NCP4620
150 mA, 10 V, Low Dropout
Regulator
The NCP4620 is a CMOS Linear voltage regulator with 150 mA
output current capability. The device is capable of operating with input
voltages up to 10 V, with high output voltage accuracy and low
temperature−drift coefficient. The NCP4620 is easy to use, with
output current fold−back protection and a thermal shutdown circuit
included. A Chip Enable function is included to save power by
lowering supply current.
http://onsemi.com
MARKING
DIAGRAMS
Features
•
•
•
•
•
•
•
•
•
•
•
•
Operating Input Voltage Range: 2.6 V to 10 V
Output Voltage Range: 1.2 V to 6.0 V (available in 0.1 V steps)
Output Voltage Accuracy: ±1.0%
Low Supply Current: 23 mA
Low Dropout: 165 mV (IOUT = 100 mA, VOUT = 3.3 V)
400 mV (IOUT = 150 mA, VOUT = 2.8 V)
High PSRR: 70 dB at 1 kHz
Line Regulation 0.02%/V Typ
Current Fold Back Protection
Thermal Shutdown Protection
Stable with Ceramic Capacitors
Available in SC−70 and SOT23 Packages
These are Pb−Free Devices*
Typical Applications
•
•
•
•
NCP4620x
VIN
C1
1m
CE
SOT−23−5
CASE 1212
XXX
XMM
1
XXXMM
1
XXXX, XXX= Specific Device Code
MM
= Date Code
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 14 of this data sheet.
Battery products powered by 2 Lithium Ion cells
Networking and Communication Equipment
Cameras, DVRs, STB and Camcorders
Toys, industrial applications
VIN
SC−70
CASE 419A
VOUT
VOUT
GND
C2
1m
Figure 1. Typical Application Schematic
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2012
May, 2012 − Rev. 4
1
Publication Order Number:
NCP4620/D
NCP4620
VIN
VOUT
VIN
Vref
Vref
Current Limit
Thermal Shutdown
CE
VOUT
CE
Current Limit
Thermal Shutdown
GND
GND
NCP4620Hxxxx
NCP4620Dxxxx
Figure 2. Simplified Schematic Block Diagram
PIN FUNCTION DESCRIPTION
Pin No.
SC−70
Pin No.
SOT23
5
1
VIN
Input pin
3
2
GND
Ground
1
3
CE
4
5
VOUT
2
4
NC
Pin Name
Description
Chip enable pin (Active “H”)
Output pin
No connection
ABSOLUTE MAXIMUM RATINGS
Rating
Symbol
Value
Unit
VIN
12.0
V
Output Voltage
VOUT
−0.3 to VIN + 0.3
V
Chip Enable Input
VCE
12.0
V
Output Current
IOUT
165
mA
PD
380
mW
Operating Temperature
TA
−40 to +85
°C
Maximum Junction Temperature
TJ
+150
°C
TSTG
−55 to +125
°C
ESD Capability, Human Body Model (Note 2)
ESDHBM
2000
V
ESD Capability, Machine Model (Note 2)
ESDMM
200
V
Input Voltage (Note 1)
Power Dissipation − SC−70
Power Dissipation − SOT23
420
Storage Temperature
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Refer to ELECTRICAL CHARACTERISTIS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)
ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115)
Latchup Current Maximum Rating tested per JEDEC standard: JESD78.
http://onsemi.com
2
NCP4620
THERMAL CHARACTERISTICS
Symbol
Value
Unit
Thermal Characteristics, SOT23
Thermal Resistance, Junction−to−Air
Rating
RqJA
238
°C/W
Thermal Characteristics, SC−70
Thermal Resistance, Junction−to−Air
RqJA
263
°C/W
ELECTRICAL CHARACTERISTICS −40°C ≤ TA ≤ 85°C; VIN = VOUT(NOM) + 1 V; IOUT = 1 mA, CIN = COUT = 0.47 mF, unless
otherwise noted. Typical values are at TA = +25°C.
