0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
MPC961CFA

MPC961CFA

  • 厂商:

    NXP(恩智浦)

  • 封装:

    LQFP32

  • 描述:

    IC ZDB CMOS LV 1:18 32-LQFP

  • 数据手册
  • 价格&库存
MPC961CFA 数据手册
Freescale Semiconductor, Inc. MOTOROLA Order this document by MPC961C/D SEMICONDUCTOR TECHNICAL DATA Low Voltage Zero Delay Buffer MPC961C Freescale Semiconductor, Inc... The MPC961 is a 2.5V or 3.3V compatible, 1:18 PLL based zero delay buffer. With output frequencies of up to 200MHz, output skews of 150ps the device meets the needs of the most demanding clock tree applications. • • • • • • • • LOW VOLTAGE ZERO DELAY BUFFER Fully Integrated PLL Up to 200MHz I/O Frequency LVCMOS Outputs Outputs Disable in High Impedance LVCMOS Reference Clock Options LQFP Packaging ±50ps Cycle–Cycle Jitter 150ps Output Skews The MPC961 is offered with two different input configurations. The MPC961C offers an LVCMOS reference clock while the MPC961P offers an LVPECL reference clock. When pulled high the OE pin will force all of the outputs (except QFB) into a high impedance state. Because the OE pin does not affect the QFB output, down stream clocks can be disabled without the internal PLL losing lock. FA SUFFIX 32–LEAD LQFP PACKAGE CASE 873A–02 The MPC961 is fully 2.5V or 3.3V compatible and requires no external loop filter components. All control inputs accept LVCMOS compatible levels and the outputs provide low impedance LVCMOS outputs capable of driving terminated 50 transmission lines. For series terminated lines the MPC961 can drive two lines per output giving the device an effective fanout of 1:36. The device is packaged in a 32 lead LQFP. W Q0 CCLK 50k FB_IN Q1 Ref PLL 100 – 200 MHz O Q2 50 – 100 MHz 1 Q3 FB 50k Q14 F_RANGE Q15 50k Q16 OE 50k QFB The MPC961C requires an external RC filter for the analog power supply pin VCCA. Please see applications section for details. Figure 1. MPC961C Logic Diagram 03/01  Motorola, Inc. 2001 For More Information On This Product, REV 1 1 Go to: www.freescale.com Freescale Semiconductor, Inc. VCC Q6 Q7 Q8 GND Q9 Q10 Q11 MPC961C 24 23 22 21 20 19 18 17 Q5 25 16 VCC Q4 26 15 Q12 Q3 27 14 Q13 GND 28 13 Q14 Q15 Q0 31 10 Q16 VCC 32 9 QFB 1 2 3 4 5 6 7 8 VCC 11 FB_IN 30 OE Q1 VCCA GND F_RANGE 12 NC 29 CCLK Q2 GND Freescale Semiconductor, Inc... MPC961C Figure 2. 32–Lead Pinout (Top View) Table 1: PIN CONFIGURATIONS Pin I/O Type Function CCLK Input LVCMOS PLL reference clock signal FB_IN Input LVCMOS PLL feedback signal input, connect to a QFB output F_RANGE Input LVCMOS PLL frequency range select OE Input LVCMOS Output enable/disable Q0 - Q16 Output LVCMOS Clock outputs QFB Output LVCMOS PLL feedback signal output, connect to a FB_IN GND Supply Ground Negative power supply VCCA Supply VCC PLL positive power supply (analog power supply). The MPC961C requires an external RC filter for the analog power supply pin VCCA. Please see applications section for details. VCC Supply VCC Positive power supply for I/O and core NC Not connected Table 2: FUNCTION TABLE Control Default 0 1 F_RANGE 0 PLL high frequency range. MPC961C input reference and output clock frequency range is 100 – 200 MHz PLL low frequency range. MPC961C input reference and output clock frequency range is 50 – 100 MHz OE 0 Outputs enabled Outputs disabled (high–impedance state) MOTOROLA For More Information On This Product, 2 Go to: www.freescale.com TIMING SOLUTIONS DL207 — Rev 0 Freescale Semiconductor, Inc. MPC961C Table 3: ABSOLUTE MAXIMUM RATINGS* Symbol Parameter Min Max Unit VCC Supply Voltage –0.3 3.6 V VIN DC Input Voltage –0.3 VCC + 0.3 V VOUT DC Output Voltage –0.3 VCC + 0.3 V IIN DC Input Current ±20 mA IOUT DC Output Current ±50 mA TS Storage Temperature Range 125 °C –40 * Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute–maximum–rated