84320AYI-01LF

84320I-01 780MHz, Crystal-to-3.3V Differential LVPECL Frequency Synthesizer DATASHEET GENERAL DESCRIPTION FEATURES • Dual differential 3.3V LVPECL outputs The 84320I-01 is a general purpose, dual output Crystal-to-3.3V Differential LVPECLHigh Frequency Synthesizer. The 84320I-01 has a selectable TEST_CLK or crystal inputs. The VCOoperates at a frequency range of 620MHz to 780MHz. The VCO frequency is programmed in steps equal to thevalue of the input reference or crystal frequency. The VCO and output frequency can be programmed using theserial or parallel interfaces to the configuration logic. The low phase noise characteristics of the 84320I-01make it an ideal clock source for 10 Gigabit Ethernet, SONET, and Serial Attached SCSI applications. • Selectable crystal oscillator interface or LVCMOS/LVTTL TEST_CLK • Output frequency range: 77.5MHz to 780MHz • Crystal input frequency range: 14MHz to 40MHz • VCO range: 620MHz to 780MHz • Parallel or serial interface for programming counter and output dividers • Duty cycle: 44% - 56% (N > 1) • RMS period jitter: 2.0ps (typical) • RMS phase jitter at 155.52MHz, using a 38.88MHz crystal (12kHz to 20MHz): 2.38ps (typical) • RMS phase noise at 155.52MHz (typical) Offset Noise Power 100Hz ..................-90.5 dBc/Hz 1KHz ................-114.2 dBc/Hz 10KHz ................-123.6 dBc/Hz 100KHz ................-128.1 dBc/Hz • 3.3V supply voltage • -40°C to 85°C ambient operating temperature • Available in lead-free (RoHS 6) package PIN ASSIGNMENT BLOCK DIAGRAM XTAL_IN nP_LOAD VCO_SEL M0 M1 M2 M3 M4 32 31 30 29 28 27 26 25 M5 1 24 XTAL_OUT M6 2 23 TEST_CLK M7 3 22 XTAL_SEL M8 4 N0 5 N1 6 nc 7 VEE 8 84320I-01 32-Lead LQFP 7mm x 7mm x 1.4mm package body Y Package Top View 21 VCCA 20 S_LOAD 19 S_DATA 18 S_CLOCK 17 MR 9 10 11 12 13 14 15 16 VEE nFOUT0 FOUT0 VCCO nFOUT1 FOUT1 1 VCC TEST 84320I-01 REVISION C DECEMBER 17, 2014 ©2014 Integrated Device Technology, Inc. 84320I-01 DATA SHEET FUNCTIONAL DESCRIPTION NOTE: The functional description that follows describes operation using a 25MHz crystal. Valid PLL loop divider values for different crystal or input frequencies are defined in the Input Frequency Characteristics, Table 5, NOTE 1. and N output divider to a specific default state that will automatically occur during power-up. The TEST output is LOW when operating in the parallel input mode. The relation-ship between the VCO frequency, the crystal frequency and the M divider is defined as follows: fVCO = fxtal x M The 84320I-01 features a fully integrated PLL and therefore requires no external components for setting the loop bandwidth. A fundamental crystal is used as the input to the on-chip oscillator. The output of the oscillator is fed into the phase detector. A 25MHz crystal provides a 25MHz phase detector reference frequency. The VCO of the PLL operates over a range of 620MHz to 780MHz. The output of the M divider is also applied to the phase detector. The M value and the required values of M0 through M8 are shown in Table 3B to program the VCO Frequency Function Table. Valid M values for which the PLL will achieve lock for a 25MHz reference are defined as 25 ≤ M ≤ 31. The frequency out is defined as follows: FOUT = fVCO = fxtal x M N N Serial operation occurs when nP_LOAD is HIGH and S_LOAD is LOW. The shift register is loaded by sampling the S_DATA bits with the rising edge of S_CLOCK. The contents of the shift register are loaded into the M divider and N output divider when S_LOAD transitions from LOW-to-HIGH. The M divide and N output divide values are latched on the HIGH-to-LOW transition of S_LOAD. If S_LOAD is held HIGH, data at the S_DATA input is passed directly to the M divider and N output divider on each rising edge of S_CLOCK. The serial mode can be used to program the M and N bits and test bits