Parameter
Test Conditions
Operating Input Voltage
Output Voltage
Output Voltage Temp. Coefficient
TA = +25°C
VOUT > 1.5 V
VOUT ≤ 1.5 V
−40°C ≤ TA ≤ 85°C
VOUT > 1.5 V
VOUT ≤ 1.5 V
Symbol
Min
VIN
VOUT
Max
Unit
2.6
10
V
x0.99
−15
x1.01
15
V
mV
x0.974
−40
x1.023
35
V
mV
−40°C ≤ TA ≤ 85°C
Typ
ppm/°C
±80
Line Regulation
VOUT(NOM) + 0.5 V or 2.6 V (whichever is higher)
≤ VIN ≤ 10 V
LineReg
0.02
0.2
%/V
Load Regulation
IOUT = 0.1 mA to 150 mA
LoadReg
5
40
mV
V
0.40
0.30
0.25
1.40
1.30
1.10
0.80
0.58
0.48
0.40
Dropout Voltage
IOUT = 150 mA
1.2 V ≤ VOUT < 1.3 V
1.3 V ≤ VOUT < 1.5 V
1.5 V ≤ VOUT < 1.8 V
1.8 V ≤ VOUT < 2.3 V
2.3 V ≤ VOUT < 3.0 V
3.0 V ≤ VOUT < 4.0 V
4.0 V ≤ VOUT < 6.0 V
Output Current
Short Current Limit
VDO
IOUT
VOUT = 0 V
150
mA
ISC
40
IQ
23
40
mA
VIN = 10 V, VCE = 0 V, TA = 25°C
ISTB
0.1
1.0
mA
CE Input Voltage “H”
VCEH
CE Input Voltage “L”
VCEL
ICEPD
0.3
mA
VIN = VOUT + 1 V or 3.0 V whichever is higher,
DVIN = 0.2 Vpk−pk, IOUT = 30 mA, f = 1 kHz
PSRR
70
dB
f = 10 Hz to 100 kHz, IOUT = 30 mA, VOUT =
1.5 V, VIN = 2.6 V
VN
90
mVrms
VIN = 7 V, VCE = 0 V
RLOW
250
W
Thermal Shutdown Temperature
TTSD
165
°C
Thermal Shutdown Release
TTSR
110
°C
Quiescent Current
Standby Current
CE Pin Threshold Voltage
CE Pull Down Current
Power Supply Rejection Ratio
Output Noise Voltage
Low Output N−ch Tr. On Resistance
http://onsemi.com
3
mA
V
1.7
0.8
NCP4620
TYPICAL CHARACTERISTICS
1.6
3.5
1.4
3.0
3.0 V
2.5
4.0 V
1.0
VOUT (V)
VOUT (V)
1.2
VIN = 2.6 V
2.8 V
0.8
0.6
3.7 V
4.0 V
5.0 V
2.0
1.5
1.0
0.4
0.5
0.2
0.0
VIN = 3.5 V
0
50
100
150
IOUT (mA)
200
250
0.0
0
50
Figure 3. Output Voltage vs. Output Current
1.5 V Version (TJ = 255C)
100
150
IOUT (mA)
200
250
300
Figure 4. Output Voltage vs. Output Current
3.3 V Version (TJ = 255C)
6.0
5.0
VIN = 5.2 V
5.4 V
6.0 V
7.0 V
VOUT (V)
4.0
3.0
2.0
1.0
0.0
0
50
100
150
IOUT (mA)
200
250
300
0.40
0.40
0.35
0.35
0.30
0.30
0.25
VDO (V)
VDO (V)
Figure 5. Output Voltage vs. Output Current
5.0 V Version (TJ = 255C)
TJ = 25°C
0.20
85°C
0.15
0.10
0.20
TJ = 25°C
0.15
85°C
0.10
−40°C
0.05
0.00
0.25
0.05
0
50
100
150
0.00
−40°C
0
50
100
IOUT (mA)
IOUT (mA)
Figure 6. Dropout Voltage vs. Output Current
3.3 V Version
Figure 7. Dropout Voltage vs. Output Current
5.0 V Version
http://onsemi.com
4
150
NCP4620
TYPICAL CHARACTERISTICS
1.55
1.53
3.33
1.52
3.32
1.51
3.31
1.50
1.49
3.30
3.29
1.48
3.28
1.47
3.27
1.46
3.26
1.45
−40
−20
0
20
40
60
TJ, JUNCTION TEMPERATURE (°C)
VIN = 4.3 V
3.34
VOUT (V)
VOUT (V)
3.35
VIN = 2.6 V
1.54
3.25
−40
80
Figure 8. Output Voltage vs. Temperature,
1.5 V Version
5.10
40
35
5.06
30
5.02
IGND (mA)
VOUT (V)
5.04
5.00
4.98
4.96
−20
0
20
40
60
1.5 V
15
0
80
0
2
4
6
8
10
TJ, JUNCTION TEMPERATURE (°C)
VIN, INPUT VOLTAGE (V)
Figure 10. Output Voltage vs. Temperature,
