NXP Semiconductors
Data Sheet: Technical Data
MC9S08PL16S Data Sheet
Document Number MC9S08PL16S
Rev. 3, 06/2020
MC9S08PL16S
Supports: MC9S08PL16S and
MC9S08PL8S
Key features
• 8-Bit S08 central processor unit (CPU)
– Up to 20 MHz bus at 2.7 V to 5.5 V across operating
temperature range
– Supporting up to 30 interrupt/reset sources
– Supporting up to four-level nested interrupt
– On-chip memory
– Up to 1 KB random-access memory (RAM)
– Flash and RAM access protection
• Power-saving modes
– One low power stop mode; reduced power wait
mode
– Peripheral clock enable register can disable clocks to
unused modules, reducing currents; allows clocks to
remain enabled to specific peripherals in stop3 mode
• Clocks
– Internal Clock Source (ICS) — Internal clock source
module containing a frequency-locked-loop (FLL)
controlled by internal or external reference;
precision trimming of internal reference allows 0.2%
resolution; 1% deviation across temperature range of
0 ºC to 70ºC, 1.5% deviation across temperature
range of –40 ºC to 85 ºC; Up to 20 MHz
– Oscillator (XOSC) — Loop-controlled Pierce
oscillator; crystal or ceramic resonator range of
31.25 kHz to 39.0625 kHz or 4 MHz to 20 MHz
• System protection
– Watchdog with independent clock source
– Low-voltage detection with reset or interrupt;
selectable trip points
– Illegal opcode detection with reset
– Illegal address detection with reset
• Peripherals
– ADC - 12-channel, 10-bit resolution; 2.5 µs
conversion time; eight-level data FIFO with optional
watermark; automatic compare function; 1.7 mV/ºC
temperature sensor; internal bandgap reference
channel; operation in stop; optional hardware trigger
– FTM - Two flex timer modulators (FTM) modules
including one 6-channel (FTM2) and one 2-channel
(FTM0) backward compatible with TPM modules;
16-bit counter; each channel can be configured for
input capture, output compare, edge- or centeraligned PWM mode
– MTIM - One modulo timer with 8-bit prescaler and
overflow interrupt
– SCI - One serial communications interface (SCI/
UART) modules optional 13-bit break; Full duplex
non-return to zero (NRZ); LIN extension support
– I2C - One inter-integrated circuit module; up to 400
kbps; multi-master operation; programmable slave
address; supporting broadcast mode and 10-bit
addressing; supporting SMBUS
– ACMP - One analog comparator with both positive
and negative inputs; selectable voltage reference
provided by on-chip 6-bit DAC; separately
selectable interrupt on rising and falling comparator
output
– RTC - 16-bit real timer counter (RTC)
– CRC - Cyclic Redundancy Check with
programmable 16-/32-bit polynomial generator
– KBI — Up to 8 keyboard interrupt inputs
• Development support
– Single-wire background debug interface
– Breakpoint capability to allow three breakpoints
setting during in-circuit debugging
– On-chip in-circuit emulator (ICE) debug module
containing two comparators and nine trigger modes
• Input/Output
– Up to 18 GPIOs including one output-only pin
(PTA4)
– One 8-bit keyboard interrupt modules (KBI)
– One true open drain pin (PTB0)
NXP reserves the right to change the production detail specifications as may be
required to permit improvements in the design of its products.
