1N6392

TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com HIGH RELIABILITY SCHOTTKY RECTIFIER Qualified per MIL-PRF-19500/554 DEVICES LEVELS 1N6392 JAN JANTX JANTXV ABSOLUTE MAXIMUM RATINGS (TC = +25°C unless otherwise noted) (Per Diode) Parameters / Test Conditions Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Forward Current, 115°C Peak Surge Forward Current @ tp = 8.3ms, half sinewave, Io = 0; VRM = 0 Thermal Resistance, Junction to Case Operating Junction Temperature Storage Temperature Symbol VRWM VRRM VR IFM IFSM Rθjc Tj Tstg Value 45 45 45 60 Note 1 1000 1.0 -55°C to 175 -55°C to 175 Unit V V V Apk Apk °C/W °C °C DO-5 ELECTRICAL CHARACTERISTICS (TA = +25°C, unless otherwise noted) (Per Diode) Parameters / Test Conditions Forward Voltage IF = 10A, Tj = 25°C* IF = 60A, Tj = 25°C* IF = 120A, Tj = 25°C* IF = 10A, Tj = -55°C* Reverse Current VR = 45V, Tj = 25°C VR = 45V, Tj = 125°C VR = 45V, Tj = 175°C Junction Capacitance VR = 5V f = 1MHz * Pulse test: Pulse width 300 µsec, Duty cycle 2% Note: 1. Derate linearly @ 1.09A/°C from Tj = Tc >115°C Symbol Min. Max. Unit VFM 0.51 0.68 0.82 0.69 2.0 60 200 3000 V IRM mA Cj pF T4-LDS-0053 Rev. 2 (091676) Page 1 of 3 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com HIGH RELIABILITY SCHOTTKY RECTIFIER Qualified per MIL-PRF-19500/554 GRAPHS FIGURE 1 TYPICAL FORWARD CHARACTERISTICS FIGURE 3 TYPICAL JUNCTION CAPACITANCE FIGURE 4 FORWARD CURRENT DERATING FIGURE 2 TYPICAL REVERSE CHARACTERISTICS T4-LDS-0053 Rev. 2 (091676) Page 2 of 3 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com HIGH RELIABILITY SCHOTTKY RECTIFIER Qualified per MIL-PRF-19500/554 PACKAGE DIMENSIONS DO-5 NOTES: 1. 2. 3. 4. 5. 6. 7. Dimensions are in inches. Millimeters are given for general information only. Units must not be damaged by torque of 30 inch-pound applied to .25-28 UNF-2B nut assembled on thread. Length of incomplete or undercut threads of UD. Maximum pitch diameter of plated threads shall be basic pitch diameter .2268 inch (5.76 mm) reference (FED-STD-H28, “Screw-Thread Standards for Federal Services”). A chamfer or undercut on one or both ends of the hex portion is optional; minimum base diameter at seating plane .600 inch (15.24 mm). The angular orientation and peripheral configuration of terminal 1 is undefined, however, the major surfaces over dimensions C and C1 shall be flat and the minimum cross-sectional area from the hole to any point on the periphery shall be .0025 in2 (1.59 mm2). In accordance with ASME Y14.5M, diameters are equivalent to φx symbology. Ltr C C1 CD CH HF HT1 HT2 OAH SD SL SU UD φT .422 .220 .140 .453 .090 .249 .175 10.72 5.59 3.56 11.50 2.28 6.32 4.44 4 .669 .115 .060 .750 1.00 Dimensions Inches Millimeters Max Min Max Min .375 9.52 .025 .080 .667 .450 .688 .200 17.00 2.93 1.53 19.05 25.40 5 0.64 2.03 16.94 11.43 17.47 5.08 6 Notes 7 8. T4-LDS-0053 Rev. 2 (091676) Page 3 of 3