. It is
recommended to readback to verify the output voltage code. When sending data to the Output Voltage register,
the output voltage only changes upon receipt of a valid data byte.
8.5.3 I2C Chip Address Byte
The 7-bit address of the TPS566250 is set at 31h in hex notation (0110001 in binary notation) internally. When
the Master is sending the address as an 8-bit value, the 7-bit address should be sent followed by a trailing 0 to
indicate this is a WRITE operation.
12
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
8.6 Register Maps
8.6.1 I2C Register Address Byte
The TPS566250 contains 2 customer-accessible registers. Register 0d (0h) is the output voltage register.
Register 24d (18h) is the power good register
8.6.1.1 Output Voltage Register (offset = 00000000) [reset = 0h]
Register 0d (0h) is the Output Voltage resister.
Figure 15. Output Voltage Register
7
Odd Parity
R/W
6
5
4
3
VOUT
R/W
2
1
0
2
1
0
PGOOD
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 1. Output Voltage Register
Bit
7
6:0
Field
Type
Reset
Description
Odd Parity
R/W
0h
See CheckSum Bit
VOUT
R/W
0h
See Table 3
8.6.1.2 Power Good State Register (offset = 00011000) [reset = 18h]
Register 24d (18h) provides the power good state
Figure 16. Power Good State Register
7
6
5
4
TI only
R
3
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 2. Power Good Register
Bit
Field
Type
Reset
Description
7:1
TI only
R
0h
TI only
PGOOD
R
18h
1 = FB voltage within PGOOD threshold limits
0 = FB Voltage outside PGOOD threshold limits
0
8.6.2 CheckSum Bit
The CheckSum bit should be set by the Master controller to be the exclusive-OR of the D[6:0] bits (odd parity).
This is used by the TPS566250 to check that a valid data byte was received. If CheckSum is not equal to the
exclusive-OR of these bits, the TPS566250 assumes that an error occurred during the data transmission, nor
does not reset the VOUT to the received code (or, if the Control register does not reset the register contents as
requested). The Master should try again to send the data.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
13
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
www.ti.com
8.6.3 Output Voltage Registers
The lower 7 bits of the Output Voltage Register controls the VOUT of the device. These bits are the 7-bit selector
for one of the output voltages. The default output voltage is 1.1 V, that is 50d (32h)
When the IC powers up, the startup and output voltage regulation conditions are set by the external resistor
divider feedback to the FB pin, the initial FB voltage and the condition of the EN pin. Bringing the EN pin high
begins a soft-start ramp on the regulator.
After applying VIN, VOUT comes into regulation and the I2C interface actives.
By default, the device regulates VOUT using the external feedback resistors connected to the FB pin and the initial
FB voltage. The user can then program VOUT by writing any VOUT code.
Table 3. Ideal VOUT vs VOUT [6:0] Code
(Upper/lower Feedback Resistors: 1.37 kΩ / 1.65 kΩ
(1)
(2)
Code
Binary
VOUT
Code
Binary
VOUT
Code
Binary
VOUT
Code
Binary
VOUT
0
0000000
0.60
32
0100000
0.92
64
1000000
1.24
96
1100000
1.56
1
0000001
0.61
33
0100001
0.93
65
1000001
1.25
97
1100001
1.57
2
0000010
0.62
34
0100010
0.94
66
1000010
1.26
98
1100010
1.58
3
0000011
0.63
35
0100011
0.95
67
1000011
1.27
99
1100011
1.59
4
0000100
0.64
36
0100100
0.96
68
1000100
1.28
100
1100100
1.60
5
0000101
0.65
37
0100101
0.97
69
1000101
1.29
101
1100101
1.61
6
0000110
0.66
38
0100110
0.98
70
1000110
1.30
102
1100110
1.62
7
0000111
0.67
39
0100111
0.99
71
1000111
1.31
103
1100111
1.63
8
0001000
0.68
40
0101000
1.00
72
1001000
1.32
104
1101000
1.64
9
0001001
0.69
41
0101001
1.01
73
1001001
1.33
105
1101001
1.65
10
0001010
0.70
42
0101010
1.02
74
1001010
1.34
106
1101010
1.66
11
0001011
0.71
43
0101011
1.03
75
1001011
1.35
107
1101011