• Package options
– 20-pin TSSOP
– 16-pin TSSOP
– 8-pin SOIC
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
2
NXP Semiconductors
Table of Contents
1
Overview............................................................................................ 4
6.2 Switching specifications............................................................ 17
1.1 MCU block diagram.................................................................. 4
6.2.1
Control timing..............................................................17
1.2 Peripheral register addresses......................................................5
6.2.2
Debug trace timing specifications................................18
1.3 System interconnection..............................................................5
6.2.3
FTM module timing.....................................................19
2
Orderable part numbers......................................................................6
3
Part identification............................................................................... 7
3.1 Description.................................................................................7
6.3 Thermal specifications...............................................................20
6.3.1
7
Thermal characteristics................................................ 20
Peripheral operating requirements and behaviors.............................. 21
3.2 Format........................................................................................7
7.1 External oscillator (XOSC) and ICS characteristics..................21
3.3 Fields..........................................................................................7
7.2 NVM specifications................................................................... 23
3.4 Example..................................................................................... 8
7.3 Analog........................................................................................24
4
Parameter Classification.....................................................................8
7.3.1
ADC characteristics..................................................... 24
5
Ratings................................................................................................9
7.3.2
Analog comparator (ACMP) electricals...................... 26
5.1 Thermal handling ratings...........................................................9
7.4 Communication interfaces......................................................... 27
5.2 Moisture handling ratings.......................................................... 9
5.3 ESD handling ratings.................................................................9
7.4.1
8
5.4 Voltage and current operating ratings........................................10
6
General............................................................................................... 11
6.1 Nonswitching electrical specifications...................................... 11
Inter-Integrated Circuit Interface (I2C) timing............ 27
Dimensions.........................................................................................28
8.1 Obtaining package dimensions.................................................. 28
9
Pinout................................................................................................. 28
9.1 Signal multiplexing and pin assignments.................................. 28
6.1.1
DC characteristics........................................................ 11
9.2 Device pin assignment...............................................................29
6.1.2
Supply current characteristics...................................... 15
10 Hardware design consideration.......................................................... 30
6.1.3
EMC performance........................................................16
11 Revision history................................................................................. 31
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
NXP Semiconductors
3
Overview
1 Overview
1.1 MCU block diagram
The block diagram below shows the structure of the MCUs.
Port A
PTA0/KBI0P0/FTM0CH0/ACMP0IN0/ADP0
PTA1/KBI0P1/FTM0CH1/ACMP0IN1/ADP1
PTA2/KBI0P2/RxD0/SDA/ADP2
PTA3/KBI0P3/TxD0/SCL/ADP3
1
PTA4/FTM0CH1O/ACMP0O/BKGD/MS
PTA5/IRQ/FTM0CH0/TCLK0/RESET
Port B
KEYBOARD INTERRUPT
PTB0/KBI0P4/RxD0/ADP4
PTB1/KBI0P5/TxD0/ADP5
PTB2/KBI0P6/SDA/ADP6
PTB3/KBI0P7/SCL/TCLK2/ADP7
PTB4/FTM2CH4
PTB5/FTM2CH5
PTB6/SDA/XTAL
PTB7/SCL/EXTAL
Port C
HCS08 CORE
PTC0/FTM2CH0/ADP8
PTC1/FTM2CH1/ADP9
PTC2/FTM2CH2/ADP10
PTC3/FTM2CH3/ADP11
MODULE (KBI0)
CPU
BDC
8-BIT MODULO TIMER
(MTIM0)
SYSTEM CONTROL
MODULE (SYS)
WDG
IRQ
1 kHz OSC
LVD
INTERRUPT PRIORITY
CONTROLLER(IPC)
ON-CHIP ICE AND
DEBUG MODUE (DBG)
USER FLASH
MC9S08PL16S = 16,384 bytes
MC9S08PL8S = 8,192 bytes
2-CH FLEX TIMER
MODULE (FTM0)
2
6-CH FLEX TIMER
MODULE (FTM2)
SERIAL COMMUNICATION
INTERFACE (SCI0)
ANALOG COMPARATOR
(ACMP0)
REAL-TIME CLOCK
(RTC)
INTER-INTEGRATED
CIRCUIT BUS (IIC)
USER RAM
MC9S08PL16S = 1,024 bytes
MC9S08PL8S = 1,024 bytes
10 MHz INTERNAL CLOCK
SOURCE ( ICS)
EXTAL
XTAL
VDD
V SS
VSS
VREFH
VDDA
VREFL
VSSA
EXTERNAL OSCILLATOR
SOURCE (XOSC)
POWER MANAGEMENT
CONTROLLER (PMC)
12-CH 10-BIT
ANALOG-TO-DIGITAL
CONVERTER(ADC)
CYCLIC REDUNDANCY
CHECK (CRC)
1. PTA4/FTM0CH1O/ACMP0O/BKGD/MS is an output-only pin when used as port pin.
2. PTB0 operates as true-open drain when working as output.
Figure 1. MCU block diagram
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
4
NXP Semiconductors
Overview
1.2 Peripheral register addresses
The following table shows the register availability of the devices.