T1 and T0. The internal registers T0 and T1 determine the state of the TEST output as follows: The phase detector and the M divider force the VCO output frequency to be M times the reference frequency by adjusting the VCO control voltage. Note that for some values of M (either too high or too low), the PLL will not achieve lock. The output of the VCO is scaled by a divider prior to being sent to each of the LVPECL output buffers. The divider provides a 50% output duty cycle. The programmable features of the 84320I-01 support two input modes to program the M divider and N output divider. The two input operational modes are parallel and serial. Figure 1 shows the timing diagram for each mode. In parallel mode, the nP_LOAD input is initially LOW. The data on inputs M0 through M8 and N0 and N1 is passed directly to the M divider and N output divider. On the LOW-to-HIGH transition of the nP_LOAD input, the data is latched and the M divider remains loaded until the next LOW transition on nP_LOAD or until a serial event occurs. As a result, the M and N bits can be hardwired to set the M divider T1 T0 TEST Output 0 0 LOW 0 1 S_Data, Shift Register Input 1 0 Output of M divider 1 1 CMOS Fout FIGURE 1. PARALLEL & SERIAL LOAD OPERATIONS *NOTE: The NULL timing slot must be observed. 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 2 REVISION C 12/17/14 84320I-01 DATA SHEET TABLE 1. PIN DESCRIPTIONS Number Name 1 M5 Input Type Description 2, 3, 4, 28, 29, 30, 31, 32 M6, M7, M8, M0, M1, M2, M3, M4 Input M divider inputs. Data latched on LOW-to-HIGH transition of nP_LOAD Pulldown input. LVCMOS / LVTTL interface levels. 5, 6 N0, N1 Input Pulldown 7 nc Unused 8, 16 VEE Power Negative supply pins. 9 TEST Output Test output which is ACTIVE in the serial mode of operation. Output driven LOW in parallel mode. LVCMOS/LVTTL interface levels. 10 VCC Power Core supply pin. 11, 12 FOUT1, nFOUT1 Output Differential output for the synthesizer. LVPECL interface levels. 13 VCCO Power Output supply pin. 14, 15 FOUT0, nFOUT0 Output Pullup Determines output divider value as defined in Table 3C, Function Table. LVCMOS / LVTTL interface levels. No connect. Differential output for the synthesizer. LVPECL interface levels. 17 MR Input Pulldown 18 S_CLOCK Input Pulldown 19 S_DATA Input Pulldown 20 S_LOAD Input Pulldown 21 VCCA Power 22 XTAL_SEL Input 23 TEST_CLK Input 24, 25 XTAL_OUT, XTAL_IN Input 26 nP_LOAD Input 27 VCO_SEL Input Active High Master Reset. When logic HIGH, forces the internal dividers are reset causing the true outputs FOUTx to go low and the inverted outputs nFOUTx to go high. When logic LOW, the internal dividers and the outputs are enabled. Assertion of MR does not affect loaded M, N, and T values. LVCMOS / LVTTL interface levels. Clocks in serial data present at S_DATA input into the shift register on the rising edge of S_CLOCK. LVCMOS/LVTTL interface levels. Shift register serial input. Data sampled on the rising edge of S_ CLOCK. LVCMOS/LVTTL interface levels. Controls transition of data from shift register into the dividers. LVCMOS / LVTTL interface levels. Analog supply pin. Pullup Selects between crystal or test inputs as the PLL reference source. Selects XTAL inputs when HIGH. Selects TEST_CLK when LOW. LVCMOS / LVTTL interface levels. Pulldown Test clock input. LVCMOS / LVTTL interface levels. Crystal oscillator interface. XTAL_IN is the input. XTAL_OUT is the output. Parallel load input. Determines when data present at M8:M0 is loaded Pulldown into M divider, and when data present at N1:N0 sets the N output divider value. LVCMOS / LVTTL interface levels. Determines whether synthesizer is in PLL or bypass mode. Pullup LVCMOS / LVTTL interface levels. NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values. TABLE 2. PIN CHARACTERISTICS Symbol Parameter Test Conditions