PRELIMINARY PSoC® 4: PSoC 4100PS Datasheet
®
Programmable System-on-Chip (PSoC )
General Description
Cypress' PSoC® 4 is a scalable and reconfigurable platform architecture for a family of programmable embedded system controllers
with an Arm® Cortex™-M0+ CPU. It combines programmable and reconfigurable analog and digital blocks with flexible automatic
routing. PSoC 4100PS is a member of the PSoC 4 platform architecture. It is a combination of a microcontroller with standard
communication and timing peripherals, a capacitive touch-sensing system (CapSense) with best-in-class performance, programmable
general-purpose continuous-time and switched-capacitor analog blocks, and programmable connectivity.
Features
Programmable Analog Blocks
Low-Power Operation
■
Two dedicated analog-to-digital converters (ADC) including a
12-bit SAR ADC and a 10-bit single-slope ADC
■
Four opamps, two low-power comparators, and a flexible
38-channel analog mux to create custom Analog Front Ends
(AFE)
■
1.71-V to 5.5-V operation
■
Deep-Sleep mode with operational analog and 2.5-µA digital
system current
■
Watch Crystal Oscillator (WCO)
■
Two 13-bit Voltage DACs
Programmable GPIO Pins
■
Two 7-bit Current DACs (IDACs) for general-purpose or capacitive sensing applications on any pin
■
Up to 38 GPIOs that can be used for analog, digital, CapSense,
or LCD functions with programmable drive modes, strength and
slew rates
■
Includes eight Smart I/Os to implement pin-level Boolean
operations on input and output signals
■
48-pin QFN, 48-pin TQFP, 28-pin SSOP, and 45-ball WLCSP
packages
CapSense® Capacitive Sensing
■
Cypress's fourth-generation CapSense Sigma-Delta (CSD)
providing best-in-class signal-to-noise ratio (SNR) and water
tolerance
■
Cypress-supplied software component makes capacitive
sensing design easy
PSoC Creator Design Environment
■
Automatic hardware tuning (SmartSense™)
■
Integrated Design Environment (IDE) provides
schematic-capture design entry and build (with automatic
routing of analog and digital signals) and concurrent firmware
development with an ARM-SWD debugger
■
GUI-based configurable PSoC Components with fully
engineered embedded initialization, calibration and correction
algorithms
Application Programming Interfaces (API) for all fixed-function
and programmable peripherals
Segment LCD Drive
■
LCD drive supported on all pins (common or segment)
■
Operates in Deep-Sleep mode with four bits per pin memory
Programmable Digital Peripherals
■
Three independent serial communication blocks (SCBs) that
are run-time configurable as I2C, SPI or UART
■
■
Eight 16-bit timer/counter/pulse-width modulator (TCPWM)
blocks with center-aligned, edge, and pseudo-random modes
Industry-Standard Tool Compatibility
■
32-bit Signal Processing Engine
■
ARM Cortex-M0+ CPU up to 48 MHz
■
Up to 32 KB of flash with read accelerator
■
Up to 4 KB of SRAM
■
Eight-channel descriptor-based DMA controller
Cypress Semiconductor Corporation
Document Number: 002-22097 Rev. *B
•
198 Champion Court
After schematic-capture, firmware development can be done
with ARM-based industry-standard development tools
•
San Jose, CA 95134-1709
•
408-943-2600
Revised May 3, 2018
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
More Information
Cypress provides a wealth of data at www.cypress.com to help you to select the right PSoC device for your design, and to help you
to quickly and effectively integrate the device into your design. For a comprehensive list of resources, see the knowledge base article
KBA86521, How to Design with PSoC 3, PSoC 4, and PSoC 5LP. Following is an abbreviated list for PSoC 4:
■
Overview: PSoC Portfolio, PSoC Roadmap
■
Product Selectors: PSoC 1, PSoC 3, PSoC 4, PSoC 5LP
In addition, PSoC Creator includes a device selection tool.
■
Application notes: Cypress offers a large number of PSoC
application notes covering a broad range of topics, from basic
to advanced level. Recommended application notes for getting
started with PSoC 4 are:
❐ AN79953: Getting Started With PSoC 4
❐ AN88619: PSoC 4 Hardware Design Considerations
❐ AN86439: Using PSoC 4 GPIO Pins
❐ AN57821: Mixed Signal Circuit Board Layout
❐ AN81623: Digital Design Best Practices
❐ AN73854: Introduction To Bootloaders
❐ AN89610: ARM Cortex Code Optimization
®
❐ AN85951: PSoC 4 and PSoC Analog Coprocessor
CapSense® Design Guide
■
■
Software User Guide:
❐ A step-by-step guide for using PSoC Creator. The software
user guide shows you how the PSoC Creator build process
works in detail, how to use source control with PSoC Creator,
and much more.
■
Component Datasheets:
❐ The flexibility of PSoC allows the creation of new peripherals
(components) long after the device has gone into production.
Component datasheets provide all the information needed to
select and use a particular component, including a functional
description, API documentation, example code, and AC/DC
specifications.
■
Online:
❐ In addition to print documentation, the Cypress PSoC forums
connect you with fellow PSoC users and experts in PSoC
from around the world, 24 hours a day, 7 days a week.
Technical Reference Manual (TRM) is in two documents:
❐ Architecture TRM details each PSoC 4 functional block.
❐ Registers TRM describes each of the PSoC 4 registers.
Development Kits:
®
❐ CY8CKIT-147 PSoC 4100PS Prototyping Kit enables you
to evaluate and develop with PSoC 4100PS devices at a low
cost.
The MiniProg3 device provides an interface for flash
programming and debug.
■
Document Number: 002-22097 Rev. *B
Page 2 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
PSoC Creator
PSoC Creator is a free Windows-based Integrated Design Environment (IDE). It enables concurrent hardware and firmware design
of PSoC 3, PSoC 4, and PSoC 5LP based systems. Create designs using classic, familiar schematic capture supported by over 100
pre-verified, production-ready PSoC Components; see the list of component datasheets. With PSoC Creator, you can:
1. Drag and drop component icons to build your hardware
system design in the main design workspace
2. Codesign your application firmware with the PSoC hardware,
using the PSoC Creator IDE C compiler
3. Configure components using the configuration tools
4. Explore the library of 100+ components
5. Review component datasheets
Figure 1. Multiple-Sensor Example Project in PSoC Creator
1
2
3
4
5
Document Number: 002-22097 Rev. *B
Page 3 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Contents
Functional Definition........................................................ 6
CPU and Memory Subsystem ..................................... 6
System Resources ...................................................... 6
Analog Blocks.............................................................. 7
Fixed Function Digital.................................................. 8
GPIO ........................................................................... 8
Special Function Peripherals....................................... 9
WLCSP Package Bootloader ...................................... 9
Pinouts ............................................................................ 10
Alternate Pin Functions ............................................. 12
Power............................................................................... 14
Mode 1: 1.8 V to 5.5 V External Supply .................... 14
Development Support .................................................... 15
Documentation .......................................................... 15
Online ........................................................................ 15
Tools.......................................................................... 15
Electrical Specifications ................................................ 16
Absolute Maximum Ratings....................................... 16
Device Level Specifications....................................... 16
Document Number: 002-22097 Rev. *B
Analog Peripherals ....................................................
Digital Peripherals .....................................................
Memory .....................................................................
System Resources ....................................................
Ordering Information......................................................
Packaging........................................................................
Package Diagrams ....................................................
Acronyms ........................................................................
Document Conventions .................................................
Units of Measure .......................................................
Revision History .............................................................
Sales, Solutions, and Legal Information ......................
Worldwide Sales and Design Support.......................
Products ....................................................................
PSoC® Solutions ......................................................
Cypress Developer Community.................................
Technical Support .....................................................
20
30
32
32
35
37
38
40
42
42
43
44
44
44
44
44
44
Page 4 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Figure 2. Block Diagram
CPU
CPU
Subsystem
Subsystem
SWD/ TC
SPCIF
Cortex
M0+
48 MHz
32- bit
AHB-Lite
FAST MUL
NVIC, IRQMX
FLASH
32 KB
SRAM
4 KB
Read Accelerator
SRAM Controller
System Resources
Lite
Initiator / MMIO
x1
SARMUX
x2
WCO
VDAC
(13-bit)
2x LP Comparator
SAR ADC
( 12-bit)
3x SCB-I2C/SPI/UART
Programmable
Analog
CapSense
Peripheral Interconnect (MMIO)
PCLK
IOSS GPIO (6x ports)
Test
DFT Logic
DFT Analog
ROM Controller
DataWire /
DMA
Peripherals
Clock
Clock Control
WDT
IMO
ILO
Reset
Reset Control
XRES
ROM
8 KB
System Interconnect (Multi Layer AHB)
Power
Sleep Control
WIC
POR
REF
PWRSYS
8x TCPWM
PSoC 4100PS
Architecture
CTB
2 x Opamp x2
High Speed I /O Matrix , Smart I/O
Power Modes
Active/Sleep
Deep Sleep
38 x GPIO, LCD
I/ O Subsystem
PSoC 4100PS devices include extensive support for
programming, testing, debugging, and tracing both hardware
and firmware.
The ARM Serial-Wire Debug (SWD) interface supports all
programming and debug features of the device.
Complete debug-on-chip functionality enables full-device
debugging in the final system using the standard production
device. It does not require special interfaces, debugging pods,
simulators, or emulators. Only the standard programming
connections are required to fully support debug.
The PSoC Creator IDE provides fully integrated programming
and debug support for the PSoC 4100PS devices. The SWD
interface is fully compatible with industry-standard third-party
tools. The PSoC 4100PS family provides a level of security not
possible with multi-chip application solutions or with
microcontrollers. It has the following advantages:
■
Allows disabling of debug features
■
Robust flash protection
■
Allows customer-proprietary functionality to be implemented in
on-chip programmable blocks
Document Number: 002-22097 Rev. *B
The debug circuits are enabled by default and can be disabled
in firmware. If they are not enabled, the only way to re-enable
them is to erase the entire device, clear flash protection, and
reprogram the device with new firmware that enables debugging.
Thus firmware control of debugging cannot be over-ridden
without erasing the firmware thus providing security.
Additionally, all device interfaces can be permanently disabled
(device security) for applications concerned about phishing
attacks due to a maliciously reprogrammed device or attempts to
defeat security by starting and interrupting flash programming
sequences. All programming, debug, and test interfaces are
disabled when maximum device security is enabled. Therefore,
PSoC 4100PS, with device security enabled, may not be
returned for failure analysis. This is a trade-off the PSoC 4100PS
allows the customer to make.
Page 5 of 44
PRELIMINARY
Functional Definition
CPU and Memory Subsystem
CPU
The Cortex-M0+ CPU in the PSoC 4100PS is part of the 32-bit
MCU subsystem, which is optimized for low-power operation
with extensive clock gating. Most instructions are 16 bits in length
and the CPU executes a subset of the Thumb-2 instruction set.
It includes a nested vectored interrupt controller (NVIC) block
with eight interrupt inputs and also includes a Wakeup Interrupt
Controller (WIC). The WIC can wake the processor from Deep
Sleep mode, allowing power to be switched off to the main
processor when the chip is in Deep Sleep mode.
The CPU also includes a debug interface, the serial wire debug
(SWD) interface, which is a two-wire form of JTAG. The debug
configuration used for PSoC 4100PS has four breakpoint
(address) comparators and two watchpoint (data) comparators.
PSoC® 4: PSoC 4100PS Datasheet
instantaneous wake-up on a wake-up event. In Deep Sleep
mode, the high-speed clock and associated circuitry is switched
off; wake-up from this mode takes 35 µs. The opamps can
remain operational in Deep Sleep mode.
Clock System
The PSoC 4100PS clock system is responsible for providing
clocks to all subsystems that require clocks and for switching
between different clock sources without glitching. In addition, the
clock system ensures that there are no metastable conditions.
The clock system for the PSoC 4100PS consists of the internal
main oscillator (IMO), internal low-frequency oscillator (ILO), a
32 kHz Watch Crystal Oscillator (WCO) and provision for an
external clock. Clock dividers are provided to generate clocks for
peripherals on a fine-grained basis. Fractional dividers are also
provided to enable clocking of higher data rates for UARTs.
Figure 3. PSoC 4100PS MCU Clocking Architecture
IM O
DMA/DataWire
The DMA engine will be capable of doing independent data
transfers anywhere within the memory map via a user-programmable descriptor chain. The DataWire capability is used to effect
single-element transfers from one location in memory to another.
There are eight DMA channels with a range of selectable trigger
sources.
E xterna l C lock
WCO
SRAM
Four KB of SRAM are provided with zero wait-state access at
48 MHz.
SROM
Eight KB of SROM are provided that contain boot and configuration routines.