Table 1. Peripheral register addresses
Address
Size (Byte)
Peripheral
0x0000-0x0002
3
Port data
0x0010-0x0017
8
ADC
0x0018-0x001B
4
MTIM0
0x0020-0x002A
11
FTM0
0x002C-0x002F
4
ACMP0
0x003B-0x003B
1
IRQ
0x003C-0x003C
1
KBI0
0x003E-0x003F
2
IPC
0x3000-0x300B
12
SYS
0x300C-0x300F
4
SCG
0x3010-0x301F
16
DBG
0x3020-0x302C
13
NVM
0x3038-0x303C
5
ICS
0x303E-0x303E
1
OSC
0x3040-0x3041
2
PMC
0x304A-0x304B
2
SYS (ILLA)
0x3050-0x305A
11
IPC
0x3060-0x3068
9
CRC
0x306A-0x306F
6
RTC
0x3070-0x307B
12
I2C
0x307C-0x307D
2
KBI0
0x3080-0x3087
8
SCI0
0x30AC-0x30AD
2
ADC
0x30B0-0x30B2
3
Port output enable
0x30B8-0x30BA
3
Port input enable
0x30C0-0x30D6
23
FTM2
0x30EC-0x30EF
4
Port filter
0x30F0-0x30F2
3
Port pullup
0x30F8-0x30FF
8
SYS (UUID)
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
NXP Semiconductors
5
Orderable part numbers
1.3 System interconnection
This device contains a set of system-level logics for module-to-module interconnection
for flexible configuration. These interconnections provide the hardware trigger function
between modules with least software configuration, which is ideal for infrared
communication, serial communication baudrate detection, low-end motor control,
metering clock calibration, and other general-purpose applications.
RXDCE
00
01
10
11
ADC trg
ovf
RTC
ovf
MTIM0
1
0
SCI0
00
01
10
11
0
ovf
ICSOUT
1 o
DELAY
FTM0
RxD0
rxd
txd
0
TxD0
1
ch0
1
ch1
0
FTM0CH1
0
÷2N
BUSREF
+
ACMP0
–
1
FTM2
ADHWTS
RXDFE
FTMCHS
FTMES
ACMP output selection
SCI0 RxD filter
ch0
ch1
ch2
ch3
ch4
ch5
ACIC
FTM2CH0
1
0
FTM2CH1
FTM2CH2
FTM2CH3
FTM2CH4
FTM2CH5
RTCC
SCI0 TxD modulation
RTC capture
TXDME
SCI0 RxD capture
ADC hardware trigger
Figure 2. System interconnection diagram
2 Orderable part numbers
The following table summarizes the part numbers of the devices covered by this
document.
Table 2. Orderable part numbers summary
Feature
MC9S08PL16S
Part number
CTJ
MC9S08PL8S
CSC1
CTG
CTJ
CSC1
CTG
Max. frequency
(MHz)
20
20
20
20
20
20
Flash memory
(KB)
16
16
16
8
8
8
RAM (KB)
1
1
1
1
1
1
Table continues on the next page...
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
6
NXP Semiconductors
Part identification
Table 2. Orderable part numbers summary (continued)
Feature
MC9S08PL16S
Part number
CTJ
MC9S08PL8S
CSC1
CTG
CTJ
CSC1
CTG
10-bit ADC
12ch
8ch
4ch
12ch
8ch
4ch
ACMP
1
1
1
1
1
1
16-bit FlexTimer 6ch+2ch
2ch+2ch
2ch
6ch+2ch
2ch+2ch
2ch
8-bit Modulo
timer
1
1
1
1
1
1
RTC
Yes
Yes
Yes
Yes
Yes
Yes
I2C
1
1
1
1
1
1
SCI (LIN
Capable)
1
1
1
1
1
1
WCOP
Yes
Yes
Yes
Yes
Yes
Yes
CRC
Yes
Yes
Yes
Yes
Yes
Yes
KBI pins
8
8
4
8
8
4
GPIO
18
14
6
18
14
6
Package
20-TSSOP
16-TSSOP
8-SOIC
20-TSSOP
16-TSSOP
8-SOIC
1. To confirm current availability of ordererable part numbers, go to http://www.nxp.com and perform a part number search.
3 Part identification
3.1 Description
Part numbers for the chip have fields that identify the specific part. You can use the
values of these fields to determine the specific part you have received.
3.2 Format
Part numbers for this device have the following format:
MC 9 S08 PL AA S B CC
3.3 Fields
This table lists the possible values for each field in the part number (not all combinations
are valid):
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
NXP Semiconductors
7
Parameter Classification
Field
Description
Values
MC
Qualification status
• MC = fully qualified, general market flow
9
Memory
• 9 = flash based
S08
Core
• S08 = 8-bit CPU
PL
Device family
• PL
AA
Approximate flash size in KB
• 16 = 16 KB
• 8 = 8 KB
S
Sub-family
• S
B
Operating temperature range (°C)
• C = -40 to 85
CC
Package designator
• TJ = 20-TSSOP
• TG = 16-TSSOP
• SC = 8-SOIC
3.4 Example
This is an example part number:
MC9S08PL16SCTG
4 Parameter Classification
The electrical parameters shown in this supplement are guaranteed by various methods.
