Is Now Part of
To learn more about ON Semiconductor, please visit our website at
www.onsemi.com
Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers
will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor
product management systems do not have the ability to manage part nomenclature that utilizes an underscore
(_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain
device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated
device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please
email any questions regarding the system integration to Fairchild_questions@onsemi.com.
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
FODM3062, FODM3063, FODM3082, FODM3083
4-Pin Full Pitch Mini-Flat Package Zero-Cross
Triac Driver Output Optocouplers
Features
Description
• Critical Rate of Rise of Off-Stage Voltage
- dv/dt of 600 V/µs Guaranteed
• Zero Voltage Crossing
• Peak Blocking Voltage
- 600 V (FODM306X)
- 800 V (FODM308X)
• Compact 4-Pin Surface Mount Package
- 2.4 mm Maximum Standoff Height
• Safety Regulatory Approvals:
- UL1577, 3,750 VACRMS for 1 Minute
- DIN-EN/IEC60747-5-5, 565 V Peak Working
Insulation Voltage
The FODM306X and FODM308X series consist of an
infrared emitting diode optically coupled to a monolithic
silicon detector performing the function of a zero voltage
crossing bilateral triac driver, and is housed in a compact
4-pin mini-flat package. The lead pitch is 2.54 mm. They
are designed for use with a triac in the interface of logic
systems to equipment powered from 115/240 VAC lines,
such as solid state relays, industrial controls, motors,
solenoids and consumer appliances.
Applications
•
•
•
•
•
•
•
•
Solenoid/valve controls
Lighting controls
Static power switches
AC motor drives
Temperature controls
E.M. contactors
AC motor starters
Solid state relays
Functional Schematic
ANODE 1
CATHODE 2
Package Outlines
4 MAIN TERM.
ZERO
CROSSING
CIRCUIT
3 MAIN TERM.
)LJXUH)XQFWLRQDO6FKHPDWLF
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
)LJXUH3DFNDJH2XWOLQH
www.fairchildsemi.com
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
May 2016
As per DIN EN/IEC 60747-5-5, this optocoupler is suitable for “safe electrical insulation” only within the safety limit
data. Compliance with the safety ratings shall be ensured by means of protective circuits.
Parameter
Installation Classifications per DIN VDE
0110/1.89 Table 1, For Rated Mains Voltage
Characteristics
< 150 VRMS
I–IV
< 300 VRMS
I–III
Climatic Classification
40/100/21
Pollution Degree (DIN VDE 0110/1.89)
2
Comparative Tracking Index
Symbol
175
Value
Unit
Input-to-Output Test Voltage, Method A, VIORM x 1.6 = VPR,
Type and Sample Test with tm = 10 s, Partial Discharge < 5 pC
904
Vpeak
Input-to-Output Test Voltage, Method B, VIORM x 1.875 = VPR,
100% Production Test with tm = 1 s, Partial Discharge < 5 pC
1060
Vpeak
VIORM
Maximum Working Insulation Voltage
565
Vpeak
VIOTM
Highest Allowable Over-Voltage
6000
Vpeak
5
mm
VPR
Parameter
External Creepage
5
mm
0.4
mm
Case
Temperature(1)
150
°C
Input
Current(1)
200
mA
300
mW
> 109
External Clearance
DTI
TS
IS,INPUT
Distance Through Insulation (Insulation Thickness)
PS,OUTPUT Output
RIO
Power(1)
Insulation Resistance at TS, VIO = 500 V(1)
Note:
1. Safety limit values – maximum values allowed in the event of a failure.
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
www.fairchildsemi.com
2
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Safety and Insulation Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The
absolute maximum ratings are stress ratings only. TA = 25°C unless otherwise specified.
Symbol
Parameter
Value
Unit
TSTG
Storage Temperature
-55 to +150
°C
TOPR
Operating Temperature
-40 to +100
°C
Junction Temperature
-40 to +125
°C
260 for 10 sec
°C
TJ
TSOL
Lead Solder Temperature
EMITTER
IF (avg)
Continuous Forward Current
60
mA
IF (pk)
Peak Forward Current (1 μs pulse, 300 pps.)