System Resources
Power System
The power system is described in detail in the section Power on
page 14. It provides an assurance that voltage levels are as
required for each respective mode and either delays mode entry
(for example, on power-on reset (POR) until voltage levels are
as required for proper functionality, or generates resets (for
example, on brown-out detection). PSoC 4100PS operates with
a single external supply over the range of either 1.8 V ±5%
(externally regulated) or 1.8 to 5.5 V (internally regulated) and
has three different power modes, transitions between which are
managed by the power system. PSoC 4100PS provides Active,
Sleep, and Deep Sleep low-power modes.
All subsystems are operational in Active mode. The CPU
subsystem (CPU, flash, and SRAM) is clock-gated off in Sleep
mode, while all peripherals and interrupts are active with
Document Number: 002-22097 Rev. *B
W DC0
16-bits
L F C LK
W DC1
16-bits
IL O
W DC2
32-bits
W DT
Flash
The PSoC 4100PS device has a flash module with a flash
accelerator, tightly coupled to the CPU to improve average
access times from the flash block. The low-power flash block is
designed to deliver two wait-state (WS) access time at 48 MHz.
The flash accelerator delivers 85% of single-cycle SRAM access
performance on average.
H F C LK
D ivide B y
2,4,8
W atchdog C ounters (W D C )
W atchdog T im er (W D T )
P re sca le r
S Y S C LK
H F C LK
Inte g er
D ivide rs
F ractio na l
D ivide rs
7 X 16-b it
3 X 16.5-bit, 1X 24.5 b it
The HFCLK signal can be divided down to generate
synchronous clocks for the analog and digital peripherals. There
are 11 clock dividers for PSoC 4100PS as shown in the diagram
above.. The 16-bit capability allows flexible generation of
fine-grained frequency values (there is one 24-bit divider for
large divide ratios), and is fully supported in PSoC Creator.
IMO Clock Source
The IMO is the primary source of internal clocking in
PSoC 4100PS. It is trimmed during testing to achieve the
specified accuracy.The IMO default frequency is 24 MHz and it
can be adjusted from 24 to 48 MHz in steps of 4 MHz. The IMO
tolerance with Cypress-provided calibration settings is ±2%.
ILO Clock Source
The ILO is a very low power, nominally 40-kHz oscillator, which
is primarily used to generate clocks for the watchdog timer
(WDT) and peripheral operation in Deep Sleep mode. ILO-driven
counters can be calibrated to the IMO to improve accuracy.
Cypress provides a software component, which does the
calibration.
Page 6 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Watch Crystal Oscillator (WCO)
Analog Blocks
The PSoC 4100PS clock subsystem also implements a
low-frequency (32-kHz watch crystal) oscillator that can be used
for Watchdog timing applications.
12-bit SAR ADC
Watchdog Timer
The 12-bit, 1-Msps SAR ADC can operate at a maximum clock
rate of 18 MHz and requires a minimum of 18 clocks at that
frequency to do a 12-bit conversion.
A watchdog timer is implemented in the clock block running from
the ILO; this allows watchdog operation during Deep Sleep and
generates a watchdog reset if not serviced before the set timeout
occurs. The watchdog reset is recorded in a Reset Cause
register, which is firmware readable.
The Sample-and-Hold (S/H) aperture is programmable allowing
the gain bandwidth requirements of the amplifier driving the SAR
inputs, which determine its settling time, to be relaxed if required.
It is possible to provide an external bypass (through a fixed pin
location) for the internal reference amplifier.
Reset
PSoC 4100PS can be reset from a variety of sources including
a software reset. Reset events are asynchronous and guarantee
reversion to a known state. The reset cause is recorded in a
register, which is sticky through reset and allows software to
determine the cause of the reset. An XRES pin is reserved for
external reset by asserting it active low. The XRES pin has an
internal pull-up resistor that is always enabled.
Voltage Reference
The PSoC 4100PS reference system generates all internally
required references. A 1.2-V voltage reference is provided for the
comparator. The IDACs are based on a ±5% reference.
The SAR is connected to a fixed set of pins through an 8-input
sequencer. The sequencer cycles through selected channels
autonomously (sequencer scan) with zero switching overhead
(that is, aggregate sampling bandwidth is equal to 1 Msps
whether it is for a single channel or distributed over several
channels). The sequencer switching is effected through a state
machine or through firmware driven switching. A feature
provided by the sequencer is buffering of each channel to reduce
CPU interrupt service requirements. To accommodate signals
with varying source impedance and frequency, it is possible to
have different sample times programmable for each channel.
Also, signal range specification through a pair of range registers
(low and high range values) is implemented with a corresponding
out-of-range interrupt if the digitized value exceeds the
programmed range; this allows fast detection of out-of-range
values without the necessity of having to wait for a sequencer
scan to be completed and the CPU to read the values and check
for out-of-range values in software.
The SAR is not available in Deep Sleep mode as it requires a
high-speed clock (up to 18 MHz). The SAR operating range is
1.71 V to 5.5 V.
Figure 4. SAR ADC
AHB System Bus and Programmable Logic
Interconnect
SAR Sequencer
vminus vplus
Data and
Status Flags
POS
SARADC
NEG
P7
SARMUX Port
(8 inputs)
SARMUX
P0
Sequencing
and Control
External
Reference
and
Bypass
(optional )
Reference
Selection
VDDA/2
VDDA
VREF
Inputs from other Ports
Four Opamps (Continuous-Time Block; CTB)
VDAC (13 bits)
PSoC 4100PS has four opamps with Comparator modes which
allow most common analog functions to be performed on-chip
eliminating external components; PGAs, Voltage Buffers, Filters,
Trans-Impedance Amplifiers, and other functions can be
realized, in some cases with external passives, saving power,
cost, and space. The on-chip opamps are designed with enough
bandwidth to drive the Sample-and-Hold circuit of the ADC
without requiring external buffering.
The PSoC 4100PS has two 13-bit resolution Voltage DACs.
Document Number: 002-22097 Rev. *B
Low-power Comparators (LPC)
PSoC 4100PS has a pair of low-power comparators, which can
also operate in Deep Sleep modes. This allows the analog
system blocks to be disabled while retaining the ability to monitor
external voltage levels during low-power modes. The
comparator outputs are normally synchronized to avoid
metastability unless operating in an asynchronous power mode
where the system wake-up circuit is activated by a comparator
switch event. The LPC outputs can be routed to pins.
Page 7 of 44
PRELIMINARY
Current DACs
PSoC 4100PS has two IDACs, which can drive any of the pins
on the chip. These IDACs have programmable current ranges.
Analog Multiplexed Buses
PSoC 4100PS has two concentric independent buses that go
around the periphery of the chip. These buses (called amux
buses) are connected to firmware-programmable analog
switches that allow the chip's internal resources (IDACs,
comparator) to connect to any pin on the I/O Ports.
Temperature Sensor
There is an on-chip temperature sensor which is calibrated
during production to achieve ±1% typical (±5% maximum)
deviation from accuracy. The SAR ADC is used to measure the
temperature.
Fixed Function Digital
Timer/Counter/PWM (TCPWM) Block
The TCPWM block consists of a 16-bit counter with
user-programmable period length. There is a capture register to
record the count value at the time of an event (which may be an
I/O event), a period register that is used to either stop or
auto-reload the counter when its count is equal to the period
register, and compare registers to generate compare value
signals that are used as PWM duty cycle outputs. The block also
provides true and complementary outputs with programmable
offset between them to allow use as dead-band programmable
complementary PWM outputs. It also has a Kill input to force
outputs to a predetermined state; for example, this is used in
motor drive systems when an over-current state is indicated and
the PWM driving the FETs needs to be shut off immediately with
no time for software intervention. There are eight TCPWM blocks
in PSoC 4100PS.
Serial Communication Block (SCB)
PSoC 4100PS has three serial communication blocks, which can
be programmed to have SPI, I2C, or UART functionality.
I2C Mode: The hardware I2C block implements a full
multi-master and slave interface (it is capable of multi-master
arbitration). This block is capable of operating at speeds of up to
1 Mbps (Fast Mode Plus) and has flexible buffering options to
reduce interrupt overhead and latency for the CPU. It also
supports EZI2C that creates a mailbox address range in the
memory of PSoC 4100PS and effectively reduces I2C communication to reading from and writing to an array in memory. In
addition, the block supports an 8-deep FIFO for receive and
transmit which, by increasing the time given for the CPU to read
data, greatly reduces the need for clock stretching caused by the
CPU not having read data on time.
The I2C peripheral is compatible with the I2C Standard-mode and
Fast-mode devices as defined in the NXP I2C-bus specification
and user manual (UM10204). The I2C bus I/O is implemented
with GPIO in open-drain modes.
Document Number: 002-22097 Rev. *B
PSoC® 4: PSoC 4100PS Datasheet
PSoC 4100PS is not completely compliant with the I2C spec in
the following respect:
■
GPIO cells are not overvoltage tolerant and, therefore, cannot
be hot-swapped or powered up independently of the rest of the
I2C system.
UART Mode: This is a full-feature UART operating at up to
1 Mbps. It supports automotive single-wire interface (LIN),
infrared interface (IrDA), and SmartCard (ISO7816) protocols, all
of which are minor variants of the basic UART protocol. In
addition, it supports the 9-bit multiprocessor mode that allows
addressing of peripherals connected over common RX and TX
lines. Common UART functions such as parity error, break
detect, and frame error are supported. An 8-deep FIFO allows
much greater CPU service latencies to be tolerated.
SPI Mode: The SPI mode supports full Motorola SPI, TI SSP
(adds a start pulse used to synchronize SPI Codecs), and
National Microwire (half-duplex form of SPI). The SPI block can
use the FIFO.
GPIO
PSoC 4100PS has up to 38 GPIOs. The GPIO block implements
the following:
■ Eight drive modes:
❐ Analog input mode (input and output buffers disabled)
❐ Input only
❐ Weak pull-up with strong pull-down
❐ Strong pull-up with weak pull-down
❐ Open drain with strong pull-down
❐ Open drain with strong pull-up
❐ Strong pull-up with strong pull-down
❐ Weak pull-up with weak pull-down
■ Input threshold select (CMOS or LVTTL).
■ Individual control of input and output buffer enabling/disabling
in addition to the drive strength modes
■ Selectable slew rates for dV/dt related noise control to improve
EMI
The pins are organized in logical entities called ports, which are
8-bit in width (less for Ports 2 and 3). During power-on and reset,
the blocks are forced to the disable state so as not to crowbar
any inputs and/or cause excess turn-on current. A multiplexing
network known as a high-speed I/O matrix is used to multiplex
between various signals that may connect to an I/O pin.
Data output and pin state registers store, respectively, the values
to be driven on the pins and the states of the pins themselves.
Every I/O pin can generate an interrupt if so enabled and each
I/O port has an interrupt request (IRQ) and interrupt service
routine (ISR) vector associated with it (4 for PSoC 4100PS). The
Smart I/O block is a fabric of switches and LUTs that allows
Boolean functions to be performed on signals being routed to the
pins of a GPIO port. The Smart I/O block can perform logical
operations on input pins to the chip and on signals going out as
outputs.
Page 8 of 44
PRELIMINARY
Special Function Peripherals
CapSense
CapSense is supported in PSoC 4100PS through a CSD block
that can be connected to any pins through an analog mux bus
via an analog switch. CapSense function can thus be provided
on any available pin or group of pins in a system under software
control. A PSoC Creator component is provided for the
CapSense block to make it easy for the user.
Shield voltage can be driven on another mux bus to provide
water-tolerance capability. Water tolerance is provided by driving
the shield electrode in phase with the sense electrode to keep
the shield capacitance from attenuating the sensed input.
Proximity sensing can also be implemented.
The CapSense block has two IDACs, which can be used for
general purposes if CapSense is not being used (both IDACs are
Document Number: 002-22097 Rev. *B
PSoC® 4: PSoC 4100PS Datasheet
available in that case) or if CapSense is used without water
tolerance (one IDAC is available). The CapSense block also
provides a 10-bit Slope ADC function, which can be used in
conjunction with the CapSense function.
The CapSense block is an advanced, low-noise, programmable
block with programmable voltage references and current source
ranges for improved sensitivity and flexibility. It can also use an
external reference voltage. It has a full-wave CSD mode that
alternates sensing to VDDA and ground to null out power-supply
related noise
WLCSP Package Bootloader
The WLCSP package is supplied with an I2C bootloader installed
in flash. The bootloader is compatible with PSoC Creator
bootloader project files.