Minimum Typical Maximum Units CIN Input Capacitance 4 pF RPULLUP Input Pullup Resistor 51 kΩ RPULLDOWN Input Pulldown Resistor 51 kΩ REVISION C 12/17/14 3 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 84320I-01 DATA SHEET TABLE 3A. PARALLEL AND SERIAL MODE FUNCTION TABLE Inputs Conditions MR nP_LOAD M N S_LOAD S_CLOCK S_DATA H X X X X X X Reset. Forces outputs LOW. L L Data Data X X X Data on M and N inputs passed directly to the M divider and N output divider. TEST output forced LOW. L ↑ Data Data L X X L H X X L ↑ Data L H X X ↑ L Data L H X X ↓ L Data M divider and N output divider values are latched. L H X X L X X Parallel or serial input do not affect shift registers. L H X X H ↑ Data Data is latched into input registers and remains loaded until next LOW transition or until a serial event occurs. Serial input mode. Shift register is loaded with data on S_DATA on each rising edge of S_CLOCK. Contents of the shift register are passed to the M divider and N output divider. S_DATA passed directly to M divider as it is clocked. NOTE: L = LOW H = HIGH X = Don’t care ↑ = Rising edge transition ↓ = Falling edge transition TABLE 3B. PROGRAMMABLE VCO FREQUENCY FUNCTION TABLE 256 128 64 32 16 8 4 2 1 M8 M7 M6 M5 M4 M3 M2 M1 M0 0 0 0 0 1 1 0 0 1 • • • • • • • • • • 700 28 0 0 0 0 1 1 1 0 0 • • • • • • • • • • • 775 31 0 0 0 0 1 1 1 1 1 VCO Frequency (MHz) M Divide 625 25 • NOTE 1: These M divide values and the resulting frequencies correspond to crystal or TEST_CLK input frequency of 25MHz. TABLE 3C. PROGRAMMABLE OUTPUT DIVIDER FUNCTION TABLE Inputs N1 N0 0 0 0 1 1 1 N Divider Value Output Frequency (MHz) Minimum Maximum 1 620 780 2 310 390 0 4 155 195 1 8 77.5 97.5 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 4 REVISION C 12/17/14 84320I-01 DATA SHEET ABSOLUTE MAXIMUM RATINGS Supply Voltage, VCC 4.6V Inputs, VI -0.5V to VCC + 0.5 V Outputs, VO (LVCMOS) -0.5V to VCCO + 0.5V Outputs, IO (LVPECL) Continuous Current Surge Current 50mA 100mA Package Thermal Impedance, θJA 47.9°C/W (0 lfpm) Storage Temperature, TSTG -65°C to 150°C NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V±5%, TA = -40°C TO 85°C Symbol Parameter Minimum Typical Maximum Units VCC Core Supply Voltage 3.135 3.3 3.465 V VCCA Analog Supply Voltage 3.135 3.3 3.465 V VCCO Output Supply Voltage 3.135 3.3 3.465 V IEE Power Supply Current 155 mA ICCA Analog Supply Current 22 mA Maximum Units Test Conditions TABLE 4B. LVCMOS / LVTTL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V±5%, TA = -40°C TO 85°C Symbol VIH VIL IIH IIL Parameter Input High Voltage Input Low Voltage Input High Current Input Low Current Test Conditions Minimum Typical VCO_SEL, XTAL_SEL, MR, S_LOAD, nP_LOAD, N0:N1, S_DATA, S_CLOCK, M0:M8 2 VCC + 0.3 V TEST_CLK 2 VCC + 0.3 V VCO_SEL, XTAL_SEL, MR, S_LOAD, nP_LOAD, N0:N1, S_DATA, S_CLOCK, M0:M8 -0.3 0.8 V TEST_CLK -0.3 1.3 V M0-M4, M6-M8, N0, N1, MR, S_CLOCK, TEST_CLK, S_ DATA, S_LOAD, nP_LOAD VCC = VIN = 3.465V 150 µA M5, XTAL_SEL, VCO_SEL VCC = VIN = 3.465V 5 µA M0-M4, M6-M8, N0, N1, MR, S_CLOCK, TEST_CLK, S_ DATA, S_LOAD, nP_LOAD VCC = 3.465V, VIN = 0V -5 µA M5, XTAL_SEL, VCO_SEL VCC = 3.465V, VIN = 0V -150 µA 2.6 V VOH Output High Voltage TEST; NOTE 1 VOL Output Low Voltage TEST; NOTE 1 0.5 NOTE 1: Outputs terminated with 50Ω to VCCO/2. REVISION C 12/17/14 5 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER V 84320I-01 DATA SHEET TABLE 4C. LVPECL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V±5%, TA = -40°C TO 85°C Symbol Parameter Test Conditions Minimum Typical Maximum Units VOH Output High Voltage; NOTE 1 VCCO - 1.4 VCCO - 0.9 V VOL Output Low Voltage; NOTE 1 VCCO - 2.0 VCCO - 1.7 V VSWING Peak-to-Peak Output Voltage Swing 0.6 1.0 V NOTE 1: Outputs terminated with 50 Ω to VCCO - 2V. See “Parameter Measurement Information” section, “3.3V Output