conditions is not implied. Freescale Semiconductor, Inc... Table 4: DC CHARACTERISTICS (VCC = 3.3V ± 5%, TA = –40° to 85°C) Symbol Characteristic Min Typ Max Unit Condition VIH Input HIGH Voltage 2.0 VCC + 0.3 V LVCMOS VIL VOH Input LOW Voltage –0.3 0.8 V LVCMOS Output HIGH Voltage 2.4 V VOL Output LOW Voltage IOH = –20mAa IOL = 20mAa ZOUT Output Impedance IIN Input Current CIN Input Capacitance 4.0 CPD Power Dissipation Capacitance 8.0 10 pF Per Output ICCA Maximum PLL Supply Current 2.0 5.0 mA VCCA Pin ICC Maximum Quiescent Supply Current mA All VCC Pins VTT Output Termination Voltage 0.55 14 VCC V 20 W ±120 µA pF B2 V a. The MPC961C is capable of driving 50Ω transmission lines on the incident edge. Each output drives one 50Ω parallel terminated transmission line to a termination voltage of VTT. Alternatively, the device drives up two 50Ω series terminated transmission lines. Table 5: AC CHARACTERISTICS (VCC = 3.3V ± 5%, TA = –40° to 85°C)a Max Unit fref Symbol Input Frequency Characteristic F_RANGE = 0 F_RANGE = 1 Min 100 50 200 100 MHz fmax Maximum Output Frequency F_RANGE = 0 F_RANGE = 1 100 50 200 100 MHz frefDC Reference Input Duty Cycle tr, tf TCLK Input Rise/Fall Time t(∅) Propagation Delay (static phase offset) tsk(O) Output–to–Output Skewb DCO Output Duty Cycle tr, tf Output Rise/Fall Time tPLZ,HZ Output Disable Time tPZL,LZ Output Enable Time tJIT(CC) Cycle–to–Cycle Jitter tJIT(PER) Period Jitter tJIT(∅) I/O Phase Jitter tlock Maximum PLL Lock Time 25 CCLK to FB_IN –80 F_RANGE = 0 F_RANGE = 1 42 45 s)c RMS (1 s) RMS (1 s) Condition 75 % 3.0 ns 0.8 to 2.0V 120 ps PLL locked 90 150 ps 50 50 55 55 % 1.0 ns 10 ns 10 ns 15 ps 10 ps 15 ns 10 ms 0.1 RMS (1 7.0 0.55 to 2.4V W a. AC characteristics apply for parallel output termination of 50 to VTT b. See applications section for part–to–part skew calculation c. See applications section for calculation for other confidence factors than 1 TIMING SOLUTIONS DL207 — Rev 0 Typ s For More Information On This Product, 3 Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. MPC961C Table 6: DC CHARACTERISTICS (VCC = 2.5V ± 5%, TA = –40° to 85°C) Freescale Semiconductor, Inc... Symbol Characteristic Min Typ Max Unit Condition VIH Input HIGH Voltage 1.7 VCC + 0.3 V LVCMOS VIL VOH Input LOW Voltage –0.3 0.7 V LVCMOS Output HIGH Voltage 1.8 V VOL Output LOW Voltage IOH = –15mAa IOL = 15mAa ZOUT Output Impedance IIN Input Current CIN Input Capacitance 4.0 CPD Power Dissipation Capacitance 8.0 10 pF Per Output ICCA Maximum PLL Supply Current 2.0 5.0 mA VCCA Pin ICC Maximum Quiescent Supply Current mA All VCC Pins 0.6 18 V 26 W ±120 µA pF B VTT Output Termination Voltage VCC 2 V a. The MPC961C is capable of driving 50Ω transmission lines on the incident edge. Each output drives one 50Ω parallel terminated transmission line to a termination voltage of VTT. Alternatively, the device drives up two 50Ω series terminated transmission lines. Table 7: AC CHARACTERISTICS (VCC = 2.5V ± 5%, TA = –40° to 85°C)a Max Unit fref Symbol Input Frequency Characteristic F_RANGE = 0 F_RANGE = 1 Min 100 50 Typ 200 100 MHz fmax Maximum Output Frequency F_RANGE = 0 F_RANGE = 1 100 50 200 100 MHz frefDC Reference Input Duty Cycle tr, tf TCLK Input Rise/Fall Time t(∅) Propagation Delay (static phase offset) tsk(O) Output–to–Output Skewb DCO Output Duty Cycle tr, tf Output Rise/Fall Time tPLZ,HZ Output Disable Time tPZL,LZ Output Enable Time tJIT(CC) Cycle–to–Cycle Jitter tJIT(PER) Period Jitter tJIT(∅) I/O Phase Jitter 25 CCLK to FB_IN –80 F_RANGE = 0 F_RANGE = 1 40 45 75 % 3.0 ns 0.7 to 1.7V 120 ps PLL locked 90 150 ps 50 50 60 55 % 1.0 ns 10 ns 10 ns 15 ps 10 ps 15 ns 10 ms 0.1 s)c RMS (1 s) RMS (1 s) RMS (1 tlock Maximum PLL Lock Time a. AC characteristics