To give the customer a better understanding, the following classification is used and the
parameters are tagged accordingly in the tables where appropriate:
Table 3. Parameter Classifications
P
Those parameters are guaranteed during production testing on each individual device.
C
Those parameters are achieved by the design characterization by measuring a statistically relevant sample size
across process variations.
T
Those parameters are achieved by design characterization on a small sample size from typical devices under
typical conditions unless otherwise noted. All values shown in the typical column are within this category.
D
Those parameters are derived mainly from simulations.
NOTE
The classification is shown in the column labeled “C” in the
parameter tables where appropriate.
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
8
NXP Semiconductors
Ratings
5 Ratings
5.1 Thermal handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
TSTG
Storage temperature
–55
150
°C
1
TSDR
Solder temperature, lead-free
—
260
°C
2
1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life.
2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
5.2 Moisture handling ratings
Symbol
MSL
Description
Moisture sensitivity level
Min.
Max.
Unit
Notes
—
3
—
1
1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
5.3 ESD handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
VHBM
Electrostatic discharge voltage, human body model
-6000
+6000
V
1
VCDM
Electrostatic discharge voltage, charged-device model
-500
+500
V
2
Latch-up current at ambient temperature of 125 °C
-100
+100
mA
3
ILAT
1. Determined according to JEDEC Standard JESD22-A114, Electrostatic Discharge (ESD) Sensitivity Testing Human Body
Model (HBM).
2. Determined according to JEDEC Standard JESD22-C101, Field-Induced Charged-Device Model Test Method for
Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components.
3. Determined according to JEDEC Standard JESD78D, IC Latch-up Test.
• Test was performed at 125 °C case temperature (Class II).
• I/O pins pass +100/-100 mA I-test with IDD current limit at 400 mA.
• I/O pins pass +30/-100 mA I-test with IDD current limit at 1000mA.
• Supply groups pass 1.5 Vccmax.
• RESET_b pin was only tested with negative I-test due to product conditioning requirement.
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
NXP Semiconductors
9
Ratings
5.4 Voltage and current operating ratings
Absolute maximum ratings are stress ratings only, and functional operation at the
maxima is not guaranteed. Stress beyond the limits specified in below table may affect
device reliability or cause permanent damage to the device. For functional operating
conditions, refer to the remaining tables in this document.
This device contains circuitry protecting against damage due to high static voltage or
electrical fields; however, it is advised that normal precautions be taken to avoid
application of any voltages higher than maximum-rated voltages to this high-impedance
circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate
logic voltage level (for instance, either VSS or VDD) or the programmable pullup resistor
associated with the pin is enabled.
Symbol
Description
Min.
Max.
Unit
VDD
Supply voltage
–0.3
6.0
V
IDD
Maximum current into VDD
—
120
mA
Digital input voltage (except RESET, EXTAL, XTAL, or true
open drain pin )
–0.3
VDD + 0.3
V
Digital input voltage (true open drain pin )
-0.3
6
V
Analog1,
–0.3
VDD + 0.3
V
–25
25
mA
VDD – 0.3
VDD + 0.3
V
VDIO
VAIO
ID
VDDA
RESET, EXTAL, and XTAL input voltage
Instantaneous maximum current single pin limit (applies to all
port pins)
Analog supply voltage
1. All digital I/O pins, except open-drain pin , are internally clamped to VSS and VDD. is only clamped to VSS.
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
10
NXP Semiconductors
General
6 General
6.1 Nonswitching electrical specifications
6.1.1 DC characteristics
This section includes information about power supply requirements and I/O pin
characteristics.
