MRF9002NR2

Freescale Semiconductor Technical Data Document Number: MRF9002NR2 Rev. 8, 5/2006 RF Power Field Effect Transistor Array N - Channel Enhancement - Mode Lateral MOSFET Designed for broadband commercial and industrial applications with frequencies to 1000 MHz. The high gain and broadband performance of this device make it ideal for large - signal, common - source amplifier applications in 26 volt base station equipment. The device is in a PFP - 16 Power Flat Pack package which gives excellent thermal performances through a solderable backside contact. • Typical Performance at 960 MHz, 26 Volts Output Power — 2 Watts Per Transistor Power Gain — 18 dB Efficiency — 50% • Capable of Handling 10:1 VSWR, @ 26 Vdc, 960 MHz, 2 Watts CW Output Power Features • Designed for Maximum Gain and Insertion Phase Flatness • Excellent Thermal Stability • Characterized with Series Equivalent Large - Signal Impedance Parameters • RoHS Compliant • In Tape and Reel. R2 Suffix = 1,500 Units per 16 mm, 13 inch Reel. MRF9002NR2 1000 MHz, 2 W, 26 V LATERAL N - CHANNEL BROADBAND RF POWER MOSFET 16 1 CASE 978 - 03 PLASTIC PFP - 16 N.C. N.C. GATE1 N.C. GATE2 N.C. GATE3 N.C. 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 DRAIN 1−1 DRAIN 1−2 DRAIN 2−1 DRAIN 2−2 N.C. DRAIN 3−1 DRAIN 3−2 N.C. (Top View) Note: Exposed backside flag is source terminal for transistors. Table 1. Maximum Ratings Rating Drain - Source Voltage Gate - Source Voltage Total Dissipation Per Transistor @ TC = 25°C Storage Temperature Range Operating Junction Temperature Symbol VDSS VGS PD Tstg TJ Figure 1. Pin Connections Value - 0.5, +65 - 0.5, + 15 4 - 65 to +150 150 Unit Vdc Vdc W °C °C Table 2. Thermal Characteristics Characteristic Thermal Resistance, Junction to Case, Single Transistor Symbol RθJC Value (1) 12 Unit °C/W Table 3. Moisture Sensitivity Level Test Methodology Per JESD 22 - A113, IPC/JEDEC J - STD - 020 Rating 3 Package Peak Temperature 260 Unit °C 1. MTTF calculator available at http://www.freescale.com/rf. Select Tools/Software/Application Software/Calculators to access the MTTF calculators by product. NOTE - CAUTION - MOS devices are susceptible to damage from electrostatic charge. Reasonable precautions in handling and packaging MOS devices should be observed. © Freescale Semiconductor, Inc., 2006. All rights reserved. MRF9002NR2 1 RF Device Data Freescale Semiconductor Table 4. Electrical Characteristics (TC = 25°C unless otherwise noted) Characteristic On Characteristics Gate Threshold Voltage (VDS = 10 Vdc, ID = 20 μAdc) Gate Quiescent Voltage (VDS = 26 Vdc, ID = 25 mAdc) Drain - Source On - Voltage (VGS = 10 Vdc, ID = 0.1 Adc) Common - Source Amplifier Power Gain @ P1dB (VDD = 26 Vdc, IDQ = 25 mA, f = 960.0 MHz) Drain Efficiency @ P1dB (VDD = 26 Vdc, IDQ = 25 mA, f = 960.0 MHz) Input Return Loss @ P1dB (VDD = 26 Vdc, IDQ = 25 mA, f = 960.0 MHz) Power Output, 1 dB Compression Point (VDD = 26 Vdc, IDQ = 25 mA, f = 960.0 MHz) VGS(th) VGS(Q) VDS(on) 2.4 3 — — — 0.3 4 5 — Vdc Vdc Vdc Symbol Min Typ Max Unit Functional Tests (Per Transistor in Freescale Test Fixture, 50 ohm system) Gps η IRL P1dB 15 35 — 34 18 50 - 15 37 — — -9 — dB % dB dBm MRF9002NR2 2 RF Device Data Freescale Semiconductor VGS1 + C7 Z2 C14 R1 Z3 L1 L4 DUT Z4 + C8 Z5 C16 VDS1 RF1 OUTPUT RF1 INPUT Z1 C1 VGS2 Z6 C3 VGS3 Z11 C5 C2 VDS2 + C9 Z7 C13 + C11 Z12 C15 R3 Z13 R2 Z8 L2 L5 Z9 + C10 Z10 C18 + C12 Z14 Z15 C17 RF2 INPUT C4 VDS3 RF2 OUTPUT L3 L6 RF3 INPUT C6 RF3 OUTPUT Figure 2. MRF9002NR2 Broadband Test Circuit Schematic Table 