apply for parallel output termination of 50 to VTT b. See applications section for part–to–part skew calculation c. See applications section for calculation for other confidence factors than 1 7.0 W MOTOROLA Condition 0.6 to 1.8V s For More Information On This Product, 4 Go to: www.freescale.com TIMING SOLUTIONS DL207 — Rev 0 Freescale Semiconductor, Inc. MPC961C Freescale Semiconductor, Inc... Power Supply Filtering The MPC961C is a mixed analog/digital product and as such it exhibits some sensitivities that would not necessarily be seen on a fully digital product. Analog circuitry is naturally susceptible to random noise, especially if this noise is seen on the power supply pins. The MPC961C provides separate power supplies for the output buffers (VCC) and the phase–locked loop (VCCA) of the device. The purpose of this design technique is to isolate the high switching noise digital outputs from the relatively sensitive internal analog phase–locked loop. In a controlled environment such as an evaluation board this level of isolation is sufficient. However, in a digital system environment where it is more difficult to minimize noise on the power supplies a second level of isolation may be required. The simplest form of isolation is a power supply filter on the VCCA pin for the MPC961C. Figure 3. illustrates a typical power supply filter scheme. The MPC961C is most susceptible to noise with spectral content in the 10kHz to 10MHz range. Therefore the filter should be designed to target this range. The key parameter that needs to be met in the final filter design is the DC voltage drop that will be seen between the VCC supply and the VCCA pin of the MPC961C. From the data sheet the ICCA current (the current sourced through the VCCA pin) is typically 2mA (5mA maximum), assuming that a minimum of 2.375V (VCC = 3.3V or VCC = 2.5V) must be maintained on the VCCA pin. The resistor RF shown in Figure 3. must have a resistance of 270Ω (VCC = 3.3V) or 5 to 15Ω (VCC = 2.5V) to meet the voltage drop criteria. The RC filter pictured will provide a broadband filter with approximately 100:1 attenuation for noise whose spectral content is above 20kHz. As the noise frequency crosses the series resonant point of an individual capacitor it’s overall impedance begins to look inductive and thus increases with increasing frequency. The parallel capacitor combination shown ensures that a low impedance path to ground exists for frequencies well above the bandwidth of the PLL. RF = 270Ω for VCC = 3.3V RF = 5–15Ω for VCC = 2.5V adequate to eliminate power supply noise related problems in most designs. Driving Transmission Lines The MPC961C clock driver was designed to drive high speed signals in a terminated transmission line environment. To provide the optimum flexibility to the user the output drivers were designed to exhibit the lowest impedance possible. With an output impedance of less than 15Ω the drivers can drive either parallel or series terminated transmission lines. For more information on transmission lines the reader is referred to application note AN1091. In most high performance clock networks point–to–point distribution of signals is the method of choice. In a point–to–point scheme either series terminated or parallel terminated transmission lines can be used. The parallel technique terminates the signal at the end of the line with a 50Ω resistance to VCC/2. This technique draws a fairly high level of DC current and thus only a single terminated line can be driven by each output of the MPC961C clock driver. For the series terminated case however there is no DC current draw, thus the outputs can drive multiple series terminated lines. Figure 4. illustrates an output driving a single series terminated