HF165F/12-HT(257)

H F1 6 5F SOLAR RELAY Features File No:E134517 ● 35A swithing capitable. ● Applicable to inverter used for photovoltaic power generation systems. ● Ideal for UPS. ● 1.8mm contact gap(compliant to European Photovoltaic Standard VDE0126). ● Product in accordance to IEC 60335 available. ● Low coil hoilding voltage contributes to saving energy of equipment. ● UL insulation system: class F. RoHS compliant V D E File No:40037289 File No:R 50463438 File No:CQC18002189685 CQC18002202621 CONTACT DATA COIL 1A Contact arrangement Typ.: 15mV(at 10A) Max.: 100mV(at 10A) Voltage drop AgSnO2 Contact material Resistive: 35A 250VAC Contact rating (Res. load) Inductive: 35A 277VAC (cosø=0.8) 1s:9s Max. switching voltage Max. switching current 35A Max. switching power 9695VA 1 x 106 OPS Mechanical endurance 3 x 104 OPS (35A 250VAC, Insulation resistance 1000M (at 500VDC) Dielectric Between coil & contacts strength Between open contacts 4000VAC 1min 2500VAC 1min Surge voltage (between coil & contacts) COIL DATA Nominal Voltage VDC 1) at 23 Pick-up Drop-out Voltage Voltage VDC VDC max1) min1) Max. Voltage VDC * 2) Coil Resistance 5 3.75 0.35 5.5 12 9 0.84 13.2 64 x (1 10%) 24 18 1.68 26.4 256 x (1 10%) 48 36 3.36 52.8 1024 x (1 10%) 11.1 x (1 10%) Notes: 1)The data shown above are initial values. 2)*Maximun voltage refers to the maximun voltage which relay coil could endure in a short period of time. 6kV (1.2/50µs) Operate time (at rated. volt.) 15ms max. Release time (at rated. volt.) 10ms max. 70K max.(Contact load current 43A, 50% of rated o voltage excitation, at 85 C) Functional Shock resistance Destructive UL/CUL VDE 980m/s2 TUV -40 C to 85 C o (Apply holding voltage to coil) 5% to 85% RH Humidity SAFETY APPROVAL RATINGS 98m/s2 10Hz to 55Hz 1.5mm DA o Ambient temperature Notes: 1)The coil holding voltage is the voltage applied to coil 100ms after the rated voltage. 2)To avoid overheating and burning, the coil can not be consistently applied to with voltage larger than maximum holding voltage. o CHARACTERISTICS Vibration resistance Holding voltage Resistive load, at 85 C, 1s on 9s off) Notes: 1)The relay connections and wiring have to be designed with an adequate cross setions to ensure the current flow and heat dissipation. Temperature rise (at rated. volt.) 40% to 110%UN(at 23 ) 50% to 70%UN(at 85 ) 277VAC 1) Electrical endurance Approx.2.25W Coil power 35A 277VAC/250VAC general use 3 x 104OPS 85 C o 35A 250VAC 3 x 104OPS 85 C 43A 277VAC/250VAC 85 C Making 10A Carrying 43A Breaking10A 85 C 40A 277VAC/250VAC 60 C o o CQC o o Notes: 1) All values unspecified are at room temperature. 2) Only typical loads are listed above. Other load specifications can be available upon request. PCB Termination Approx.36g Unit weight Construction Flux proofed Notes: The data shown above are initial values. HONGFA RELAY ISO9001、ISO/TS16949、ISO14001、OHSAS18001、IECQ QC 080000 CERTIFIED 304 2020 Rev. 1.01 ORDERING INFORMATION H F 1 6 5F / 12 -H T (XXX) Type Coil voltage 5, 12, 24, 48VDC Contact arrangement H:1 Form A Contact matcrial T: AgSnO2 Special code3) XXX: Customer special requirement Nil: Standard Notes: 1) Water cleaning or surface process is not suggested after the flux-proofed relays are assembled on PCB. 2) Flux-proofed relays can not be used in the environment with pollutants like H2S, SO2, NO2, dust, etc. 3) The customer special requirement express as special code after evaluating by Hongfa. e.g.(335) stands for product in accordance to IEC 60335-1 (GWT). OUTLINE DIMENSIONS, WIRING DIAGRAM AND PC BOARD LAYOUT Unit: mm Outline Dimensions 5.5 ±0.4 19.4 ±0.4 3.35 ±0.3 27.4 ±0.4 0.95 ±0.2 3.8 ±0.3 0.7X0.7 ±0.2 PCB Layout (Bottom view) 3.92 20.1 ±0.4 22.4 ±0.4 Wiring Diagram + 0.08 -0.03 1.78 ≤R0.5 ≤R0.5 2XØ1.1 + 00. 1 3.81 13.97 18.75 Notes: 1) In case of no tolerance shown in outline dimension: outline dimension ≤1mm, tolerance should be ±0.2mm; outline dimension ＞1mm and ≤5mm, tolerance should be ±0.3mm; outline dimension ＞5mm, tolerance should be ±0.4mm. 2) The tolerance without indicating for PCB layout is always ±0.1mm. 305 CHARACTERISTIC CURVES MAXIMUM SWITCHING POWER ENDURANCE CURVE 100 100 50 AC Resistive load 250VAC Resistive load 10 10 5 1 1 0.5 10 100 1000 0 5 15 Contact Voltage(V) 25 35 Contact Current(A) Test conditions: Resistive load, 250VAC, o Flux proofed, at 85 C, 1s on 9s off Disclaimer The specification is for reference only. See to "Terminology and Guidelines" for more information. Specifications subject to change without notice. We could not evaluate all the performance and all the parameters for every possible application. Thus the user should be in a right position to choose the suitable product for their own application. If there is any query, please contact Hongfa for the technical service. However, it is the user’s responsibility to determine which product should be used only. © Xiamen Hongfa Electroacoustic Co., Ltd. All rights of Hongfa are reserved. 306