Load Test Circuit”. TABLE 5. INPUT FREQUENCY CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V±5%, TA = -40°C TO 85°C Symbol fIN Parameter Input Frequency Test Conditions Minimum Typical Maximum Units TEST_CLK; NOTE 1 14 40 MHz XTAL_IN, XTAL_OUT; NOTE 1 14 40 MHz 50 MHz S_CLOCK NOTE 1: For the input crystal and TEST_CLK frequency range, the M value must be set for the VCO to operate within the 620MHz to780MHz range. Using the minimum input frequency of 14MHz, valid values of M are 45 M 55. Using the maximum frequency of 40MHz, valid values of M are 16 ≤ M ≤ 19. TABLE 6. CRYSTAL CHARACTERISTICS Parameter Test Conditions Minimum Mode of Oscillation Typical Maximum Units Fundamental Frequency 40 MHz Equivalent Series Resistance (ESR) 50 Ω Shunt Capacitance 7 pF Drive Level 1 mW 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 14 6 REVISION C 12/17/14 84320I-01 DATA SHEET TABLE 7. AC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V±5%, TA = -40°C TO 85°C Symbol Parameter FOUT Output Frequency tjit(per) Period Jitter, RMS; NOTE 1 tsk(o) Output Skew; NOTE 2, 3 tR / tF Output Rise/Fall Time tS tH Setup Time Hold Time Test Conditions Minimum Typical 77.5 fOUT > 100MHz 20% to 80% 2.0 100 Maximum Units 780 MHz 2.6 ps 15 ps 700 5 ns S_DATA to S_CLOCK 5 ns S_CLOCK to S_LOAD 5 ns M, N to nP_LOAD 5 ns S_DATA to S_CLOCK 5 ns S_CLOCK to S_LOAD odc Output Duty Cycle tPW Output Pulse Width tLOCK PLL Lock Time 5 ns N>1 49 51 % fOUT ≤ 625 44 56 % ƒ > 625 tPERIOD/2 - 150 tPERIOD/2 + 150 ps 1 ms See Parameter Measurement Information section. NOTE 1: Jitter performance using XTAL inputs. NOTE 2: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at the output differential cross points. NOTE 3: This parameter is defined in accordance with JEDEC Standard 65. REVISION C 12/17/14 ps M, N to nP_LOAD 7 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 84320I-01 DATA SHEET TYPICAL PHASE NOISE AT 155.52MHZ ➤ 0 -10 -20 OC-48 Sonet Bandpass Filter -30 -40 155.52MHz -50 RMS Phase Jitter (Random) 12kHz to 20MHz = 2.38ps (typical) -70 Raw Phase Noise Data ➤ -80 -90 -100 -110 -120 ➤ NOISE POWER dBc Hz -60 -130 -140 Phase Noise Result by adding Sonet Bandpass Filter to raw data -150 -160 -170 -180 -190 10 100 1k 10k 100k 1M 10M 100M OFFSET FREQUENCY (HZ) TYPICAL PHASE NOISE AT 622.08MHZ ➤ 0 -10 -20 OC-48 Sonet Bandpass Filter -30 -40 622.08MHz -50 Raw Phase Noise Data -60 ➤ -70 -80 -90 -100 -110 ➤ NOISE POWER dBc Hz RMS Phase Jitter (Random) 12kHz to 20MHz = 2.48ps (typical) -120 -130 Phase Noise Result by adding Sonet Bandpass Filter to raw data -140 -150 -160 -170 -180 -190 10 100 1k 10k 100k 1M 10M 100M OFFSET FREQUENCY (HZ) 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 8 REVISION C 12/17/14 84320I-01 DATA SHEET PARAMETER MEASUREMENT INFORMATION 3.3V OUTPUT LOAD AC TEST CIRCUIT OUTPUT SKEW PERIOD JITTER OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD RMS PHASE JITTER OUTPUT RISE/FALL TIME REVISION C 12/17/14 9 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 84320I-01 DATA SHEET APPLICATION INFORMATION POWER SUPPLY FILTERING TECHNIQUES As in any high speed analog circuitry, the power supply pins are vulnerable to random noise. The 84320I-01 provides separate power supplies to isolate any high switching noise from the outputs to the internal PLL. VCC, VCCA, and VCCO should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. To achieve optimum jitter performance, power supply isolation is required. Figure 2 illustrates how a 24Ω resistor along with a 10μF and a .01μF bypass capacitor should be connected to each VCCA pin. 3.3V VCC .01μF 24Ω VCCA .01μF 10μF FIGURE 2. POWER SUPPLY FILTERING RECOMMENDATIONS FOR UNUSED INPUT AND OUTPUT PINS INPUTS: OUTPUTS: CRYSTAL INPUT For applications not requiring the use of the crystal oscillator input, both XTAL_IN and