1
A
Reverse Input Voltage
6
V
Power Dissipation (No derating required over operating temp. range)
100
mW
IT(RMS)
On-State RMS Current
70
mA
VDRM
Off-State Output Terminal Voltage
600
V
VR
PD(EMITTER)
DETECTOR
PD(DETECTOR)
FODM3062/FODM3063
FODM3082/FODM3083
800
V
Power Dissipation (No derating required over operating temp. range)
300
mW
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
www.fairchildsemi.com
3
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Absolute Maximum Ratings
TA = 25°C unless otherwise specified.
Individual Component Characteristics
Symbol Parameter
Test Conditions
Device
Min.
Typ.
Max.
Unit
EMITTER
VF
Input Forward Voltage
IF = 30 mA
All
1.50
V
IR
Reverse Leakage Current
VR = 6 V
All
100
μA
500
nA
DETECTOR
IDRM
Peak Blocking Current Either
Rated VDRM, IF = 0(2)
Direction
All
dv/dt
Critical Rate of Rise of
Off-State Voltage
IF = 0 (Figure 10)(3)
All
600
Test Conditions
Device
Min.
V/μs
Transfer Characteristics
Symbol Parameter
Typ.
FODM3062,
IFT
LED Trigger Current
Main Terminal
FODM3082
Voltage = 3 V(4)
FODM3063,
VTM
Holding Current, Either Direction
Peak On-State Voltage,
Either Direction
mA
5
All
IF = Rated IFT,
ITM = 100 mA peak
All
Test Conditions
Device
Unit
10
FODM3083
IH
Max.
300
µA
3
V
Max.
Unit
All
20
V
All
2
mA
Max.
Unit
Zero Crossing Characteristics
Symbol Parameter
Inhibit Voltage,
VIH
MT1-MT2 Voltage
Min.
Typ.
IFT = Rated IFT
above which device
will not trigger
IDRM2
Leakage in Inhibit State
IFT = Rated IFT,
Rated VDRM,
Off-State
Isolation Characteristics
Symbol Parameter
VISO
Steady State Isolation
Voltage(5)
Test Conditions
Device
Min.
1 Minute,
R.H. = 40% to 60%
All
3,750
Typ.
VACRMS
Notes:
2. Test voltage must be applied within dv/dt rating.
3. This is static dv/dt. See Figure 10 for test circuit. Commutating dv/dt is function of the load-driving thyristor(s) only.
4. All devices are guaranteed to trigger at an IF value less than or equal to max IFT. Therefore, recommended
operating IF lies between max IFT (10mA for FODM3062/82, 5mA for FODM3063/83) and absolute max IF (60 mA).
5. Steady state isolation voltage, VISO, is an internal device dielectric breakdown rating. For this test, pins 1 & 2 are
common, and pins 3 & 4 are common.