5.0 V Version
Figure 11. Supply Current vs. Input Voltage
30
1.8
1.6
VOUT = 5 V
25
VOUT (V)
3.3 V
20
IGND (mA)
3.3 V
20
5
4.92
1.5 V
15
10
1 mA
1.4
20 mA
1.2
50 mA
1.0
100 mA
0.8
IOUT = 150 mA
0.6
0.4
5
0
−40
VOUT = 5 V
25
10
4.94
4.90
−40
80
Figure 9. Output Voltage vs. Temperature,
3.3 V Version
VIN = 6.0 V
5.08
−20
0
20
40
60
TJ, JUNCTION TEMPERATURE (°C)
0.2
−20
0
20
40
60
0.0
80
0
TJ, JUNCTION TEMPERATURE (°C)
1
2
3
4
5
6
7
8
9
VIN, INPUT VOLTAGE (V)
Figure 12. Supply Current vs. Temperature
Figure 13. Output Voltage vs. Input Voltage,
1.5 V Version
http://onsemi.com
5
10
NCP4620
TYPICAL CHARACTERISTICS
3.5
6.0
3.0
5.0
1 mA
4.0
2.0
VOUT (V)
VOUT (V)
2.5
20 mA
1.5
50 mA
1.0
100 mA
0.5
IOUT = 150 mA
0.0
0
1
2
3.0
2.0
20 mA
3
4
5
6
7
VIN, INPUT VOLTAGE (V)
8
9
0.0
10
50 mA
100 mA
IOUT = 150 mA
1 mA
1.0
0
Figure 14. Output Voltage vs. Input Voltage,
3.3 V Version
1
2
3
4
5
6
7
VIN, INPUT VOLTAGE (V)
8
9
10
Figure 15. Output Voltage vs. Input Voltage,
5.0 V Version
120
120
100
100
80
80
30 mA
60
PSRR (dB)
PSRR (dB)
IOUT = 100 mA
1 mA
40
0.1
1
10
100
40
0.1
1
10
100
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 16. PSRR, 1.5 V Version, VIN = 3.5 V
Figure 17. PSRR, 3.3 V Version, VIN = 5.3 V
120
3.0
100
2.5
80
30 mA
60
1 mA
40
IOUT = 100 mA
0.1
1
10
FREQUENCY (kHz)
1000
2.0
1.5
1.0
0.5
20
0
0.01
1 mA
IOUT = 100 mA
0
0.01
1000
VN (mVrms/√Hz)
PSRR (dB)
60
20
20
0
0.01
30 mA
100
0
0.01
1000
Figure 18. PSRR, 5.0 V Version, VIN = 7.0 V
0.1
1
10
FREQUENCY (kHz)
100
1000
Figure 19. Output Voltage Noise, 1.5 V Version,
VIN = 2.6 V, IOUT = 30 mA
http://onsemi.com
6
NCP4620
TYPICAL CHARACTERISTICS
25
10
9.0
20
VN (mVrms/√Hz)
7.0
6.0
5.0
4.0
3.0
15
10
5
2.0
1.0
0
0.01
0.1
1
10
100
0
1000
0.01
0.1
1
10
100
1000
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 20. Output Voltage Noise, 3.3 V Version,
VIN = 4.3 V, IOUT = 30 mA
Figure 21. Output Voltage Noise, 5.0 V Version,
VIN = 6.0 V, IOUT = 30 mA
4.0
3.5
3.0
VIN (V)
VOUT (V)
2.5
1.51
1.50
1.49
1.48
1.47
0
10
20
30
40
50
t (ms)
60
70
80
90
100
Figure 22. Line Transients, 1.5 V Version,
tR = tF = 5 ms, IOUT = 30 mA
5.8
5.3
4.8
VIN (V)
4.3
VOUT (V)
VN (mVrms/√Hz)
8.0
3.31
3.30
3.29
3.28
3.27
0
10
20
30
40
50
t (ms)
60
70
80
90
Figure 23. Line Transients, 3.3 V Version,
tR = tF = 5 ms, IOUT = 30 mA
http://onsemi.com
7
100
NCP4620
TYPICAL CHARACTERISTICS
7.5
7.0
6.5
VIN (V)
VOUT (V)
6.0
5.01
5.00
4.99
4.98
4.97
0
10
20
30
40
50
t (ms)
60
70
80
90
100
Figure 24. Line Transients, 5.0 V version,
tR = tF = 5 ms, IOUT = 30 mA
125
100
75
25
1.52
0
1.50
IOUT (mA)
VOUT (V)
50
1.54
1.48
1.46
1.44
1.42
0
20
40
60
80
100 120 140 160 180 200
t (ms)
Figure 25. Load Transients, 1.5 V Version,
IOUT = 50 – 100 mA, tR = tF = 0.5 ms, VIN = 2.6 V
125
100
3.36
50
3.34
25