Page 9 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Pinouts
The following table provides the pin list for PSoC 4100PS for the 48 QFN, 48 TQFP, 45 WLCSP, and 28 SSOP packages. All port pins
support GPIO.
Packages
48-QFN
48-TQFP
28-SSOP
45-CSP
Pin
Name
Pin
Name
Pin
Name
Pin
Name
28
P0.0
28
P0.0
21
P0.0
D3
P0.0
29
P0.1
29
P0.1
22
P0.1
E2
P0.1
30
P0.2
30
P0.2
23
P0.2
D2
P0.2
31
P0.3
31
P0.3
C3
P0.3
32
P0.4
32
P0.4
D1
P0.4
33
P0.5
33
P0.5
E1
P0.5
34
P0.6
34
P0.6
C2
P0.6
35
P0.7
35
P0.7
B2
P0.7
36
XRES
36
XRES
B3
XRES
37
P4.0
37
P4.0
A1
P4.0
38
P4.1
38
P4.1
B1
P4.1
39
P5.0
39
P5.0
B4
P5.0
40
P5.1
40
P5.1
41
P5.2
41
42
P5.3
43
VDDA
44
VSSA
44
VSSA
45
VCCD
45
46
VSSD
47
48
24
XRES
25
P5.0
C1
P5.1
P5.2
26
P5.2
A2
P5.2
42
P5.3
27
P5.3
A3
P5.3
43
VDDA
28
VDDA
J2
VDDA
J3
VSSA
VCCD
1
VCCD
A4
VCCD
B5
VDDD
46
VSSD
2
VSSD
A5
VSSD
VDDD
47
VDDD
3
VDDD
P1.0
48
P1.0
4
P1.0
C5
P1.0
1
P1.1
1
P1.1
5
P1.1
C4
P1.1
2
P1.2
2
P1.2
6
P1.2
D5
P1.2
3
P1.3
3
P1.3
7
P1.3
D4
P1.3
4
P1.4
4
P1.4
E3
P1.4
5
P1.5
5
P1.5
E4
P1.5
6
P1.6
6
P1.6
7
P1.7
7
P1.7
8
VDDA
8
VDDA
G3
P1.7
8
VDDA
E5
VDDA
9
VSSA
9
VSSA
9
VSSA
F5
VSSA
10
P2.0
10
P2.0
10
P2.0
F4
P2.0
11
P2.1
11
P2.1
11
P2.1
F3
P2.1
12
P2.2
12
P2.2
12
P2.2
G4
P2.2
13
P2.3
13
P2.3
13
P2.3
G5
P2.3
14
P2.4
14
P2.4
H5
P2.4
15
P2.5
15
P2.5
J4
P2.5
Document Number: 002-22097 Rev. *B
Page 10 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Packages
48-QFN
Pin
48-TQFP
Name
Pin
Name
16
P2.6
16
P2.6
17
P2.7/VREF
17
P2.7/VREF
18
VSSA
18
VSSA
19
VDDA
19
VDDA
20
P3.0
20
P3.0
21
P3.1
21
22
P3.2
23
P3.3
24
25
28-SSOP
Pin
Name
14
P2.7/VREF
15
VDDA
P3.1
16
P3.1
22
P3.2
17
23
P3.3
18
P3.4
24
P3.5
25
26
P3.6
26
P3.6
19
27
P3.7
27
P3.7
20
45-CSP
Pin
Name
H4
P2.6
J5
P2.7/VREF
J3
VSSA
J2
VDDA
H2
P3.0
F2
P3.1
P3.2
J1
P3.2
P3.3
H3
P3.3
P3.4
F1
P3.4
P3.5
G2
P3.5
P3.6
G1
P3.6
P3.7
H1
P3.7
Descriptions of the Power pins are as follows:
VDDD: Power supply for the digital section.
VDDA: Power supply for the analog section.
VSS: Ground pin.
VCCD: Regulated digital supply (1.8 V ±5%)
The 48-pin packages have 38 I/O pins. The 45 CSP and the 28 SSOP have 37 and 20 I/O pins respectively
Document Number: 002-22097 Rev. *B
Page 11 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Alternate Pin Functions
Each Port pin has can be assigned to one of multiple functions; it can, for example, be an Analog I/O, a Digital Peripheral function, or a CapSense or LCD pin. The pin
assignments are shown in the following table.
Active
Port/Pin
Analog
P0.0
SmartIO
ACT #0
ACT #1
DeepSleep
ACT #2
ACT #3
DS #0
DS #1
tcpwm.tr_in[0]
cpuss.swd_data:0
scb[0].spi_select1:0
tcpwm.tr_in[1]
cpuss.swd_clk:0
SmartIO[0].io[0]
tcpwm.line[4]:1
P0.1
SmartIO[0].io[1]
tcpwm.line_compl[4]:1
P0.2
SmartIO[0].io[2]
tcpwm.line[5]:1
P0.3
SmartIO[0].io[3]
tcpwm.line_compl[5]:1
P0.4
SmartIO[0].io[4]
tcpwm.line[6]:1
scb[1].uart_rx:0
scb[1].i2c_scl:0
scb[1].spi_mosi:0
P0.5
SmartIO[0].io[5]
tcpwm.line_compl[6]:1
scb[1].uart_tx:0
scb[1].i2c_sda:0
scb[1].spi_miso:0
P0.6
SmartIO[0].io[6]
scb[1].uart_cts:0
lpcomp.comp[0]:0
scb[1].spi_clk:0
P0.7
SmartIO[0].io[7]
scb[1].uart_rts:0
lpcomp.comp[1]:0
scb[1].spi_select0:0
scb[2].spi_mosi:1
srss.ext_clk
scb[0].spi_select2:0
scb[0].spi_select3:0
P4.0
wco_in
tcpwm.line[0]:2
scb[2].uart_rx:1
tcpwm.tr_in[5]
scb[2].i2c_scl:1
P4.1
wco_out
tcpwm.line_compl[0]:2
scb[2].uart_tx:1
tcpwm.tr_in[6]
scb[2].i2c_sda:1
scb[2].spi_miso:1
P5.0
csd.cshieldpads
tcpwm.line[7]:1
scb[0].uart_rx:1
scb[0].i2c_scl:1
scb[0].spi_mosi:1
P5.1
csd.vref_ext
tcpwm.line_compl[7]:1
scb[0].uart_tx:1
scb[0].i2c_sda:1
scb[0].spi_miso:1
P5.2
csd.dsi_cmod
tcpwm.line[6]:2
scb[0].uart_cts:1
P5.3
csd.dsi_csh_tank
tcpwm.line_compl[6]:2
scb[0].uart_rts:1
P1.0
ctb_pads[8]
lpcomp.in_p[1]
tcpwm.line[0]:1
scb[1].uart_rx:1
scb[1].i2c_scl:1
scb[1].spi_mosi:1
P1.1
ctb_pads[9]
lpcomp.in_n[1]
tcpwm.line_compl[0]:1
scb[1].uart_tx:1
scb[1].i2c_sda:1
scb[1].spi_miso:1
P1.2
ctb_pads[10]
ctb_oa0_out_10x[1]
tcpwm.line[1]:1
scb[1].uart_cts:1
scb[1].spi_clk:1
P1.3
ctb_pads[11]
ctb_oa1_out_10x[1]
tcpwm.line_compl[1]:1
scb[1].uart_rts:1
scb[1].spi_select0:1
P1.4
ctb_pads[12]
tcpwm.line[2]:1
scb[1].spi_select1:0
P1.5
ctb_pads[13]
tcpwm.line_compl[2]:1
scb[1].spi_select2:0
P1.6
ctb_pads[14]
tcpwm.line[3]:1
scb[1].spi_select3:0
P1.7
ctb_pads[15]
tcpwm.line_compl[3]:1
P2.0
ctb_pads[0]
tcpwm.line[4]:0
Document Number: 002-22097 Rev. *B
scb[2].uart_rx:0
tr_sar_out
scb[0].spi_clk:1
scb[0].spi_select0:1
scb[2].i2c_scl:0
scb[2].spi_mosi:0
Page 12 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Active
Port/Pin
Analog
P2.1
SmartIO
DeepSleep
ACT #0
ACT #1
ctb_pads[1]
tcpwm.line_compl[4]:0
scb[2].uart_tx:0
P2.2
ctb_pads[2]
ctb_oa0_out_10x[0]
tcpwm.line[5]:0
scb[2].uart_cts:0
scb[2].spi_clk:0
P2.3
ctb_pads[3]
ctb_oa1_out_10x[0]
tcpwm.line_compl[5]:0
scb[2].uart_rts:0
scb[2].spi_select0:0
P2.4
ctb_pads[4]
tcpwm.line[0]:0
scb[2].spi_select1:0
P2.5
ctb_pads[5]
tcpwm.line_compl[0]:0
scb[2].spi_select2:0
P2.6
ctb_pads[6]
tcpwm.line[1]:0
scb[2].spi_select3:0
ctb_pads[7]
tcpwm.line_compl[1]:0
P2.7
ACT #2
ACT #3
DS #0
DS #1
scb[2].i2c_sda:0
scb[2].spi_miso:0
sar_ext_vref0
sar_ext_vref1
P3.0
sarmux[0]
tcpwm.line[2]:0
scb[0].uart_rx:0
scb[0].i2c_scl:0
scb[0].spi_mosi:0
P3.1
sarmux[1]
tcpwm.line_compl[2]:0
scb[0].uart_tx:0
scb[0].i2c_sda:0
scb[0].spi_miso:0
P3.2
sarmux[2]
lpcomp.in_p[0]
tcpwm.line[3]:0
scb[0].uart_cts:0
scb[0].spi_clk:0
P3.3
sarmux[3]
lpcomp.in_n[0]
tcpwm.line_compl[3]:0
scb[0].uart_rts:0
scb[0].spi_select0:0
P3.4
sarmux[4]
tcpwm.line[6]:0
tcpwm.tr_in[2]
P3.5
sarmux[5]
tcpwm.line_compl[6]:0
tcpwm.tr_in[3]
csd.comp
scb[0].spi_select2:1
P3.6
sarmux[6]
tcpwm.line[7]:0
scb[2].uart_rx:2
tcpwm.tr_in[4]
scb[2].i2c_scl:2
scb[2].spi_mosi:2
P3.7
sarmux[7]
tcpwm.line_compl[7]:0
scb[2].uart_tx:2
scb[2].i2c_sda:2
scb[2].spi_miso:2
scb[0].spi_select1:1
Refer to the Technical Reference Manual (TRM) for CTB connection details. The VDAC outputs are buffered through the CTB outputs; any VDAC output may be routed to
any CTB output.
Document Number: 002-22097 Rev. *B
Page 13 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
regulator operational). In Mode 2, the supply range is1.8 V ±5%
(externally regulated; 1.71 to 1.89, internal regulator bypassed).
Power
The following power system diagram shows the set of power
supply pins as implemented for the PSoC 4100PS. The system
has one regulator in Active mode for the digital circuitry. There is
no analog regulator; the analog circuits run directly from the
VDDA input.
Note that VDDD and VDDA must be shorted together on the
PCB.
Figure 5. Power Supply Connections
VDDA
VDDA
Digital
Domain
Analog
Domain
In this mode, the PSoC 4100PS is powered by an external power
supply that must be within the range of 1.71 to 1.89 V; note that
this range needs to include the power supply ripple too. In this
mode, the VDDD and VCCD pins are shorted together and
bypassed.
VSSA
VCCD
1.8 Volt
Reg
In this mode, the PSoC 4100PS is powered by an external power
supply that can be anywhere in the range of 1.8 to 5.5 V. This
range is also designed for battery-powered operation. For
example, the chip can be powered from a battery system that
starts at 3.5 V and works down to 1.8 V. In this mode, the internal
regulator of the PSoC 4100PS supplies the internal logic and its
output is connected to the VCCD pin. The VCCD pin must be
bypassed to ground via an external capacitor (0.1 µF; X5R
ceramic or better) and must not be connected to anything else.
Mode 2: 1.8 V ±5% External Supply
VDDD
VDDD
Mode 1: 1.8 V to 5.5 V External Supply
Bypass capacitors must be used from VDDD and VDDA to ground.
The typical practice for systems in this frequency range is to use
a capacitor in the 1-µF range, in parallel with a smaller capacitor
(0.1 µF, for example). Note that these are simply rules of thumb
and that, for critical applications, the PCB layout, lead inductance, and the bypass capacitor parasitic should be simulated to
design and obtain optimal bypassing.
VSSD
There are two distinct modes of operation. In Mode 1, the supply
voltage range is 1.8 V to 5.5 V (unregulated externally; internal
An example of a bypass scheme is shown in the following
diagram.
