CM100DU-34KA

MITSUBISHI IGBT MODULES CM100DU-34KA HIGH POWER SWITCHING USE CM100DU-34KA G IC ................................................................... 100A G VCES .......................................................... 1700V G Insulated Type G 2-elements in a pack APPLICATION General purpose inverters & Servo controls, etc OUTLINE DRAWING & CIRCUIT DIAGRAM Dimensions in mm 108 93 ±0.25 14 14 Tc measured point 14 E2 G2 6 (8.25) C2E1 E2 C1 ±0.25 G1 E1 6 48 CM (18) CIRCUIT DIAGRAM C2E1 E2 C1 25 3-M6 NUTS 4-φ6. 5 MOUNTING HOLES 25 21.5 2.5 4 18 7 18 7 18 2.8 0.5 15.85 0.5 0.5 0.5 7.5 29 +1.0 –0.5 22 LABEL 8.5 4 Sep. 2001 G1 E1 15 62 E2 G2 MITSUBISHI IGBT MODULES CM100DU-34KA HIGH POWER SWITCHING USE MAXIMUM RATINGS (Tj = 25°C) Symbol VCES VGES IC ICM IE (Note 1) IEM (Note 1) PC (Note 3) Tj Tstg Viso — — Parameter Collector-emitter voltage Gate-emitter voltage Collector current Emitter current Maximum collector dissipation Junction temperature Storage temperature Isolation voltage Torque strength Weight G-E Short C-E Short TC = 25°C Pulse TC = 25°C Pulse TC = 25°C Conditions Ratings 1700 ±20 100 200 100 200 890 –40 ~ +150 –40 ~ +125 3500 3.5 ~ 4.5 3.5 ~ 4.5 400 Unit V V A A W °C °C V N•m N•m g (Note 2) (Note 2) Main terminal to base plate, AC 1 min. Main Terminal M6 Mounting holes M6 Typical value ELECTRICAL CHARACTERISTICS (Tj = 25°C) Symbol ICES VGE(th) IGES VCE(sat) Cies Coes Cres QG td(on) tr td(off) tf trr (Note 1) Qrr (Note 1) Parameter Collector cutoff current Gate-emitter threshold voltage Gate leakage current Collector-emitter saturation voltage Input capacitance Output capacitance Reverse transfer capacitance Total gate charge Turn-on delay time Turn-on rise time Turn-off delay time Turn-off fall time Reverse recovery time Reverse recovery charge Test conditions VCE = VCES, VGE = 0V IC = 10mA, VCE = 10V VGE = VGES, VCE = 0V Tj = 25°C IC = 100A, VGE = 15V Tj = 125°C VCE = 10V VGE = 0V VCC = 1000V, IC = 100A, VGE = 15V VCC = 1000V, IC = 100A VGE1 = VGE2 = 15V RG = 3.1Ω, Inductive load switching operation IE = 100A IE = 100A, VGE = 0V, Tj = 25°C IE = 100A, VGE = 0V, Tj = 125°C IGBT part (1/2 module) FWDi part (1/2 module) Case to fin, Thermal compound applied*2 (1/2 module) Tc measured point is just under the chips Min. — 4 — — — — — — — — — — — — — — — — — — — Limits Typ. — 5.5 — 3.2 3.8 — — — 450 — — — — — 5.8 — 2.2 — — 0.04 — Max. 1 7 0.5 4.0 — 14 2.4 0.75 — 350 150 550 800 600 — 4.6 — 0.14 0.24 — 0.09*3 Unit mA V µA V nF nC ns ns µC V V °C/W VEC(Note 1) Emitter-collector voltage Rth(j-c)Q Rth(j-c)R Rth(c-f) Rth(j-c’)Q Thermal resistance*1 Contact thermal resistance Thermal resistance Note 1. IE, VEC, trr, Qrr, die/dt represent characteristics of the anti-parallel, emitter to collector free-wheel diode. (FWDi). 