5. MRF9002NR2 Broadband Test Circuit Component Designations and Values Designators C1 - C6 C7 - C12 C13 C14, C15 C16, C17 C18 L1 - L6 R1 - R3 Z1, Z11 Z2, Z7, Z12 Z3, Z8, Z13 Z4, Z14 Z5, Z15 Z6 Z9 Z10 PCB Raw PCB Material Bedstead Description 33 pF Chip Capacitors (0805) 1.0 μF, 35 V Tantalum Capacitors, B Case, Kemet 8.2 pF Chip Capacitor (0805) 10 pF Chip Capacitors (0805) 2.7 pF Chip Capacitors (0805) 3.3 pF Chip Capacitor (0805) 12 nH Chip Inductors (0805) 0 W Chip Resistors (0805) 1.16 x 28.5 mm Microstrip 0.65 x 5.6 mm Microstrip 0.65 x 2.6 mm Microstrip 1.16 x 19.5 mm Microstrip 1.16 x 17.5 mm Microstrip 1.16 x 12.9 mm Microstrip 1.16 x 27.2 mm Microstrip 1.16 x 4.3 mm Microstrip Etched Circuit Board Rogers RO4350, 0.020″, 2.5″, x 2.5″, er = 3.5 Copper Heatsink MRF9002NR2 RF Device Data Freescale Semiconductor 3 RF1 INPUT C1 VGS1 VGS2 C7 C16 C8 RF1 OUTPUT C2 VDS1 VDS2 C10 C9 L1 RF2 INPUT C3 C13 R3 L3 MRF9002 960 MHz Rev. B C11 C15 L6 L2 R2 R1 Pin 1 C14 L4 L5 RF2 OUTPUT C18 C4 C12 C17 VDS3 VGS3 C5 RF3 INPUT C6 RF3 OUTPUT Freescale has begun the transition of marking Printed Circuit Boards (PCBs) with the Freescale Semiconductor signature/logo. PCBs may have either Motorola or Freescale markings during the transition period. These changes will have no impact on form, fit or function of the current product. Figure 3. MRF9002NR2 Broadband Test Circuit Component Layout MRF9002NR2 4 RF Device Data Freescale Semiconductor TYPICAL CHARACTERISTICS 35 33 Pout , OUTPUT POWER (dBm) 31 29 27 25 23 21 19 17 15 0 2 4 6 8 10 12 14 Pin, INPUT POWER (dBm) VDS = 26 Vdc IDQ = 25 mA f = 960 MHz Single−Tone Pout 19.5 19.25 Gps 19 18.75 18.5 18.25 18 17.75 17.5 17.25 17 16 16 15 10 15 20 25 30 Pout, OUTPUT POWER (dBm) G ps , POWER GAIN (dB) G ps , POWER GAIN (dB) 21 20 19 18 17 VDS = 26 Vdc f = 960 MHz Single−Tone 35 40 25 mA 75 mA 50 mA 23 22 100 mA Figure 4. Output Power and Power Gain versus Input Power 20.3 Gps G ps , POWER GAIN (dB) 20.2 −29 −28 −20 −25 −30 −35 −40 −45 −50 −55 Figure 5. Power Gain versus Output Power 20.1 IMD 20 Pout = 2 W (PEP) IDQ = 25 mA f1 = 960.0 MHz, f2 = 960.1 MHz 22 23 24 25 26 27 28 29 30 −30 IMD, INTERMODULATION DISTORTION (dBc) IMD, INTERMODULATION DISTORTION (dBc) 25 mA 50 mA 75 mA VDS = 26 Vdc f1 = 960.0 MHz, f2 = 960.1 MHz 10 15 20 25 30 35 40 −31 −60 100 mA −65 5 19.9 VDS, DRAIN SOURCE SUPPLY (VOLTS) −32 Pout, OUTPUT POWER (dBm) PEP Figure 6. Power Gain and Intermodulation Distortion versus Supply Voltage 0 −10 Pout , OUTPUT POWER (dBm) −20 3rd Order −30 −40 5th Order −50 7th Order −60 −70 10 15 20 25 30 35 40 Pout, OUTPUT POWER (dBm) VDS = 26 Vdc f1 = 960.0 MHz, f2 = 960.1 MHz 41 39 37 35 33 31 29 27 25 925 Figure 7. Intermodulation Distortion versus Output Power IMD, INTERMODULATION DISTORTION (dBc) Pin = 20 dBm 15 dBm VDS = 26 Vdc IDQ = 25 mA Single−Tone 10 dBm 935 945 955 965 975 985 f, FREQUENCY (MHz) Figure 8. Intermodulation Distortion Products versus Output Power Figure 9. Output Power versus Frequency MRF9002NR2 RF Device Data Freescale Semiconductor 5 TYPICAL CHARACTERISTICS 12 11 10 9 C, CAPACITANCE (pF) 8 7 6 5 4 3 2 22 23 24 25 26 27 28 29 30 VDS, DRAIN SOURCE SUPPLY (VOLTS) Crss Coss Ciss MTTF FACTOR (HOURS X AMPS2) 109 108 107 106 90 100 110 120 130 140 150 160 170 180 190 200 210 TJ, JUNCTION TEMPERATURE (°C) This above graph displays calculated MTTF in hours x ampere2 drain current. Life tests at elevated temperatures have correlated to better than ±10% of the theoretical prediction for metal failure. Divide MTTF factor by ID2 for MTTF