Figure 6. External Supply Range from 1.8 V to 5.5 V with Internal Regulator Active
Power supply bypass connections example
1. 8 V to 5.5 V
1. 8 V to 5.5 V
VDDD
1 µF
VDDA
1 µF
0. 1 µF
0. 1 µF
VCCD
0. 1 µF
PSoC CY8C4Axx
VSS
Document Number: 002-22097 Rev. *B
Page 14 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Development Support
The PSoC 4100PS family has a rich set of documentation,
development tools, and online resources to assist you during
your development process. Visit www.cypress.com/go/psoc4 to
find out more.
Documentation
A suite of documentation supports the PSoC 4100PS family to
ensure that you can find answers to your questions quickly. This
section contains a list of some of the key documents.
Software User Guide: A step-by-step guide for using PSoC
Creator. The software user guide shows you how the PSoC
Creator build process works in detail, how to use source control
with PSoC Creator, and much more.
Component Datasheets: The flexibility of PSoC allows the
creation of new peripherals (components) long after the device
has gone into production. Component data sheets provide all of
the information needed to select and use a particular component,
including a functional description, API documentation, example
code, and AC/DC specifications.
Technical Reference Manual: The Technical Reference Manual
(TRM) contains all the technical detail you need to use a PSoC
device, including a complete description of all PSoC registers.
The TRM is available in the Documentation section at
www.cypress.com/psoc4.
Online
In addition to print documentation, the Cypress PSoC forums
connect you with fellow PSoC users and experts in PSoC from
around the world, 24 hours a day, 7 days a week.
Tools
With industry standard cores, programming, and debugging
interfaces, the PSoC 4100PS family is part of a development tool
ecosystem. Visit us at www.cypress.com/go/psoccreator for the
latest information on the revolutionary, easy to use PSoC Creator
IDE, supported third party compilers, programmers, debuggers,
and development kits.
Application Notes: PSoC application notes discuss a particular
application of PSoC in depth; examples include brushless DC
motor control and on-chip filtering. Application notes often
include example projects in addition to the application note
document.
Document Number: 002-22097 Rev. *B
Page 15 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Electrical Specifications
Absolute Maximum Ratings
Table 1. Absolute Maximum Ratings[1]
Spec ID#
Parameter
Description
Min
Typ
Max
SID1
VDD_ABS
Digital or Analog supply relative to VSS
–0.5
–
6
SID2
VCCD_ABS
Direct digital core voltage input relative
to VSS
–0.5
–
1.95
SID3
VGPIO_ABS
GPIO voltage
–0.5
–
VDD+0.5
SID4
IGPIO_ABS
Maximum current per GPIO
–25
–
25
SID5
IGPIO_injection
GPIO injection current, Max for VIH >
VDDD, and Min for VIL < VSS
–0.5
–
0.5
BID44
ESD_HBM
Electrostatic discharge human body
model
2200
–
–
Details/
Conditions
Units
VDDD, VDDA,
Absolute Max
V
–
–
–
mA
Current injected
per pin
–
V
BID45
ESD_CDM
Electrostatic discharge charged device
model
500
–
–
BID46
LU
Pin current for latch-up
–140
–
140
–
mA
–
Device Level Specifications
All specifications are valid for –40 °C TA 105 °C and TJ 125 °C, except where noted. Specifications are valid for 1.71 V to 5.5 V,
except where noted.
Table 2. DC Specifications
Typical values measured at VDD = 3.3 V and 25 °C.
Spec ID#
Parameter
Description
Min
Typ
Max
SID53
VDD
Power supply input voltage
1.8
–
5.5
SID255
VDD
Power supply input voltage (VCCD =
VDD)
1.71
–
1.89
SID54
VDDIO
VDDIO domain supply
1.71
–
VDD
SID55
CEFC
External regulator voltage bypass
–
0.1
–
SID56
CEXC
Power supply bypass capacitor
–
1
–
Units
Details/
Conditions
With regulator
enabled
V
Internally
unregulated supply
–
µF
X5R ceramic or
better
X5R ceramic or
better
Active Mode, VDD = 1.8 V to 5.5 V. Typical values measured at VDD = 3.3 V and 25 °C.
SID9
IDD5
Execute from flash; CPU at 6 MHz
–
2
–
SID12
IDD8
Execute from flash; CPU at 24 MHz
–
5.6
–
SID16
IDD11
Execute from flash; CPU at 48 MHz
–
10.4
–
–
1.1
–
–
3.1
–
–
–
mA
–
Sleep Mode, VDDD = 1.8 V to 5.5 V (Regulator on)
SID22
SID25
IDD17
IDD20
I2C wakeup WDT, and Comparators on
2
I C wakeup, WDT, and Comparators
on.
mA
6 MHz
12 MHz
Note
1. Usage above the absolute maximum conditions listed in Table 1 may cause permanent damage to the device. Exposure to Absolute Maximum conditions for extended
periods of time may affect device reliability. The Maximum Storage Temperature is 150 °C in compliance with JEDEC Standard JESD22-A103, High Temperature
Storage Life. When used below Absolute Maximum conditions but above normal operating conditions, the device may not operate to specification.
Document Number: 002-22097 Rev. *B
Page 16 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 2. DC Specifications (continued)
Typical values measured at VDD = 3.3 V and 25 °C.
Spec ID#
Parameter
Description
Details/
Conditions
Min
Typ
Max
Units
–
1.1
–
mA
6 MHz
–
3.1
–
mA
12 MHz
–
2.5
–
µA
–
–
2.5
–
µA
–
Sleep Mode, VDDD = 1.71 V to 1.89 V (Regulator bypassed)
SID28
IDD23
SID28A
IDD23A
I2C wakeup, WDT, and Comparators on
2
I C wakeup, WDT, and Comparators on
Deep Sleep Mode, VDD = 1.8 V to 3.6 V (Regulator on)
SID31
IDD26
I2C wakeup and WDT on
Deep Sleep Mode, VDD = 3.6 V to 5.5 V (Regulator on)
SID34
IDD29
I2C wakeup and WDT on
Deep Sleep Mode, VDD = 1.71 V to 1.89 V (Regulator bypassed)
SID37
IDD32
I2C wakeup and WDT on
–
2.5
–
µA
–
IDD_XR
Supply current while XRES asserted
–
115
300
µA
–
XRES Current
SID307
Table 3. AC Specifications
Spec ID#
SID48
Parameter
Description
Min
Typ
Max
Units
Details/
Conditions
DC
–
48
MHz
1.71 VDD 5.5
FCPU
CPU frequency
SID49
TSLEEP
Wakeup from Sleep mode
–
0
–
SID50[2]
TDEEPSLEEP
Wakeup from Deep Sleep mode
–
35
–
[2]
µs
Note
2. Guaranteed by characterization.
Document Number: 002-22097 Rev. *B
Page 17 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
GPIO
Table 4. GPIO DC Specifications
Spec ID#
Parameter
Description
Min
Typ
Max
Units
Details/
Conditions
SID57
VIH[3]
Input voltage high threshold
0.7 VDDD
–
–
CMOS Input
SID58
VIL
Input voltage low threshold
–
–
CMOS Input
SID241
VIH[3]
LVTTL input, VDDD < 2.7 V
0.7 VDDD
0.3
VDDD
–
–
–
SID242
VIL
LVTTL input, VDDD < 2.7 V
–
–
0.3
VDDD
–
SID243
VIH[3]
LVTTL input, VDDD 2.7 V
2.0
–
–
–
SID244
VIL
LVTTL input, VDDD 2.7 V
–
–
0.8
SID59
VOH
Output voltage high level
VDDD –0.6
–
–
IOH = 4 mA at 3 V VDDD
SID60
VOH
Output voltage high level
VDDD –0.5
–
–
IOH = 1 mA at 1.8 V
VDDD
SID61
VOL
Output voltage low level
–
–
0.6
IOL = 4 mA at 1.8 V
VDDD
SID62
VOL
Output voltage low level
–
–
0.6
IOL = 10 mA at 3 V VDDD
SID62A
VOL
Output voltage low level
–
–
0.4
IOL = 3 mA at 3 V VDDD
SID63
RPULLUP
Pull-up resistor
3.5
5.6
8.5
SID64
RPULLDOWN
Pull-down resistor
3.5
5.6
8.5
SID65
IIL
Input leakage current (absolute
value)
–
2
–
nA
SID66
CIN
Input capacitance
–
3
7
pF
–
SID67
VHYSTTL
Input hysteresis LVTTL
15
40
–
SID68[4]
VHYSCMOS
Input hysteresis CMOS
0.05 × VDDD
–
–
mV
VDD < 4.5 V
SID68A[4]
VHYSCMOS5V5 Input hysteresis CMOS
200
–
–
SID69[4]
IDIODE
Current through protection diode to
VDD/VSS
–
–
100
µA
–
SID69A[4]
ITOT_GPIO
Maximum total source or sink chip
current
–
–
85
mA
–
[4]
V
kΩ
–
–
–
VDDD 2.7 V
VDD > 4.5 V
Table 5. GPIO AC Specifications
(Guaranteed by Characterization)
Spec ID#
SID70
Parameter
TRISEF
Description
Rise time in fast strong mode
Min
Typ
Max
2
–
12
Units
ns
SID71
TFALLF
Fall time in fast strong mode
2
–
12
SID72
TRISES
Rise time in slow strong mode
10
–
60
ns
Details/
Conditions
3.3 V VDDD, Cload =
25 pF
3.3 V VDDD, Cload =
25 pF
3.3 V VDDD, Cload =
25 pF
Notes
3. VIH must not exceed VDDD + 0.2 V.
4. Guaranteed by characterization.
Document Number: 002-22097 Rev. *B
Page 18 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 5. GPIO AC Specifications
(Guaranteed by Characterization) (continued)
Spec ID#
Parameter
Description
Min
Typ
Max
Units
ns
Details/
Conditions
3.3 V VDDD, Cload =
25 pF
SID73
TFALLS
Fall time in slow strong mode
10
–
60
SID74
FGPIOUT1
GPIO FOUT; 3.3 V VDDD 5.5 V
Fast strong mode
–
–
16
90/10%, 25-pF load,
60/40 duty cycle
SID75
FGPIOUT2
GPIO FOUT; 1.71 VVDDD3.3 V
Fast strong mode
–
–
16
90/10%, 25-pF load,
60/40 duty cycle
SID76
FGPIOUT3
GPIO FOUT; 3.3 V VDDD 5.5 V
Slow strong mode
–
–
7
SID245
FGPIOUT4
GPIO FOUT; 1.71 V VDDD 3.3 V
Slow strong mode.
–
–
3.5
90/10%, 25-pF load,
60/40 duty cycle
SID246
FGPIOIN
GPIO input operating frequency;
1.71 V VDDD 5.5 V
–
–
16
90/10% VIO
Min
Typ
MHz
90/10%, 25-pF load,
60/40 duty cycle
XRES
Table 6. XRES DC Specifications
Spec ID#
Parameter
Description
Max
Units
Details/
Conditions
SID77
VIH
Input voltage high threshold
0.7 × VDDD
–
–
SID78
VIL
Input voltage low threshold
–
–
0.3 VDDD
SID79
RPULLUP
Pull-up resistor
–
60
–
kΩ
–
SID80
CIN
Input capacitance
–
3
7
pF
–
SID81[5]
VHYSXRES
Input voltage hysteresis
–
05*VDD
–
mV
V
CMOS Input
Typical hysteresis is
200 mV for VDD > 4.5 V
Table 7. XRES AC Specifications
Spec ID#
Parameter
Description
Min
Typ
Max
Units
Details/
Conditions
SID83[5]
TRESETWIDTH
Reset pulse width
1
–
–
µs
–
BID194[5]