XTAL_OUT can be left floating. Though not required, but for additional protection, a 1kΩ resistor can be tied from XTAL_IN to ground. TEST_CLK INPUT For applications not requiring the use of the test clock, it can be left floating. Though not required, but for additional protection, a 1kΩ resistor can be tied from the TEST_CLK to ground. LVCMOS OUTPUT All unused LVCMOS output can be left floating. We recommend that there is no trace attached. LVPECL OUTPUTS All unused LVPECL outputs can be left floating. We recommend that there is no trace attached. Both sides of the differential output pair should either be left floating or terminated. SELECT PINS All select pins have internal pull-ups and pull-downs; additional resistance is not required but can be added for additional protection. A 1kΩ resistor can be used. 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 10 REVISION C 12/17/14 84320I-01 DATA SHEET CRYSTAL INPUT INTERFACE A crystal can be characterized for either series or parallel mode operation. The 84320I-01 has a built-in crystal oscillator circuit. This interface can accept either a series or parallel crystal without additional components and generate frequencies with accuracy suitable for most applications. Additional accuracy can be achieved by adding two small capacitors C1 and C2 as shown in Figure 3. Figure 3. CRYSTAL INPUt INTERFACE TERMINATION FOR LVPECL OUTPUTS The clock layout topology shown below is a typical termination for LVPECL outputs. The two different layouts mentioned are recommended only as guidelines. drive 50Ω transmission lines. Matched impedance techniques should be used to maximize operating frequency and minimize signal distortion. Figures 4A and 4B show two different layouts which are recommended only as guidelines. Other suitable clock layouts may exist and it would be recommended that the board designers simulate to guarantee compatibility across all printed circuit and clock component process variations. FOUT and nFOUT are low impedance follower outputs that generate ECL/LVPECL compatible outputs. Therefore, terminating resistors (DC current path to ground) or current sources must be used for functionality. These outputs are designed to FIGURE 4A. LVPECL OUTPUT TERMINATION REVISION C 12/17/14 FIGURE 4B. LVPECL OUTPUT TERMINATION 11 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 84320I-01 DATA SHEET LAYOUT GUIDELINE layout in the actual system will depend on the selected component types, the density of the components, the density of the traces, and the stack up of the P.C. board. The schematic of the 84320I-01 layout example used in this layout guideline is shown in Figure 5A. The 84320I-01 recommended PCB board layout for this example is shown in Figure 5B. This layout example is used as a general guideline. The C2 C1 U1 X_OUT T_CLK XTAL_SEL VCCA S_LOAD S_DATA S_CLOCK MR VCC ICS84320i-01 TEST VCC FOUT1 nFOUT1 VCCO FOUT0 nFOUT0 VEE M5 M6 M7 M8 N0 N1 nc VEE 9 10 11 12 VCC 13 FOUT 14 FOUTN 15 16 1 2 3 4 5 6 7 8 M4 M3 M2 M1 M0 VCO_SEL nP_LOAD X_IN 32 31 30 29 28 27 26 25 X1 VCC 24 23 22 21 20 19 18 17 R7 10 REF_IN XTAL_SEL VCCA S_LOAD S_DATA S_CLOCK C11 0.01u C16 10u VCC R1 125 R3 125 Zo = 50 Ohm C14 0.1u TL1 C15 0.1u + Zo = 50 Ohm - nTL1 VCC=3.3V R2 84 R4 84 FIGURE 5A. SCHEMATIC OF RECOMMENDED LAYOUT 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 12 REVISION C 12/17/14 84320I-01 DATA SHEET The following component footprints are used in this layout example: • The differential 50Ω output traces should have the same length. All the resistors and capacitors are size 0603. • Avoid sharp angles on the clock trace. Sharp angle turns cause the characteristic impedance to change on the transmission lines. • Keep the clock traces on the same layer. Whenever possible, avoid placing vias on the clock traces. Placement of vias on