1.67
12
0001100
0.72
44
0101100
1.04
76
1001100
1.36
108
1101100
1.68
13
0001101
0.73
45
0101101
1.05
77
1001101
1.37
109
1101101
1.69
14
0001110
0.74
46
0101110
1.06
78
1001110
1.38
110
1101110
1.70
15
0001111
0.75
47
0101111
1.07
79
1001111
1.39
111
1101111
1.71
16
0010000
0.76
48
0110000
1.08
80
1010000
1.40
112
1110000
1.72
17
0010001
0.77
49
0110001
1.09
81
1010001
1.41
113
1110001
1.73
18
0010010
0.78
50
0110010
1.10
82
1010010
1.42
114
1110010
1.74
19
0010011
0.79
51
0110011
1.11
83
1010011
1.43
115
1110011
1.75
20
0010100
0.80
52
0110100
1.12
84
1010100
1.44
116
1110100
1.76
21
0010101
0.81
53
0110101
1.13
85
1010101
1.45
117
1110101
1.77
22
0010110
0.82
54
0110110
1.14
86
1010110
1.46
118
1110110
1.78
23
0010111
0.83
55
0110111
1.15
87
1010111
1.47
119
1110111
1.79
24
0011000
0.84
56
0111000
1.16
88
1011000
1.48
120
1111000
1.80
25
0011001
0.85
57
0111001
1.17
89
1011001
1.49
121
1111001
1.81
26
0011010
0.86
58
0111010
1.18
90
1011010
1.50
122
1111010
1.82
27
0011011
0.87
59
0111011
1.19
91
1011011
1.51
123
1111011
1.83
28
0011100
0.88
60
0111100
1.20
92
1011100
1.52
124
1111100
1.84
29
0011101
0.89
61
0111101
1.21
93
1011101
1.53
125
1111101
1.85
30
0011110
0.90
62
0111110
1.22
94
1011110
1.54
126
1111110
1.86
31
0011111
0.91
63
0111111
1.23
95
1011111
1.55
127
1111111
1.87
10-mV output voltage steps can be applied to 1.1-V output voltage setting only.
For other default voltage setting, the output voltage step are shown in Equation 2.
Output Voltage Step = 10 x Target Output Voltage/1.1 mV
14
(1) (2)
Submit Documentation Feedback
(2)
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
8.6.4 Summary of Default Control Bits
8.6.4.1 DAC Settle
When a new VOUT voltage is selected, this happens by setting an internal DAC to a new internal VREF voltage. If
this happens instantly, the regulator loop is thrown out of regulation and the DCAP2 loop must respond to bring
the VOUT back into regulation at its new chosen value. To reduce VOUT overshoots (or undershoots) or high
transient input currents due to the internal VREF change, There is an analog filter on the DAC output. The filter is
set at 20 µs constant.
8.6.4.2 Operation During VID Transition
The device temporarily goes into forced CCM mode during VID transitions for approximately 100 µs. This helps
discharge VOUT during a step down when there is a light load present. The Power Good is masked for
approximately 100 µs to prevent a power good flag during the transition.
CONTROL BIT(S)
DEFAULT
FUNCTION
VOUT[7:0]
0110010
(32h)
VOUT code, 7 bits VOUT[6:0] + odd parity checksum bit at VOUT[7].
Writing a valid code to this register also sets VID Mode. Sending an invalid code
(checksum incorrect) to this register does not change register contents or set
Internal/Enable bits.
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
15
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
www.ti.com
9 Applications and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The devices are synchronous step down DC-DC converters rated at different output currents whose output
voltage can be dynamically scaled by sending commands over an I2C interface. This section discusses the
design of the external components to complete the power supply design by using a typical application as a
reference.
9.2 Typical Application
VIN
4.5V to 17V
VIN
C1
10PF
C3
0.1PF
C2
10PF
EN
VOUT
R1
1.37 k:
C4
(option)
R2
1.65k:
1
2
3
VDD
Rp2
4
Rp1
EN
VIN
FB
BOOT
SDA
SW
SCL
GND
8
7
C5 0.1PF
L1 1.5PH
VOUT
1.1V 6A
6
VOUT
5
C6
22PF
PowerPAD
C7
22PF
SDA
SCL
Figure 17. Typical Application Schematic
Table 4. Components
REFERENCE DESIGNATOR
16
PART NUMBER
MANUFACTURER
L1
744 314 150
Wurth Electronics
C6 , C7
C1210C226K9RACTU
Kemet
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
9.2.1 Design Requirements
For this design example, use the parameters shown in Table 5.