TRESETWAKE
Wake-up time from reset
release
–
–
2.5
ms
–
Note
5. Guaranteed by characterization.
Document Number: 002-22097 Rev. *B
Page 19 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Analog Peripherals
Table 8. CTB Opamp Specifications
Spec ID#
Parameter
Description
Min
Typ
Max
Units
Details/Conditions
IDD
Opamp block current, No load
SID269
IDD_HI
power=hi
–
1100
1850
SID270
IDD_MED
power=med
–
550
950
SID271
IDD_LOW
power=lo
–
150
350
GBW
Load = 20 pF, 0.1 mA
VDDA = 2.7 V
SID272
GBW_HI
power=hi
6
–
–
SID273
GBW_MED
power=med
3
–
–
SID274
GBW_LO
power=lo
–
1
–
Input and output are
0.2 V to VDDA-0.2 V
IOUT_MAX
VDDA = 2.7 V, 500 mV from rail
SID275
IOUT_MAX_HI
power=hi
10
–
–
Output is 0.5 V
VDDA-0.5 V
SID276
IOUT_MAX_MID
power=mid
10
–
–
SID277
IOUT_MAX_LO
power=lo
–
5
–
Output is 0.5 V
VDDA-0.5 V
IOUT
VDDA = 1.71 V, 500 mV from rail
SID278
IOUT_MAX_HI
power=hi
4
–
–
Output is 0.5 V
VDDA-0.5 V
SID279
IOUT_MAX_MID
power=mid
4
–
–
SID280
IOUT_MAX_LO
power=lo
–
2
–
IDD_Int
Opamp block current Internal Load
SID269_I
IDD_HI_Int
power=hi
–
1500
1700
SID270_I
IDD_MED_Int
power=med
–
700
900
GBW
VDDA = 2.7 V
GBW_HI_Int
power=hi
8
–
–
SID272_I
–
µA
–
–
Input and output are
0.2 V to VDDA-0.2 V
MHz
mA
mA
Input and output are
0.2 V to VDDA-0.2 V
Output is 0.5 V
VDDA-0.5 V
Output is 0.5 V
VDDA-0.5 V
Output is 0.5 V
VDDA-0.5 V
–
µA
MHz
–
Output is 0.25 V to
VDDA-0.25 V
General opamp specs for both internal and external modes
SID281
VIN
Charge-pump on,
VDDA = 2.7 V
–0.05
–
SID282
VCM
Charge-pump on, VDDA = 2.7 V
-0.05
–
Document Number: 002-22097 Rev. *B
VDDA-0.2
–
V
VDDA-0.2
Page 20 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 8. CTB Opamp Specifications (continued)
Spec ID#
Parameter
Description
Min
Typ
Max
Units
Details/Conditions
SID283
VOUT_1
power=hi, Iload=10 mA
0.5
–
VDDA
-0.5
VDD = 2.7 V
SID284
VOUT_2
power=hi, Iload=1 mA
0.2
–
VDDA
-0.2
VDDA = 2.7 V
VDDA
-0.2
SID285
VOUT_3
power=med, Iload=1 mA
0.2
–
SID286
VOUT_4
power=lo, Iload=0.1 mA
0.2
–
VDDA
-0.2
SID288
VOS_TR
Offset voltage, trimmed
–1.0
0.5
1.0
SID288A
VOS_TR
Offset voltage, trimmed
–
1
–
SID288B
VOS_TR
Offset voltage, trimmed
–
2
–
SID290
VOS_DR_TR
Offset voltage drift, trimmed
-10
3
10
SID290A
VOS_DR_TR
Offset voltage drift, trimmed
–
10
–
SID290B
VOS_DR_TR
Offset voltage drift, trimmed
–
10
–
SID291
CMRR
DC
70
80
–
V
VDDA = 2.7 V
High mode, input 0 V
to VDDA-0.2 V
mV
PSRR
Medium mode, input
0 V to VDDA-0.2 V
Low mode, input 0 V
to VDDA-0.2 V
µV/C
µV/C
High mode
Medium mode
Low mode
Input is 0 V to
VDDA-0.2 V, Output is
0.2 V to VDDA-0.2 V
dB
SID292
VDDA = 2.7 V
At 1 kHz, 10-mV ripple
70
85
–
VDDD = 3.6 V,
high-power mode,
input is 0.2 V to
VDDA-0.2 V
Noise
SID294
VN2
Input-referred, 1 kHz, power=Hi
–
72
–
Input and output are
at 0.2 V to VDDA-0.2 V
SID295
VN3
Input-referred, 10 kHz, power=Hi
–
28
–
nV/rtH Input and output are
at 0.2 V to VDDA-0.2 V
z
SID296
VN4
Input-referred, 100 kHz, power=Hi
–
15
–
Input and output are
at 0.2 V to VDDA-0.2 V
SID297
CLOAD
Stable up to max. load. Performance
specs at 50 pF.
–
–
125
pF
–
SID298
SLEW_RATE
CLOAD = 50 pF, Power = High, VDDA
= 2.7 V
6
–
–
V/µs
–
SID299
T_OP_WAKE
From disable to enable, no external
RC dominating
–
–
25
µs
–
SID299A
OL_GAIN
Open Loop Gain
–
90
–
dB
Document Number: 002-22097 Rev. *B
Page 21 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 8. CTB Opamp Specifications (continued)
Spec ID#
Parameter
Description
Min
Typ
Max
Units
Details/Conditions
COMP_MODE
Comparator mode; 50-mV drive, Trise=Tfall (approx)
SID300
TPD1
Response time; power=hi
–
150
175
SID301
TPD2
Response time; power=med
–
500
–
SID302
TPD3
Response time; power=lo
–
2500
–
SID303
VHYST_OP
Hysteresis
–
10
–
mV
–
SID304
WUP_CTB
Wake-up time from Enabled to
Usable
–
–
25
µs
–
Opamp Deep
Sleep Mode
Mode 2 is lowest current range. Mode 1 has higher GBW.
SID_DS_1
IDD_HI_M1
Mode 1, High current
–
1400
–
SID_DS_2
IDD_MED_M1
Mode 1, Medium current
–
700
–
SID_DS_3
IDD_LOW_M1
Mode 1, Low current
–
200
–
SID_DS_4
IDD_HI_M2
Mode 2, High current
–
120
–
SID_DS_5
IDD_MED_M2
Mode 2, Medium current
–
60
–
SID_DS_6
IDD_LOW_M2
Mode 2, Low current
–
15
–
SID_DS_7
GBW_HI_M1
Mode 1, High current
–
4
–
20-pF load, no DC
load
0.2 V to VDDA-0.2 V
SID_DS_8
GBW_MED_M1
Mode 1, Medium current
–
2
–
20-pF load, no DC
load 0.2 V to
VDDA-0.2 V
SID_DS_9
GBW_LOW_M1
Mode 1, Low current
–
0.5
–
20-pF load, no DC
load 0.2 V to
VDDA-0.2 V
Input is 0.2 V to
VDDA-0.2 V
ns
Input is 0.2 V to
VDDA-0.2 V
Input is 0.2 V to
VDDA-0.2 V
µA
µA
MHz
SID_DS_10 GBW_HI_M2
Mode 2, High current
–
0.5
–
20-pF load, no DC
load 0.2 V to
VDDA-0.2 V
SID_DS_11 GBW_MED_M2
Mode 2, Medium current
–
0.2
–
20-pF load, no DC
load 0.2 V to
VDDAA-0.2 V
SID_DS_12 GBW_Low_M2
Mode 2, Low current
–
0.1
–
20-pF load, no DC
load 0.2 V to
VDDA-0.2 V
Document Number: 002-22097 Rev. *B
Page 22 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 8. CTB Opamp Specifications (continued)
Spec ID#
Parameter
Description
Min
Typ
Max
Units
Details/Conditions
SID_DS_13 VOS_HI_M1
Mode 1, High current
–
5
–
With trim 25 °C, 0.2 V
to VDDA-1.5 V
SID_DS_14 VOS_MED_M1
Mode 1, Medium current
–
5
–
With trim 25 °C, 0.2 V
to VDDA-1.5 V
SID_DS_15 VOS_LOW_M2
Mode 1, Low current
–
5
–
With trim 25 °C, 0.2 V
to VDDA-1.5 V
SID_DS_16 VOS_HI_M2
Mode 2, High current
–
5
–
With trim 25 °C, 0.2V
to VDDA-1.5 V
SID_DS_17 VOS_MED_M2
Mode 2, Medium current
–
5
–
With trim 25 °C, 0.2 V
to VDDA-1.5 V
SID_DS_18 VOS_LOW_M2
Mode 2, Low current
–
5
–
With trim 25 °C, 0.2 V
to VDDA-1.5 V
SID_DS_19 IOUT_HI_M1
Mode 1, High current
–
10
–
Output is 0.5 V to
VDDA-0.5 V
SID_DS_20 IOUT_MED_M1
Mode 1, Medium current
–
10
–
Output is 0.5 V to
VDDA-0.5 V
SID_DS_21 IOUT_LOW_M1
Mode 1, Low current
–
4
–
SID_DS_22 IOUT_HI_M2
Mode 2, High current
–
1
–
–
SID_DS_23 IOU_MED_M2
Mode 2, Medium current
–
1
–
–
SID_DS_24 IOU_LOW_M2
Mode 2, Low current
–
0.5
–
–
Min
Typ
Max
Units
Gain Values are 2,4,16, and 32.
2
–
32
–
Gain Error for Low range; Gain = 2
–
1
–
%
Gain Error for Medium range; Gain = 2
–
–
1.5
%
Gain Error for High range; Gain = 2
–
–
1.5
%
Gain Error for Low range; Gain = 4
–
1
–
%
Gain Error for Medium range; Gain = 4
–
–
1.5
%
Gain Error for High range; Gain = 4
–
–
1.5
%
Gain Error for Low range; Gain = 16
–
3
–
%
Gain Error for Medium range; Gain =
16
–
3
–
%
Gain Error for High range; Gain = 16
–
3
–
%
mV
mA
Output is 0.5 V to
VDDA-0.5 V
Table 9. PGA Specifications
Spec ID#
PGA Gain
Values
Parameter
–
SID_PGA_1 PGA_ERR_1
SID_PGA_2 PGA_ERR_2
SID_PGA_3 PGA_ERR_3
SID_PGA_4 PGA_ERR_4
Description
Gain Error for Low range; Gain = 32
–
5
–
%
Gain Error for Medium range; Gain =
32
–
5
–
%
Gain Error for High range; Gain = 32
–
5
–
%
Details/Conditions
Note
6. Guaranteed by characterization.
Document Number: 002-22097 Rev. *B
Page 23 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 10. Voltage DAC Specifications
(Voltage DAC Specs valid for VDDA ≥ 2.7 V)
Spec ID#
Parameter
Description
Min
Typ
Max
Units
–
+5,–6
–
–
+3.5,
–0.75
–
0.01
–
VDDA-0.01
V
Details/Conditions
13-bit DAC
SID_DAC_1
INL_VDAC1
Integral non linearity (INL)
Differential non linearity (DNL)
LSB
SID_DAC_2
DNL_VDAC1
SID_DAC_3
VOUT_VDAC1 Output voltage range
SID_DAC_4
VOS_VDAC1
Zero scale error (output with all
zeroes input)
–
5
–
mV
Zero scale is at analog
ground
SID_DAC_5
GE_VDAC1
Full scale error less offset
–
–
0.4
%
–
SID_DAC_6
IDD_VDAC1
Block current
–
2.5
–
mA
–
SID_DAC_7
PSRR_VDAC1 Power supply rejection ratio
–
60
–
dB
–
SID_DAC_8
WUP_VDAC1
Wake-up time from Enabled to
Usable
–
25
–
µs
SID_DAC_9
TS_VDAC1
Settling time for DAC
–
–
2
µs
Document Number: 002-22097 Rev. *B
Valid output range is 100
LSBs from rails. Full settling bandwidth to within
100 mV of rail.
For 500-Ksps operation
–
Page 24 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 11. Comparator DC Specifications
Spec ID#
Parameter
Description
Min
Typ
Max
Details/
Conditions
Units
SID84
VOFFSET1
Input offset voltage, Factory trim
–
–
±10
SID85
VOFFSET2
Input offset voltage, Custom trim
–
–
±4
SID86
VHYST
Hysteresis when enabled
–
10
35
SID87
VICM1
Input common mode voltage in normal
mode
0
–
VDDD-0.1
SID247
VICM2
Input common mode voltage in low
power mode
0
–
VDDD
SID247A
VICM3
Input common mode voltage in ultra low
power mode
0
–
VDDD-1.15
SID88
CMRR
Common mode rejection ratio
50
–
–
SID88A
CMRR
Common mode rejection ratio
42
–
–
SID89
ICMP1
Block current, normal mode
–
–
400
–
SID248
ICMP2
Block current, low power mode
–
–
100
–
SID259
ICMP3
Block current in ultra low-power mode
–
–
28
SID90
ZCMP
DC Input impedance of comparator
35
–
–
Min
Typ
Max
Response time, normal mode, 50 mV
overdrive
–
38
110
TRESP2
Response time, low power mode, 50 mV
overdrive
–
TRESP3
Response time, ultra-low power mode,
200 mV overdrive
–
mV
–
–
Modes 1 and 2
V
dB
–
VDDD ≥ 2.2 V for
Temp < 0 °C, VDDD
≥ 1.8 V for Temp >
0 °C
VDDD ≥ 2.7V
VDDD ≤ 2.7V
µA
VDDD ≥ 2.2 V for
Temp < 0 °C, VDDD
≥ 1.8 V for Temp >
0 °C
MΩ
–
Table 12. Comparator AC Specifications
Spec ID#
SID91
SID258
SID92
Parameter
TRESP1
Description
Units
Details/
Conditions
All VDD
ns
–
70
2.3
200
–
15
µs
VDDD ≥ 2.2 V for
Temp < 0 °C, VDDD
≥ 1.8 V for Temp >
0 °C
Details /
Conditions
Table 13. Temperature Sensor Specifications
Spec ID#
SID93
Parameter
TSENSACC
Description
Temperature sensor accuracy
Document Number: 002-22097 Rev. *B
Min
Typ
Max
Units
–5
±1
5
°C
–40 to +85 °C
Page 25 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 14. SAR Specifications
Spec ID#
Parameter
Description
Min
Typ
Max
Units
bits
Details/
Conditions
SAR ADC DC Specifications
SID94
A_RES
Resolution
–
–
12
SID95
A_CHNLS_S
Number of channels - single ended
–
–
8
SID96
A-CHNKS_D
Number of channels - differential
–
–
4
SID97
A-MONO
Monotonicity
–
–
–
SID98
A_GAINERR
Gain error
–
–
±0.1
%
With external
reference.