line vs two series terminated lines in parallel. When taken to its extreme the fanout of the MPC961C clock driver is effectively doubled due to its capability to drive multiple lines. MPC961 OUTPUT BUFFER IN 14Ω MPC961 OUTPUT BUFFER IN RS = 36Ω ZO = 50Ω OutA RS = 36Ω ZO = 50Ω OutB0 14Ω RS = 36Ω ZO = 50Ω OutB1 RF VCCA VCC 22 µF 10 nF MPC961C Figure 4. Single versus Dual Transmission Lines VCC 33...100 nF Figure 3. Power Supply Filter Although the MPC961C has several design features to minimize the susceptibility to power supply noise (isolated power and grounds and fully differential PLL) there still may be applications in which overall performance is being degraded due to system power supply noise. The power supply filter schemes discussed in this section should be TIMING SOLUTIONS DL207 — Rev 0 The waveform plots of Figure 5. show the simulation results of an output driving a single line vs two lines. In both cases the drive capability of the MPC961C output buffer is more than sufficient to drive 50Ω transmission lines on the incident edge. Note from the delay measurements in the simulations a delta of only 43ps exists between the two differently loaded outputs. This suggests that the dual line driving need not be used exclusively to maintain the tight output–to–output skew of the MPC961C. The output waveform in Figure 5. shows a step in the waveform, this step is caused by the impedance mismatch seen looking into the driver. The parallel combination of the 36Ω series resistor plus the output impedance does not match the parallel For More Information On This Product, 5 Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. MPC961C combination of the line impedances. The voltage wave launched down the two lines will equal: VL = VS ( Zo / (Rs + Ro +Zo)) Zo = 50Ω || 50Ω Rs = 36Ω || 36Ω Ro = 14Ω VL = 3.0 (25 / (18 + 14 + 25) = 3.0 (25 / 57) = 1.31V At the load end the voltage will double, due to the near unity reflection coefficient, to 2.62V. It will then increment towards the quiescent 3.0V in steps separated by one round trip delay (in this case 4.0ns). 2.5 VOLTAGE (V) Freescale Semiconductor, Inc... 3.0 OutA tD = 3.8956 OutB tD = 3.9386 2.0 In 1.5 SPICE level and IBIS output buffer models are available for engineers who want to simulate their specific interconnect schemes. Using the MPC961C in zero-delay applications Nested clock trees are typical applications for the MPC961C. Designs using the MPC961C as LVCMOS PLL fanout buffer with zero insertion delay will show significantly lower clock skew than clock distributions developed from CMOS fanout buffers. The external feedback option of the MPC961C clock driver allows for its use as a zero delay buffer. By using the QFB output as a feedback to the PLL the propagation delay through the device is virtually eliminated. The PLL aligns the feedback clock output edge with the clock input reference edge resulting a near zero delay through the device. The maximum insertion delay of the device in zero-delay applications is measured between the reference clock input and any output. This effective delay consists of the static phase offset, I/O jitter (phase or long-term jitter), feedback path delay and the output-to-output skew error relative to the feedback output. Calculation of part-to-part skew The MPC961C zero delay buffer supports applications where critical clock signal timing can be maintained across several devices. If the reference clock inputs of two or more MPC961C are connected together, the maximum overall timing uncertainty from the common CCLK input to any output is: 1.0 0.5 0 2 4 6 8 TIME (nS) 10 12 14 Figure 5. Single versus Dual Waveforms Since this step is well above the threshold region it will not cause any false clock triggering, however