3.32
0
3.30
3.28
3.26
3.24
3.22
0
20
40
60
80
100 120 140 160 180 200
t (ms)
Figure 26. Load Transients, 3.3 V Version,
IOUT = 50 – 100 mA, tR = tF = 0.5 ms, VIN = 4.3 V
http://onsemi.com
8
IOUT (mA)
VOUT (V)
75
NCP4620
TYPICAL CHARACTERISTICS
125
100
75
25
5.05
0
5.00
IOUT (mA)
VOUT (V)
50
5.10
4.95
4.90
4.85
4.80
0
20
40
60
80
100 120 140 160 180 200
t (ms)
Figure 27. Load Transients, 5.0 V Version,
IOUT = 50 – 100 mA, tR = tF = 0.5 ms, VIN = 6.0 V
45
30
15
IOUT (mA)
VOUT (V)
0
1.54
1.52
1.50
1.48
1.46
1.44
1.42
0
20
40
60
80
100 120 140 160 180 200
t (ms)
Figure 28. Load Transients, 1.5 V Version,
IOUT = 1 – 30 mA, tR = tF = 0.5 ms, VIN = 2.6 V
45
30
15
IOUT (mA)
VOUT (V)
0
3.34
3.32
3.30
3.28
3.26
3.24
3.22
0
20
40
60
80
100 120 140 160 180 200
t (ms)
Figure 29. Load Transients, 3.3 V Version,
IOUT = 1 – 30 mA, tR = tF = 0.5 ms, VIN = 4.3 V
http://onsemi.com
9
NCP4620
TYPICAL CHARACTERISTICS
45
30
15
5.04
IOUT (mA)
VOUT (V)
0
5.02
5.00
4.98
4.96
4.94
4.92
0
20
40
60
80
100 120 140 160 180 200
t (ms)
Figure 30. Load Transients, 5.0 V Version,
IOUT = 1 – 30 mA, tR = tF = 0.5 ms, VIN = 6.0 V
200
150
100
0
1.7
1.6
IOUT (mA)
VOUT (V)
50
1.8
1.5
1.4
1.3
1.2
0
50
100 150 200 250 300 350 400 450 500
t (ms)
Figure 31. Load Transients, 1.5 V Version,
IOUT = 1 – 150 mA, tR = tF = 0.5 ms, VIN = 2.6 V
200
150
100
0
3.5
3.4
3.3
3.2
3.1
3.0
0
50
100 150 200 250 300 350 400 450 500
t (ms)
Figure 32. Load Transients, 3.3 V Version,
IOUT = 1 – 150 mA, tR = tF = 0.5 ms, VIN = 3.8 V
http://onsemi.com
10
IOUT (mA)
VOUT (V)
50
NCP4620
TYPICAL CHARACTERISTICS
200
150
100
0
5.4
5.2
IOUT (mA)
VOUT (V)
50
5.6
5.0
4.8
4.6
4.4
0
50
100 150 200 250 300 350 400 450 500
t (ms)
Figure 33. Load Transients, 5.0 V Version,
IOUT = 1 – 150 mA, tR = tF = 0.5 ms, VIN = 6.0 V
3
Chip Enable
2
1
VCE (V)
VOUT (V)
0
2.0
1.5
IOUT = 30 mA
1.0
IOUT = 150 mA
IOUT = 1 mA
0.5
0
−0.5
0
20
40
60
80
100 120 140 160 180 200
t (ms)
Figure 34. Start−up, 1.5 V Version, VIN = 2.6 V
6
Chip Enable
4
2
4.0
IOUT = 30 mA
3.0
2.0
IOUT = 150 mA
1.0
IOUT = 1 mA
0
−1.0
0
20
40
60
80
100 120 140 160 180 200
t (ms)
Figure 35. Start−up, 3.3 V Version, VIN = 4.3 V
http://onsemi.com
11
VCE (V)
VOUT (V)
0
NCP4620
TYPICAL CHARACTERISTICS
Chip Enable
9
6
3
4.0
IOUT = 30 mA
3.0
IOUT = 150 mA
2.0
1.0
IOUT = 1 mA
0
−1.0
VCE (V)
VOUT (V)
0
0
20
40
60
80
100 120 140 160 180 200
t (ms)
Figure 36. Start−up, 5.0 V Version, VIN = 6.0 V
6
4
2
4.0
3.0
IOUT = 30 mA
2.0
IOUT = 1 mA
1.0
0
−1.0
0
VCE (V)
VOUT (V)
Chip Enable
IOUT = 150 mA
0
200 400 600 800 1000 1200 1400 1600 1800 2000
t (ms)
Figure 37. Shutdown, 3.3 V Version D,
VIN = 4.3 V
http://onsemi.com
12
NCP4620
APPLICATION INFORMATION
Enable Operation
A typical application circuit for NCP4620 series is shown
in Figure 38.