SID99
A_OFFSET
Input offset voltage
–
–
2
mV
Measured with 1-V
reference
8 full speed.
Yes.
SID100
A_ISAR
Current consumption
–
–
1
mA
SID101
A_VINS
Input voltage range - single ended
VSS
–
VDDA
V
SID102
A_VIND
Input voltage range - differential[
VSS
–
VDDA
V
SID103
A_INRES
Input resistance
–
–
2.2
KΩ
SID104
A_INCAP
Input capacitance
–
–
10
pF
SID260
VREFSAR
Trimmed internal reference to SAR
–
–
TBD
V
Power supply rejection ratio
70
–
–
dB
SAR ADC AC Specifications
SID106
A_PSRR
SID107
A_CMRR
Common mode rejection ratio
66
–
–
dB
SID108
A_SAMP
Sample rate
–
–
1
Msps
SID109
A_SNR
Signal-to-noise and distortion ratio
(SINAD)
65
–
–
dB
SID110
A_BW
Input bandwidth without aliasing
–
–
A_samp/2
kHz
SID111
A_INL
Integral non linearity. VDD = 1.71 to 5.5, –1.7
1 Msps
–
2
LSB
VREF = 1 to VDD
SID111A
A_INL
Integral non linearity. VDDD = 1.71 to 3.6, –1.5
1 Msps
–
1.7
LSB
VREF = 1.71 to VDD
SID111B
A_INL
Integral non linearity. VDD = 1.71 to 5.5, –1.5
500 ksps
–
1.7
LSB
VREF = 1 to VDD
SID112
A_DNL
Differential non linearity. VDD = 1.71 to
5.5, 1 Msps
–1
2.2
LSB
VREF = 1 to VDD
SID112A
A_DNL
Differential non linearity. VDD = 1.71 to
3.6, 1 Msps
–1
2
LSB
VREF = 1.71 to VDD
SID112B
A_DNL
Differential non linearity. VDD = 1.71 to
5.5, 500 ksps
–1
2.2
LSB
VREF = 1 to VDD
SID113
A_THD
Total harmonic distortion
–
–
–65
dB
SID261
FSARINTREF
SAR operating speed without external
ref. bypass
–
–
100
ksps
Document Number: 002-22097 Rev. *B
–
–
–
Measured at 1 V
FIN = 10 kHz
FIN = 10 kHz
12-bit resolution
Page 26 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 15. CapSense and IDAC Specifications[7]
Spec ID#
Parameter
Description
Min
Typ
Max
Units
SYS.PER#3
VDD_RIPPLE
Max allowed ripple on power supply,
DC to 10 MHz
–
–
±50
mV
SYS.PER#16
VDD_RIPPLE_1.8 Max allowed ripple on power supply,
DC to 10 MHz
–
–
±25
mV
4000
µA
V
µA
SID.CSD.BLK ICSD
Maximum block current
SID.CSD#15
Voltage reference for CSD and
Comparator
External Voltage reference for CSD and
Comparator
IDAC1 (7 bits) block current
VREF
SID.CSD#15A VREF_EXT
SID.CSD#16
IDAC1IDD
0.6
1.2
–
–
VDDA 0.6
VDDA 0.6
1750
0.6
V
Details /
Conditions
VDD > 2 V (with
ripple), 25 °C TA,
Sensitivity = 0.1pF
VDD > 1.75 V (with
ripple), 25 °C TA,
Parasitic Capacitance (CP) < 20 pF,
Sensitivity ≥ 0.4 pF
VDDA - 0.6 or 4.4,
whichever is lower
VDDA - 0.6 or 4.4,
whichever is lower
SID.CSD#17
IDAC2IDD
IDAC2 (7 bits) block current
–
–
1750
µA
SID308
VCSD
Voltage range of operation
1.71
–
5.5
V
SID308A
VCOMPIDAC
Voltage compliance range of IDAC
0.6
–
V
SID309
IDAC1DNL
DNL
–1
–
VDDA
–0.6
1
LSB
SID310
IDAC1INL
INL
–3
–
3
LSB
SID311
IDAC2DNL
DNL
–1
–
1.0
LSB
SID312
IDAC2INL
INL
–3
–
3
LSB
SID313
SNR
Ratio of counts of finger to noise.
Guaranteed by characterization
5.0
–
–
SID314
IDAC7_SRC1
4.2
5.4
SID314A
IDAC7_SRC2
34
41
µA
LSB = 300 nA typ.
SID314B
IDAC7_SRC3
275
330
µA
LSB = 2.4 µA typ.
SID314C
IDAC7_SRC4
8
10.5
µA
SID314D
IDAC7_SRC5
69
82
µA
SID314E
IDAC7_SRC6
540
660
µA
SID315
IDAC7_SINK_1
4.2
5.7
µA
LSB = 37.5 nA typ.
2X output stage
LSB = 300 nA typ.
2X output stage
LSB = 2.4 µA typ.2X
output stage
LSB = 37.5 nA typ.
SID315A
IDAC7_SINK_2
34
44
µA
LSB = 300 nA typ.
SID315B
IDAC7_SINK_3
260
340
µA
LSB = 2.4 µA typ.
SID315C
IDAC7_SINK_4
Maximum Source current of 7-bit IDAC
in low range
Maximum Source current of 7-bit IDAC
in medium range
Maximum Source current of 7-bit IDAC
in high range
Maximum Source current of 7-bit IDAC
in low range, 2X mode
Maximum Source current of 7-bit IDAC
in medium range, 2X mode
Maximum Source current of 7-bit IDAC
in high range, 2X mode
Maximum Sink current of 7-bit IDAC in
low range
Maximum Sink current of 7-bit IDAC in
medium range
Maximum Sink current of 7-bit IDAC in
high range
Maximum Sink current of 7-bit IDAC in
low range, 2X mode
Ratio Capacitance range
of 5 to 200 pF,
0.1 pF sensitivity. All
use cases. VDDA >
2 V.
µA LSB = 37.5 nA typ.
8
11.5
µA
LSB = 37.5 nA typ.
2X output stage
1.8 V ±5% or 1.8 V
to 5.5 V
VDDA –0.6 or 4.4,
whichever is lower
Note
7. For optimal CapSense performance, Ports 0, 4, and 5 must be used for large DC loads.
Document Number: 002-22097 Rev. *B
Page 27 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 15. CapSense and IDAC Specifications[7] (continued)
Spec ID#
Parameter
IDAC7_SINK_5
SID315E
IDAC7_SINK_6
SID315F
IDAC8_SRC_1
SID315G
IDAC8_SRC_2
SID315H
IDAC8_SRC_3
SID315J
IDAC8_SINK_1
SID315K
IDAC8_SINK_2
SID315L
IDAC8_SINK_3
SID320
IDACOFFSET1
SID320A
IDACOFFSET2
Maximum Sink current of 7-bit IDAC in
medium range, 2X mode
Maximum Sink current of 7-bit IDAC in
high range, 2X mode
Maximum Source current of 8-bit IDAC
in low range
Maximum Source current of 8-bit IDAC
in medium range
Maximum Source current of 8-bit IDAC
in high range
Maximum Sink current of 8-bit IDAC in
low range
Maximum Sink current of 8-bit IDAC in
medium range
Maximum Sink current of 8-bit IDAC in
high range
All zeroes input; Medium and High
range
All zeroes input; Low range
SID321
IDACGAIN
Full-scale error less offset
SID322
SID323
IDACMISMATCH1 Mismatch between IDAC1 and IDAC2
in Low mode
IDACMISMATCH2 Mismatch between IDAC1 and IDAC2
in Medium mode
IDACMISMATCH3 Mismatch between IDAC1 and IDAC2
in High mode
IDACSET8
Settling time to 0.5 LSB for 8-bit IDAC
SID324
IDACSET7
SID325
CMOD
SID322B
Units
68
86
µA
540
700
µA
8.4
10.8
µA
Details /
Conditions
LSB = 300 nA typ.
2X output stage
LSB = 2.4 µA typ.2X
output stage
LSB = 37.5 nA typ.
68
82
µA
LSB = 300 nA typ.
550
680
µA
LSB = 2.4 µA typ.
8.4
11.4
µA
LSB = 37.5 nA typ.
68
88
µA
LSB = 300 nA typ.
540
670
µA
LSB = 2.4 µA typ.
Min
SID315D
SID322A
Max
Description
Typ
–
–
1
LSB
Polarity set by
Source or Sink
Polarity set by
Source or Sink
–
–
2
LSB
–
–
±20
%
–
–
9.2
LSB
LSB = 37.5 nA typ.
–
–
6
LSB
LSB = 300 nA typ.
–
–
6.8
LSB
LSB = 2.4 µA typ.
–
–
10
µs
Settling time to 0.5 LSB for 7-bit IDAC
–
–
10
µs
External modulator capacitor.
–
2.2
–
nF
Full-scale transition.
No external load.
Full-scale transition.
No external load.
5-V rating, X7R or
NP0 cap.
Table 16. 10-bit CapSense ADC Specifications
Spec ID#
Parameter
Description
Min
Typ
Max
Units
bits
SIDA94
A_RES
Resolution
–
–
10
SID95
A_CHNLS_S
Number of channels - single-ended
–
–
16
SIDA97
A-MONO
Monotonicity
–
–
–
Yes
SIDA98
A_GAINERR
Gain error
–
–
TBD
%
SIDA99
A_OFFSET
Input offset voltage
–
–
TBD
mV
SIDA100
A_ISAR
Current consumption
–
–
TBD
mA
SIDA101
A_VINS
Input voltage range - single-ended
VSSA
–
VDDA
V
2.2
–
KΩ
20
–
pF
SIDA103
A_INRES
Input resistance
–
SIDA104
A_INCAP
Input capacitance
–
Document Number: 002-22097 Rev. *B
Details/Conditions
8 full speed.
Diff inputs use
neighboring I/O
Yes
With external
reference.
Measured with 1-V
reference
Page 28 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 16. 10-bit CapSense ADC Specifications
Spec ID#
Parameter
Description
Min
Typ
Max
Units
Details/Conditions
SIDA106
A_PSRR
Power supply rejection ratio
TBD
–
–
dB
SIDA107
A_TACQ
Sample acquisition time
–
1
–
µs
SIDA108
A_CONV8
Conversion time for 8-bit resolution at
conversion rate = Fhclk/(2^(N+2)). Clock
frequency = 48 MHz.
–
–
21.3
µs
Does not include
acquisition time.
Equivalent to 44.8 ksps
including acquisition
time
SIDA108A
A_CONV10
Conversion time for 10-bit resolution at
conversion rate = Fhclk/(2^(N+2)). Clock
frequency = 48 MHz.
–
–
85.3
µs
Does not include
acquisition time.
Equivalent to 11.6 ksps
including acquisition
time.