designers may be uncomfortable with unwanted reflections on the line. To better match the impedances when driving multiple lines the situation in Figure 6. should be used. In this case the series terminating resistors are reduced such that when the parallel combination is added to the output buffer impedance the line impedance is perfectly matched. MPC961 OUTPUT BUFFER tSK(PP) = t( ∅) + tSK(O) + tPD, LINE(FB) + tJIT( ∅)  CF This maximum timing uncertainty consist of 4 components: static phase offset, output skew, feedback board trace delay and I/O (phase) jitter: CCLKCommon QFBDevice 1 tJIT(∅) Any QDevice 1 +tSK(O) +t(∅) RS = 22Ω ZO = 50Ω RS = 22Ω ZO = 50Ω 14Ω QFBDevice2 Any QDevice 2 Max. skew 14Ω + 22Ω k 22Ω = 50Ω k 50Ω 25Ω = 25Ω Figure 6. Optimized Dual Line Termination MOTOROLA tPD,LINE(FB) –t(∅) tJIT(∅) +tSK(O) tSK(PP) Figure 7. MPC961C max. device-to-device skew Due to the statistical nature of I/O jitter a rms value (1 s) is specified. I/O jitter numbers for other confidence factors (CF) can be derived from Table 8. For More Information On This Product, 6 Go to: www.freescale.com TIMING SOLUTIONS DL207 — Rev 0 Freescale Semiconductor, Inc. MPC961C convection and thermal conductivity of package and board. This section describes the impact of these parameters on the junction temperature and gives a guideline to estimate the MPC961C die junction temperature and the associated device reliability. For a complete analysis of power consumption as a function of operating conditions and associated long term device reliability please refer to the application note AN1545. According the AN1545, the long-term device reliability is a function of the die junction temperature: Freescale Semiconductor, Inc... Table 8: Confidence Facter CF CF Probability of clock edge within the distribution ± 1s 0.68268948 ± 2s 0.95449988 ± 3s 0.99730007 ± 4s 0.99993663 ± 5s 0.99999943 ± 6s 0.99999999 The feedback trace delay is determined by the board layout and can be used to fine-tune the effective delay through each device. In the following example calculation a I/O jitter confidence factor of 99.7% (± 3s) is assumed, resulting in a worst case timing uncertainty from input to any output of -275 ps to 315 ps relative to CCLK: tSK(PP) = [–80ps...120ps] + [–150ps...150ps] + [(15ps –3)...(15ps 3)] + tPD, LINE(FB) tSK(PP) = [–275ps...315ps] + tPD, LINE(FB) @ Table 9: Die junction temperature and MTBF @ Junction temperature (°C) MTBF (Years) 100 20.4 110 9.1 120 4.2 130 2.0 Increased power consumption will increase the die junction temperature and impact the device reliability (MTBF). According to the system-defined tolerable MTBF, the die junction temperature of the MPC961C needs to be controlled and the thermal impedance of the board/package should be optimized. The power dissipated in the MPC961C is represented in equation 1. Due to the frequency dependence of the I/O jitter, Figure 8. “Max. I/O Jitter versus frequency” can be used for a more precise timing performance analysis. Where ICCQ is the static current consumption of the MPC961C, CPD is the power dissipation capacitance per output, (Μ)ΣCL represents the external capacitive output load, N is the number of active outputs (N is always 27 in case of the MPC961C). The MPC961C supports driving transmission lines to maintain high signal integrity and tight timing parameters. Any transmission line will hide the lumped capacitive load at the end of the board trace, therefore, ΣCL is zero for controlled transmission line systems and can be eliminated from equation 1. Using parallel termination output termination results in equation 2 for power dissipation. In equation 2, P stands for the number of outputs with a parallel or thevenin termination, VOL, IOL, VOH and IOH