Table 5. Design Example
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage
12 V
Output voltage
1.1 V
Transient response, 0 A – 6 A load step
ΔVOUT = ±5%
Output voltage ripple
25 mV
Input ripple voltage
400 mV
Output current rating
6A
Operating Frequency
650 kHz
9.2.2 Detailed Design Procedure
9.2.2.1 Output Voltage Resistors Selection
The output voltage is set with a resistor divider from the output node to the FB pin. It is recommended to use 1%
tolerance or better divider resistors. Use 1.37 kΩ for R1 and 1.65 kΩ for R2.
R2
V(FB) = VO ´
(3)
R1 + R2
9.2.2.2 Output Filter Selection
The output filter used with the TPS566250 is an LC circuit. This LC filter has double pole at:
1
FP =
2p LO ´ CO
(4)
At low frequencies, the overall loop gain is set by the output set-point resistor divider network and the internal
gain of the device. The low frequency phase is 180 degrees. At the output filter pole frequency, the gain rolls off
at a –40 dB per decade rate and the phase drops rapidly. D-CAP2™ introduces a high frequency zero that
reduces the gain roll off to –20 dB per decade and increases the phase to 90 degrees one decade above the
zero frequency. The inductor and capacitor selected for the output filter must be selected so that the double pole
of Equation 4 is located below the high frequency zero but close enough that the phase boost provided be the
high frequency zero provides adequate phase margin for a stable circuit. To meet this requirement use the
values recommended in Table 6.
Table 6. Recommended Component Values
Output
Voltage (V)
R1 (kΩ)
R2 (kΩ)
C4 (pF) (1)
MIN
TYP
L1 (µH)
MAX
MIN
TYP
MAX
C67 (µF)
1
1.37
1.65
1.5
22 - 68
1.1 (Default)
1.37
1.65
1.5
22 - 68
1.2
1.37
1.65
1.5
22 - 68
1.5
1.37
1.65
1.5
22 - 68
1.8
1.37
1.65
1.5
22 - 68
(1)
Optional
The inductor peak-to-peak ripple current, peak current and RMS current are calculated using Equation 5,
Equation 6 and Equation 7. The inductor saturation current rating must be greater than the calculated peak
current and the RMS or heating current rating must be greater than the calculated RMS current. For the
calculations, use 500 kHz as the switching frequency, fSW. Make sure the chosen inductor is rated for the peak
current of Equation 6 and the RMS current of Equation 7.
VIN(MAX) - VO
VO
DILO =
´
VIN(MAX)
LO ´ fSW
(5)
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
17
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
ILPEAK = IO +
www.ti.com
DIL
2
ILO(RMS) = IO2 +
(6)
1
DIL 2
12
(7)
The capacitor value and ESR determines the amount of output voltage ripple. The TPS566250 is intended for
use with ceramic or other low ESR capacitors. Recommended values range from 22 µF to 68 µF.
9.2.2.3 Input Capacitor Selection
The TPS566250 requires an input decoupling capacitor and a bulk capacitor depending on the application. A
ceramic capacitor of 10 µF or above is recommended for the decoupling capacitor. Additionally, a 0.1-µF ceramic
capacitor from VIN to GND is also recommended to improve the stability and reduce the SW node overshoots.
The capacitors voltage rating needs to be greater than the maximum input voltage.
9.2.2.4 Bootstrap Capacitor Selection
The 0.1-µF ceramic capacitors must be connected between the BOOT to SW pins for proper operation. It is
recommended to use ceramic capacitors with a dielectric of X5R or better.
18
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
9.2.3 Application Performance Curves
90
100
80
90
70
80
70
60
Efficiency (%)
Efficiency (%)
VIN = 12 V, VOUT = 1.1 V, TA = 25°C, unless otherwise specified.