the traces can affect the trace characteristic impedance and hence degrade signal integrity. • To prevent cross talk, avoid routing other signal traces in parallel with the clock traces. If running parallel traces is unavoidable, allow a separation of at least three trace widths between the differential clock trace and the other signal trace. The RC filter consisting of R7, C11, and C16 should be placed as close to the VCCA pin as possible. • Make sure no other signal traces are routed between the clock trace pair. CLOCK TRACES AND TERMINATION • The matching termination resistors should be located as close to the receiver input pins as possible. POWER AND GROUNDING Place the decoupling capacitors C14 and C15, as close as possible to the power pins. If space allows, placement of the decoupling capacitor on the component side is preferred. This can reduce unwanted inductance between the decoupling capacitor and the power pin caused by the via. Maximize the power and ground pad sizes and number of vias capacitors. This can reduce the inductance between the power and ground planes and the component power and ground pins. Poor signal integrity can degrade the system performance or cause system failure. In synchronous high-speed digital systems, the clock signal is less tolerant to poor signal integrity than other signals. Any ringing on the rising or falling edge or excessive ring back can cause system failure. The shape of the trace and the trace delay might be restricted by the available space on the board and the component location. While routing the traces, the clock signal traces should be routed first and should be locked prior to routing other signal traces. CRYSTAL The crystal X1 should be located as close as possible to the pins 25 (XTAL_IN) and 24 (XTAL_OUT). The trace length between the X1 and U1 should be kept to a minimum to avoid unwanted parasitic inductance and capacitance. Other signal traces should not be routed near the crystal traces. GND X1 C1 C2 VCC VIA U1 PIN 1 C16 C11 VCCA R7 Close to the input pins of the receiver TL1N C15 TL1 C14 TL1 R1 R2 TL1N R3 R4 TL1, TL21N are 50 Ohm traces and equal length FIGURE 5B. PCB BOARD LAYOUT FOR 84320I-01 REVISION C 12/17/14 13 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 84320I-01 DATA SHEET POWER CONSIDERATIONS This section provides information on power dissipation and junction temperature for the 84320I-01. Equations and example calculations are also provided. 1. Power Dissipation. The total power dissipation for the 84320I-01 is the sum of the core power plus the power dissipated in the load(s). The following is the power dissipation for VCC = 3.3V + 5% = 3.465V, which gives worst case results. NOTE: Please refer to Section 3 for details on calculating power dissipated in the load. • • Power (core)MAX = VCC_MAX * IEE_MAX = 3.465V * 155mA = 537.08mW Power (outputs)MAX = 30mW/Loaded Output pair If all outputs are loaded, the total power is 2 * 30mW = 60mW Total Power_MAX (3.465V, with all outputs switching) = 537.08mW + 60mW = 597.08mW 2. Junction Temperature. Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the device. The maximum recommended junction temperature for the devices is 125°C. The equation for Tj is as follows: Tj = θJA * Pd_total + TA Tj = Junction Temperature θJA = Junction-to-Ambient Thermal Resistance Pd_total = Total Device Power Dissipation (example calculation is in section 1 above) TA = Ambient Temperature In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance θJA must be used. Assuming a moderate air flow of 200 linear feet per minute and a multi-layer board, the appropriate value is 42.1°C/W per Table 8 below. Therefore, Tj for an ambient temperature of 85°C with all outputs switching is: 85°C + 0.597W * 42.1°C/W = 110.1°C. This is well below the limit of 