are a function of the output termination technique and DCQ is the clock signal duty cyle. If transmission lines are used ΣCL is zero in equation 2 and can be eliminated. In general, the use of controlled transmission line techniques eliminates the impact of the lumped capacitive loads at the end lines and greatly reduces the power dissipation of the device. Equation 3 describes the die junction temperature TJ as a function of the power consumption. Figure 8. Max. I/O Jitter versus frequency Power Consumption of the MPC961C and Thermal Management The MPC961C AC specification is guaranteed for the entire operating frequency range up to 200 MHz. The MPC961C power consumption and the associated long-term reliability may decrease the maximum frequency limit, depending on operating conditions such as clock frequency, supply voltage, output loading, ambient temperature, vertical P TOT +V @ CC ƪ P TOT I CCQ + ƪ )V @f CC I CCQ CLOCK )V @f ǒ CC @ N@C TJ f CLOCK,MAX TIMING SOLUTIONS DL207 — Rev 0 ȍ )ȍ ) ȍƪ PD CL M Ǔƫ +T )P @R A + C @ N1 @ V @ PD ǒ @ N@C ) CLOCK 2 CC ƪ TOT PD CL M DC Q P Ǔƫ @V @ I @ ǒV * V Ǔ ) ǒ1 * DC Ǔ @ I @ V OH thja * * ǒI @ V T J,MAX T A R thja CCQ Equation 1 CC CC CC OH ƫ Ǔ For More Information On This Product, 7 Go to: www.freescale.com Q OL OL ƫ Equation 2 Equation 3 Equation 4 MOTOROLA Freescale Semiconductor, Inc. MPC961C Where Rthja is the thermal impedance of the package (junction to ambient) and TA is the ambient temperature. According to Table 9, the junction temperature can be used to estimate the long-term device reliability. Further, combining equation 1 and equation 2 results in a maximum operating frequency for the MPC961C in a series terminated transmission line system. Convection, LFPM Rthja (1P2S board), K/W Still air 80 100 lfpm 70 200 lfpm 61 300 lfpm 57 400 lfpm 56 500 lfpm 55 200 If the calculated maximum frequency is below 200 MHz, it becomes the upper clock speed limit for the given application conditions. The following two derating charts describe the safe frequency operation range for the MPC961C. The charts were calculated for a maximum tolerable die junction temperature of 110°C, corresponding to an estimated MTBF of 9.1 years, a supply voltage of 3.3V and series terminated transmission line or capacitive loading. Depending on a given set of these operating conditions and the available device convection a decision on the maximum operating frequency can be made. There are no operating frequency limitations if a 2.5V power supply or the system specifications allow for a MTBF of 4 years (corresponding to a max. junction temperature of 120°C. 200 fMAX (AC) 180 OPERATING FREQUENCY (MHz) OPERATING FREQUENCY (MHz) Freescale Semiconductor, Inc... Table 10: Thermal package impedance of the 32ld LQFP TJ,MAX should be selected according to the MTBF system requirements and Table 9. Rthja can be derived from Table 10. The Rthja represent data based on 1S2P boards, using 2S2P boards will result in a lower thermal impedance than indicated below. TA = 85°C 160 140 120 100 80 60 Safe operation 40 20 fMAX (AC) 180 TA = 75°C 160 140 TA = 85°C 120 100 80 60 Safe operation 40 20 0 0 500 400 300 200 IFPM, CONVECTION 100 0 Figure 9. Maximum MPC961C frequency, VCC = 3.3V, MTBF 9.1 years, driving series terminated transmission lines 500 400 300 200 IFPM, CONVECTION 100 0 Figure 10. Maximum MPC961C frequency, VCC = 3.3V, MTBF 9.1 years, 4 pF load per line MPC961C DUT Pulse Generator Z = 50 ZO = 50Ω ZO = 50Ω W RT = 50Ω RT = 50Ω VTT VTT Figure 11. TCLK MPC961C AC test reference for Vcc = 3.3V and Vcc = 2.5V MOTOROLA For More Information On This Product, 8 Go to: www.freescale.com TIMING SOLUTIONS DL207 — Rev 0 Freescale Semiconductor, Inc. MPC961C VCC VCC 2 B GND VCC VCC 2 B CCLK GND VOH VCC 