ENW-C9A22C2EFN

SNAP PAN4561 The PAN4561 is an extended range 2.4GHz, ISM, RF module. Modules may be configured from simple point-to-point proprietary devices to complex mesh networks by choosing from different firmware options. Optional Synapse SNAP firmware provides a highly flexible, industry leading solution for mesh networking with a complete network development environment. The module uses the same FreeScale eight bit GT60 processor as Panasonic’s popular PAN4555 making the two products application compatible. The PAN4561 has 55 pins allowing access to the full functionality of the MC13213 SOC. Low noise and power amplifiers have been added to the PAN4561 for extended range. With a maximum transmit power of 20dBm and receive sensitivity of -105dBm this module has a link margin of 125dBm, giving it the best range in its class. Multiple antenna options are available including, ceramic antenna, SMD pad output, and U.FL connector. This module will comply to EN300328, FCC CFR Part 15 and ARIB STD-T66. FCC and IC certifications are pending. NEW! Product Performance: • • • • • • • • • • • • • • • Small Size: 35mm X 15mm X 3.5mm ut 3 Antenna Options: Single Port 50o, Ceramic Antenna or SMD Output 16 Selectable Channels With 250 Kbps In The 2.4 Ghz Band Low Power Modes For Increased Battery Life High Sensitivity: -105 dBm Typical At 1% Packet Error Rate 20 dBm Typical Output Power Programmable Over 30 dB Range Low Supply Voltage: 2.7 V To 3.3 V, 3.0 V Typical Operating Temperature Range: -40°C To +85°C Link Quality And Clear Channel Assessment Capability 60k Flash And 4k RAM Memory Two UARTs And One I2C Bus 8 Channel A/D Converter With 10 Bit For Fast And Easy Conversion From Analog Inputs (Temperature, Pressure And Fluid Levels) To Digital Values. 5 Channel 16 Bit Timer/Pulse Width Modulation (Tpm) Outputs BDM Port For Direct Download Programming 33 Digital I/O Lines With Programmable Pull-Ups And Several With High-Current Driver Part Numbers: Part Number Description ENWC9A22A1EF 8 bit, LNA, PA, with Ceramic Antenna, No SW ENWC9A22C1EF 8 bit, LNA, PA, with RF Out on SMD Pads, No SW ENWC9A22B1EF 8 bit, LNA, PA, with U. FL Ant Connector, No SW ENWC9A22A2EF 8 bit, LNA, PA, Ceramic Ant, SN55 FW ENWC9A22B2EF 8 bit, LNA, PA, U.FL Connector, SN55 FW ENWC9A22C2EF 8 bit, LNA, PA, SMD RF Out, SN55 FW ENWC9A22A4EF 8 bit, LNA, PA, Ceramic Ant, SNAP FW ENWC9A22C4EF 8 bit, LNA, PA, SMD RF Out, SNAP FW ENWC9A22B4EF 8 bit, LNA, PA, U.FL Connector, SNAP FW EVAL_PAN4561 Evaluation Kit For The PAN4561 Module Panasonic Electronic Components http://www.panasonic.com/rfmodules 1-800-344-2112 12 ® SNAP ® PAN4561 Applications: • • • • • Factory Automation • RFID Tagging Home Automation • Automated Meter Reading Motor/Lighting Control • Monitoring (Environmental, Patient, Fitness) Inventory Management Remote Control And Wire Replacement For Industrial Systems (Wireless Sensor Networks) Dimensions & Pin Layout: Pin No. PP $QWHQQD PP 1, 22, 32, GND 56 to 62  PP  3DG [PP[PP 3DG [PP[PP 7RS9LHZ 2 to 5 +HLJKW PP PP   23 / 24 Vcc 25 / 26 32 kHz Xtal 27 /Reset 28 CLKO 30 BKGD/MS (PTG0) VDDA 8 UART2 TxD (PTC0) 33 UART2 RxD (PTC1) I2C SDA 34 to 41 KBI0-7 (PTA0-7) 42 to 45 PTC7-4 10 11 12 to 19 Technical Specifications: Pin Name 6 9 Note: The pin names of the module and the internal MC1321x names fit to each other. All unmentioned pins are not connected and must be left open. TPM2CH1-4 (PTD4-7) Pin No. TPM2CH2 (PTD2) PP Parameter Pin Name (PTC2) I2C SCL (PTC3) ADC7-0 (PTB7-0) 46 UART1 TxD (PTE0) 47 UART1 RxD (PTE1) 52 /PA_PwrDn 20 ADC Ref. H 53 to 54 21 ADC Ref. L 55 GND 50 Ohm RF Value Condition / Notes -105 dBm typ. For 1% Packet Error Rate Output Power 20 dBm Maximal Power Supply 2.7 V ~ 3.3 V Single Supply, 3.0 V Typ. Receiver Sensitivity Power Control Range 30 dB Maximum Data Rate 250 kbps Current Consumption Receive Mode Transmit Mode Idle Mode Doze Mode Hibernate Mode Off Mode 45 mA typ. 202 mA typ. 1.6 mA typ. 50 uA typ. 16 uA typ. 2 uA Operating Temperature Range Over The Air Output Power Nominal Value No CLKO -40°C to +85°C Notes: All parameters are valid for VDD = 2.7V and Tamb = 25°C. Freescale‘s MC13213 is included with the module, SMAC, MAC or Freescale Bee-Stack. There is no additional license fee per module by using the Freescale Bee-Stack, only a one time general support fee ($500) for the Bee-Stack to be paid to Freescale. Mode Definitions and Transition Times for saving battery life can be seen in the data sheet MC1321x. The derivative MC13212 and MC13211 as well as a non-PA/LNA version are available on request. Maximum ratings shown for Tx power and Rx sensitivity, typical ratings may be lower. 13 Panasonic Electronic Components http://www.panasonic.com/rfmodules 1-800-344-2112