Table 4. DC characteristics
Symbol
C
—
—
VOH
P
Operating voltage
Output high
voltage
All I/O pins, standarddrive strength
C
IOHT
VOL
D
Output high
current
P
Output low
voltage
Max total IOH for all
ports
VIH
D
P
C
VIL
Typical1
Max
Unit
—
2.7
—
5.5
V
5 V, Iload =
-5 mA
VDD - 0.8
—
—
V
3 V, Iload =
-2.5 mA
VDD - 0.8
—
—
V
5V
—
—
-100
mA
3V
—
—
-50
—
—
0.8
V
3 V, Iload =
2.5 mA
—
—
0.8
V
mA
All I/O pins, standard- 5 V, Iload = 5
drive strength
mA
C
IOLT
Min
Descriptions
P
C
Output low
current
Max total IOL for all
ports
5V
—
—
100
3V
—
—
50
Input high
voltage
All digital inputs
VDD>4.5V
0.70 × VDD
—
—
VDD>2.7V
0.75 × VDD
—
—
Input low
voltage
All digital inputs
VDD>4.5V
—
—
0.30 × VDD
V
V
VDD>2.7V
—
—
0.35 × VDD
Vhys
C
Input
hysteresis
All digital inputs
—
0.06 × VDD
—
—
mV
|IIn|
P
Input leakage
current
All input only pins
(per pin)
VIN = VDD or
VSS
—
0.1
1
µA
|IOZ|
P
Hi-Z (offstate) leakage
current
All input/output (per
pin)
VIN = VDD or
VSS
—
0.1
1
µA
|IOZTOT|
C
Total leakage All input only and I/O VIN = VDD or
combined for
VSS
all inputs and
Hi-Z pins
—
—
2
µA
RPU
P
30.0
—
50.0
kΩ
Pullup
resistors
All digital inputs,
when enabled (all I/O
pins other than PTB0)
—
Table continues on the next page...
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
NXP Semiconductors
11
Nonswitching electrical specifications
Table 4. DC characteristics (continued)
Symbol
C
RPU2
P
Pullup
resistors
PTB0 pin
IIC
D
DC injection
current3, 4, 5
Single pin limit
Min
Typical1
Max
Unit
—
30.0
—
60.0
kΩ
VIN < VSS,
VIN > VDD
-0.2
—
2
mA
-5
—
25
Descriptions
Total MCU limit,
includes sum of all
stressed pins
CIn
C
Input capacitance, all pins
—
—
—
7
pF
VRAM
C
RAM retention voltage
—
2.0
—
—
V
1. Typical values are measured at 25 °C. Characterized, not tested.
2. The specified resistor value is the actual value internal to the device. The pullup value may appear higher when measured
externally on the pin.
3. All functional non-supply pins, except for PTB0, are internally clamped to VSS and VDD.
4. Input must be current-limited to the value specified. To determine the value of the required current-limiting resistor,
calculate resistance values for positive and negative clamp voltages, then use the large one.
5. Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current
conditions. If the positive injection current (VIn > VDD) is higher than IDD, the injection current may flow out of VDD and could
result in external power supply going out of regulation. Ensure that external VDD load will shunt current higher than
maximum injection current when the MCU is not consuming power, such as no system clock is present, or clock rate is
very low (which would reduce overall power consumption).
Table 5. LVD and POR Specification
Symbol
C
Description
POR re-arm
Min
Typ
Max
Unit
1.5
1.75
2.0
V
4.2
4.3
4.4
V
Level 1 falling
(LVWV = 00)
4.3
4.4
4.5
V
Level 2 falling
(LVWV = 01)
4.5
4.5
4.6
V
Level 3 falling
(LVWV = 10)
4.6
4.6
4.7
V
Level 4 falling
(LVWV = 11)
4.7
4.7
4.8
V
voltage1, 2
VPOR
D
VLVDH
C
VLVW1H
C
VLVW2H
C
VLVW3H
C
VLVW4H
C
VHYSH
C
High range low-voltage
detect/warning hysteresis
—
100
—
mV
VLVDL
C
Falling low-voltage detect
threshold - low range (LVDV =
0)
2.56
2.61
2.66
V
VLVDW1L
C
Level 1 falling
(LVWV = 00)
2.62
2.7
2.78
V
VLVDW2L
C
Level 2 falling
(LVWV = 01)
2.72
2.8
2.88
V
VLVDW3L
C
Level 3 falling
(LVWV = 10)
2.82
2.9
2.98
V
Falling low-voltage detect
threshold - high range (LVDV
= 1)3
Falling lowvoltage
warning
threshold high range
Falling lowvoltage
warning
threshold low range
Table continues on the next page...
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
12
NXP Semiconductors
Nonswitching electrical specifications
Table 5. LVD and POR Specification (continued)
1.
2.
3.
4.