VIN
NCP4620x
VIN
C1
1m
The enable pin CE may be used for turning the regulator
on and off. The IC is switched on when a high level voltage
is applied to the CE pin. The enable pin has an internal pull
down current source. If the enable function is not needed
connect CE pin to VIN.
VOUT
VOUT
CE
GND
C2
1m
Output Discharger
The D version includes a transistor between VOUT and
GND that is used for faster discharging of the output
capacitor. This function is activated when the IC goes into
disable mode.
Thermal
Figure 38. Typical Application Schematic
As a power across the IC increase, it might become
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and also the ambient
temperature affect the rate of temperature increase for the
part. When the device has good thermal conductivity
through the PCB the junction temperature will be relatively
low in high power dissipation applications.
Input Decoupling Capacitor (C1)
A 1 mF ceramic input decoupling capacitor should be
connected as close as possible to the input and ground pin of
the NCP4620. Higher values and lower ESR improves line
transient response.
Output Decoupling Capacitor (C2)
A 1 mF ceramic output decoupling capacitor is enough to
achieve stable operation of the IC. If a tantalum capacitor is
used, and its ESR is high, loop oscillation may result. The
capacitors should be connected as close as possible to the
output and ground pins. Larger values and lower ESR
improves dynamic parameters.
PCB layout
Make the VIN and GND line as large as practical. If their
impedance is high, noise pickup or unstable operation may
result. Connect capacitors C1 and C2 as close as possible to
the IC, and make wiring as short as possible.
http://onsemi.com
13
NCP4620
ORDERING INFORMATION
Nominal Output
Voltage
Description
Marking
Package
Shipping†
NCP4620DSN15T1G
1.5 V
Auto discharge
JBE
SOT−23
(Pb−Free)
3000 / Tape & Reel
NCP4620DSN30T1G
3.0 V
Auto discharge
JBX
SOT−23
(Pb−Free)
3000 / Tape & Reel
NCP4620DSN33T1G
3.3 V
Auto discharge
KBA
SOT−23
(Pb−Free)
3000 / Tape & Reel
NCP4620DSN50T1G
5.0 V
Auto discharge
KBT
SOT−23
(Pb−Free)
3000 / Tape & Reel
NCP4620HSN15T1G
1.5 V
Standard
JAE
SOT−23
(Pb−Free)
3000 / Tape & Reel
NCP4620HSN33T1G
3.3 V
Standard
KAA
SOT−23
(Pb−Free)
3000 / Tape & Reel
NCP4620HSN50T1G
5.0 V
Standard
KAT
SOT−23
(Pb−Free)
3000 / Tape & Reel
NCP4620DSQ18T1G
1.8 V
Auto discharge
AD08
SC−70
(Pb−Free)
3000 / Tape & Reel
NCP4620HSQ12T1G
1.2 V
Standard
AC01
SC−70
(Pb−Free)
3000 / Tape & Reel
NCP4620HSQ15T1G
1.5 V
Standard
AC05
SC−70
(Pb−Free)
3000 / Tape & Reel
NCP4620HSQ18T1G
1.8 V
Standard
AC08
SC−70
(Pb−Free)
3000 / Tape & Reel
NCP4620HSQ25T1G
2.5 V
Standard
AC16
SC−70
(Pb−Free)
3000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*To order other package and voltage variants, please contact your ON Semiconductor sales representative.