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
www.fairchildsemi.com
4
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Electrical Characteristics
1000
1.8
VDRM = 600V
1.7
IDRM - LEAKAGE CURRENT (nA)
VF - FORWARD VOLTAGE (V)
1.6
1.5
1.4
TA = -40°C
1.3
1.2
TA = 25°C
1.1
100
10
1
TA = 100°C
1.0
0.1
-40
0.9
10
1
100
-20
0
20
40
60
80
IF - FORWARD CURRENT (mA)
TA - AMBIENT TEMPERATURE (°C)
Fig. LED Forward Voltage vs. Forward Current
Fig. Leakage Current vs. Ambient Temperature
100
1.6
VTM = 3V
NORMALIZED TO TA = 25°C
NORMALIZED TO TA = 25°C
I FT - TRIGGER CURRENT (NORMALIZED)
I H - HOLDING CURRENT (NORMALIZED)
10
1.0
0.1
-40
-20
0
20
40
60
80
1.2
1.0
0.8
0.6
0.8
-40
100
TA - AMBIENT TEMPERATURE (°C)
-20
0
20
40
60
80
100
TA - AMBIENT TEMPERATURE (°C)
Fig. Holding Current vs. Ambient Temperature
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
1.4
Fig. Trigger Current vs. Ambient Temperature
www.fairchildsemi.com
5
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Typical Performance Characteristics
12
IFT - LED TRIGGER CURRENT (NORMALIZED)
NORMALIZED TOPWIN >> 100μs
10
8
6
4
2
NORMALIZED TO TA = 25°C
1.3
1.2
(NORMALIZED)
V DRM- OFF-STATE OUTPUT TERMINAL VOLTAGE
1.4
TA = 25°C
1.1
1.0
0.9
0.8
0.7
0.6
-40
0
1
10
0
-20
100
20
40
60
80
100
T A - AMBIENT TEMPERATURE (°C)
PWIN - LED TRIGGER PULSE WIDTH (°C)
Fig. LED Current Required to Trigger vs. LED Pulse Width
Fig. Off-State Output Terminal Voltage vs. Ambient Temperature
800
TA = 25°C
ITM - ON-STATE CURRENT (mA)
600
400
200
0
-200
-400
-600
-800
-4
-3
-2
-1
0
1
2
3
4
VTM - ON-STATE VOLTAGE (V)
Fig. On-State Characteristics
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
www.fairchildsemi.com
6
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Typical Performance Characteristics (Continued)
RTEST
800V (FODM3082)Vdc
(FODM3083)
600V (FODM3062)
(FODM3063)
1. The mercury wetted relay provides a high speed repeated
pulse to the D.U.T.
2. 100x scope probes are used, to allow high speeds and
voltages.
3. The worst-case condition for static dv/dt is established by
triggering the D.U.T. with a normal LED input current, then
removing the current. The variable RTEST allows the dv/dt
to be gradually increased until the D.U.T. continues to trigger
in response to the applied voltage pulse, even after the LED
current has been removed. The dv/dt is then decreased until
the D.U.T. stops triggering. tRC is measured at this point
and recorded.
R = 10 kΩ
CTEST
PULSE
INPUT
MERCURY
WETTED
RELAY
X100
SCOPE
PROBE
D.U
D.
U.T.
Vmax = 800V (FODM3082, FODM3083)
=600V (FODM3062, FODM3063)
APPLIED VOLTAGE
WAVEFORM
78V (FODM3062, FODM3063)
504V (FODM3082, FODM3083)
dv/dt =
0 VOLTS
τRC
0.63 Vmax
τRC
378
= τ
(FODM3062, FODM3063)
RC
504
(FODM3082, FODM3083)
= τ
RC
Note:
This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.
Figure . Static dv/dt Test Circuit
240 VAC
R1
1
VCC
Rin
2
D1
Suggested method of firing two, back-to-back
SCR’s, with a Fairchild triac driver. Diodes can
be 1N4001; resistors, R1 and R2, are optional
330 ohms.
4
FODM3062
FODM3063
FODM3082
FODM3083
SCR
3
SCR
360 Ω
R2
D2
LOAD
Note:
This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.
Figure . Inverse-Parallel SCR Driver Circuit (240 VAC)
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
www.fairchildsemi.com
7
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Typical Application Information
The power dissipated from resistors placed in series
with the opto-TRIAC and the gate of the power TRIAC
is much smaller than one would expect. These current
handling components only conduct current when the
mains voltage is less than the maximum inhibit
voltage. If the opto-TRIAC is triggered when the mains
voltage is greater than the inhibit voltage, only the
TRIAC leakage current will flow. The power dissipation
in a 360 Ω resistor shown in Figure 1 is the product
of the resistance (360 Ω) times the square of the
current sum of main TRIAC’s gate current plus the
current flowing gate to the MT2 resistor connection
(330 Ω). This power calculation is further modified by
the duty factor of the duration for this current flow.
The duty factor is the ratio of the turn-on time of the
main TRIAC to the sine of the single cycle time.