SIDA109
A_SND
Signal-to-noise and distortion ratio (SINAD)
TBD
–
–
dB
SIDA110
A_BW
Input bandwidth without aliasing
–
–
22.4
kHz
8-bit resolution
SIDA111
A_INL
Integral non linearity. VDD = 1.71 to 5.5,
1 ksps
–
–
2
LSB
VREF = 2.4 V or greater
SIDA112
A_DNL
Differential non linearity. VDD = 1.71 to 5.5,
1 ksps
–
–
1
LSB
Document Number: 002-22097 Rev. *B
Page 29 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Digital Peripherals
Timer Counter Pulse-Width Modulator (TCPWM)
Table 17. TCPWM Specifications
Spec ID
SID.TCPWM.1
Parameter
ITCPWM1
Description
Block current consumption at 3 MHz
Min
–
Typ
–
Max
45
Units
Details/Conditions
All modes (TCPWM)
SID.TCPWM.2
ITCPWM2
Block current consumption at 12 MHz
–
–
155
μA
All modes (TCPWM)
SID.TCPWM.2A ITCPWM3
Block current consumption at 48 MHz
–
–
650
–
–
Fc
2/Fc
–
–
For all trigger events[8]
Minimum possible
width of Overflow,
Underflow, and CC
(Counter equals
Compare value)
outputs
SID.TCPWM.3
TCPWMFREQ
Operating frequency
SID.TCPWM.4
TPWMENEXT
Input trigger pulse width
SID.TCPWM.5
TPWMEXT
All modes (TCPWM)
MHz
Fc max = CLK_SYS
Maximum = 48 MHz
Output trigger pulse widths
2/Fc
–
–
SID.TCPWM.5A TCRES
Resolution of counter
1/Fc
–
–
SID.TCPWM.5B PWMRES
PWM resolution
1/Fc
–
–
Minimum pulse width
of PWM Output
SID.TCPWM.5C QRES
Quadrature inputs resolution
1/Fc
–
–
Minimum pulse width
between Quadrature
phase inputs
ns
Minimum time
between successive
counts
I2C
Table 18. Fixed I2C DC Specifications[9]
Description
Min
Typ
Max
SID149
Spec ID
II2C1
Block current consumption at 100 kHz
–
–
50
SID150
II2C2
Block current consumption at 400 kHz
–
–
135
SID151
II2C3
Block current consumption at 1 Mbps
–
–
310
II2C4
I2C
–
–
1.4
Min
Typ
Max
Units
Details/Conditions
–
–
1
Msps
–
Min
Typ
Max
Units
Details/Conditions
SID152
Parameter
enabled in Deep Sleep mode
Units
Details/Conditions
–
µA
–
–
Table 19. Fixed I2C AC Specifications[9]
Spec ID
SID153
Parameter
FI2C1
Description
Bit rate
Table 20. SPI DC Specifications[10]
Spec ID
Parameter
Description
SID163
ISPI1
Block current consumption at
1 Mbits/sec
–
–
360
SID164
ISPI2
Block current consumption at
4 Mbits/sec
–
–
560
SID165
ISPI3
Block current consumption at
8 Mbits/sec
–
–
600
–
µA
–
–
Note
8. Trigger events can be Stop, Start, Reload, Count, Capture, or Kill depending on which mode of operation is selected.
9. Guaranteed by characterization.
Document Number: 002-22097 Rev. *B
Page 30 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 21. SPI AC Specifications[10]
Spec ID
SID166
Parameter
FSPI
Description
Min
Typ
Max
SPI Operating frequency (Master; 6X
Oversampling)
–
–
8
Units
Details/Conditions
MHz SID166
Fixed SPI Master Mode AC Specifications
SID167
TDMO
MOSI Valid after SClock driving edge
–
–
15
–
SID168
TDSI
MISO Valid before SClock capturing
edge
20
–
–
SID169
THMO
Previous MOSI data hold time
0
–
–
Referred to Slave capturing
edge
–
ns
Full clock, late MISO
sampling
Fixed SPI Slave Mode AC Specifications
SID170
TDMI
MOSI Valid before Sclock Capturing
edge
40
–
–
SID171
TDSO
MISO Valid after Sclock driving edge
–
–
42 +
3*Tscb
SID171A
TDSO_EXT
MISO Valid after Sclock driving edge
in Ext. Clk mode
–
–
48
–
SID172
THSO
Previous MISO data hold time
0
–
–
–
Min
Typ
Max
Units
Details/Conditions
ns
Tscb = SCB clock
Table 22. UART DC Specifications[10]
Spec ID
Parameter
Description
SID160
IUART1
Block current consumption at
100 Kbits/sec
–
–
55
µA
–
SID161
IUART2
Block current consumption at
1000 Kbits/sec
–
–
312
µA
–
Min
Typ
Max
Units
Details/Conditions
–
–
1
Mbps
–
Table 23. UART AC Specifications[10]
Spec ID
SID162
Parameter
FUART
Description
Bit rate
Table 24. LCD Direct Drive DC Specifications[10]
Spec ID
Parameter
Description
Min
SID154
ILCDLOW
Operating current in low power
mode
–
SID155
CLCDCAP
LCD capacitance per
segment/common driver
–
SID156
LCDOFFSET
Long-term segment offset
–
SID157
ILCDOP1
LCD system operating current
Vbias = 5 V
–
LCD system operating current
Vbias = 3.3 V
–
SID158
ILCDOP2
Typ
Max
Units
Details/Conditions
5
–
µA
16 4 small segment disp. at Hz
500
5000
pF
–
20
–
mV
–
2
–
32 4 segments. 50 Hz. 25 °C
mA
32 4 segments. 50 Hz. 25 °C 4
segments. 50 Hz. 25 °C
2
–
Min
Typ
Max
Units
Details/Conditions
10
50
150
Hz
–
Table 25. LCD Direct Drive AC Specifications[10]
Spec ID
SID159
Parameter
FLCD
Description
LCD frame rate
Note
10. Guaranteed by characterization.
Document Number: 002-22097 Rev. *B
Page 31 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Memory
Table 26. Flash DC Specifications
Spec ID
SID173
Parameter
VPE
Description
Min
Typ
Max
Units
Details/Conditions
1.71
–
5.5
V
–
Description
Min
Typ
Max
Units
Details/Conditions
Erase and program voltage
Table 27. Flash AC Specifications
Spec ID
Parameter
SID174
TROWWRITE[11]
Row (block) write time (erase and
program)
–
–
20
SID175
TROWERASE[11]
Row erase time
–
–
13
SID176
Row program time after erase
–
–
7
–
Bulk erase time (16 KB)
–
–
15
–
SID180
TROWPROGRAM[11]
TBULKERASE[11]
TDEVPROG[11]
SID181[12]
FEND
Flash endurance
SID182[12]
FRET
SID178
[12]
SID182A[12]
SID182B
–
FRETQ
Total device program time
Row (block) = 64 bytes
ms
–
–
–
7.5
Seconds
–
100 K
–
–
Cycles
–
Flash retention. TA 55 °C, 100 K
P/E cycles
20
–
–
Flash retention. TA 85 °C, 10 K
P/E cycles
10
–
–
Flash retention. TA 105 °C, 10 K
P/E cycles, three years at TA
85 °C
10
–
20
–
Years
–
years
Guaranteed by characterization
SID256
TWS48
Number of Wait states at 48 MHz
2
–
–
CPU execution from
Flash
SID257
TWS24
Number of Wait states at 24 MHz
1
–
–
CPU execution from
Flash
Min
Typ
Max
Units
1
–
67
V/ms
V
System Resources
Power-on Reset (POR)
Table 28. Power On Reset (PRES)
Spec ID
Parameter
Description
SID.CLK#6 SR_POWER_UP Power supply slew rate
Details/Conditions
At power-up
[12]
VRISEIPOR
Rising trip voltage
0.80
–
1.5
[12]
VFALLIPOR
Falling trip voltage
0.70
–
1.4
Min
Typ
Max
Units
Details/Conditions
V
–
SID185
SID186
–
–
Table 29. Brown-out Detect (BOD) for VCCD
Spec ID
Parameter
Description
SID190[12]
VFALLPPOR
BOD trip voltage in active and
sleep modes
1.48
–
1.62
SID192[12]
VFALLDPSLP
BOD trip voltage in Deep Sleep
1.1
–
1.5
–
Notes
11. It can take as much as 20 milliseconds to write to Flash. During this time the device should not be Reset, or Flash operations will be interrupted and cannot be relied
on to have completed. Reset sources include the XRES pin, software resets, CPU lockup states and privilege violations, improper power supply levels, and watchdogs.
Make certain that these are not inadvertently activated.
12. Guaranteed by characterization.
Document Number: 002-22097 Rev. *B
Page 32 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
SWD Interface
Table 30. SWD Interface Specifications
Spec ID
Parameter
Description
Min
Typ
Max
Units
Details/Conditions
SWDCLK ≤ 1/3 CPU
clock frequency
SID213
F_SWDCLK1
3.3 V VDD 5.5 V
–
–
14
SID214
F_SWDCLK2
1.71 V VDD 3.3 V
–
–
7
SWDCLK ≤ 1/3 CPU
clock frequency
SID215[13]
T_SWDI_SETUP T = 1/f SWDCLK
0.25*T
–
–
–
T_SWDI_HOLD
0.25*T
–
–
T_SWDO_VALID T = 1/f SWDCLK
–
–
0.5*T
T_SWDO_HOLD T = 1/f SWDCLK
1
–
–
Min
Typ
Max
Units
Details/Conditions
MHz
[13]
SID216
[13]
SID217
[13]
SID217A
T = 1/f SWDCLK
ns
–
–
–
Internal Main Oscillator
Table 31. IMO DC Specifications
(Guaranteed by Design)
Spec ID
Parameter
Description
SID218
IIMO1
IMO operating current at 48 MHz
–
–
250
µA
–
SID219
IIMO2
IMO operating current at 24 MHz
–
–
180
µA
–
Min
Typ
Max
Units
Details/Conditions
Table 32. IMO AC Specifications
Spec ID
Parameter
Description
SID223
FIMOTOL1
Frequency range from 24 to
48 MHz (4-MHz increments)
–2
–
+2
%
2 V VDD 5.5 V, and
–25 °C TA 85 °C
SID226
TSTARTIMO
IMO startup time
–
–
7
µs
–
SID228
TJITRMSIMO2
RMS jitter at 24 MHz
–
145
–
ps
–
Min
Typ
Max
Units
Details/Conditions
–
0.3
1.05
µA
–
Min
Typ
Max
Units
Details/Conditions
Internal Low-Speed Oscillator
Table 33. ILO DC Specifications
(Guaranteed by Design)
Spec ID
Parameter
SID231[13] IILO1
Description
ILO operating current
Table 34. ILO AC Specifications
Spec ID
[13]
SID234
Parameter
TSTARTILO1
Description
ILO startup time
–
–
2
ms
–
SID236[13] TILODUTY
ILO duty cycle
40
50
60
%
–
SID237
ILO frequency range
20
40
80
kHz
–
FILOTRIM1
Note
13. Guaranteed by characterization.
Document Number: 002-22097 Rev. *B
Page 33 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Table 35. Watch Crystal Oscillator (WCO) Specifications
Spec ID#
Parameter
Description
Min
Typ
Max
Units
SID398
FWCO
Crystal Frequency
–
32.768
–
kHz
SID399
FTOL
Frequency tolerance
–
50
250
ppm
Details / Conditions
With 20-ppm crystal
SID400
ESR
Equivalent series resistance
–
50
–
kΩ
SID401
PD
Drive Level
–
–
1
µW
SID402
TSTART
Startup time
–
–
500
ms
SID403
CL
Crystal Load Capacitance
6
–
12.5
pF
SID404
C0
Crystal Shunt Capacitance
–
1.35
–
pF
SID405
IWCO1
Operating Current (high power mode)
–
–
8
µA
Min
Typ
Max
Units
Details/Conditions
Table 36. External Clock Specifications
Spec ID
SID305[14]
Parameter
Description
ExtClkFreq
External clock input frequency
0
–
16
MHz
–
SID306[14] ExtClkDuty
Duty cycle; measured at VDD/2
45
–
55
%
–
Min
Typ
Max
Units
Details/Conditions
3
–
4
Periods
–
Min
Typ
Max
Units
–
–
1.6
ns
Table 37. Block Specs
Spec ID
SID262[14]
Parameter
TCLKSWITCH
Description
System clock source switching time
Table 38. PRGIO Pass-through Time (Delay in Bypass Mode)