http://onsemi.com
14
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SOT−23 5−LEAD
CASE 1212−01
ISSUE A
DATE 28 JAN 2011
SCALE 2:1
A
5
E
1
A2
0.05 S
B
D
A1
4
2
L
3
L1
5X
e
E1
b
0.10
C
M
C B
A
S
S
C
RECOMMENDED
SOLDERING FOOTPRINT*
3.30
XXX = Specific Device Code
M = Date Code
G
= Pb−Free Package
(Note: Microdot may be in either location)
0.95
PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
DESCRIPTION:
98ASH70518A
SOT−23 5−LEAD
MILLIMETERS
MIN
MAX
--1.45
0.00
0.10
1.00
1.30
0.30
0.50
0.10
0.25
2.70
3.10
2.50
3.10
1.50
1.80
0.95 BSC
0.20
--0.45
0.75
XXX MG
G
0.85
0.56
DIM
A
A1
A2
b
c
D
E
E1
e
L
L1
GENERIC
MARKING DIAGRAM*
5X
5X
DOCUMENT NUMBER:
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSIONS: MILLIMETERS.
3. DATUM C IS THE SEATING PLANE.
A
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “ G”,
may or may not be present.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2019
www.onsemi.com
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
SC−88A (SC−70−5/SOT−353)
CASE 419A−02
ISSUE L
SCALE 2:1
A
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
G
5
4
−B−
S
1
2
DATE 17 JAN 2013
DIM
A
B
C
D
G
H
J
K
N
S
3
D 5 PL
0.2 (0.008)
B
M
M
N
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.031
0.043
0.004
0.012
0.026 BSC
--0.004
0.004
0.010
0.004
0.012
0.008 REF
0.079
0.087
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.80
1.10
0.10
0.30
0.65 BSC
--0.10
0.10
0.25
0.10
0.30
0.20 REF
2.00
2.20
J
GENERIC MARKING
DIAGRAM*
C
K
H
XXXMG
G
SOLDER FOOTPRINT
0.50
0.0197
XXX = Specific Device Code
M
= Date Code
G
= Pb−Free Package
0.65
0.025
0.65
0.025
0.40
0.0157
1.9
0.0748
SCALE 20:1
(Note: Microdot may be in either location)
*This information is generic. Please refer to
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “G”, may
or may not be present. Some products may
not follow the Generic Marking.
mm Ǔ
ǒinches
STYLE 1:
PIN 1. BASE
2. EMITTER
3. BASE
4. COLLECTOR
5. COLLECTOR
STYLE 2:
PIN 1. ANODE
2. EMITTER
3. BASE
4. COLLECTOR
5. CATHODE
STYLE 3:
PIN 1. ANODE 1
2. N/C
3. ANODE 2
4. CATHODE 2
5. CATHODE 1
STYLE 4:
PIN 1. SOURCE 1
2. DRAIN 1/2
3. SOURCE 1
4. GATE 1
5. GATE 2
STYLE 6:
PIN 1. EMITTER 2
2. BASE 2
3. EMITTER 1
4. COLLECTOR
5. COLLECTOR 2/BASE 1
STYLE 7:
PIN 1. BASE
2. EMITTER
3. BASE
4. COLLECTOR
5. COLLECTOR
STYLE 8:
PIN 1. CATHODE
2. COLLECTOR
3. N/C
4. BASE
5. EMITTER
STYLE 9:
PIN 1. ANODE
2. CATHODE
3. ANODE
4. ANODE
5. ANODE
DOCUMENT NUMBER:
DESCRIPTION:
98ASB42984B
STYLE 5:
PIN 1. CATHODE
2. COMMON ANODE
3. CATHODE 2
4. CATHODE 3
5. CATHODE 4
Note: Please refer to datasheet for
style callout. If style type is not called
out in the datasheet refer to the device
datasheet pinout or pin assignment.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
SC−88A (SC−70−5/SOT−353)
PAGE 1 OF 1
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2018
www.onsemi.com
onsemi,
, and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
onsemi Website: www.onsemi.com
◊
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
工商网监
湘ICP备2023018690号