125°C. This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow, and the type of board (single layer or multi-layer). TABLE 8. THERMAL RESISTANCE θJA FOR 32-PIN LQFP, FORCED CONVECTION θJA by Velocity (Linear Feet per Minute) Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 0 200 500 67.8°C/W 47.9°C/W 55.9°C/W 42.1°C/W 50.1°C/W 39.4°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 14 REVISION C 12/17/14 84320I-01 DATA SHEET 3. Calculations and Equations. The purpose of this section is to derive the power dissipated into the load. LVPECL output driver circuit and termination are shown in Figure 6. FIGURE 6. LVPECL DRIVER CIRCUIT AND TERMINATION To calculate worst case power dissipation into the load, use the following equations which assume a 50Ω load, and a termination voltage of VCCO- 2V. • For logic high, VOUT = VOH_MAX = VCCO_MAX – 0.9V (VCCO_MAX - VOH_MAX) = 0.9V • For logic low, VOUT = VOL_MAX = VCCO_MAX – 1.7V (VCCO_MAX - VOL_MAX) = 1.7V Pd_H is power dissipation when the output drives high. Pd_L is the power dissipation when the output drives low. Pd_H = [(VOH_MAX – (VCCO_MAX - 2V))/RL] * (VCCO_MAX - VOH_MAX) = [(2V - (VCCO_MAX - VOH_MAX))/RL] * (VCCO_MAX - VOH_MAX) = [(2V - 0.9V)/50Ω) * 0.9V = 19.8mW Pd_L = [(VOL_MAX – (VCCO_MAX - 2V))/RL] * (VCCO_MAX - VOL_MAX) = [(2V - (VCCO_MAX - VOL_MAX))/RL] * (VCCO_MAX - VOL_MAX) = [(2V - 1.7V)/50Ω) * 1.7V = 10.2mW Total Power Dissipation per output pair = Pd_H + Pd_L = 30mW REVISION C 12/17/14 15 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 84320I-01 DATA SHEET RELIABILITY INFORMATION TABLE 9. θJAVS. AIR FLOW TABLE FOR 32 LEAD LQFP θJA by Velocity (Linear Feet per Minute) Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 0 200 500 67.8°C/W 47.9°C/W 55.9°C/W 42.1°C/W 50.1°C/W 39.4°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TRANSISTOR COUNT The transistor count for 84320I-01 is: 3776 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 16 REVISION C 12/17/14 84320I-01 DATA SHEET PACKAGE OUTLINE - Y SUFFIX FOR 32 LEAD LQFP TABLE 10. PACKAGE DIMENSIONS JEDEC VARIATION ALL DIMENSIONS IN MILLIMETERS BBA SYMBOL MINIMUM NOMINAL N MAXIMUM 32 A -- A1 0.05 -- 0.15 A2 1.35 1.40 1.45 b 0.30 0.37 0.45 c 0.09 -- 0.20 -- D 9.00 BASIC D1 7.00 BASIC D2 5.60 Ref. E 9.00 BASIC E1 7.00 BASIC E2 5.60 Ref. e 1.60 0.80 BASIC L 0.45 0.60 0.75 θ 0° -- 7° ccc -- -- 0.10 Reference Document: JEDEC Publication 95, MS-026 REVISION C 12/17/14 17 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 84320I-01 DATA SHEET TABLE 11. ORDERING INFORMATION Part/Order Number Marking Package Shipping Packaging Temperature 84320AYI-01LF ICS4320AI01L 84320AYI-01LFT ICS4320AI01L 32 Lead “Lead-Free” LQFP tray -40°C to 85°C 32 Lead “Lead-Free” LQFP 1000 tape & reel -40°C to 85°C NOTE: Parts that are ordered with an “LF” suffix to the part number are the Pb-Free configuration and are RoHS compliant. 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER 18 REVISION C 12/17/14 84320I-01 DATA SHEET REVISION HISTORY SHEET Rev Table Page Description of Change A T11 18 Ordering Information Table - added LF marking 9/5/08 8/4/10 B T11 18 20 Updated datasheet’s header/footer with IDT from ICS. Removed ICS prefix from Part/Order Number column. Added Contact Page. C T11 18 Ordering Information Table - removed leaded devices, PDN CQ-13-02 expired REVISION C 12/17/14 19 Date 12/17/14 780MHZ, CRYSTAL-TO-3.3V DIFFERENTIAL LVPECL FREQUENCY SYNTHESIZER Corporate Headquarters 6024 Silver Creek Valley Road San Jose, California 95138 Sales 800-345-7015 or +408-284-8200 Fax: 408-284-2775 www.IDT.com Technical Support email: clocks@idt.com DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties. IDT’s products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners. Copyright 2014. All rights reserved. IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.