Spec ID#
SID252
Parameter
Description
PRG_BYPASS Max. delay added by PRGIO in bypass
mode
Details / Conditions
Note
14. Guaranteed by characterization.
Document Number: 002-22097 Rev. *B
Page 34 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Ordering Information
DMA
Flash (KB)
SRAM (KB)
13-bit VDAC
Opamp (CTB)
CapSense
10-bit CSD ADC
Direct LCD Drive
RTC
12-bit SAR ADC
LP Comparators
TCPWM Blocks
SCB Blocks
Smart IOs
GPIO
28-SSOP
45-WLCSP
48-TQFP
48-QFN
CY8C4125PVI-PS421
24
✔
32
4
2
4
–
✔
✔
✔
806 ksps
2
8
2
8
20
✔
–
–
–
CY8C4125FNI-PS423
24
✔
32
4
2
4
–
✔
✔
✔
806 ksps
2
8
2
8
37
–
✔
–
–
CY8C4125AZI-PS423
24
✔
32
4
2
4
–
✔
✔
✔
806 ksps
2
8
2
8
38
–
–
✔
–
CY8C4125LQI-PS423
24
✔
32
4
2
4
–
✔
✔
✔
806 ksps
2
8
2
8
38
–
–
–
✔
CY8C4145PVI-PS421
48
✔
32
4
2
4
–
✔
✔
✔
1000 ksps
2
8
2
8
20
✔
–
–
–
CY8C4145FNI-PS423
48
✔
32
4
2
4
–
✔
✔
✔
1000 ksps
2
8
2
8
37
–
✔
–
–
CY8C4145AZI-PS423
48
✔
32
4
2
4
–
✔
✔
✔
1000 ksps
2
8
2
8
38
–
–
✔
–
CY8C4145LQI-PS423
48
✔
32
4
2
4
–
✔
✔
✔
1000 ksps
2
8
2
8
38
–
–
–
✔
CY8C4145PVI-PS431
48
✔
32
4
2
4
✔
✔
✔
✔
1000 ksps
2
8
3
8
20
✔
–
–
–
CY8C4145FNI-PS433
48
✔
32
4
2
4
✔
✔
✔
✔
1000 ksps
2
8
3
8
37
–
✔
–
–
CY8C4145AZI-PS433
48
✔
32
4
2
4
✔
✔
✔
✔
1000 ksps
2
8
3
8
38
–
–
✔
–
CY8C4145LQI-PS433
48
✔
32
4
2
4
✔
✔
✔
✔
1000 ksps
2
8
3
8
38
–
–
–
✔
MPN
Category
4125
4145
Package
Max CPU Speed (MHz)
Features
The nomenclature used in the preceding table is based on the following part numbering convention:
Field
Description
Values
Meaning
CY8C
Cypress Prefix
4
Architecture
4
ARM Cortex-M0+ CPU
A
Family
1
4100PS Family
2
24 MHz
B
Maximum frequency
C
Flash Memory Capacity
DE
Package Code
4
48 MHz
5
32 KB
AZ
TQFP (0.5mm pitch)
LQ
QFN
PV
SSOP
FN
CSP
S
Series Designator
PS
S-Series
F
Temperature Range
I
Industrial
XYZ
Attributes Code
000-999
Code of feature set in the specific family
Document Number: 002-22097 Rev. *B
Page 35 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
The following is an example of a part number:
CY 8 C 4 A B C DE F – S XYZ
Example
Cypress Prefix
Architecture
4 : PSoC 4
1 : 4100 Family
Family within Architecture
CPU Speed
4 : 48 MHz
5 : 32 KB
Flash Capacity
AZ : TQFP
Package Code
I : Industrial
Temperature Range
Series Designator
Attributes Code
Document Number: 002-22097 Rev. *B
Page 36 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Packaging
SPEC ID#
Package
Description
Package DWG #
BID20
48-pin TQFP
7 × 7 × 1.4 mm height with
0.5-mm pitch
51-85135
BID27
48-pin QFN
6 × 6 × 0.6 mm height with
0.4-mm pitch
001-57280
BID34
45-ball WLCSP
3.7 × 2 × 0.5 mm height
with 0.38-mm pitch
002-10531
BID34A
28-pin SSOP 5.3 × 10.2 × 0.65-mm pitch
51-85079
Table 39. Package Thermal Characteristics
Parameter
Description
Package
Min
Typ
Max
Units
TA
Operating Ambient temperature
–40
25
105
°C
TJ
Operating junction temperature
–40
–
125
°C
TJA
Package θJA
48-pin TQFP
–
71
–
°C/Watt
TJC
Package θJC
48-pin TQFP
–
34.3
–
°C/Watt
TJA
Package θJA
48-pin QFN
–
18
–
°C/Watt
TJC
Package θJC
48-pin QFN
–
4.5
–
°C/Watt
TJA
Package θJA
45-Ball WLCSP
–
37.2
–
°C/Watt
TJC
Package θJC
45-Ball WLCSP
–
0.31
–
°C/Watt
TJA
Package θJA
28-pin SSOP
–
60
–
°C/Watt
TJC
Package θJC
28-pin SSOP
–
25
–
°C/Watt
Table 40. Solder Reflow Peak Temperature
Package
Maximum Peak
Temperature
Maximum Time at Peak Temperature
All
260 °C
30 seconds
Table 41. Package Moisture Sensitivity Level (MSL), IPC/JEDEC J-STD-020
Package
MSL
All
MSL 3
Document Number: 002-22097 Rev. *B
Page 37 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Package Diagrams
Figure 7. 48-pin TQFP Package Outline
51-85135 *C
Figure 8. 48-Pin QFN Package Outline
001-57280 *E
Document Number: 002-22097 Rev. *B
Page 38 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Figure 9. 45-Ball WLCSP Dimensions
002-10531 **
Figure 10. 28-Pin SSOP Package Outline
51-85079 *F
Document Number: 002-22097 Rev. *B
Page 39 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Acronyms
Table 42. Acronyms Used in this Document
Acronym
Description
Table 42. Acronyms Used in this Document (continued)
Acronym
Description
ETM
embedded trace macrocell
FIR
finite impulse response, see also IIR
FPB
flash patch and breakpoint
FS
full-speed
GPIO
general-purpose input/output, applies to a PSoC
pin
arithmetic logic unit
HVI
high-voltage interrupt, see also LVI, LVD
analog multiplexer bus
IC
integrated circuit
API
application programming interface
IDAC
current DAC, see also DAC, VDAC
APSR
application program status register
IDE
integrated development environment
ARM®
advanced RISC machine, a CPU architecture
I
ATM
automatic thump mode
BW
bandwidth
CAN
Controller Area Network, a communications
protocol
abus
analog local bus
ADC
analog-to-digital converter
AG
analog global
AHB
AMBA (advanced microcontroller bus
architecture) high-performance bus, an ARM
data transfer bus
ALU
AMUXBUS
2C,
or IIC
Inter-Integrated Circuit, a communications
protocol
IIR
infinite impulse response, see also FIR
ILO
internal low-speed oscillator, see also IMO
IMO
internal main oscillator, see also ILO
integral nonlinearity, see also DNL
CMRR
common-mode rejection ratio
INL
CPU
central processing unit
I/O
input/output, see also GPIO, DIO, SIO, USBIO
CRC
cyclic redundancy check, an error-checking
protocol
IPOR
initial power-on reset
IPSR
interrupt program status register
DAC
digital-to-analog converter, see also IDAC, VDAC
IRQ
interrupt request
DFB
digital filter block
ITM
instrumentation trace macrocell
DIO
digital input/output, GPIO with only digital
capabilities, no analog. See GPIO.
LCD
liquid crystal display
DMIPS
Dhrystone million instructions per second
LIN
Local Interconnect Network, a communications
protocol.
DMA
direct memory access, see also TD
LR
link register
DNL
differential nonlinearity, see also INL
LUT
lookup table
DNU
do not use
LVD
low-voltage detect, see also LVI
DR
port write data registers
LVI
low-voltage interrupt, see also HVI
DSI
digital system interconnect
LVTTL
low-voltage transistor-transistor logic
DWT
data watchpoint and trace
MAC
multiply-accumulate
ECC
error correcting code
MCU
microcontroller unit
ECO
external crystal oscillator
MISO
master-in slave-out
EEPROM
electrically erasable programmable read-only
memory
NC
no connect
EMI
electromagnetic interference
NMI
nonmaskable interrupt
EMIF
external memory interface
NRZ
non-return-to-zero
EOC
end of conversion
NVIC
nested vectored interrupt controller
EOF
end of frame
NVL
nonvolatile latch, see also WOL
EPSR
execution program status register
ESD
electrostatic discharge
Document Number: 002-22097 Rev. *B
opamp
operational amplifier
PAL
programmable array logic, see also PLD
Page 40 of 44
PRELIMINARY
Table 42. Acronyms Used in this Document (continued)
Acronym
Description
PSoC® 4: PSoC 4100PS Datasheet
Table 42. Acronyms Used in this Document (continued)
Acronym
Description
PC
program counter
SWV
single-wire viewer
PCB
printed circuit board
TD
transaction descriptor, see also DMA
PGA
programmable gain amplifier
THD
total harmonic distortion
PHUB
peripheral hub
TIA
transimpedance amplifier
PHY
physical layer
TRM
technical reference manual
PICU
port interrupt control unit
TTL
transistor-transistor logic
PLA
programmable logic array
TX
transmit
PLD
programmable logic device, see also PAL
UART
PLL
phase-locked loop
Universal Asynchronous Transmitter Receiver, a
communications protocol
PMDD
package material declaration data sheet
UDB
universal digital block
POR
power-on reset
PRES
precise power-on reset
PRS
pseudo random sequence
PS
port read data register
PSoC®
Programmable System-on-Chip™
PSRR
power supply rejection ratio
PWM
pulse-width modulator
RAM
random-access memory
RISC
reduced-instruction-set computing
RMS
root-mean-square
RTC
real-time clock
RTL
register transfer language
RTR
remote transmission request
RX
receive
SAR
successive approximation register
SC/CT
switched capacitor/continuous time
SCL
I2C serial clock
SDA
I2C serial data
S/H
sample and hold
SINAD
signal to noise and distortion ratio
SIO
special input/output, GPIO with advanced
features. See GPIO.
SOC
start of conversion
SOF
start of frame
SPI
Serial Peripheral Interface, a communications
protocol
SR
slew rate
SRAM
static random access memory
SRES
software reset
SWD
serial wire debug, a test protocol
Document Number: 002-22097 Rev. *B
USB
Universal Serial Bus
USBIO
USB input/output, PSoC pins used to connect to
a USB port
VDAC
voltage DAC, see also DAC, IDAC
WDT
watchdog timer
WOL
write once latch, see also NVL
WRES
watchdog timer reset
XRES
external reset I/O pin
XTAL
crystal
Page 41 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Document Conventions
Units of Measure
Table 43. Units of Measure
Symbol
Unit of Measure
°C
degrees Celsius
dB
decibel
fF
femto farad
Hz
hertz
KB
1024 bytes
kbps
kilobits per second
Khr
kilohour
kHz
kilohertz
k
kilo ohm
ksps
kilosamples per second
LSB
least significant bit
Mbps
megabits per second
MHz
megahertz
M
mega-ohm
Msps
megasamples per second
µA
microampere
µF
microfarad
µH
microhenry
µs
microsecond
µV
microvolt
µW
microwatt
mA
milliampere
ms
millisecond
mV
millivolt
nA
nanoampere
ns
nanosecond
nV
nanovolt
ohm
pF
picofarad
ppm
parts per million
ps
picosecond
s
second
sps
samples per second
sqrtHz
square root of hertz
V
volt
Document Number: 002-22097 Rev. *B
Page 42 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Revision History
Description Title: PSoC® 4: PSoC 4100PS Datasheet Programmable System-on-Chip (PSoC®)
Document Number: 002-22097
Orig. of Submission
Revision
ECN
Description of Change
Change
Date
**
6049408
WKA
01/30/2018 New spec
*A
6155846
WKA
04/27/2018 Updated number of VDACs to 2.
Updated Voltage DAC Specifications.
*B
6164274
JIAO
05/03/2018 Corrected typo in Ordering Information.
Document Number: 002-22097 Rev. *B
Page 43 of 44
PRELIMINARY
PSoC® 4: PSoC 4100PS Datasheet
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC® Solutions
Products
Arm® Cortex® Microcontrollers
Automotive
cypress.com/arm
cypress.com/automotive
Clocks & Buffers
Interface
Internet of Things
Memory
cypress.com/clocks
cypress.com/interface
cypress.com/iot
cypress.com/memory
Microcontrollers
cypress.com/mcu
PSoC
cypress.com/psoc
Power Management ICs
Touch Sensing
USB Controllers
Wireless Connectivity
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU
Cypress Developer Community
Community | Projects | Video | Blogs | Training | Components
Technical Support
cypress.com/support
cypress.com/pmic
cypress.com/touch
cypress.com/usb
cypress.com/wireless
© Cypress Semiconductor Corporation 2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document, including
any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide.
Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual
property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby
grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and
reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either
directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided
by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the
Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing
device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress does not assume any liability arising out of any security breach,
such as unauthorized access to or use of a Cypress product. In addition, the products described in these materials may contain design defects or errors known as errata which may cause the product
to deviate from published specifications. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any
liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming
code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this
information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons
systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances
management, or other uses where the failure of the device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device
or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you
shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from
and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 002-22097 Rev. *B
Revised May 3, 2018
Page 44 of 44