2 B GND VCC VCC 2 B FB_IN GND tSK(O) t(∅) The pin–to–pin skew is defined as the worst case difference in propagation delay between any similar delay path within a single device Freescale Semiconductor, Inc... Figure 12. Output–to–output Skew tSK(O) VCC VCC 2 B Figure 13. Propagation delay (tPD, static phase offset) test reference CCLK GND tP FB_IN T0 DC = tP /T0 x 100% TJIT 〈∅) = |T0 –T1 mean| The time from the PLL controlled edge to the non controlled edge, divided by the time between PLL controlled edges, expressed as a percentage The deviation in t0 for a controlled edge with respect to a t0 mean in a random sample of cycles Figure 14. Output Duty Cycle (DC) TN TN+1 TJIT(CC) = |TN –TN+1 | TJIT(PER) = |TN –1/f0 | T0 The variation in cycle time of a signal between adjacent cycles, over a random sample of adjacent cycle pairs Figure 16. Cycle–to–cycle Jitter tF Figure 15. I/O Jitter The deviation in cycle time of a signal with respect to the ideal period over a random sample of cycles Figure 17. Period Jitter VCC=3.3V 2.4 VCC=2.5V 1.8V 0.55 0.6V tR Figure 18. Output Transition Time Test Reference TIMING SOLUTIONS DL207 — Rev 0 For More Information On This Product, 9 Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. MPC961C OUTLINE DIMENSIONS A –T–, –U–, –Z– FA SUFFIX LQFP PACKAGE CASE 873A–02 ISSUE A 4X A1 32 0.20 (0.008) AB T–U Z 25 1 –U– –T– B V AE B1 DETAIL Y 17 8 V1 AE DETAIL Y 9 4X –Z– 9 0.20 (0.008) AC T–U Z S1 S DETAIL AD G –AB– 0.10 (0.004) AC AC T–U Z –AC– BASE METAL ÉÉ ÉÉ ÉÉ ÉÉ F 8X M_ R J D SECTION AE–AE H W K X DETAIL AD Q_ 0.250 (0.010) C E MOTOROLA M N 0.20 (0.008) SEATING PLANE GAUGE PLANE Freescale Semiconductor, Inc... P NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE –AB– IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DATUMS –T–, –U–, AND –Z– TO BE DETERMINED AT DATUM PLANE –AB–. 5. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE –AC–. 6. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.250 (0.010) PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE –AB–. 7. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. DAMBAR PROTRUSION SHALL NOT CAUSE THE D DIMENSION TO EXCEED 0.520 (0.020). 8. MINIMUM SOLDER PLATE THICKNESS SHALL BE 0.0076 (0.0003). 9. EXACT SHAPE OF EACH CORNER MAY VARY FROM DEPICTION. DIM A A1 B B1 C D E F G H J K M N P Q R S S1 V V1 W X MILLIMETERS MIN MAX 7.000 BSC 3.500 BSC 7.000 BSC 3.500 BSC 1.400 1.600 0.300 0.450 1.350 1.450 0.300 0.400 0.800 BSC 0.050 0.150 0.090 0.200 0.500 0.700 12_ REF 0.090 0.160 0.400 BSC 1_ 5_ 0.150 0.250 9.000 BSC 4.500 BSC 9.000 BSC 4.500 BSC 0.200 REF 1.000 REF For More Information On This Product, 10 Go to: www.freescale.com INCHES MIN MAX 0.276 BSC 0.138 BSC 0.276 BSC 0.138 BSC 0.055 0.063 0.012 0.018 0.053 0.057 0.012 0.016 0.031 BSC 0.002 0.006 0.004 0.008 0.020 0.028 12_ REF 0.004 0.006 0.016 BSC 1_ 5_ 0.006 0.010 0.354 BSC 0.177 BSC 0.354 BSC 0.177 BSC 0.008 REF 0.039 REF TIMING SOLUTIONS DL207 — Rev 0 Freescale Semiconductor, Inc. MPC961C Freescale Semiconductor, Inc... NOTES TIMING SOLUTIONS DL207 — Rev 0 For More Information On This Product, 11 Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... MPC961C Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447 Technical Information Center: 1–800–521–6274 JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3–20–1, Minami–Azabu. Minato–ku, Tokyo 106–8573 Japan. 81–3–3440–3569 ASIA / PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, 2, Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. 852–26668334 HOME PAGE: http://www.motorola.com/semiconductors/ MOTOROLA On This Product, 12 ◊For More Information Go to: www.freescale.com TIMING SOLUTIONS MPC961C/D DL207 — Rev 0
MPC961CFA 价格&库存

很抱歉,暂时无法提供与“MPC961CFA”相匹配的价格&库存,您可以联系我们找货

免费人工找货