Symbol
C
Description
Min
Typ
Max
Unit
VLVDW4L
C
Level 4 falling
(LVWV = 11)
2.92
3.0
3.08
V
VHYSDL
C
Low range low-voltage detect
hysteresis
—
40
—
mV
VHYSWL
C
Low range low-voltage
warning hysteresis
—
80
—
mV
VBG
P
Buffered bandgap output 4
1.14
1.16
1.18
V
Maximum is highest voltage that POR is guaranteed.
POR ramp time must be longer than 20us/V to get a stable startup.
Rising thresholds are falling threshold + hysteresis.
Voltage factory trimmed at VDD = 5.0 V, Temp = 25 °C
0.4
VDD-VOH (V)
0.3
85°C
0.2
25 °C
-40 °C
0.1
0
1
2
3
4
5
IOH (mA)
Figure 3. Typical IOH Vs. VDD-VOH (standard drive strength) (VDD = 5 V)
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
NXP Semiconductors
13
Nonswitching electrical specifications
0.6
VDD-VOH (V)
0.5
0.4
85°C
0.3
25 °C
0.2
-40 °C
0.1
0
1
2
3
4
5
IOH (mA)
Figure 4. Typical IOH Vs. VDD-VOH (standard drive strength) (VDD = 3.5 V)
0.4
VOL (V)
0.3
85°C
0.2
25 °C
-40 °C
0.1
0
1
2
3
4
5
IOL (mA)
Figure 5. Typical IOL Vs. VOL (standard drive strength) (VDD = 5 V)
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
14
NXP Semiconductors
Nonswitching electrical specifications
0.5
VOL (V)
0.4
0.3
85°C
0.2
25 °C
-40 °C
0.1
0
1
2
3
4
5
IOL (mA)
Figure 6. Typical IOL Vs. VOL (standard drive strength) (VDD = 3.5 V)
6.1.2 Supply current characteristics
This section includes information about power supply current in various operating modes.
Table 6. Supply current characteristics in operating temperature range
Num
C
Parameter
Symbol
Bus Freq
VDD (V)
Typical1
Max
Unit
1
C
Run supply current FEI mode,
all modules on; run from flash
RIDD
20 MHz
5
mA
C
2
5.60
—
10 MHz
3.91
—
1 MHz
2.34
—
5.57
—
C
20 MHz
C
10 MHz
3.91
—
1 MHz
2.34
—
4.44
—
3.34
—
2.29
—
4.43
—
C
C
Run supply current FEI mode,
all modules off and gated; run
from flash
RIDD
20 MHz
3
5
10 MHz
1 MHz
C
20 MHz
3
C
10 MHz
3.34
—
1 MHz
2.29
—
mA
Table continues on the next page...
MC9S08PL16S Data Sheet, Rev. 3, 06/2020
NXP Semiconductors
15
Nonswitching electrical specifications
Table 6. Supply current characteristics in operating temperature range (continued)
Num
C
Parameter
Symbol
Bus Freq
VDD (V)
Typical1
Max
Unit
3
P
Run supply current FBE
mode, all modules on; run
from RAM
RIDD
20 MHz
5
5.52
7
mA
10 MHz
3.51
—
1 MHz
1.70
—
5.51
—
C
4
C
20 MHz
C
10 MHz
3.50
—
1 MHz
1.69
—
4.37
5.5
2.94
—
1.64
—
4.36
—
P
C
5
Run supply current FBE
mode, all modules off and
gated; run from RAM
RIDD
10 MHz
1 MHz
20 MHz
C
10 MHz
2.93
—
1 MHz
1.64
—
4.17
—
10 MHz
2.87
—
1 MHz
1.64
—
4.16
—
10 MHz
2.87
—
1 MHz
1.63
—
C
Wait mode current FEI mode,
all modules on
WIDD
C
7
5
C
C
6
20 MHz
3
C
20 MHz
20 MHz
S3IDD
C
Stop3 mode supply current
no clocks active (except 1
kHz LPO clock)2, 3
C
ADC adder to stop3
C
ADLPC = 1
3
5
3
—
5
1.3
—
—
3
1.2
—
—
—
5
85
—
—
—
3
80
—
—
—
5
126
—
3
123
—
mA
mA
µA
µA
ADLSMP = 1
ADCO = 1
MODE = 10B
ADICLK = 11B
8
C
LVD adder to stop34
C
1.
2.
3.
4.
µA
Data in Typical column was characterized at 5.0 V, 25 °C or is typical recommended value.
RTC adder cause
工商网监
湘ICP备2023018690号