Assuming a main TRIAC turn-on time of 50 μs
and a 60 Hz mains voltage, the duty cycle is
approximately 0.6%.The opto-TRIAC only conducts
current while triggering the main TRIAC. Once the
main TRIAC fires, its on-state voltage is typically
lower than the on-state sustaining voltage of the
opto-TRIAC. Thus, once the main TRIAC fires, the
opto-TRIAC is often shunted off.This situation results
in very low power dissipation forboth the 360Ω and
330 Ω resistors, when driving a traditional four
quadrant power TRIAC.
The following will present the calculations for
determining the power dissipation of the current
limiting resistors found in an opto-TRIAC driver
interface.
Figure 1 shows a typical circuit to drive a sensitive
gate four quadrant power TRIAC. This figure provides
typical resistor values for a zero line cross detecting
opto-TRIAC when operated from a mains voltage of
20 V to 240 V. The wattage rating for each resistor
is not given because their dissipation is dependent
uponcharacteristics of the power TRIAC being driven.
Recall that the opto-TRIAC is used to trigger a four
quadrant power TRIAC. Please note that these optoTRIACs
are
not
recommended
for
driving
“snubberless” three quadrant power TRIACs.
Under normal operation, the opto-TRIAC will fire when
the mains voltage is lower than the minimum inhibit
trigger voltage, and the LED is driven at a current
greater than the maximum LED trigger current. As an
example for the FODM3063, the LED trigger current
should be greater than 5mA, and the mains voltage is
less than 10 V peak. The inhibit voltage has a typical
range of 10 V minimum and 20 V maximum. This
means that if a sufficient LED current is flowing when
the mains voltage is less than 10V, the device will fire.
If a trigger appears between 10V and 20V, the device
may fire. If the trigger occurs after the mains voltage
has reached 20Vpeak, the device will not fire.
Rin
1
If a three quadrant “snubberless” TRIAC is driven by
the opto-TRIAC, the calculations are different. When
the main power TRIAC is driving a high power factor
(resistive) load, it shuts off during the fourth quadrant.
360 Ω
4
HOT
VCC
2
FODM3062
FODM3063
FODM3082
FODM3083
39
3
240 VAC
30 Ω
0.01ȝ)
LOAD
*
Typical circuit for use when hot line switching of 240VAC
is required. In this circuit the “hot” side of the line is
switched and the load connected to the cold or neutral
side. The load may be connected to either the neutral or
hot line.
Rin is calculated so that IF is equal to the rated IFT of the
part, 5mA for the FODM3063/83 and 10mA for the
FODM3062/82. The 39Ω resistor and 0.01μF capacitor
are for snubbing of the triac and may or may not be
necessary depending upon the particular triac and load
used.
NEUTRAL
For highly inductive loads (power factor < 0.5), change this value to 360 ohms.
Figure 1. Hot-Line Switching Application Circuit
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
www.fairchildsemi.com
8
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Determining the Power Rating of the Series Resistors Used in a Zero-Cross OptoTRIAC Driver Application
The real power in the snubber resistor is based upon
the integral of the power transient present when the
load commutes. A fast commuting transient may allow
a peak current of 4A to 8A in the snubbing filter.For
best results, the capacitor should be a non-polarized
AC unit with a low ESR. The 39Ω seriesresistor sets
a time constant and limits the peak current. For a
resistive load with a power factor near unity, the
commutating transients will be small. This results in a
very small peak current given the 0.01 μF capacitor’s
reactance. Normally, for factional horse-power reactive
loads, the resistor found in the snubber circuit will
have a power rating from 1/2 W to 2 W. The resistor
should be a low inductance type to adequately filter
the high frequency transients.
Power in the 360Ω resistor, when driving a sensitive
gate 4 quadrant power TRIAC:
IGT = 20mA
VGT = 1.5V
DF = 0.6%
P = (IGT +VGT / 330Ω)2 x 360Ω x DF
P = (20mA + 1.5 / 330Ω)2 *x 360Ω x 0.6% = 1.3mW
A 1/4 watt resistor is more than adequate for both the
360Ω and 330Ω resistors.