2. Pulse width and repetition rate should be such that the device junction temp. (Tj) does not exceed Tjmax rating. 3. Junction temperature (Tj) should not increase beyond 150°C. 4. Pulse width and repetition rate should be such as to cause negligible temperature rise. *1 : Tc measured point is indicated in OUTLINE DRAWING. *2 : Typical value is measured by using Shin-etsu Silicone “G-746”. *3 : If you use this value, Rth(f-a) should be measured just under the chips. Sep. 2001 MITSUBISHI IGBT MODULES CM100DU-34KA HIGH POWER SWITCHING USE PERFORMANCE CURVES OUTPUT CHARACTERISTICS (TYPICAL) 200 COLLECTOR CURRENT IC (A) TRANSFER CHARACTERISTICS (TYPICAL) 11 COLLECTOR CURRENT (A) Tj = 25°C VGE = 20V 15 14 12 200 VCE = 10V Tj = 25°C 160 Tj = 125°C 120 160 10 120 80 9 80 40 8 40 0 0 2 4 6 8 10 0 0 4 8 12 16 20 COLLECTOR-EMITTER VOLTAGE VCE (V) GATE-EMITTER VOLTAGE VGE (V) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) 6 VGE = 15V Tj = 25°C 5 Tj = 125°C 4 3 2 1 0 10 Tj = 25°C 8 6 IC = 200A 4 IC = 100A IC = 40A 2 0 40 80 120 160 200 0 6 8 10 12 14 16 18 20 COLLECTOR CURRENT IC (A) GATE-EMITTER VOLTAGE VGE (V) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) 103 EMITTER CURRENT IE (A) 7 5 3 2 CAPACITANCE–VCE CHARACTERISTICS (TYPICAL) 102 CAPACITANCE Cies, Coes, Cres (nF) 7 5 3 2 Tj = 25°C 102 7 5 3 2 101 7 5 3 2 Cies 101 7 5 3 2 100 7 5 3 2 Coes Cres 100 1 2 3 4 5 VGE = 0V 10–1 –1 10 2 3 5 7 100 2 3 5 7 101 2 3 5 7 102 COLLECTOR-EMITTER VOLTAGE VCE (V) EMITTER-COLLECTOR VOLTAGE VEC (V) Sep. 2001 MITSUBISHI IGBT MODULES CM100DU-34KA HIGH POWER SWITCHING USE HALF-BRIDGE SWITCHING CHARACTERISTICS (TYPICAL) 104 7 5 3 2 REVERSE RECOVERY TIME trr (ns) REVERSE RECOVERY CURRENT lrr (A) REVERSE RECOVERY CHARACTERISTICS OF FREE-WHEEL DIODE (TYPICAL) 103 7 5 3 2 SWITCHING TIMES (ns) tf td(off) td(on) Conditions: VCC = 1000V VGE = ±15V RG = 3.1Ω Tj = 125°C Inductive load 2 3 5 7 102 2 3 5 7 103 103 7 5 3 2 102 7 5 3 2 trr Irr Conditions: VCC = 1000V VGE = ±15V RG = 3.1Ω Tj = 25°C Inductive load 2 3 5 7 102 2 3 5 7 103 102 7 5 3 2 tr 101 1 10 101 1 10 COLLECTOR CURRENT IC (A) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT part & FWDi part) EMITTER CURRENT IE (A) NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j–c) (°C/W) GATE-EMITTER VOLTAGE VGE (V) 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7 100 2 3 5 7 101 101 7 IGBT part: 5 Per unit base = Rth(j– c) = 0.14°C/ W 3 FWDi part: 2 Per unit base = Rth(j– c) = 0.24°C/ W 100 7 5 3 2 7 5 3 2 7 5 3 2 3 2 GATE CHARGE CHARACTERISTICS (TYPICAL) 20 IC = 100A 16 VCC = 800V 12 VCC = 1000V 8 10–1 10–1 7 5 3 2 7 5 3 2 10–2 10–2 Single Pulse TC = 25°C 4 10–3 10–3 10–5 2 3 5 710–4 2 3 5 7 10–3 TMIE (s) 0 0 100 200 300 400 500 600 GATE CHARGE QG (nC) Sep. 2001