in a particular application. Figure 10. Capacitance versus Drain Source Voltage Figure 11. MTTF Factor versus Junction Temperature MRF9002NR2 6 RF Device Data Freescale Semiconductor TRANSISTORS 1 and 2 TRANSISTOR 3 Zo = 50 Ω T3 985 MHz Zsource f = 925 MHz Zo = 50 Ω T1 985 MHz Zsource f = 925 MHz T2 985 MHz Zsource T2 f = 925 MHz Zload 985 MHz f = 925 MHz T1 985 MHz Zload f = 925 MHz 985 MHz T3 Zload f = 925 MHz VDD = 26 V, IDQ = 25 mA, Pout = 2 W PEP f MHz 925 960 985 Zsource Ω 4.5 + j13.3 4.3 + j15.3 4.1 + j15.8 Transistor 1 VDD = 26 V, IDQ = 25 mA, Pout = 2 W PEP f MHz 925 960 985 Zsource Ω 6.0 + j12.3 5.9 + j14.3 5.8 + j16.5 Transistor 2 VDD = 26 V, IDQ = 25 mA, Pout = 2 W PEP f MHz 925 960 985 Zsource Ω 4.3 + j12.2 4.3 + j14.0 3.9 + j15.9 Transistor 3 Zload Ω 23.1 + j6.5 22.8 + j8.4 22.6 + j9.3 Zload Ω 19.7 + j27.8 22.0 + j23.9 22.5 + j25.4 Input Matching Network Device Under Test Output Matching Network Zload Ω 23.4 + j9.2 23.2 + j10.4 23.0 + j11.1 Zsource = Test circuit impedance as measured from gate to ground. Zload = Test circuit impedance as measured from drain to ground. Z source Z load Figure 12. Series Equivalent Source and Load Impedance MRF9002NR2 RF Device Data Freescale Semiconductor 7 NOTES MRF9002NR2 8 RF Device Data Freescale Semiconductor NOTES MRF9002NR2 RF Device Data Freescale Semiconductor 9 NOTES MRF9002NR2 10 RF Device Data Freescale Semiconductor PACKAGE DIMENSIONS h X 45 _ A E2 1 16 NOTES: 1. CONTROLLING DIMENSION: MILLIMETER. 2. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DATUM PLANE −H− IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.250 PER SIDE. DIMENSIONS D AND E1 DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE −H−. 5. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION IS 0.127 TOTAL IN EXCESS OF THE b DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. DATUMS −A− AND −B− TO BE DETERMINED AT DATUM PLANE −H−. MILLIMETERS MIN MAX 2.000 2.300 0.025 0.100 1.950 2.100 6.950 7.100 4.372 5.180 8.850 9.150 6.950 7.100 4.372 5.180 0.466 0.720 0.250 BSC 0.300 0.432 0.300 0.375 0.180 0.279 0.180 0.230 0.800 BSC −−− 0.600 0_ 7_ 0.200 0.200 0.100 14 x e D e/2 D1 8 9 E1 8X B BOTTOM VIEW E CB S bbb Y A A2 M b1 c C DATUM PLANE SEATING PLANE H SECT W - W L1 ccc C q W W L 1.000 0.039 DETAIL Y A1 GAUGE PLANE CASE 978 - 03 ISSUE C PLASTIC PFP - 16 RF Device Data Freescale Semiconductor ÇÇÇ ÉÉ ÇÇÇ ÉÉ b aaa M c1 CA S DIM A A1 A2 D D1 E E1 E2 L L1 b b1 c c1 e h q aaa bbb ccc MRF9002NR2 11 How to Reach Us: Home Page: www.freescale.com E - mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1 - 800 - 521 - 6274 or +1 - 480 - 768 - 2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1 - 8 - 1, Shimo - Meguro, Meguro - ku, Tokyo 153 - 0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1 - 800 - 441 - 2447 or 303 - 675 - 2140 Fax: 303 - 675 - 2150 LDCForFreescaleSemiconductor@hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”, must be validated for each customer application by customer’s technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescalet and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2006. All rights reserved. RoHS - compliant and/or Pb - free versions of Freescale products have the functionality and electrical characteristics of their non - RoHS - compliant and/or non - Pb - free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale’s Environmental Products program, go to http://www.freescale.com/epp. MRF9002NR2 1Rev. 8, 5/2006 2 Document Number: MRF9002NR2 RF Device Data Freescale Semiconductor