TLE42644GHTMA1

OPTIREG™ linear TLE42644G Low dropout fi xed voltage regulator Features • Output voltage 5 V ± 2% up to output currents of 50 mA • Output voltage 5 V ± 3% up to output currents of 100 mA • Very low dropout voltage • Very low current consumption: typ. 40 µA • Output current limitation • Reverse polarity protection • Overtemperature shutdown • Wide temperature range from -40°C up to +150°C • Suitable for use in automotive electronics • Green Product (RoHS compliant) Potential applications General automotive applications. Product validation Qualified for automotive applications. Product validation according to AEC-Q100. Description The TLE42644G is a monolithic integrated low dropout fixed voltage regulator for load currents up to 100 mA. It is the 1-to-1 replacement product for the TLE4264-2G. It is functionally compatible to the TLE4264G, but has a reduced quiescent current of typ. 40 µA. The TLE42644G is especially designed for applications requiring very low standby currents, e.g. with a permanent connection to the car’s battery. The device is available in the small surface mounted PG-SOT223-4 package and is pin compatible to the TLE4264-2G and the TLE4264G. The device is designed for the harsh environment of automotive applications. Therefore it is protected against overload, short-circuit and overtemperature conditions by the implemented output current limitation and the overtemperature shutdown circuit. The TLE42644G can be also used in all other applications requiring a stabilized 5 V voltage. An input voltage up to 45 V is regulated to VQ,nom = 5 V with a precision of ±3%. An accuracy of ±2% is achieved for load currents up to 50 mA. Type Package Marking TLE42644G PG-SOT223-4 42644 Datasheet www.infineon.com/OPTIREG-linear 1 Rev. 1.11 2023-08-02 OPTIREG™ linear TLE42644G Low dropout fixed voltage regulator Block diagram 1 Block diagram Saturation Control and Protection Circuit Temperature Sensor Input I Q Control Amplifier Adjustment Output Buffer Bandgap Reference GND GND AEB02870 Figure 1 Datasheet Block diagram 2 Rev. 1.11 2023-08-02 OPTIREG™ linear TLE42644G Low dropout fixed voltage regulator Pin configuration 2 Pin configuration 2.1 Pin assignment PG-SOT223-4 GND 4 1 2 3 I GND Q AEP02868 Figure 2 Pin configuration (top view) 2.2 Pin definitions and functions PG-SOT223-4 Pin no. Symbol Function 1 I Input Block to ground directly at the IC with a ceramic capacitor 2 GND Ground 3 Q Output Block to ground with a capacitor close to the IC terminals, respecting the values given for its capacitance and ESR in “Functional range” on Page 4 4 / Heat slug GND Ground / Heat slug Internally connected to leadframe and GND; connect to GND and heatsink area Datasheet 3 Rev. 1.11 2023-08-02 OPTIREG™ linear TLE42644G Low dropout fixed voltage regulator General product characteristics 3 General product characteristics 3.1 Absolute maximum ratings Table 1 1) Absolute maximum ratings Tj = -40°C to +150°C; all voltages with respect to ground, (unless otherwise specified) Parameter Symbol Values Unit Note or Test Condition Number Min. Typ. Max. VI -30 – 45 V – P_4.1.1 VQ -0.3 – 32 V – P_4.1.2 Junction temperature Tj -40 – 150 °C – P_4.1.3 Storage temperature Tstg -50 – 150 °C – P_4.1.4 ESD absorption VESD,HBM -3 – 3 kV 2) P_4.1.5 ESD absorption VESD,CDM -1500 – 1500 V 3) Input I Voltage Output Q Voltage Temperature ESD susceptibility Human body model (HBM) Charge device P_4.1.6 model (CDM) at all pins 1) not subject to production test, specified by design. 2) ESD susceptibility human body model “HBM” according to AEC-Q100-002 - JESD22-A114. 3) ESD susceptibility charged device model “CDM” according to ESDA STM5.3.1. Notes 1. Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the datasheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous repetitive operation. 3.2 Functional range Table 2 Functional range Parameter Symbol Values Min. Typ. Max. Unit Note or Test Condition Number Input voltage VI 5.5 – 40 V – P_4.2.1 Output capacitor’s requirements for stability CQ 10 – – µF – P_4.2.2 Datasheet 4 Rev. 1.11 2023-08-02 OPTIREG™ linear TLE42644G Low dropout fixed voltage regulator General product characteristics Table 2 Functional range (cont’d) Parameter Symbol Values Min. Typ. Max. Unit Note or Test Condition Number Output capacitor’s requirements for stability ESR(CQ) – – 2 Ω 1) P_4.2.3 Junction temperature Tj -40 – 150 °C – P_4.2.4 1) Relevant ESR value at f = 10 kHz. Note: Within the functional or operating range, the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the Electrical Characteristics table. 3.3 Thermal resistance Note: This thermal data was generated in accordance with JEDEC JESD51 standards. For more information, go to www.jedec.org. Table 3 1) Thermal resistance Parameter Symbol Values Min. Typ. Max. – 17 – Unit Note or Test Condition Number K/W measured to heat slug P_4.3.1 K/W 2) FR4 2s2p board P_4.3.2 TLE42644G (PG-SOT223-4) Junction to case Junction to ambient RthJC RthJA – 54 – Junction to ambient RthJA – 139 – K/W 3) FR4 1s0p board, footprint only P_4.3.3 Junction to ambient RthJA – 73 – K/W 3) FR4 1s0p board, 300 mm2 heatsink area P_4.3.4 Junction to ambient RthJA – 64 – K/W 3) P_4.3.5 FR4 1s0p board, 600 mm2 heatsink area 1) Not subject to production test, specified by design. 2) Specified RthJA value is according to JEDEC JESD51-2,-5,-7 at natural convection on FR4 2s2p board; The product (chip and package) was simulated on a 76.2 × 114.3 × 1.5 mm3 board with 2 inner copper layers (2 × 70 µm Cu, 2 × 35 µm Cu). Where applicable, a thermal via array under the exposed pad contacted the first inner copper layer. 3) Specified RthJA value is according to JEDEC JESD 51-3 at natural convection on FR4 1s0p board; The product (chip and package) was simulated on a 76.2 114.3 × 1.5 mm3 board with 1 copper layer (1 × 70 µm Cu). Datasheet 5 Rev. 1.11 2023-08-02 OPTIREG™ linear TLE42644G Low dropout fixed voltage regulator Electrical characteristics 4 Electrical characteristics 4.1 Electrical characteristics voltage regulator Table 4 Electrical characteristics VI = 13.5 V; Tj = -40°C to +150°C; all voltages with respect to ground (unless otherwise specified) Parameter Symbol Values Min. Typ. Max. Unit Note or Test Condition Number Output Q Output voltage VQ 4.9 5.0 5.1 V 5 mA < IQ< 50 mA 6 V < VI < 16 V P_5.1.1 Output voltage VQ 4.85 5.0 5.15 V 5 mA < IQ