50
40
30
60
50
40
30
20
20
10
10
0
0
0
1
2
3
4
Output Current (A)
5
0
6
VIN = 12 V
90
80
80
70
70
60
60
Efficiency (%)
Efficiency (%)
3
4
Output Current (A)
5
6
D015
Figure 19. Efficiency vs Output Current
90
50
40
30
50
40
30
20
20
10
10
0
0.001
0
1
2
VOUT = 1.87 V
Figure 18. Efficiency vs Output Current
0
1
D011
2
3
4
Output Current (A)
5
6
0.010
D016
VOUT = 0.6 V
0.100
Load Current (A)
1.000
10.000
D017
VOUT = 1.1 V
Figure 20. Efficiency vs Output Current
Figure 21. Efficiency vs Load Current
0.8
0.10
0.08
0.06
Line Regulation (%)
Load Regulation (%)
0.6
0.4
0.2
0
0.04
0.02
0.00
-0.02
-0.04
-0.06
-0.2
-0.08
-0.4
-0.10
0
1
2
3
4
Output Current (A)
5
6
4
D012
Figure 22. Load Regulation
6
8
10
12
14
Input Voltage (V)
16
18
20
D013
Figure 23. Line Regulation
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
19
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
20
www.ti.com
Figure 24. Load Transient
Figure 25. Line Transient
Figure 26. Continuous Conduction Mode
(Inductor Current)
Figure 27. Discontinuous Conduction Mode
(Inductor Current)
Figure 28. Skip Mode (Inductor Current)
Figure 29. Start Up With VIN
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
Figure 30. Power Down VIN
Figure 31. Start Up With EN
Figure 32. Power Down with EN
Figure 33. Start Up With EN and Prebias
Figure 34. VOUT Step Up With VID
Figure 35. VOUT Step Down With VID
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
21
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
www.ti.com
Figure 36. Hiccup Current Limit
22
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
TPS566250
www.ti.com
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
10 Power Supply Recommendations
The devices are designed to operate from an input supply range between 4.5 V and 17 V. This input supply must
be well regulated. If the input supply is located more than a few inches from the TPS566250 device, additional
bulk capacitance may be required in addition to the ceramic bypass capacitors.
11 Layout
11.1 Layout Guidelines
•
•
•
•
•
•
•
•
•
•
•
•
•
Keep the input switching current loop as small as possible.
Keep the SW node as physically small and short as possible to minimize parasitic capacitance and
inductance and to minimize radiated emissions. Kelvin connections should be brought from the output to the
feedback terminal of the device.
Keep analog and non-switching components away from switching components.
Make a single point connection from the signal ground to power ground
Keep the pattern lines for VIN and GND broad.
Exposed pad of device must be connected to GND with solder.
Output capacitor should be connected to a broad pattern of the GND.
Voltage feedback loop should be as short as possible, and preferably with ground shield.
Kelvin connections should be brought from the output to the feedback terminal of the device.
Providing sufficient via is preferable for VIN, SW and GND connection.
PCB pattern for VIN, SW, and GND should be as broad as possible.
Input capacitors should be placed as near as possible to the device.
If possible, it is preferred not to allow switching current to flow under the device
11.2 Layout Example
EN
VIN
EN
+3.3V
FB
BOOT
SDA
SDA
SW
SCL
GND
SCL
Exposed Thermal Pad
Thermal VIA
Signal VIA
Figure 37. Layout
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
23
TPS566250
SLVSCV3B – MARCH 2015 – REVISED JUNE 2015
www.ti.com
12 Device and Documentation Support
12.1 Documentation Support
12.2 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
D-CAP2, Eco-mode, PowerPAD, E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
13.1 Thermal Information
This 8-pin DDA package incorporates an exposed thermal pad that is designed to be directly to an external
heatsink. The thermal pad must be soldered directly to the printed board (PCB). After soldering, the PCB can be
used as a heatsink. In addition, through the use of thermal vias, the thermal pad can be attached directly to the
appropriate copper plane shown in the electrical schematic for the device, or alternatively, can be attached to a
special heatsink structure designed into the PCB. This design optimizes the heat transfer from the integrated
circuit (IC).
For additional information on the exposed thermal pad and how to use the advantage of its heat dissipating
abilities, see the Technical Brief, PowerPAD™ Thermally Enhanced Package, Texas Instruments Literature No.
SLMA002 and Application Brief, PowerPAD™ Made Easy, Texas Instruments Literature No. SLMA004. The
exposed thermal pad dimensions for this package are shown in the following illustration.
24
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: TPS566250
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TPS566250DDA
ACTIVE SO PowerPAD
DDA
8
75
RoHS & Green
SN
Level-2-260C-1 YEAR
-40 to 85
566250
TPS566250DDAR
ACTIVE SO PowerPAD
DDA
8
2500
RoHS & Green
SN
Level-2-260C-1 YEAR
-40 to 85
566250
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of