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
www.fairchildsemi.com
9
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
If sufficient holding current is still flowing through the
opto-TRIAC, the opto-TRIAC will turn-on and attempt
to carry the power TRIACs load. This situation typically
causes the opto-TRIAC to operate beyond its
maximum current rating, and product and resistor
failures typically result. For this reason, using an optoTRIAC to drive a three quadrant “snubberless” power
TRIAC is not recommended.
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Reflow Profile
Temperature (°C)
TP
260
240
TL
220
200
180
160
140
120
100
80
60
40
20
0
Max. Ramp-up Rate = 3°C/S
Max. Ramp-down Rate = 6°C/S
tP
Tsmax
tL
Preheat Area
Tsmin
ts
240
120
360
Time 25°C to Peak
Time (seconds)
Profile Freature
Pb-Free Assembly Profile
Temperature Min. (Tsmin)
150°C
Temperature Max. (Tsmax)
200°C
Time (tS) from (Tsmin to Tsmax)
60–120 seconds
Ramp-up Rate (tL to tP)
3°C/second max.
Liquidous Temperature (TL)
217°C
Time (tL) Maintained Above (TL)
60–150 seconds
Peak Body Package Temperature
260°C +0°C / –5°C
Time (tP) within 5°C of 260°C
30 seconds
Ramp-down Rate (TP to TL)
6°C/second max.
Time 25°C to Peak Temperature
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
8 minutes max.
www.fairchildsemi.com
10
Part Number
Package
Packing Method
FODM3063
Full Pitch Mini-Flat 4-Pin
Tube (100 units)
FODM3063R2
Full Pitch Mini-Flat 4-Pin
Tape and Reel (2500 Units)
FODM3063V
Full Pitch Mini-Flat 4-Pin, DIN EN/IEC60747-5-5 Option
Tube (100 Units)
FODM3063R2V
Full Pitch Mini-Flat 4-Pin, DIN EN/IEC60747-5-5 Option
Tape and Reel (2500 Units)
Note:
The product orderable part number system listed in this table also applies to the FODM3062, FODM3082 and
FODM3083 products.
Marking Information
1
3063
V X YY
3
4
R
2
6
5
Figure 13. Top Mark
Table 1. Top Mark Definitions
1
Fairchild Logo
2
Device Number
3
DIN EN/IEC60747-5-5 Option (only appears on component ordered with this option)
4
One-Digit Year Code, e.g., “6”
5
Digit Work Week, Ranging from “01” to “53”
6
Assembly Package Code
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
www.fairchildsemi.com
11
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Ordering Information
K0
P2
P0
t
D0
E
A0
W1
W
B0
d
F
D1
P
2.54 Pitch
Description
Symbol
Dimensions
Tape Width
W
12.00±0.4
Tape Thickness
t
0.35±0.02
Sprocket Hole Pitch
P0
4.00±0.20
Sprocket Hole Dia.
D0
1.55±0.20
Sprocket Hole Location
E
1.75±0.20
Pocket Location
F
5.50±0.20
P2
2.00±0.20
Pocket Pitch
P
8.00±0.20
Pocket Dimension
A0
4.75±0.20
Pocket Hole Dia.
B0
7.30±0.20
K0
2.30±0.20
D1
1.55±0.20
Cover Tape Width
W1
Cover Tape Thickness
d
Max. Component Rotation or Tilt
20° max
Devices Per Reel
2500
Reel Diameter
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
9.20
0.065±0.02
330 mm (13")
www.fairchildsemi.com
12
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Tape Specifications
FODM30XX — 4-Pin Full Pitch Mini-Flat Package Zero-Cross Triac Driver Output Optocouplers
Footprint Drawing for PCB Layout
0.80
1.00
6.50
2.54
Note:
All dimensions are in mm.
©2006 Fairchild Semiconductor Corporation
FODM30XX Rev. 1.2
www.fairchildsemi.com
13
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
© Semiconductor Components Industries, LLC
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
1
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
www.onsemi.com
工商网监
湘ICP备2023018690号
